Panasonic Viera TC-L47ET5 Manual

Page 1 of 2 2/6/2013
© 2013 Global VR, Inc. All Rights Reserved. GLOBAL VR and the GLOBAL VR logo are registered trademarks of Global VR, Inc. All other
trademarks are the properties of their respective owners.
Panasonic 3D TV Setup
Document Part #: 040-0256-01
Note: These instructions are specific to Panasonic TV Model No. TC-L47ET5.
If you are experiencing a problem with the TV, GLOBAL VR recommends resetting the TV to
factory defaults and then re-entering all of the settings as described in this section.
Use the remote control and follow the steps below. General instructions for navigating the menus
with the remote control are as follows:
−Use the UV buttons on the remote control to highlight an item in a menu.
−Use the YZbuttons to change the setting for the highlighted item.
−Press the OK button to open a submenu or save a setting.
−Press the Return button to exit from a menu or submenu.
Note: Highlighted items are Yellow on the menu screens.
1. Before setting up the monitor, the System Computer must be in 1080p and 3D Mode. Press
the Test/Back button on the Operator Button Panel inside the coin door and confirm or set
the following in the Operator Menu:
−In Machine Settings: Settings set 3D Display to Enable
−In Diagnostics: Monitor Resolution set resolution to 1920 x 1080
2. Press the MENU button on the remote control to open the Main menu.
3. Highlight Setup in the Main menu and press OK to open the Setup menu.
4. Use the Vbutton to scroll down to Reset to defaults (it is off-screen when you open the
menu) and press OK. You will be prompted to create a password. (This is a temporary
password that will not be saved by the TV.) Enter a simple 4-digit password (such as 1-1-
1-1) with the remote control keys and press OK. Enter the password again in the
confirmation screen and press OK.
5. When you see the Reset to Defaults prompt, highlight Yes and press OK.

Panasonic 3D TV Setup
Page 2 of 2
040-0256-01 2/6/2013 © 2013 Global VR, Inc.
6. After you reset the defaults, the following Setup Screens will appear. On each screen,
select the setting described below and press OK to go to the next screen. To go back a
screen, press the Return button.
Screen Setting
Select your language. English
Select Country where this TV is being used. U.S.A. (Set this even if located elsewhere.)
Select your viewing environment. Home Use
Do you use a cable, satellite, or fiber optic
box with this TV? Yes
Which wiring method is used to connect your
box to the TV? AV IN
What is connected to HDMI 1? Leave all entries on this screen blank. Use the V
key to highlight Next and press OK
Network Settings Set Later
Set clock Use the Vkey to highlight Next and press OK.
(The game does not use TV date and time settings.)
7. When you see the Setup is complete message, press OK to exit.
8. Press the 3D button on the remote control to put the TV in 3D mode. Read the 3D warning
message. Where it says, "Would you like to display this message again later?" Highlight
No and press OK.
9. Press the MENU button on the remote control to open the Main menu again.
Note: The picture must be set to 3D before doing step 10.
10. Highlight Picture in the Main menu and press OK. Use the Vbutton to scroll down to
Aspect adjustments (it is off-screen when you open the menu) and press OK. Do the
following steps in the Aspect Adjustments menu:
−Use the YZbuttons to set Screen Format to FULL.
−Use the YZbuttons to set HD Size to Size 2 (Note: The TV will hide the menu when you
highlight this setting so you can see how your selection looks. If you do not set Size 2 the
Insert Coins message will be off-screen).
−Press Return to go back to the Picture menu.
11. Highlight Picture mode in the Picture menu and use the YZbuttons to set it to Vivid.
12. Press Return to go back to the Main menu.
13. Highlight Setup in the Main menu and press OK to open the Setup menu.
14. Highlight 3D Settings in the Setup menu and press OK. Do the following steps in the 3D
Settings menu:
−Use the YZbuttons to set Auto Detect 3D to Auto 2.
−Use the YZbuttons to set 3D Signal Notification to Off.
−Press Return to go back to the Setup menu.