OSD Audio PS SERIES User manual

PS SERIES SUBWOOFER INSTALL GUIDE
PS10-12 manual.indd 1 3/21/16 8:19 AM

PS SERIES SUBWOOFER INSTALL GUIDE
Unpacking:
Installation Precautions:
Before disposing the packaging, check that nothing is left inside.
Before installing
Moving the unit
Before switching the unit on
Placement
Recycling
Open the box and carefully remove all staples, then remove subwoofer.
If you notice any defects on any elements during the unpacking process, contact your dealer.
Before connecting your subwoofer, make sure all equipment is switched off. Do not connect the subwoofer power supply cable before
completing all connections.
Always disconnect the power supply cable and any audio cables connected to the subwoofer before moving it. This will prevent a short
circuit or damage to any plugs or connecting cables.
Double check that all connections are correct and that the volume is turned all the way down.
Place the subwoofer in a cool area with sufcient ventilation. Avoid placing in damp area or areas exposed to excessive sunlight or
heat.
Your product contains valuable materials that can be recovered and recycled.
PS10-12 manual.indd 2 3/21/16 8:19 AM

Back Panel Description
1. Power plug
2. ON / OFF
3. Phase inversion button 0-180°
4. Crossover control
5. Volume control
6. Inputs
PS SERIES SUBWOOFER INSTALL GUIDE
1. 2.
3.
4.
5.
6.
PS10-12 manual.indd 3 3/21/16 8:19 AM

PS SERIES SUBWOOFER INSTALL GUIDE
Connections
Connecting To A Multi-Channel A/V Amplier
Before connecting your subwoofer, make sure all equipment is switched off. If you have any doubts about connecting your subwoofer,
we recommend you contact your local authorized dealer.
Use the SUBWOOFER OUT on the back of the A/V unit (RCA connectors) to connect it to one of the two inputs on the back of the
subwoofer as shown below.
A/V UNIT
SUBWOOFER OUT
PS10-12 manual.indd 4 3/21/16 8:19 AM

Connecting To A Stereo Amplier
Use the PRE-OUT (L+R) output on your pre-amp or stereo amplier (see owners manual) and connect then to the inputs on the
subwoofer as shown below.
STEREO AMPLIFIER
PS SERIES SUBWOOFER INSTALL GUIDE
L R
PS10-12 manual.indd 5 3/21/16 8:19 AM

PS SERIES SUBWOOFER INSTALL GUIDE
Powering ON
Positioning And Settings
Troubleshooting
Powering ON should be carried out as follows:
- Check that all connections are correct and that the volume of your amplier is set to minimum.
- Connect the power plug.
- Switch the ON/OFF switch to ON, the blue LED on the front panel will light up.
- Adjust the volume, frequency and phasing (see Settings).
- The standby is done automatically if no signal is received for 15 minutes, the LED on the front panel becomes red.
NOTE: Cut off the power supply of the subwoofer by using the power switch when it is not in use for several days.
Position your subwoofer in the forward listening zone (if possible between the two main speakers) for a better sound resolution.
This subwoofer can be used with any type of loudspeakers.
The ideal setting should correspond to a realistic reproduction of the bass and be adjusted to compliment your main loudspeakers.
You should not feel the subwoofer, the bass should appear to come from main speakers.
The phase inversion switch can be used to reach the best result possible. This switch is used to invert the phase of the sound
signals coming from the subwoofer. Depending on the placement of the subwoofer in the room in relation to the main speakers,
inverting the subwoofer phase can lead to a better coherence to the systems global response in the bass frequencies.
We recommend you to carry out various tests until nding the setting which suits you the best. Use a recording you know well and
study the result according to your taste and expectations.
If the equipment fails to operate correctly, check the points below. If the problem continues, a malfunction may be possible. Disconnect
the power supply immediately and contact your dealer.
PROBLEM CAUSE SOLUTION
The subwoofer is not working There is no power supply to the subwoofer Check these points in order:
- If the power supply cable is connected
- If the power plug is working
No sound is coming from the subwoofer There is no input signal to your subwoofer Check these points in order:
- If the is correctly connected to the amp
- If the A/V or stereo amplier is turned on
- If your A/V or stereo amplier has a
working source of sound (CD, DVD, etc..)
The level of sound is weak, although the
subwoofer volume is at maximum
Incorrect adjustment of A/V amplier Check the subwoofer setting at the A/V
amplier (see owners manual)
PS10-12 manual.indd 6 3/21/16 8:19 AM

Specications
Warranty Information
Spec PS 10 PS 12
Power 200W 300W
Woofer 10” 12”
Frequency 38-120 Hz 30-120 Hz
Phase 0-180° 0-180°
Input L&R Low Level L&R Low Level
Dimensions 13.5 x 14 x 15” 15.5 x 15.5 x 15.5”
Weight 19.5 lbs 27 lbs
PS SERIES SUBWOOFER INSTALL GUIDE
All OSD AUDIO electronics have (2) year Limited Warranty against defects in materials and workmanship. Proof of purchase must accompany all
claims. During the warranty period OSD AUDIO will replace any defective part and correct any defect in workmanship without charge for either parts or
labor
OSD AUDIO may replace returned electronics with a product of equal value and performance. In such cases, some modications to the mounting may
be necessary and are not OSD AUDIO’s responsibility.
For this warranty to apply, the unit must be installed and used according to its written instructions. If necessary, repairs must be performed by OSD
AUDIO. The unit must be returned to OSD AUDIO at the owner’s expense and with prior written permission. Accidental damage and shipping damage
are not considered defects, nor is damaged resulting from abuse or from servicing performed by an agency or person not specically authorized in
writing by OSD Audio
OSD AUDIO sells products only through authorized dealers and distributors to ensure that customers obtain proper support and service. Any OSD
AUDIO product purchased from an unauthorized dealer or other source, including retailers, mail order dealers and online sellers will not be honored or
serviced under existing OSD AUDIO warranty policy. Any sale of product by an unauthorized source or other manner not authorized by OSD AUDIO
shall void the warranty on the applicable product.
Damage to or destruction of components due to application of excessive power voids the warranty on those parts. In these cases, repairs will be made
on the basis of the retail value of the parts and labor. To return for repairs, you must email customer service at [email protected] for a Returned
Merchandise Authorization (RMA) number then the unit must be shipped to OSD AUDIO at the owner’s expense, along with a note explaining the
nature of service required. Be sure to pack the product(s) in a corrugated container with at least 3 inches of resilient material to protect the unit from
damage in transit.
This Warranty Does Not Cover: Damage caused by abuse, accident, misuse, negligence, or improper operation (installation) • Any products that have
been altered or modied • Any product whose identifying number of decal, serial #, etc. has been altered, defaced or removed • Normal wear and
maintenance.
PS10-12 manual.indd 7 3/21/16 8:19 AM

PS Sub Manual 3/16
OSD Audio | Brea, CA | osdaudio.com
PS10-12 manual.indd 8 3/21/16 8:19 AM