Parallax Acrylic PING))) 725-32008 User manual

Web Site: www.parallax.com
Forums: forums.parallax.com
Sales: [email protected]
Technical: [email protected]
Office: [phone]
Fax: [phone]
Sales: [phone]
Tech Support: [phone]
Copyright © Parallax Inc. 725-32008 Acrylic PING))) Stand w/Hardware v1.0 11/22/2011 Page 1 of 1
Acrylic PING))) Stand w/Hardware (#725-32008)
This handy stand, made of smoke-colored 0.220” thick acrylic, makes it easy to mount a
PING)))TM Ultrasonic Distance Sensor (#28015) to your project. Mounting hardware included.
Packing List
(1) Acrylic PING))) Stand
(2) 1/16” Nylon spacers (#700-00015)
(2) 1/4” Nylon spacers (713-00005)
(2) #4-40x5/8” black pan head screws (#710-00035)
(2) #6-32x1/2” socket-head screws (#713-00033)
Additional Items Required
Small Phillips screwdriver
7/32” ball-end hex key (#725-00021)
PING))) Ultrasonic Distance Sensor (#28015)
3-wire F/F Extension Cable
(10-inch, #805-00001; 14-inch #805-00002)
Assembly Instructions
Step 1: Remove the protective paper from both sides of the Acrylic PING))) stand and lay it
etched-side down on a smooth, flat surface.
Step 2: Place a 1/16” spacer onto
each of the screws, and then insert the
screws through the PING))) sensor’s
PCB. Slide a 1/4” nylon spacer onto
each screw on the other side of the
PCB and then place the assembly onto
the backside of the acrylic stand. The
screws will cut their own threads as
you screw them in with a small Phillips
screwdriver. Make them snug, but do
not over-tighten.
Step 3: Pre-drill two holes into the
platform that you want to mount your
acrylic PING))) stand to. The mounting
holes are spaced 1.75” apart. The #6-32
x 1/2” long cap screws will extend about
1/4” into your platform. Depending on
the platform, you may wish to drill a
through hole, and secure with a washer
and nut (not included in this kit). For a
cleaner installation, simply drill a slightly
under-sized hole (such as with a #36 bit),
and have the screws cut their own
threads as you twist them into your
platform.
Step 4: Connect the cable to the PING))) sensor, and to your control board. Be sure to
observe proper polarity, as shown in the PING))) sensor’s documentation (#28015).

X-ON Electronics
Largest Supplier of Electrical and Electronic Components
Click to view similar products for Other Development Tools category:
Click to view products by Parallax manufacturer:
Other Similar products are found below :
DS100BR410EVK-4/NOPB BK0004 BK0012 SN65MLVD2-3EVM DS80EP100-EVK MAX9684EVKIT# MAX4952AEVKIT+ ESD-
EVM-001 MAX14842EVKIT+ EVAL01-HMC749LC3C 410-320 TPD6F002-Q1EVM TS9002DB DS80PCI800EVK/NOPB 118777-
HMC722LC3C 118777-HMC723LC3C 118777-HMC678LC3C DC1765A-A 125614-HMC851LC3C DC2178A-A TPD1E05U06DPYEVM
SN65LVDM31-32BEVM DC2062A-A NB4N855SMEVB LMH6321MR-EVAL/NOPB EVAL01-HMC747LC3C 4537 DK-M3F-1.8-TRK-
1.5-S DK-M3-FS-1.8-1.5-M12/16 DK-M3-LS-1.8-6 ADALM1000 ADALP2000 EVAL-CN0202-SDPZ EVAL-CN0203-SDPZ EVAL-
CN0204-SDPZ EVAL-CN0209-SDPZ EVAL-CN0225-SDPZ EVAL-CN0229-SDPZ EVAL-CN0251-SDPZ EVAL-CN0272-SDPZ EVAL-
CN0301-SDPZ EVAL-CN0325-SDPZ EVAL-CN0355-PMDZ EVAL-CN0364-SDPZ EVAL-SDP-CB1Z DS1964SEVKIT#
MAX14611EVKIT# MAX22088EVKIT# MAX4951AEEVKIT+ MAXREFDES60#