Uplift Desk MON020 User manual

Bolt-through top
Wire clips
(qty 4)
13 mm Flat
wrench
Step 1.1 - Clamp
Rest the Bottom plate on the Base’s bolt. Next, t the Base around
the back edge of your desk, and using the 6.5 mm Allen wrench,
tighten the Long bolt & Bottom plate into place.
When placing the Bottom plate on the Base’s bolt, make sure the
edge farthest from the hole is facing the back of the Base and the
edge closest to the hole aligns with the front edge of the Bottom
clamp. If you’re attaching this to a UPLIFT V2 4-Leg Desk, this is
the only way it will t properly.
Note: If the Clamp does not t on your desk edge, you can in-
crease or decrease the space between the Clamp by removing
the bottom of the Clamp and the Bolt, and repositioning them.
Using the 4 mm Allen wrench, unscrew the two screws holding
the bottom of the Clamp (see g. 1).
For thinner desks (0.75’’ minimum), reassemble the Clamp as
shown in g. 2. For thicker desks (3.75’’ maximum), reassemble
the Clamp, as shown in g. 3.
Note: If you’re mounting this to an UPLIFT V2 4-Leg Desk, 2.5’’ will
be the maximum thickness that will work with the Clamp.
Once the Clamp is sized and attached to your desktop as de-
scribed above, continue on to Step 2.
min
thickness
0.75’’
max
thickness
3.75’’
g. 1 g. 2 g. 3
Base
Bottom plate
Parts for
Bolt-through assembly
VESA mount
Monitor screw
(qty 4)
Long bolts
(two sizes included:
50 mm & 70 mm)
Allen wrenches
(set of ve:
2 mm, 3 mm, 4 mm,
6 mm, and 6.5 mm)
Gas arm
Extension arm
Monitor joint
Step 1.2 - Bolt-through
To mount your monitor arm through a hole in your desktop, rst
measure the hole. It must be between a minimum of 0.4’’ and a
maximum of 3.15’’ in diameter.
Prepare the Base for the Bolt-through mount by rst loosen-
ing the screw under the Clamp with the 6 mm Allen wrench.
Note: screw may be tight. Once removed, separate the Clamp as-
sembly from the Base.
Place the Base onto the Bolt-through top, as shown. The Base’s
small peg should t into the small hole on the Bolt-through top.
Rotate until the large hole lines up with the notch at the front of
the Base.
Place assembly completely over the hole, and facing the front of
desk. Then, select a Long bolt: the 50 mm Bolt ts desks 0.6’’ to
1.38’’ thick, and the 70 mm Bolt ts desks 1.38’’ to 2.13’’ thick. Insert
the Long bolt through the Bottom plate.
Note: The Bottom plate must straddle the hole’s diameter. As
long as the hole isn’t larger than 3.15’’ than the Bottom plate will
work. Thread the bolt into the Base assembly by hand and tighten
using the 6 mm Allen wrench.
Note: There are two ways to attach to your desktop: Clamp and Bolt-through mount. Determine if you need to attach it
around the back side of your desk (follow Step 1.1) or through a hole from 0.4’’ to 3.15’’ in diameter (follow Step 1.2).
Package Contents
Range Single Monitor Arm
SKU: MON020
© UPLIFT Desk • 1-800-349-3839 • [email protected] • upliftdesk.com

Step 3
After all components from Step 2 are in place, you may choose
to tighten the set screws, which will lock all the components to-
gether, and prevent them from separating or drifting on their own.
They are located at each insertion point, and marked in this in-
struction book with a “ ”.
• At the top of the Base’s neck, where the Gas arm is inserted.
• At the top of the Gas arm, where the Extension arm is inserted.
• And at the end of the Extension arm, where the Monitor joint is
inserted.
Use the 3 mm Allen wrench provided. Make sure not to overtight-
en the set screws.
*
*
**
Step 2
With the Base attached to the desk, it’s time to assemble the re-
mainder of the arm by inserting the Gas arm, which ships with a
pre-installed stopping pin at the bottom near the post (see g.
4). This pin limits the arm’s rotation to 180 degrees. If you want
a full 360 degrees of rotation, remove this pin with the 2 mm
Allen wrench. Then insert the Gas arm into the Base.
Insert the Extension arm into the Gas arm, and complete this
part of the assembly by inserting the Monitor joint into the Ex-
tension Arm.
Step 4
Place your monitor face down on a at surface, making sure
not to scratch the screen. Next, attach the VESA mount to
the back of your monitor using a Phillips-head screwdriver
and four Monitor screws. The mount is designed to t the in-
dustry standard VESA 75 mm & 100 mm hole patterns. Make
sure the VESA mount is securely fastened to your monitor
before moving on to the next step.
Note: make sure the tab on the VESA mount is facing the top
of your monitor.
© UPLIFT Desk • 1-800-349-3839 • [email protected] • upliftdesk.com
g. 4

© UPLIFT Desk • 1-800-349-3839 • [email protected] • upliftdesk.com
CAUTION: Read all instructions before assembly. Failure to assemble or operate properly may
result in damage or personal injury. Retain manual for future reference.
CAUTIONS & WARNINGS
!
!
Step 5
Now, insert your monitor and VESA mount assembly into the
Monitor joint mount, holding it rmly as you insert it until you
feel it click into place.
The Range Gas arm tension is factory set for the heaviest
monitor weight. To adjust the tension if the monitor is too
light for the maximum setting, hold the Gas arm horizontal
and, using 6 mm Allen wrench, turn the set screw located at
the lower section of the arm toward the “-”.
Keep adjusting the tension until the monitor arm holds its
position when you let it go.
Step 6
Insert the Wire clips into the underside of the Extension arm
and the Gas arm, and run your cables through them, making
sure the cables are not pulled too tight. There should be some
slack in the cables to allow the arm to move freely without be-
ing restricted.
Monitor Ergonomics
Screen Distance: Set your screen about an arm’s length (ap-
proximately 18’’ - 28’’) from your eyes. If print is too hard to
read, it is better to make the print larger on your screen than it
is to move the screen closer to your eyes.
Monitor Height: The top of the monitor should be at or just
below eye level.
Monitor Tilt: The monitor should be
tilted slightly up so it’s easier to see
the screen when the top of the mon-
itor is level with your eyes. If the joint
holding the monitor does not move,
loosen the hex bolt on the Monitor
joint slightly with the 13 mm Flat
wrench.

512-614-3152
800-349-3839
[email protected]
upliftdesk.com
Work Better. Live Healthier
Copyright Notice: This guide is a component of this UPLIFT Desk product. This guide is a part of the scope of delivery, even if the item is resold. This
guide is also available on the UPLIFT Desk website: upliftdesk.com. Excerpts or copies may not be forwarded to third parties or used in any other
published form without the prior written consent of UPLIFT Desk. These instructions are subject to United States copyright law.
©
SAVE THESE INSTRUCTIONS
Study this manual carefully. If this product is sold, please provide this
manual to the buyer, installers, or support personnel operating the product.
®
AI-MON020-1.3