Outward Slippery Slide User manual

Slippery Slide
Assembly Instructions

Children must not use the product until properly installed.The product
must be assembled by an adult.
Please read these instructions carefully. The instructions are an
integral component of the product. Therefore, please store them and the
packaging carefully in case questions arise in the future. Always include
these instructions when handing on the product to a third party. This
product must be assembled by an adult. This product is not designed
for industrial use. The use of the product requires certain capabilities
and skills. Always adjust according to the age of the user and use for the
purpose it has been designed for.
• Observing the following statements and warnings reduce the
likelihood of serious or fatal injury.
• Always follow the safety warnings and use common sense when using
the product.
• To prevent serious injury, do not allow children to play on the product
until it is completely assembled and installed.
• Instruct children not to use the equipment in any manner other than
intended. Instruct children to dress appropriately. Loose fitting clothing is
potentially hazardous when using the product.
• Never slide head first down the slide.
• Changes to the original product must only be carried out according to
manufacturer specifications.
• Equipment may be slippery when wet. Do not allow children to use the
equipment when wet.
• Ensure a safe distance from other structures or obstructions of at least
6’ 5” feet and for a level, shock-absorbing underground (e.g. grass) free
from sharp or pointed objects, obstacles (e.g. clotheslines etc.), gradients,
steps, stairs or hard surfaces (e.g. concrete etc.).
• Adult supervision of children is required at all times when on or around
this product. Never leave children unattended. Parents should regularly
check openings and surfaces that may be hazardous.
• This product is designed for normal residential use only.
• This product is not designed for use in day care, nurseries or other public
places.
• This product is to be assembled by adults only in the manner described
within this owner’s manual.
• This product must be anchored. Anchors are included with the product.
Not suitable for children under 3 years.
Small parts. Choking hazard.
Warning!
Warnings
Warning!
Read Me

#x
1x
2x 2x 2x 1x 4 x
2x 2x 2x 1x
1x
Hardware and Parts
Slide
Handlebar Center Leg Support Footstep Small Bracket Anchor
Long Leg Short Leg Large Bracket Water
Adapter
QuantityPart Label Tools Hardware (Bolts, Screws, and Nuts)
3Support Plate
2
1x 1x
1x
5mm
Allen Key
Wrench Phillips
Screw
Driver
* Not Included
W P
K
1 4 6 8 10
5 7 9 11
#TH
1x
Water
Adapter
Seal
12
4 x
10 x
A
BSmall Bolt
Large Bolt
13 x
4 x
C
DGold Screw
Nut

1
Insert both ends of the
handlerbars (Part 1), into the
slide holes as shown below
(Part 2).
Insert the longer ended
handlebars into the two
holes closest to the top of
the slide.
Wiggle the shorter ends of
the handlebars into the two
remaining holes.
This step requires some
force.
Follow the steps shown in the pictures.
The product should initially only be screwed
finger-tight to ensure that it does not warp
and to facilitate the assembly. Only when all
parts are assembled, should they be firmly
tightened and checked.
Please take note of sharp-edged holes and
chips that under circumstances may occur
by the manufacture of this game device and
if necessary have these removed.These
products should be assembled by adults.
1. Do not install home playground equipment
over concrete, asphalt, packed earth, grass,
carpet, or any other hard surface. A fall on to
a hard surface can result in serious injury to
the user.
2. Do not place your product underneath
electrical lines. If you must ensure that there
is a minimum overhead clearance of 6’ 5” ft.
Assembly 11
2

2
Position the support bracket
(Part 3) under the slide as
shown in the image below.
Pair the bracket to both of
the handlebars so that the
eyelets are aligned to the
center eyelets of the
handlebars.
3
Note: The support
bracket is slopped
parallel to the slide.
It goes under the
slide.

2 Small Bolts
3
Insert two small bolts (B)
into the slide opening.
The bolts will go through the
slide eyelets, handlebars
(Part 1) and will screw into
the bracket.
Use the allen key (K) to
tighten the bolts. B
B
K
4
Insert both center leg
supports (Part 4) into the
shorter ends of the
handlebars (Part 1).
4 4
1
1

2 Small Bolts
2 Nuts
5
Insert two small bolts (B)
and nuts (C) into the slide
opening.
The bolts will go through the
slide eyelets, handlebars/
center leg support eyelets,
and screw them together
with the nuts (C).
Use the allen key (K) and the
wrench (W) to tighten the
bolts and nuts.
C
W K
B
C
4 Large Bolts
4 Nuts
6
Insert both footsteps
(Part 6) into each of the
long legs (Part 5).
Align both of the
footsteps as shown in
diagram 1. If aligned
properly, the
footsteps will lay flat
once they are inserted to
the handlebars
(Part 1).
The handlebar (Part 1),
top footstep (Part 6),
and long legs (Part 5) will
be screwed in together
as shown in diagram 2.
Use the allen key (K) and
the wrench (W) to tighten
the footsteps with the
bolts and nuts.
The footsteps are
installed incorrectly if
they are angled down
towards the ground.
A
W K
C
1
2
5
6
56
1

Note: Here is an example of how the handlebars, footsteps, and long legs are
attached to each other.
7
Insert both of the short legs
(Part 7) into the center leg
supports (Part 4).
4
7

8
Insert 2 small bolts (B) through the small bracket (Part 8) eyelets, center
leg support and short leg eyelets. Screw them all together with the nuts (C)
facing towards the footsteps.
8
C
8
B
B
2 Small Bolts
Small Bracket
2 Nuts
B
8
W K
C
C
9
Insert 4 small bolts (B) through the large bracket (Part 9) eyelets, center leg
support and the longest end of the handlebar eyelets. Screw all of the pieces
together with the nuts (C) provided. Make sure the nuts are facing inwards.
Use the allen key (K) and the wrench (W)
to tighten the bolts and nuts.
Use the allen key (K) and the wrench (W)
to tighten the bolts and nuts.
4 Small Bolts
2 Large Brackets
4 Nuts
B
9
W K
C
9
9
B
C
C
B

10
Use the anchors (Part 10) provided to secure the
slide to the grass before allowing your children to
play on the slide.
11
On the back of the slippery slide, you will find 4 connection points. This is
where you will connect the water adapter to the slide.
Phillips Screw Driver*
*Not Included
Water Adapter Seal
Water Adapter
4 Gold Screws
12
11
P
D

12b
Align the water adapter
(Part 11) and the gold
screws (D) to the 4
connection points on
the back of the slide
(Part 2).
12d
Insert water hose.
12a
Insert the water
adapter seal (Part
12) to the groove on
the back of the water
adapter (Part 11).
12c
Tighten
D
11
2
12
11

[email protected]
[phone]
Lets us know if you have questions or concerns: