Outward OUT117 User manual

472315_124142_IM.indd 1
30/10/2015 3:56 PM
It is very important that you read and understand the instructions before assembling and using the seesaw.
IMPORTANT
Read the following statements and warnings to avoid serious injury.
Warning.
- Max 50 kg.
- Only for domestic use.
- Indoor/Outdoor use.
- Maximum 2 users.
- Read the instructions.
- The seesaw shall be assembled by an adult in accordance with the
assembly instructions and then checked before the first use.
- Empty pockets and hands before rocking.
- Do not use when the seesaw is wet.
- Do not eat while rocking.
- Do not jump from the seesaw.
- Limit the time of continuous usage (take regular breaks).
- Do not use in strong wind conditions and secure the seesaw.
- Take off any jewellery.
Placement of the seesaw
Do not place the seesaw on a concrete floor or other hard surfaces. The
ideal placement is a level, stable surface like a lawn. There must be at
least 2 meters of space around the seesaw. Check that there are no wires,
tree branches, fences or other possible hazards above and around the
seesaw. The seesaw should not be placed near any pools, swings, slides,
climbing frames, trampolines or other obstructive installations. The seesaw
is not intended to be buried in the ground.
Weather conditions
The seesaw should not be used when wet. In winter conditions, please
disassemble the seesaw and store all parts inside. Always secure the
seesaw to the ground using Ground Stakes/Anchors (included).Do not use
in strong wind conditions.
How to use
Take it easy at first. Don’t try difficult moves.
Be sure to wear proper shoes, e.g. gym shoes, or be barefoot when rocking.
Never dismount by jumping off the seesaw. Always climb off.
Don’t use the seesaw under the influence of drugs or alcohol.
Always have someone else watching while you play. If you should injure
yourself you will have someone to assist you.
Care and maintenance
This seesaw was designed and manufactured with quality materials and
craftsmanship. If proper care and maintenance is provided, it will provide
all seesaws with years of exercise, fun, and enjoyment as well as reduce
the risk of injury. Please follow the guidelines listed below.
Instalments of additional accessories must be carried out as per
manufacturer’s instructions.
This seesaw is designed to withstand a certain amount of weight and use.
Please make sure that maximum two persons at any one time use the
seesaw. Users should either wear socks, gymnastics shoes, or be barefoot
when using the seesaw. Users should remove all sharp objects from their
person prior to using the seesaw. Regularly check that nuts and bolts are
securely tightened, since they may come loose over time. Check sharp
edges and all coverings and replace when required.
Always inspect the seesaw before each use for worn, abused or missing
parts. Anumber of conditions could arise that may increase your chances
of getting injured. Please be aware of:
•Bent or broken frame parts
•Bent or broken seats
•Damaged, missing, or insecurely attached nuts and bolts
•Protrusions of any types (especially sharp types) on the frame
Note. Sunlight, rain, snow and extreme temperatures reduce the strength
of these parts over time.
IF YOU FINDANY OF THE PREVIOUS CONDITIONS, ORANYTHING
ELSE THAT YOU FEEL COULD CAUSE HARM TO ANY USER, THE
SEESAW SHOULD BE DISASSEMBLED OR SECURED FROM USE
UNTIL THE CONDITION(S) HAS BEEN RESOLVED.
Do not modify the seesaw or any of its parts.
Keep this instruction manual.
OUT117 Twirl Seesaw
Instruction Manual

472315_124142_IM.indd 2
30/10/2015 3:56 PM
Assembly
Please read the assembly instructions fully before starting to assemble the seesaw.
Start first by checking that you have all the required parts. The reference number of each part will be used in the instructions to
guide you.
Seesaw Part List:
A Pivot tube (x1)
D Main crossbeam (x1)
B Shield tube (x1)
E End crossbeam (x2)
C Handle (x2)
F Legs (x3)
Bolt M6x35mm (x3) Bolt M8x60mm (x1) Plastic washer (x2)
Bolt M6x40mm (x4)
Bolt M6x45mm (x4)
Bolt M8x65mm (x4) Nut M6 (x11)
Nut M8 (x5)
Seat (x2) Anchor (x3)
Tools
10 20 30 40 50 60 70 80 90 100
mm

472315_124142_IM.indd 3
30/10/2015 3:56 PM
Step 1 Step 2
B
Nut M6
(x3)
Bolt
M8x60mm
(x1)
Plastic washer (x2)
D
Nut M8 (x1)
A
Bolt
M6x35mm
F F (x3)
F
Step 3
C
Bolt M6x40mm (x2)
Bolt M8x65mm (x2)
Seat
Assemble
2 sets
E
Nut M6 (x2)
Nut M8 (x2)
Step 4
Bolt M6x45mm (x4)
Step 3
assembled set
Nut M6 (x2)
Step 3
assembled set Nut M6 (x2)

Step 5
---- Anchor (x3)
Now go back and tighten all screws firmly and check the spring-Ioaded joints