Pan Acoustics TWM III User manual

Doc. No.:2017_V00238
DOCUMENTATION
Pan Acoustics GmbH │ Lindener Str. 15 │ 38300 Wolfenbüttel │ Germany │ Tel.: [phone] │ Email: [e-mail]
www.pan-acoustics.de
OPERATING MANUAL / ASSEMBLY MANUAL
for PB 04 | PB 08 | PB 16 | PB 24 | PB 32 | PB 40 | P 04-Pi | P 08-Pi | P 16-Pi
Wall Mount TWM III
Read the operating manual carefully prior to putting the device into operation.
The operating manual must be kept near the device.
V 1.0

© Pan Acoustics GmbH V 1.0 Page 2 of 7
Assembly Manual TWM III
1. Introduction
Thank you for choosing a product from Pan Acoustics.
With the purchase of this accessory for Pan Beam and Pan Speaker systems, you have acquired a product
for safe mounting of the PB 04 | PB 08 | PB 16 | PB 24 | PB 32 | PB 40 and P 04-Pi | P 08-Pi | P 16-Pi
arrays on walls.
Please read this operating manual carefully prior to startup in order to guarantee fault-free operation.
This symbol provides important instructions for proper handling of the
product. Failure to observe this instruction may lead to damage to the
product or malfunctions.
1.1. Symbols and explanation
This symbol indicates a hazard with a high level of risk. If this hazard is not
prevented, severe injuries or death may result.
This symbol indicates a hazard with a moderate level of risk. If this hazard is
not prevented, moderate to severe injuries or death may result.
This symbol indicates a hazard with a moderate level of risk. Failure to
observe this instruction may lead to minor injuries or property damage.
All specifi cations in this operating manual are based on the product features available at the time of
production and the safety rules applicable at that time.
This operating manual describes the setup, function and connection of the TWM III for Pan Beam and
Pan Speaker systems. It is geared towards systems technicians and persons assigned the task of
installing and operating the system.
Technical specifi cations such as dimensions, weight and properties do not represent guaranteed prop-
erties. Pan Acoustics reserves the right to make changes and modifi cations without prior notice within
the scope of statutory regulations and product improvements.
This operating manual and all additional information required for operation must be read prior to
use by all persons involved in commissioning. The operating manual and all additional information
required must be kept within reach, near the device.
German is the original language of all Pan Acoustics operating manuals.
All necessary information and documents can be obtained from the Pan Acoustics website,
www.pan-acoustics.de/en/manuals.html, or per email from [email protected].
1.2. General information and target group
2. Product description
With the TWM III speaker accessory, a PB 04 | PB 08 | PB 16 | PB 24 | PB 32 | PB 40 and
P 02-Pi | P 04-Pi | P 08-Pi | P 16-Pi array can be easily and safely mounted on walls. The mount is
attached to the wall by means of dowel joints (not included in scope of delivery).
The mount is designed for both indoor and outdoor use.
Depending upon the speaker length, several brackets may be necessary. The mount is always
to be installed at the midpoint of the speaker/speaker module (PB 08).

© Pan Acoustics GmbH V 1.0 Page 3 of 7
Assembly Manual TWM III
2.1. Scope of delivery
Screws and dowels for the attachment to the wall are not included in the scope of delivery. These
must be individually matched to the structure and material of the wall.
3. Safety instructions
The following safety regulations are to be read completely and diligently prior to installing the mount
and afterwards kept in a safe place near the device. Reading the instruction manual is no substitute
for knowing and following all valid local safety regulations and rules. Persons assigned to the assembly
of equipment must be properly trained and are required to work with proper personal protection
equipment. Furthermore, the assigned persons are responsible for, and are to guarantee, the safe
setup and use of the speaker.
• Power and signal lines must never be used for suspending, rigging or securing speakers.
• Only use the mount intended for mounting specifi ed products in order to guarantee safe operation
of the products.
The mount is to be carefully inspected upon receipt for shipping damage and completeness. In case
of damage, the forwarder and sender are to be notifi ed without delay.
Safety may be impaired if the product:
• shows signs of visible damage.
• has not been delivered completely.
• has been stored under adverse conditions for a prolonged period.
• has been improperly shipped (e.g. unsuitable packaging).
If the product shows signs of impairments that no longer guarantee safe operation, the article is to
be secured and labeled accordingly. It should also be ensured that no intentional or inadvertent use
by third parties is possible.
• When attaching the mount to a wall, check the weight capacity, rigidity and type of wall. In case
of a porous base surface, for instance, additional measures are to be taken by the assembler to
prevent the screw connection from breaking out of the wall.
• Only the original parts delivered by Pan Acoustics are allowed to be used for assembly.
The use of other parts, in particular parts from unknown or third-party manufacturers, is prohibited.
• Please undertake to ensure that all mounting and fastening materials conform to the relevant
safety guidelines and are suffi ciently dimensioned.
• Undertake to ensure that all connections are friction locking and form fi tting, and secured against
self-loosening.
Description Quantity
Slider 30 x 5 x 90mm 1
Threaded pin, M6 x 8mm socket bolt, A2, DIN 916 2
Mount (loudspeaker) 1
Allen screw M6 x 10mm, A2, DIN 7984 2
Wall mount 1
Axle element 1
Hexagon nut, M6, DIN 985 2
Hex bold, M6 x 35mm, DIN 933 2
Half bolt with allen, M8 x 16mm 10.9 vz, ISO 7380 2
Washer, M8 2
Cap 4
Product information for Pan Acoustics accessories 1

© Pan Acoustics GmbH V 1.0 Page 4 of 7
Assembly Manual TWM III
• The user is to observe existing safety requirements and regulations.
• The speaker accessory is not to be used for lifting, lowering or securing people or objects other
than the specifi ed speakers from the Pan Beam and Pan Speaker series.
• The TWM III is rated for the assembly of speaker systems weighing up to 11 kg.
• It is recommended to use an additional securing element to secure each suspended speaker
against falling.
• In general, a visual inspection of the speaker and the accessory is to be performed prior to
each use/assembly. If there are signs of wear, cracking or deformation, they are to be replaced
without delay. The visual inspection also includes checking the screw connections on load-
bearing parts of the speaker and accessory.
BA CD
HE G
F
4. Assembly and use instructions
4.1. Overview of assemblies
Description Drawing
Slider 30 x 5 x 90mm A
Threaded pin, M6 x 8mm socket bolt, A2, DIN 916 B
Bracket (loudspeaker) C
Screw, allen screw M6 x 10mm, A2, DIN 7984 D
Bracket (wall) E
Axle element F
Hexagon nut, M6, DIN 985 G
Hex bold, M6 x 35mm, DIN 933 H
Half bolt with allen, M8 x 16mm 10.9 vz, ISO 7380 I
Washer, M8 J
Cap K

© Pan Acoustics GmbH V 1.0 Page 5 of 7
Assembly Manual TWM III
4.2. Assembly
Insert the slot nut (A) into the
rear slot of the speaker through
the opening in the cover.
Pre-mount the 2 set screws (B)
into the middle threads of the
slot nuts. Position the slot nut
at the midpoint of the speaker
and tighten the set screws so
that the slot nut can no longer
move.
Screw bracket (speaker) (C)
onto the mounted slot nut (A)
using 2 screws (D).
Improperly selected fastening material for wall or ceiling assembly may cause the speaker to fall
down.
Prior to assembly, it is necessary to check the wall or ceiling material to which the speaker is to be
fastened. Be sure to provide suitable fastening material (dowels and matching screws) for assembly.
Model P 04
PB 04 P 08-Pi PB 08 P 16-Pi PB 16 PB 24 PB 32 PB 40
Brackets 11224 5
Number of brackets depending upon speaker module
Depending upon the speaker, additional brackets may be required, see table.
IJK

© Pan Acoustics GmbH V 1.0 Page 6 of 7
Assembly Manual TWM III
6. Transport and storage
The product is to be transported with care to prevent any damage that would impair its function.
The product is designed for both indoor and outdoor applications. Prolonged storage in liquids, e.g.
water, is to be avoided.
Install the pre-mounted mount
(loudspeaker) (C) into mount
(wall) (D).
Check all screw connections for fi rm fi t and friction locking. The individual assemblies are to be
checked to ensure that they are form fi tting, and screw connections are to be re-tightened where
appropriate.
5. Maintenance and care
The speaker accessory may show signs of wear over time, e.g. due to mechanical loads, corrosion or
improper handling. Therefore, for permanent installations, check the mount at regular intervals for
signs of wear and fi rm fi t.
When performing inspections, it is particularly important to watch out for deformations, cracks,
notches, damage on threads and corrosion. Mounting and fastening materials such as screws and
tensioning straps also need to be checked thoroughly for wear or deformation.
If the check reveals uncertainties or damaged parts, the speaker/mount may no longer be used. The
operator/user is required to be familiar with country-specifi c comprehensive testing regulations and
to apply them.
Fasten bracket (wall) (E) using
two screw fi xings suitable for
wall mounting.
Install the axle (F) with the
pre-mounted screw connection
(G+H) into holder (wall) (E).
Connect the Axle (F) with
screw (I) and washer (J) with
the mount (wall) (D) on top
and bottom.
Push the caps (K) onto the
screw connection.

© Pan Acoustics GmbH V 1.0 Page 7 of 7
Assembly Manual TWM III
7. Dimensions and weight
Weight without assembly material: 0.5 kg
8. Disposal
The product is to be disposed of according to existing national regulations.
Please undertake to ensure that the product cannot be re-used or used for any other purpose after
disposal.
9. Contact address
Pan Acoustics GmbH
Lindener Straße 15
38300 Wolfenbüttel
Germany
Tel: [phone]
Fax: [phone]
Email: [email protected]
27mm
53mm
44mm
19mm
26mm
81mm
92mm
109mm