Outsider Street 1250 Installation instructions manual

01
19-09-2022
PLATEAU STREET
#207 MOUNTING GUIDE
Kigkurren 8A Islands Brygge DK2300 Copenhagen · out-sider.dk

02
19-09-2022
Street 1250/1800
• 3 pcs M8x90
• 3 pcs M8 nut
• 6 pcs M8 washer
• 12 pcs M8x16
PLATEAU PICNIC STREET
Developed by out-sider in collaboration with Holscher Design 2021.
INDEX: PAGE
Item list ......................................................................................02
Assembling legs and table........................................................03
Assembling laminate seats to the legs....................................04
Assembling seats to table frame.............................................04
Fixation of Point Sun..................................................................05
Cleaning and maintenance .....................................................06
ITEM LIST ADDONS
Add-ons, are not included with standard product
1x Point Sun #326
f. Seat
2x Short leg with lange
(207 9012)
2x Street leg (207 9231)
1x logo disc
(195 9040)
3x Seat 1800 or Seat 1250 #195
2x disc
(195 9041)
POINT SUN BASE 3
319 7003
Tools (not included)
• Allen key set
• Socket wrench set
• Screws and bolts for the mounting of the surface bracket

03
19-09-2022
ASSEMBLING LEGS AND TABLE
A: Place the table on a soft surface bottom up. Screw on the two legs (207 9231) with the included M8x16 countersunk screws, two for each leg.
B: Flip the table and insert the disc with a logo into the hole in the tabletop. Make sure the disc is lat and lush with the surface. Use the M8x90,
washers, and M8 nut to fasten the disc to the frame.
ATTENTION
- Only place laminate on a safe, or
soft surface to prevent damage to the
laminate.
A B
Nut
Washer
M8x90
Logo disc
M8x16
M8x16
Washer

04
19-09-2022
ASSEMBLING LAMINATE SEATS TO LEGS
Place the seats on a soft surface bottom up. Screw the small leg (207 9012) on the opposite end of
the irst leg with the included M8x16 countersunk screws, two for each leg. Repeat the procedure
with the other seat and leg.
ATTENTION
- Only place laminate on a safe, or
soft surface to prevent damage to the
laminate.
- Repeat procedure with the next
1800/1250 seat for 207 Street.
M8x16

05
19-09-2022
450,00
A
ASSEMBLING SEATS TO TABLE FRAME
Place the two seats on the legs attached to the table and screw them on with the included M8x16
countersunk screws, two for each leg. Then insert the two discs without logos into the holes in the
seats. Make sure the disc is lat and lush with the surface. Use the M8x100, washers, and M8 nuts
to fasten the discs to the frame.
M8x16
M8x16

06
19-09-2022
MOUNTING OF POINT SUN
Place the Point Sun light unit in the base, align the holes and tighten the safety set screw. Then
place the whole unit in the hole and use the M8x90 bolt to ix it to the metal frame underneath.
Use the M8x30 to ixate it from the side, do not overtighten.
B
Nut
M8x90
Washer
Washer
M6 safety set screw

07
19-09-2022
CLEANING
Clean the laminate surface with warm water and a soft sponge.
NEVER use the abrasive “green” side of the sponge. Use an ordinary universal cleaner.
Diicult dirt must be removed with a nano sponge and water. Please take a closer
look at our website, or contact us for information.
Kigkurren 8A
Islands Brygge
DK2300 Copenhagen
out-sider.dk
[phone]