Panasonic Genius NN-SD697S User manual

© 2007 Panasonic Home Appliances Microwave
Oven (Shanghai) Co., Ltd. All rights reserved.
Unauthorized copying and distribution is a violation
of law.
NN-SD697S
NN-SD677S
NN-SD667S
NN-SN677S
NN-SN667
NN-SN657S
NN-SA647
NN-ST677S
NN-ST657W
APH(USA)
CPH(CANADA)
RPH(MEXICO/LATIN AMERICAN)
Microwave Oven
Please file and use this specified manual together with the service manual for Model NN-T695 (ORDER NO.
PHAMOS0501001C7).
ORDER NO.PHAMOS0701001A7
E1

2
NN-SD697S / NN-SD677S / NN-SD667S / NN-SN677S / NN-SN667 / NN-SN657S / NN-SA647 / NN-ST677S / NN-ST657W

3
NN-SD697S / NN-SD677S / NN-SD667S / NN-SN677S / NN-SN667 / NN-SN657S / NN-SA647 / NN-ST677S / NN-ST657W

1 SCHEMATIC DIAGRAM 5
1.1. APH 5
1.2. CPH 6
1.3. RPH/RTH 7
2 CAUTIONS TO BE OBSERVED WHEN TROUBLESHOOTING
8
2.1. Check the grounding 8
2.2. Inverter warnings 8
2.3. Part replacement. 9
2.4. When the 20A fuse is blown due to the operation of the
short switch: 9
2.5. Avoid inserting nails, wire etc. through any holes in the
unit during operation. 9
2.6. Confirm after repair 9
2.7. Sharp edges 9
3 MEASUREMENTS AND ADJUSTMENTS 10
3.1. Adjustment of primary latch switch, secondary latch switch
and short switch. 10
3.2. Measurement of microwave output 10
4 PROCEDURE FOR MEASURING MICROWAVE ENERGY
LEAKAGE 11
4.1. Equipment 11
4.2. Procedure for measuring radiation leakage 11
4.3. Record keeping and notification after measurement 11
4.4. At least once a year, have the radiation monitor checked
for calibration by its manufacturer. 11
5 SIMPLE WAY OF H.V. INVERTER/MAGNETRON
TROUBLESHOOTING 12
6 H.V.INVERTER BOARD MAIN PARTS LIST (F606Y8M00AP)
12
7 EXPLODED VIEW AND PARTS LIST 13
7.1. EXPLODED VIEW 13
7.2. PARTS LIST 14
7.3. WIRING MATERIALS 15
7.4. DOOR ASSEMBLY 16
7.5. ESCUTCHEON BASE ASSEMBLY 17
7.6. PACKING AND ACCESSORIES 21
8 DIGITAL PROGRAMMER CIRCUIT 22
8.1. NN-SD697S APH 22
8.2. NN-SD677S CPH, SD667S APH 24
8.3. NN-SN677S APH 26
8.4. NN-SN667B/W/BB/WB/M B APH, SN667B/W CPH 28
8.5. NN-SN657S APH, ST677S RPH/RTH, ST657W RPH/RTH
30
8.6. NN-SA647B/W APH 32
8.7. PARTS LIST 34
CONTENTS
Page Page
4
NN-SD697S / NN-SD677S / NN-SD667S / NN-SN677S / NN-SN667 / NN-SN657S / NN-SA647 / NN-ST677S / NN-ST657W

1 SCHEMATIC DIAGRAM
1.1. APH
5
NN-SD697S / NN-SD677S / NN-SD667S / NN-SN677S / NN-SN667 / NN-SN657S / NN-SA647 / NN-ST677S / NN-ST657W

1.2. CPH
6
NN-SD697S / NN-SD677S / NN-SD667S / NN-SN677S / NN-SN667 / NN-SN657S / NN-SA647 / NN-ST677S / NN-ST657W

1.3. RPH/RTH
7
NN-SD697S / NN-SD677S / NN-SD667S / NN-SN677S / NN-SN667 / NN-SN657S / NN-SA647 / NN-ST677S / NN-ST657W

Unlike many other appliances, the microwave oven is a high
voltage, high current device. It is free from danger in ordinary
use, though extreme care should be taken during repair.
Caution
Servicemen should remove their watches whenever
working close to or replacing the magnetron.
2.1. Check the grounding
Do not operate on a two wire extension cord. The microwave
oven is designed to be grounded when used. It is imperative,
therefore, to ensure the appliance is properly grounded before
beginning repair work.
2.2. Inverter warnings
DANGER, HIGH VOLTAGE AND HIGHTEMPERATURE
(HOT/LIVE) OF THE INVERTERPOWER SUPPLY (U)
The High Voltage Inverter Power Supply handles very high
voltage and current for the magnetron tube. Though it is
free from danger in ordinary use, extreme care should be
taken during repair.
The aluminum heat sink is also energized with high voltage
(HOT), do not touch when the AC input terminals are
energized. The power device Collector is directly connected
to the aluminum heat sink.
The aluminum heat sink may be HOT due to heat energy,
therefore, extreme care should be taken during servicing.
H.V. Inverter warning
WARNING FOR INVERTER POWER SUPPLY (U)
GROUNDING
Check the High Voltage Inverter Power Supply circuit
grounding. The high voltage inverter power supply circuit
board must have a proper chassis ground. The inverter
grounding bracket must be connected to the chassis. If the
inverter board is not grounded it will expose the user to very
high voltages and cause extreme DANGER! Be sure that
the inverter circuit is properly grounded via the inverter
grounding bracket.
Grounding of the inverter circuit board
WARNING! DISCHARGE THE HIGH VOLATGE
CAPACITORS
For about 30 seconds after the oven is turned off, an
electric charge remains in the high voltage capacitors in the
Inverter Power Supply circuit board.
When replacing or checking parts, remove the power plug
from the outlet and short the inverter output terminal of the
magnetron filament terminals to the chassis ground with an
insulated handle screwdriver to discharge. Please be sure
to touch the chassis ground side first and then short to the
output terminals.
2 CAUTIONS TO BE OBSERVED WHEN
TROUBLESHOOTING
8
NN-SD697S / NN-SD677S / NN-SD667S / NN-SN677S / NN-SN667 / NN-SN657S / NN-SA647 / NN-ST677S / NN-ST657W

Discharging the high voltage capacitors
WARNING
There is high voltage present with high current capabilities
in the circuits of the primary and secondary windings, choke
coil and heat sinkof the inverter. It is extremely dangerous
to work on or near these circuits with the oven energized.
DO NOT measure the voltage in the high voltage circuit
including the filament voltage of the magnetron.
WARNING
Never touch any circuit wiring with your hand or with an
insulated tool during operation.
2.3. Part replacement.
When any part or component is to be replaced, always ensure
that the power cord is removed from the wall outlet.
2.4. When the 20A fuse is blown
due to the operation of the
short switch:
WARNING
When the 20A 120V fuse is blown due to the operation of
the interlock monitor switch, replace all of the components
(primary latch switch, short switch and power relay B
(RY1)).
1. This is mandatory. Refer to “adjustments and
measurements” for the location of these switches.
2. When replacing the fuse, confirm that it has the
appropriate rating for these models.
3. When replacing faulty switches, be sure the mounting
tabs are not bent, broken or deficient in their ability to
hold the switches.
2.5. Avoid inserting nails, wire etc.
through any holes in the unit
during operation.
Never insert a wire, nail or any other metal object through the
lamp holes on the cavity or any holes or gaps, because such
objects may work as an antennaand cause microwave leakage.
2.6. Confirm after repair
1. After repair or replacement of parts, make sure that the
screws of the oven, etc. are neither loosen or missing.
Microwave might leak if screws are not properly tightened.
2. Make sure that all electrical connections are tight before
inserting the plug into the wall outlet.
3. Check for microwave energy leakage. (Refer to procedure
for measuring microwave energy leakage).
CAUTION MICROWAVE RADIATION
USE CAUTION NOT TO BECOME EXPOSED TO
RADIATION FROM THE MICROWAVE MAGNETRON OR
OTHER PARTS CONDUCTING MICROWAVE ENERGY.
IMPORTANT NOTICE
The following components have potentials above 2000V
while the appliance is operated.
• ••
•
Magnetron
• ••
•
High voltage transformer (Located on inverter (U))
• ••
•
High voltage diodes (Located on inverter (U))
• ••
•
High voltage capacitors (Located on inverter (U))
Pay special attention to these areas.
When the appliance is operated with the door hinges or
magnetron installed incorrectly, the microwave leakage can
exceed more than 5mW/cm2. After repair or exchange, it is
very important to check if the magnetron and the door
hinges are correctly installed.
2.7. Sharp edges
Caution
Please use caution when unpacking, installing or moving
the unit, as some exposed edges may be sharp to the touch
and cause injury if not handled with care.
9
NN-SD697S / NN-SD677S / NN-SD667S / NN-SN677S / NN-SN667 / NN-SN657S / NN-SA647 / NN-ST677S / NN-ST657W

3.1. Adjustment of primary latch
switch, secondary latch switch
and short switch.
1. Mount the Primary latch switch, the Secondary latch switch
and the Short switch to the door hook assembly as shown
in ILL.
NOTE:
No specific individual adjustments during
installation of the Primary latch switch, Secondary
latch switch or Short switch to the door hook are
required.
2. When mounting the door hook assembly to the oven
assembly, adjust the door hook assembly by moving it in
the direction of the arrows in the illustration so that the oven
door will not have any play in it. Check for play in the door
by pulling the door assembly. Make sure that the latch keys
move smoothly after adjustment is completed. Completely
tighten the screws holding the door hook assembly to the
oven assembly.
3. Reconnect the short switch and check the continuity of the
monitor circuit and all latch switches again by following the
component test procedures.
3.2. Measurement of microwave
output
The output power of the magnetron can be determined by
performing IEC standard test procedures. However,due to the
complexity of IEC test procedures, it is recommended to test
the magnetron using the simple method outlined below.
Necessary Equipment:
*1 liter beaker *Glass thermometer
*Wrist watch or stopwatch
NOTE:
Check the line voltage under load.Low voltage will
lower the magnetron output. Take the temperature
readings and heating time as accurately as possible.
1. Fill the beaker with exactly one liter of tap water.Stir the
water using the thermometer and record the water’s
temperature. (recorded as T1).
2. Place the beaker on the center of glass tray.
Set the oven for High power and heat it for exactly one
minute.
3. Stir the water again and read the temperature of the water.
(recorded as T2).
4. The normal temperature rise at High power level for each
model is as shown in table.
TABLE (1L-1min.test)
RATED OUTPUT TEMPERATURE RISE
1200W Min. 18.5°F(10.3°C)
1300W Min. 19.8°F(11.1°C)
3 MEASUREMENTS AND ADJUSTMENTS
10
NN-SD697S / NN-SD677S / NN-SD667S / NN-SN677S / NN-SN667 / NN-SN657S / NN-SA647 / NN-ST677S / NN-ST657W

NOTE:
The U.S. Government standard is 5 mW/cm2while in the
customer’s home. 2mW/cm2stated here is our own
voluntary standard. (1mW/cm2for Canada)
4.1. Equipment
• ••
•
Electromagnatic radiation monitor
• ••
•
Glass thermometer 212°F or 100°C
• ••
•
600cc glass beaker
4.2. Procedure for measuring
radiation leakage
Note before measuring.
• ••
•
Do not exceed meter full scale deflection. Leakage monitor
should initially be set to the highest scale.
• ••
•
To prevent false readings the test probe should be held by
the grip portion of the handle only and moved along the
shaded area in Figure no faster than 1 inch/sec
(2.5cm/sec).
• ••
•
Leakage with the outer panel removed ...... less than
5mW/cm2.
• ••
•
Leakage for a fully assembled oven with door normally
closed ...... less than 2mW/cm 2(1mW/cm 2for Canada).
• ••
•
Leakage for a fully assembled oven [Before the latch switch
(primary) is interrupted] while pulling the door ...... less than
2mW/cm 2.
1. Pour 275 ± 15cc (9ozss± 1/2oz) of 20°C ± 5°C (68° ± 9°F)
water in a beaker which is graduated to 600cc, and place in
the center of the oven.
2. Set the radiation monitor to 2450MHz and use it following
the manufacturer´s recommended test procedure to assure
correct results.
3. When measuring the leakage, always use the 2 inch (5cm)
spacer supplied with the probe.
4. Tap the start pad or set the timer and with the magnetron
oscillating, measure the leakage by holding the probe
perpendicular to the surface being measured.
4.2.1. Measurement with the outer panel
removed.
Whenever you replace the magnetron, measure for radiation
leakage before the outer panel is installed and after all
necessary components are replaced or adjusted. Special care
should be taken in measuring around the magnetron.
4.2.2. Measurements with a fully
assembled oven.
After all components, including outer panel are fully assembled,
measure for radiation leakage around the door periphery, the
door viewing window, the exhaust opening, control panel and
air inlet openings.
4.3. Record keeping and
notification after measurement
• ••
•
After any adjustment or repair to a microwave oven, a
leakage reading must be taken. Record this leakage
reading on the repair ticket even if it is zero.
A copy of this repair ticket and the microwave leakage
reading should be kept by repair facility.
• ••
•
Should the radiation leakage be more than 2 mW/cm 2
(1mW/cm for Canada) after determining that all parts are in
good condition, functioning properly, and genuine
replacement parts as listed in this manual have been used,
immediately notify PSTC, PSC or PCI.
4.4. At least once a year, have the
radiation monitor checked for
calibration by its
manufacturer.
4 PROCEDURE FOR MEASURING MICROWAVE ENERGY
LEAKAGE
11
NN-SD697S / NN-SD677S / NN-SD667S / NN-SN677S / NN-SN667 / NN-SN657S / NN-SA647 / NN-ST677S / NN-ST657W

5 SIMPLE WAY OF H.V. INVERTER/MAGNETRON
TROUBLESHOOTING
Purpose:
Simple way (3/37 seconds rule) of identifying whether it’s Magnetron, Inverter, or others.
Set-up:
The unit under question is connected through the Ammeter as shown below.
Procedure:
Follow the matrix table below to identify the problem source.
Note:
Do not replace both Inverter board and Magnetron simultaneously and automatically without going through this
procedure.
Power will: Ammeter reading is: To do: Remedy:
Shut off in 37 seconds
after “Start”.
1. Between 0.5A and 1.0A. Check and repair open magnetron circuit Open magnetron wiring between Inverter
and magnetron terminal.
2. Between 1.0A and 2.0A. Check continuity of D702 in Inverter PCB.
1. D702 shorted Replace H.V.Inverter(F606Y8M00AP)
2. D702 is OK Replace magnetron
Shut off in 3 seconds
after “Start”
1. Less than 0.5A Check open circuit: Latch Switch, DPC,
Power Relay and CN701
Replace defective component(s), or
correct switch, cables and connectors.
6 H.V.INVERTER BOARD MAIN PARTS LIST
(F606Y8M00AP)
Ref. No. Part No. Part Name & Description Pcs/Set Remarks
DB701 B0FBBS000001 BRIDGE DIODE 120A, 600V
L701 F50206G00AP CHOKE COIL 1
Q701 B1JAGV000015 TRANSISTOR SI 11000V
T701 A609A8M00AP H.V. TRANSFORMER 1(INCLUDING D701,D702,C706,C707)
C701 ECWF5284N300 CAPACITOR 10.28µF/500V
C702 ECWF2455N644 CAPACITOR 14.5µF/250V
12
NN-SD697S / NN-SD677S / NN-SD667S / NN-SN677S / NN-SN667 / NN-SN657S / NN-SA647 / NN-ST677S / NN-ST657W

7 EXPLODED VIEW AND PARTS LIST
7.1. EXPLODED VIEW
13
NN-SD697S / NN-SD677S / NN-SD667S / NN-SN677S / NN-SN667 / NN-SN657S / NN-SA647 / NN-ST677S / NN-ST657W

7.2. PARTS LIST
NOTE:
1. When ordering replacement part(s), please use part number(s) shown in this part list.
Do not use description of the part.
2. Important safety notice:
Components identified by mark have special characteristics important for safety.
When replacing any of these components, use only manufacture’s specified parts.
Ref. No. Part No. Part Name & Description Pcs/Set Remarks
1F00064W70AP CAUTION LABEL 1SD697S APH,SD667S APH,SN677S APH,SN657S APH
1F00069660AP CAUTION LABEL 1SN667 APH,SA647B/W APH,ST677S RPH/RTH,
ST657W RPH/RTH
1F00067600CP CAUTION LABEL 1CPH
2F00078M60BAP NAME PLATE 1SN667B/BB APH
2F00078M60HAP NAME PLATE 1SN667W/WB APH
2F00078M60SAP NAME PLATE 1SN667MB APH
2F00078M90BAP NAME PLATE 1SA646B APH
2F00078M90HAP NAME PLATE 1SA646W APH
2F00078R30HRP NAME PLATE 1ST657W RPH
2F00078R40HRP NAME PLATE 1ST657W RTH
3F00338F00AP FUSE LABEL 1APH,CPH
3F00338F00RP FUSE LABEL 1RPH,RTH
4F10016K10APG BASE 1
5F10084T00AP RUBBER FOOT 4
6F110D5Y00SAP CABINET BODY(U) 1SD677S CPH
6F110D5Y30SAP CABINET BODY(U) 1SD697S APH,SD667S APH,SN677S APH,
SN657S APH,ST677S RPH/RTH
6F110D5Y60SAP CABINET BODY(U) 1SN667MB APH
6F110D5Y30BAP CABINET BODY(U) 1SN667B/BB APH,SN667B CPH,SA647B APH
6F110D5Y30HAP CABINET BODY(U) 1SN667W/WB APH,SN667W CPH,ST657W RPH/RTH
6F110D5Y30HCP CABINET BODY(U) 1SA647W APH
7F200A8F00AP OVEN(U) 1EXCEPT SA647B/W APH,
ST677S RPH/RTH & ST657W RTH/RPH
7F200A8F40AP OVEN(U) 1SA647B/W APH,ST677S RPH/RTH,ST657W RTH/RPH
8F20555L00AP COVER 1
9F21315Y00AP PULLY SHAFT 1
10 F2177-F80 WASHER 1
11 F290D9330AP ROLLER RING(U) 1
12 F30206G30AP DOOR HOOK 1EXCEPT SA647B/W APH
12 F30206K50AP DOOR HOOK 1SA647B/W APH
13 F3097-5L00 LATCH SPRING 1SA647B/W APH
14 F31366G30AP HOOK LEVER A 1EXCEPT SA647B/W APH
14 F31366K50AP HOOK LEVER A 1SA647B/W APH
15 F31376G30AP HOOK LEVER B 1EXCEPT SA647B/W APH
15 F31376K50AP HOOK LEVER B 1SA647B/W APH
16 F31386G30AP HOOK LEVER C 1EXCEPT SA647B/W APH
16 F31386K50AP HOOK LEVER C 1SA647B/W APH
17 F400A8F00AP FAN MOTOR 1AC120V,SINGLE PHASE,60Hz
18 F40084T00AP FAN BLADE 1
19 F40257D00APG AIR GUIDE A 1
20 F41445Y00AP ORIFICE 1
21 A707S4T00AP STEAM SENSOR 1EXCEPT SA647B/W APH,
ST677S RPH/RTH & ST657W RPH/RTH
22 F64508660AP SENSOR COVER B 1EXCEPT SA647B/W APH,
ST677S RPH/RTH & ST657W RPH/RTH
24 F65434W00AP SENSOR COVER C 1EXCEPT SA647B/W APH,
ST677S RPH/RTH & ST657W RPH/RTH
25 F612E5U40AP INCANDESCENT LAMP (U) 1
26 J61415G10XN MICRO SWITCH 1(PRIMARY LATCH SWITCH) (V-15G-3C25)
27 J61414T00AP MICRO SWITCH 1(SECONDARY LATCH SWITCH) (D3V-16G-3C25)
28 F61456N60AP THERMAL CUTOUT 1
30 F61785U30XN MICRO SWITCH 1(SHORT SWITCH) (D3V-1G-2C25)
31 F606Y8M00AP H.V.INVERTER (U) 1
32 2M261-M32KLP MAGNETRON 1APH,RPH,RTH
32 2M261-M32JP MAGNETRON 1CPH
14
NN-SD697S / NN-SD677S / NN-SD667S / NN-SN677S / NN-SN667 / NN-SN657S / NN-SA647 / NN-ST677S / NN-ST657W

Ref. No. Part No. Part Name & Description Pcs/Set Remarks
33 F62308F00AP FUSE 1CPH
33 F62308F20AP FUSE 1APH,RPH,RTH
34 F62315G10XN FUSE HOLDER 1RPH,RTH
35 F66626K50AP GROUNDING PLATE 1
36 F63265G60AP TURNTABLE MOTOR 1
37 F900C4T60CP AC CORD W/PLUG 1SD697S APH,SD667S APH,SN677S APH,SN657S APH
37 F900C4T00AP AC CORD W/PLUG 1SN667 APH,SA647B/W APH,
ST677S RPH/RTH,ST657W RPH/RTH
37 F900C5Y30CP AC CORD W/PLUG 1CPH
38 F692Y8F00APX NOISE FILTER (U) 1APH,CPH
39 XTWFA4+12T SCREW 4FOR MAGNETRON
40 XTTFA4+6BN SCREW 1FOR COVER
42 XTCAFA4+12AFM SCREW 1FOR CABINET BODY SIDE (SD677S CPH)
42 XTCAFA4+12AFS SCREW 1FOR CABINET BODY SIDE (SD697S APH,SD667S APH,
SN677S APH, SN667MB APH,SN657S APH,
ST677S RPH/RTH)
42 XTCAFA4+12AFK SCREW 1FOR CABINET BODY SIDE
(SN667B/BB APH,SN667B CPH, SA647B APH)
42 XTCAFA4+12AFW SCREW 1FOR CABINET BODY SIDE (SN667W/WB APH,SN667W CPH,
SA647W APH, ST657W RPH/RTH)
43 XTTBFE4T12A0 SCREW 4FOR CABINET BODY
45 F65856K50AP INVERTER BRACKET 1
46 F03346K10AP MENU LABEL 1SD697S APH,SD667S APH,SN677S APH
46 F03346K10CP MENU LABEL 1SD677S CPH
46 F03347D60AP MENU LABEL 1SN667B/W/BB/WB/MB APH
46 F03347D60CP MENU LABEL 1SN667B/W CPH
46 F03345Y30AP MENU LABEL 1SN657S APH
46 F03347D80AP MENU LABEL 1SA647B/W APH
46 F03347G50RP MENU LABEL 1ST677S RPH/RTH,ST657W RPH/RTH
47 F02445Y00AP CAUTION LABEL 1SD677S CPH
48 F40264T60APG AIR GUIDE B 1
49 F04467D00AP FUNCTION LABEL 1SD667S APH
49 F04467D00CP FUNCTION LABEL 1SD677S CPH
50 F00067C50AP CAUTION LABEL 1APH,RPH,RTH
50 F00067C50CP CAUTION LABEL 1CPH
51 F00066G00RP CAUTION LABEL 1ST677S RPH/RTH
7.3. WIRING MATERIALS
Ref. No. Part No. Part Name & Description Pcs/Set Remarks
W1 F030A7D10AP LEAD WIRE HARNESS 1APH
W1 F030A7D00CP LEAD WIRE HARNESS 1CPH
W1 F030A7D00RP LEAD WIRE HARNESS 1RPH,RTH
W2 F030E5L00AP H.V.LEAD WIRE 1APH,RPH,RTH
W2 F030E4T00CP H.V.LEAD WIRE 1CPH
W3 F03537D00AP LEAD WIRE HARNESS U 1(INCLUDING THERMISTOR)
15
NN-SD697S / NN-SD677S / NN-SD667S / NN-SN677S / NN-SN667 / NN-SN657S / NN-SA647 / NN-ST677S / NN-ST657W

7.4. DOOR ASSEMBLY
Ref. No. Part No. Part Name & Description Pcs/Set Remarks
D1 F30186P40AG DOOR KEY A 1EXCEPT SA647B/W APH
D1 F30184Y30XN DOOR KEY A 1SA647B/W APH
D2 F301A8M00SAP DOOR A (U) 1SD697S APH,SN657S APH,ST677S RPH/RTH
D2 F301A8F60SQP DOOR A (U) 1SD677S CPH
D2 F301A8F00SCP DOOR A (U) 1SD667S APH
D2 F301A8M40SAP DOOR A (U) 1SN677S APH
D2 F302A8M60BAP DOOR A (U) 1SN667B/BB APH,SN667B CPH
D2 F302A8M60HAP DOOR A (U) 1SN667W/WB APH,SN667W CPH,ST657W RPH/RTH
D2 F302A8M60SAP DOOR A (U) 1SN667MB APH
D2 F302A8L80BCP DOOR A (U) 1SA647B APH
D2 F302A8F50HCP DOOR A (U) 1SA647W APH
D3 F302K5L00AP DOOR E (U) 1
D4 F30215G10XN DOOR KEY SPRING 1
D5 F30854T00AP DOOR C 1
D6 F31454T00AP DOOR SCREEN A 1
D8 F02459660AP DHHS LABEL 1SD697S APH,SD667S APH,SN677S APH,
SN657S APH, ST677S RPH/RTH
D8 F04114180CP HC LABEL 1SD677S CPH
16
NN-SD697S / NN-SD677S / NN-SD667S / NN-SN677S / NN-SN667 / NN-SN657S / NN-SA647 / NN-ST677S / NN-ST657W

7.5. ESCUTCHEON BASE ASSEMBLY
7.5.1. NN-SD697S APH, SD677S CPH, SD667S APH
Ref. No. Part No. Part Name & Description Pcs/Set Remarks
E1 F603L8M00AP D.P.CIRCUIT (AU) 1SD697S APH
E1 F603L8M10CP D.P.CIRCUIT (AU) 1SD677S CPH
E1 F603L8L60AP D.P.CIRCUIT (AU) 1SD667S APH
E2 F603Y8M00AP D.P.CIRCUIT (DU) 1SD697S APH
E2 F603Y7D00CP D.P.CIRCUIT (DU) 1SD677S CPH
E2 F603Y7D00AP D.P.CIRCUIT (DU) 1SD667S APH
E3 F800L8M00SAP ESCUTCHEON BASE (U) 1SD697S APH
E3 F800L8L70SCP ESCUTCHEON BASE (U) 1SD677S CPH
E3 F800L8M30SAP ESCUTCHEON BASE (U) 1SD667S APH
E4 F66167D00AP FLAT CABLE 1SD697S APH,SD677S CPH,SD667S APH
E6 F80725Y00SAP DOOR OPENING BUTTON (U) 1SD697S APH,SD677S CPH,SD667S APH
E7 F82565Y00AP DOOR OPENING LEVER 1SD697S APH,SD677S CPH,SD667S APH
E8 F80375K00AP COOK BUTTON SPRING 1
E9 F630Y8M00BAP MEMBRANE SWITCH (U) 1SD697S APH
E9 F630Y7D00SCP MEMBRANE SWITCH (U) 1SD677S CPH
E9 F630Y7D00SAP MEMBRANE SWITCH (U) 1SD667S APH
E10 F90095X00AP GROUNDING PANEL 1SD697S APH,SD677S CPH,SD667S APH
E11 F803G7D00BAP POP-UP DIAL (U) 1SD697S APH,SD677S CPH,SD667S APH
E12 F80187D00BAP BACKSTOP 1SD697S APH,SD677S CPH,SD667S APH
E15 F00078M00SAP NAME PLATE 1SD697S APH
E15 F00078L70SCP NAME PLATE 1SD677S CPH
E15 F00078M30SAP NAME PLATE 1SD667S APH
17
NN-SD697S / NN-SD677S / NN-SD667S / NN-SN677S / NN-SN667 / NN-SN657S / NN-SA647 / NN-ST677S / NN-ST657W

7.5.2. NN-SN677S APH
Ref. No. Part No. Part Name & Description Pcs/Set Remarks
E21 F603L8M50AP D.P.CIRCUIT (AU) 1SN677S APH
E22 F603Y7D60AP D.P.CIRCUIT (DU) 1SN677S APH
E23 F800L8M50SAP ESCUTCHEON BASE (U) 1SN677S APH
E24 F66164W20AP FLAT CABLE 1SN677S APH
E25 F82986K10AP BUTTON 1SN677S APH
E26 F80725Y00SAP DOOR OPENING BUTTON (U) 1SN677S APH
E27 F82566K10AP DOOR OPENING LEVEL 1SN677S APH
E28 F80375K00AP COOK BUTTON SPRING 1
E30 F90095X00AP GROUNDING PANEL 1SN677S APH
E35 F00078M50SAP NAME PLATE 1SN677S APH
7.5.3. NN-SN657S APH, ST677S RPH/RTH
Ref. No. Part No. Part Name & Description Pcs/Set Remarks
E41 F603L8M70AP D.P.CIRCUIT (AU) 1SN657S APH
E41 F603L8R10RP D.P.CIRCUIT (AU) 1ST677S RPH/RTH
E43 F800L8M70SAP ESCUTCHEON BASE (U) 1SN657S APH
E43 F800L8R10SRP ESCUTCHEON BASE (U) 1ST677S RPH/RTH
E46 F80725Y00SAP DOOR OPENING BUTTON (U) 1SN657S APH,ST677S RPH/RTH
E47 F82565Y00AP DOOR OPENING LEVER 1SN657S APH,ST677S RPH/RTH
E48 F80375K00AP COOK BUTTON SPRING 1
E49 F630Y8M70BAP MEMBRANE SWITCH (U) 1SN657S APH
E49 F630Y6R10BRP MEMBRANE SWITCH (U) 1ST677S RPH/RTH
E50 F90095X00AP GROUNDING PANEL 1SN657S APH,ST677S RPH/RTH
E55 F00078M70SAP NAME PLATE 1SN657S APH
E55 F00078R10SRP NAME PLATE 1ST677S RPH
E55 F00078R20SRP NAME PLATE 1ST677S RTH
18
NN-SD697S / NN-SD677S / NN-SD667S / NN-SN677S / NN-SN667 / NN-SN657S / NN-SA647 / NN-ST677S / NN-ST657W

7.5.4. NN-SN667B/W/BB/WB/MB APH, SN667B/W CPH
Ref. No. Part No. Part Name & Description Pcs/Set Remarks
E61 F603L8M60AP D.P.CIRCUIT (AU) 1SN667B/W/BB/WB/MB APH
E61 F603L8M60CP D.P.CIRCUIT (AU) 1SN667B/W CPH
E62 F603Y7D60AP D.P.CIRCUIT (DU) 1SN667B/W/BB/WB/MB APH
E62 F603Y7D60CP D.P.CIRCUIT (DU) 1SN667B/W CPH
E63 F80348M60BAP ESCUTCHEON BASE 1SN667B/BB APH,SN667B CPH
E63 F80348M60HAP ESCUTCHEON BASE 1SN667W/WB APH,SN667W CPH
E63 F80348M60SAP ESCUTCHEON BASE 1SN667MB APH
E64 F66164W20AP FLAT CABLE 1SN667B/W/BB/WB/MB APH,SN667B/W CPH
E65 F82988M60KAP BUTTON 1SN667B/W/BB/WB/MB APH,SN667B/W CPH
E66 F80728M60BAP DOOR OPENING BUTTON 1SN667B/BB APH,SN667B CPH
E66 F80728M60HAP DOOR OPENING BUTTON 1SN667W/WB APH,SN667W CPH
E66 F80728M60SAP DOOR OPENING BUTTON 1SN667MB APH
E67 F82566K10AP DOOR OPENING LEVER 1SN667B/W/BB/WB/MB APH,SN667B/W CPH
E68 F80375K00AP COOK BUTTON SPRING 1
E69 F630Y8M60BAP MEMBRANE SWITCH (U) 1SN667B/BB/MB APH
E69 F630Y8M60HAP MEMBRANE SWITCH (U) 1SN667W/WB APH
E69 F630Y8M60BCP MEMBRANE SWITCH (U) 1SN667B CPH
E69 F630Y8M60HCP MEMBRANE SWITCH (U) 1SN667W CPH
E75 F00078M60BCP NAME PLATE 1SN667B CPH
E75 F00078M60HCP NAME PLATE 1SN667W CPH
19
NN-SD697S / NN-SD677S / NN-SD667S / NN-SN677S / NN-SN667 / NN-SN657S / NN-SA647 / NN-ST677S / NN-ST657W

7.5.5. NN-SA647B/W APH
Ref. No. Part No. Part Name & Description Pcs/Set Remarks
E81 F603L8M90AP D.P.CIRCUIT (AU) 1SA647B/W APH
E83 F80346K50BAP ESCUTCHEON BASE 1SA647B APH
E83 F80346K50HAP ESCUTCHEON BASE 1SA647W APH
E89 F630Y6K80BAP MEMBRANE SWITCH (U) 1SA647B APH
E89 F630Y6K80HAP MEMBRANE SWITCH (U) 1SA647W APH
E90 L5AAAEC00056 DISPLAY 1SA647B/W APH
E91 F66175L00AP DISPLAY TUBE COVER 1SA647B/W APH
E92 F67005U40XN RUBBER CONNECTOR 1SA647M APH
7.5.6. NN-ST657W RPH/RTH
Ref. No. Part No. Part Name & Description Pcs/Set Remarks
E101 F603L8R10RP D.P.CIRCUIT (AU) 1ST657W RPH/RTH
E103 F80348F70HQP ESCUTCHEON BASE 1ST657W RPH/RTH
E106 F80728F70HQP DOOR OPENING BUTTON 1ST657W RPH/RTH
E107 F82566K10AP DOOR OPENING LEVEL 1ST657W RPH/RTH
E108 F80375K00AP COOK BUTTON SPRING 1
E109 F630Y8R30HRP MEMBRANE SWITCH (U) 1ST657W RPH/RTH
20
NN-SD697S / NN-SD677S / NN-SD667S / NN-SN677S / NN-SN667 / NN-SN657S / NN-SA647 / NN-ST677S / NN-ST657W