Parkside PABS 18-Li B3 User manual

IAN 90877
CORDLESS DRILL PABS 18-Li B3
AKKU-BOHRSCHRAUBER
Bedienungs- und Sicherheitshinweise
Originalbetriebsanleitung
AKU ODVIJAČ
Upute za posluživanje i za Vašu sigurnost
Prijevod originalnih uputa za uporabu
ŞURUBELnIţă CU ACUmULAtOR
Instrucţiuni de utilizare şi de siguranţă
Traducerea instrucţiunilor de utilizare originale
АКУМУЛАТОРНА БОРМАШИНА
Инструкции за обслужване и безопасност
Превод на оригиналното ръководство за експлоатация
Ε ΠΑΝΑΦΟΡΤΙΖΟΜΕΝΟ ΔΡΑΠΑΝΟΚΑΤΣΑΒΙΔΟ
Υποδείξει χειρισού και ασφαλεία
Μετάφραση των αυθεντικών οδηγιών λειτουργίας
CORDLESS DRILL
Operation and Safety Notes
Translation of original operation manual

GB Operation and Safety Notes Page 5
HR Upute za posluživanje i za Vašu sigurnost Stranica 15
RO Instrucţiuni de utilizare şi de siguranţă Pagina 25
BG Инструкции за обслужване и безопасност Страница 35
GR Υποδείξει χειρισού και ασφαλεία Σελίδα 45
DE/AT/CH Bedienungs- und Sicherheitshinweise Seite 55
Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of the
device.
Prije nego što pročitate tekst, otvorite stranicu sa slikama i upoznajte se na osnovu toga sa svim funkcijama
uređaja.
Înainte de a citi instrucţiunile, priviţi imaginile şi familiarizaţi-vă cu toate funcţiile aparatului.
Преди да прочетете отворете страницата с фигурите и след това се запознайте с всички функции
на уреда.
Πριν ξεκινήσετε την ανάγνωση, ανοίξτε τη σελίδα ε τι εικόνε και εξοικειωθείτε ε όλε τι λειτουργίε τη
συσκευή.
Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen
Funktionen des Gerätes vertraut.

A B
10
C
1
2
3
6
7
8
13
6
7
4
1415
9
5
11 12

5GB
Table of contents
Introduction
Intended purpose................................................................................................................................Page 6
Equipment Components......................................................................................................................Page 6
Scope of delivery................................................................................................................................Page 6
Technical Data ....................................................................................................................................Page 6
General safety advice for electrical power tools
1. Workplace safety...........................................................................................................................Page 7
2. Electrical safety...............................................................................................................................Page 7
3. Personal safety................................................................................................................................Page 8
4. Careful handling and use of electrical power tools.....................................................................Page 8
5. Use and handling of the cordless electrical power tool ..............................................................Page 9
6. Service.............................................................................................................................................Page 9
Safety advice relating to cordless drill drivers ..................................................................................Page 9
Safety notices for chargers.................................................................................................................Page 9
Supplementary Instructions.................................................................................................................Page 9
Original ancillaries/accessories .......................................................................................................Page 10
Start-up
Charging the battery pack .................................................................................................................Page 10
Insertion/removal of a battery pack into the appliance..................................................................Page 10
Checking battery status ......................................................................................................................Page 10
Changing tools....................................................................................................................................Page 10
Torque pre-selection............................................................................................................................Page 11
2 Gear Drive .......................................................................................................................................Page 11
Operation
Switching On/Off..............................................................................................................................Page 11
Setting the speed.................................................................................................................................Page 11
Switching direction of rotation ...........................................................................................................Page 11
Tips and Tricks.....................................................................................................................................Page 11
Maintenance and Cleaning..............................................................................................Page 12
Warranty.........................................................................................................................................Page 12
Disposal............................................................................................................................................Page 12
Conformity Declaration/Manufacturer................................................................Page 13

6 GB
Cordless drill PABS 18-Li B3
Introduction
We congratulate you on the purchase of your new
device. You have chosen a high quality product. The
instructions for use are part of the product. They
contain important information concerning safety,
use and disposal. Before using the product, please
familiarise yourself with all of the safety information
and instructions for use. Only use the unit as de scribed
and for the specified applications. If you pass the
product on to anyone else, please ensure that you
also pass on all the documentation with it.
Intended purpose
This appliance is designed for drilling and screwing
into wood, plastic and metal. Use the appliance only
as described and only for the purposes indicated.
Any other uses, and modifications to the appliance,
are deemed to be improper usage and may result
in serious physical injury. The manufacturer accepts
no responsibility for damage(s) resulting from
improper usage. The appliance is not intended for
commercial use.
Equipment Components
1Gear selector switch
2Direction of rotation switch/lock
3ON/OFF Switch/R.P.M. regulator
4Bit holder
5Belt clip
6Rechargeable battery pack
7Battery pack release button
8Rechargeable battery display LED
9Rechargeable battery charge state button
10 LED working light
11 Drill chuck
12 Torque pre-selector
13 Fast charger
14 Red charge-control LED
15 Green charge-control LED
Scope of delivery
1 Cordless drill with rechargeable battery pack
1 Bit PH2 50mm
1 Fast charger
1 Carry case
1 Directions for use
Technical Data
PABS 18-Li B3 Cordless drill:
Nominal voltage: 18V
Idle-running speed: 1st gear: max. 400min-1
Idle-running speed: 2nd gear: max. 1400min-1
Drill chuck
clamping range: max. 13mm
Maximum
drill diameter: Steel: 13mm,
Wood: 30mm
PABS 18-Li B3-1 Battery Pack:
Type: LITHIUM-ION
Nominal voltage: 18V
Capacity: 1.3Ah
Energy content: 23.4Wh
PABS 18-Li B3-2 Fast Charger:
INPUT
Nominal voltage: 230–240V∼, 50Hz
Power input: 45W
OUTPUT
Nominal voltage: 18V
Charging current 1.5A
Charging time: approx. 60 min
Protection class: II/
Noise and vibration data:
Measured values for noise are determined in accor-
dance with EN 60745. The A-weighted noise level
of the electrical power tool are typically:
Sound pressure level: 69dB(A)
Sound power level: 80dB(A)
Uncertainty K: 3dB
Introduction/General safety advice for electrical power tools
Introduction

7GB
Total vibration (vector sum of three directions) is
calculated in accordance with EN 60745:
Screwing: Vibration emission value
ah = 0.824m/s2,
uncertainty K = 1.5m/s2,
Drilling: Vibration emission value
ah,D = 2.47m/s2,
uncertainty K = 1.5m/s2.
The vibration level specified in
these instructions was measured in accordance with
an EN 60745 standardised measurement process
and can be used to compare equipment. The vibra-
tion emission value specified can also serve as a
preliminary assessment of the exposure.
The vibration level will change according to the ap-
plication of the electrical tool an in some cases may
exceed the value specified in these instructions. Re-
gularly using the electric tool in such a way may
make it easy to underestimate the vibration.
Note: If you wish to make an accurate assessment
of the vibration loads experienced during a particular
period of working, you should also take into account
the intervening periods of time when the device is
switched off or is running but is not actually in use.
This can result in a much lower vibration load over
the whole of the period of working.
General safety advice for
electrical power tools
Read all the safe-
ty advice and instructions! Failure
to observe the safety advice and instruc-
tions may result in electric shock, fire and/or seri-
ous injury.
Keep all the safety advice and instructions
in a safe place for future reference!
The term “electrical tool” used in the safety advice
refers to electrical tools powered by mains electricity
(by means of a mains lead) and electrical tools pow-
ered by rechargeable batteries (without a mains lead).
1. Workplace safety
a) K eep your working area clean and wel l
lit. Untidy or poorly lit working areas can lead
to accidents.
b) Do not work with the device in poten-
tially explosive environments in which
there are inflammable liquids, gases o r
dusts. Electrical power tools create sparks,
which can ignite dusts or fumes.
c) Keep children and other people away
while you are operating the electrical
tool. Distractions can cause you to lose con-
trol of the device.
2. Electrical safety
a) The mains plug on the power tool (or
on the power supply) must fit the mains
socket. Never modify the plug in any
way. Never use adapter plugs with
earthed power tools. Unmodified plugs
and the correct sockets reduce the risk of elec-
tric shock.
b) Avoid touching earthed surfaces such
as pipes, radiators, ovens and refrig-
erators with any part of your body.
There is an increased risk of electric shock if
your body is earthed.
c) Keep the device away from rain or
moisture. Water entering an electrical device
increases the risk of electric shock.
d) Do not use the mains lead for any pur-
pose for which it was not intended, e. g.
to carry the device, to hang up the de-
vice or to pull the mains plug out of
the mains socket. Keep the mains lead
away from heat, oil, sharp edges or
moving parts of the device. Damaged or
tangled mains leads increase the risk of elec-
tric shock.
e) When working outdoors with an elec-
trical power tool always use extension
cables that are also approved for use
outdoors. The use of an extension cable suit-
able for outdoor use reduces the risk of elec-
tric shock.
Introduction/General safety advice for electrical power tools
Introduction

8 GB
f) Use a residual current device (RCD) for
protection if operating the electrical
power tool in a moist environment is
unavoidable. The use of an RCD reduces
the risk of electric shock.
3. Personal safety
a) Remain alert at all times, watch what
you are doing and always proceed
with caution. Do not use the device if
you are tired or under the influence of
drugs, alcohol or medication. One mo ment
of carelessness when using the device can lead
to serious injury.
b) Wear personal protective equipment
and always wear safety glasses. The
wearing of personal protective equipment such
as dust masks, non-slip safety shoes, safety hel-
mets or ear protectors, appropriate to the type
of electrical power tool used and work under-
taken, reduces the risk of injury.
c) Avoid accidental starting. Verify the po-
wer tool is switched off before connec-
ting it to the mains and/or connecting
the battery, picking it up, or carrying it.
Accidents can happen if you carry the device
with your finger on the ON/OFF switch or with
the device switched on.
d) Remove any setting tools or spanners
before you switch the device on. A tool
or spanner left attached to a rotating part of a
device can lead to injury.
e) Avoid placing your body in an unnat-
ural position. Keep proper footing and
balance at all times. By doing this you will
be in a better position to control the device in
unforeseen circumstances.
f) Wear suitable clothing. Do not wear
loose clothing or jewellery. Keep your
hair, clothing and gloves clear of mov-
ing parts. Loose clothing, jewellery or long
hair can become trapped in moving parts.
g) If vacuum dust extraction and collection
devices are fitted do not forget to
check
that they are properly connected and
correctly used. The use of these devices
reduces the hazard presented by dust.
4. Careful handling and use
of electrical power tools
a) Do not overload the device. Always
use an electrical power tool that is
intended for the task you are under-
taking. By using the right electrical power
tool for the job you will work more safely and
achieve a better result.
b) Do not use an electrical power tool if
its switch is defective. An electrical power
tool that can no longer be switched on and off
is dangerous and must be repaired.
c) Pull the mains plug out of the socket
and/or remove the rechargeable bat-
terybefore you make any adjustments
to the device, change accessories or
when the device is put away. This pre-
caution is intended to prevent the device from
unintentionally starting.
d) When not in use always ensure that
electrical power tools are kept out of
reach of children. Do not let anyone use
the device if he or she is not familiar
with it or has not read the instructions
and advice. Electrical power tools are dan-
gerous when they are used by inexperienced
people.
e) Look after the device carefully. Check
that moving parts are working prop-
erly and move freely. Check for any
parts that are broken or damaged
enough to detrimentally affect the
functioning of the device. Have dam-
aged parts repaired before you use
the device. Many accidents have their origins
in poorly maintained electrical power tools.
f) Keep cutting tools clean and sharp.
Carefully maintained cutting tools with sharp
cutting edges are less likely to jam and are
easier to control.
g) Use the electrical power tool, accesso-
ries, inserted tools etc. in accordance
with these instructions and advice, and
General safety advice for electrical power tools
General safety advice for electrical power tools

9GB
the stipulations drawn up for this par-
ticular type of device. In doing this, take
into account the working conditions
and the task in hand. The use of electrical
power tools for purposes other than those in-
tended can lead to dangerous situations.
5. Use and handling of the cord-
less electrical power tool
a) Charge a rechargeable battery unit
using only the charger recommended
by the manufacturer. Chargers are often
designed for a particular type of rechargeable
battery unit. There is the danger of fire if other
types of rechargeable battery units are used.
b) Only the rechargeable battery units
supplied are to be used with an elec-
trical power tool. The use of other recharge-
able battery units may lead to the danger of
injury or fire.
c) When they are not being used, store
rechargeable battery units away from
paperclips, coins, keys. nails, screws
or other small metal objects that could
cause the contacts to be bridged. Short-
circuiting the contacts of a rechargeable battery
unit may result in heat damage or fire.
d) Fluids may leak out of rechargeable
battery units if they are misused. If this
happens, avoid contact with the fluid.
If contact occurs, flush the affected area
with water. Seek additional medical
help if any of the fluid gets into your
eyes. Escaping battery fluid may cause skin
irritation or burns.
CAUTION! DANGER OF EXPLOSION!
The batteries must never be recharged!
6. Service
a) Have your device repaired at the ser-
vice centre or by qualified specialist
personnel using original manufacturer
parts only. This will ensure that your device
remains safe to use.
Safety advice relating to
cordless drill drivers
Hold the device by the
insulated handle surfaces when you
are undertaking work where there is
the danger of the screw striking hidden
electricity cables or the device’s mains
lead. Contact of the screw with a live wire could
cause metal parts of the device to become live
and lead to electric shock.
Safety notices for chargers
Children or persons who lack the knowledge or
experience to use the device or whose physical,
sensory or intellectual capacities are limited
must never be allowed to use the device without
supervision or instruction by a person responsi-
ble for their safety. Children must never be
allowed to play with the device.
Supplementary Instructions
Securely support the workpiece. A workpiece
held in a clamp or vice is kept more securely in
place than one held by your hand.
POISONOUS DUSTS!
Harmful/noxious dusts generated from your
work represent a risk to the health of the person
operating the device and to anyone near the
work area. Wear safety glasses and a dust mask!
Do not drill any material containing
asbestos. Asbestos is a known carcinogen.
Hold the electrical power tool firmly.
High reaction torques may occur momentarily
during tightening or loosening of screws.
If the inserted tool jams, switch off the
electrical power tool immediately. Be
prepared for high reaction torques as they may
cause kickback. The inserted tool may jam if
the electrical power tool is overloaded or is
held at an angle to the workpiece.
Before you carry out any tasks on the
device, transport or store it, make sure
that the direction of rotation switch is
General safety advice for electrical power tools
General safety advice for electrical power tools

10 GB
in the middle position (lock). To prevent
the device from starting up unintentionally.
DANGER! Take steps to ensure that
you do not hit upon any service lines
(electricity, gas, water) when work-
ing with electrical appliances. Check, if
need be with a service line detector, before
you start to cut or bore into a surface.
Original ancillaries/
accessories
Use only the ancillaries and accessories
that are detailed in the operating
instructions. The use of ancillaries and ac-
cessories other than those recommended in the
operating instructions could lead to an increased
risk of personal injury for you.
Start-up
Charging the battery pack
CAUTION! Always ensure the plug is removed
from the mains socket before inserting a battery pack
into, or removing one from, the charging station.
Never charge the battery pack if the ambient
temperature is less than 10°C or greater than
40°C.
1. Insert the battery pack 6into the quick-
charger 13 (see Fig. C).
2. Insert the mains plug into the mains socket. The
flashing green charge indicator LED 15 shows
that charging is in progress.
3. The charging process is completed when the
green charge indicator LED 15 light up and the
accumulator pack 6is ready for operation.
4. If the red charge indicator LED 14 lights up, the
quick battery charger 13 is in standby mode;
the accumulator pack 6is not connected.
5. If the red charge indicator LED 14 starts flas-
hing, this means that the accumulator pack 6
has become too hot; no charging process.
Never charge the battery pack for a second time
immediately after a fast charging process has
been completed. This can give rise to the battery
pack becoming overcharged and to a reduced
service life of the battery and charging station.
Switch the charger off for at least 15 minutes
between two successive charging procedures.
Remove the power plug from the wall socket.
Insertion/removal of a battery
pack into the appliance
Inserting the rechargeable battery pack:
Move the rotation switch 2into the middle
position (lock). Push the rechargeable battery
pack 6into the handle until it engages.
Removing the rechargeable battery pack:
Press the release button 7and remove the
rechargeable battery pack
Checking battery status
To check the battery status, press the battery
LED button 9(refer to main diagram).
The three battery LEDs 8indicate the condition
and the remaining charge as follows:
GREEN/RED/ORANGE = maximum charge/
capacity
RED/ORANGE = medium charge/capacity
RED = weak charge – recharge battery
Changing tools
Your cordless drill has a fully automatic spindle
lock .
Once the motor has come to a halt, the drive shaft
is automatically locked, so that the chuck 11 can
be opened simply by turning it .
After you have inserted the required bit and fixed it
in place by turning the chuck , you can immedi-
ately continue working. The spindle lock releases
itself automatically when the motor is started (by
operation of the ON/OFF switch 3).
Start-up/Operation
General safety advice for electrical power tools/Start-up

11GB
Torque pre-selection
You can adjust the torque by using 12 torque pre-
selection.
Select a low setting for small screws, soft work
material.
Select a high setting for large screws, hard
work materials and for the extraction of screws.
For drilling, push the selector to the setting for
drilling, in that you adjust the torque pre-selector
to the position .
2 Gear Drive
CAUTION! Move the gear selector switch 1
only after the device has come to a standstill.
Failure to observe this advice may result in damage
to the device.
In the first gear (Gear selector switch 1
in Position: 1)
A speed of up to approx. 400 rpm can be achieved
and a high torque. This setting is intended for use w ith
all screwing tasks and for accessories (see example
Fig. B).
In the second gear (Gear selector switch 1
in Position: 2)
It achieves a speed of up to approx. 1400 rpm, for
the carrying out of drilling tasks (see example Fig. A).
Operation
Switching ON/OFF
Switching on:
To start the appliance squeeze on the ON/
OFF switch 3and then keep it pressed down.
The LED working light 10 comes on with a slightly
or fully pressed ON/OFF switch 3and illumi-
nates the working area in poor lighting conditio ns.
Switching off:
To stop the appliance, release the ON/OFF
switch 3.
Setting the speed
The ON/OFF switch 3has a variable speed con-
trol device. Slight pressure on the ON/OFF switch
3will cause the rotation speed to slow down. With
increased pressure, the rotational speed will increase.
Note: The integrated engine brake means that the
device will come to a fast standstill.
Switching direction of rotation
To switch the direction of rotation, push the
direction of rotation switch 2to either the
right or to the left.
Tips and Tricks
Before you use the appliance, check to see
that the screw or drill bit is properly fitted, i.e.
located centrally in the chuck.
Screw bits are designated with their dimensions
and their shape. If you are unsure, always try
the particular screw bit out to see whether it sits
in the screw head without any free play.
Torque:
Smaller screws and bits in particular can be
easily damaged if you adjust the appliance
with too high a torque and/or rotation speed.
Hard screwdriving conditions (into metal):
Particularly high torques can occur, for example
with metal screws tightened by socket tool bits.
Select a lower rotation speed.
Soft screwdriving conditions (e.g. into
soft wood):
You should also select a low speed in order not to
damage the wood workpiece surface through con-
tact with the metal screw head. Use a countersinker.
When drilling into wood, metal and other
materials, take note of the following advice:
With small diameter drill bits use a high drill
speed. For large diameter drill bits, use a low
drill speed.
Start-up/Operation
General safety advice for electrical power tools/Start-up

12 GB
For hard materials, select a low drill speed.
For soft materials, select a high drill speed.
Secure or fix down the workpiece (if possible)
in a clamp or vice.
Mark the intended position of the hole with a
centre punch or a nail and select a low drill speed
for drilling.
Take the rotating drill bit out of the hole frequently
so that swarf or drill dust can be re-moved and
the hole and tool is ventilated.
Drilling in metal:
Use a metal drill bit (HSS). For the best results,
you should cool the bit with oil. Metal drill bits
can also be used to drill into plastic.
Drilling in stone:
Use a circular shafted masonry drill bit with a
hardened metal tip.
Drilling in wood:
Normally you should use a wood drill with a
centring point. For deep holes, use an auger type
bit. For large diameter holes, use a forstner bit.
You can screw small screws into soft wood
without the need for pre-drilling.
Maintenance and Cleaning
RISK OF INJURY! Switch the
device off, unplug from the mains socket and re-
move the battery before performing any work on
the device.
The cordless drill is maintenance-free.
Always keep the device clean, dry and free of
oil or grease.
Use a dry cloth to clean the housing.
If the connection cable needs
to be replaced, this repair must be performed
by the manufacturer or a representative to pre-
vent safety hazards.
Warranty
The warranty for this appliance is for 3
years from the date of purchase. The ap-
pliance has been manufactured with care
and meticulously examined before deliv-
ery. Please retain your receipt as proof
of purchase. In the event of a warranty
claim, please make contact by telephone
with our Service Department. Only in this
way can a post-free despatch for your
goods be assured.
The warranty covers only claims for material and
maufacturing defects, but not for transport damage,
for wearing parts or for damage to fragile compo-
nents, e.g. buttons or batteries. This product is for pri-
vate use only and is not intended for commercial use.
The warranty is void in the case of abusive and im-
proper handling, use of force and internal tampering
not carried out by our authorized service branch. Your
statutory rights are not restricted in any way by this
warranty.
The warranty period will not be extended by repairs
made unter warranty. This applies also to replaced
and repaired parts. Any damage and defects extant
on purchase must be reported immediately after
unpacking the appliance, at the latest, two days after
the purchase date. Repairs made after the expiration
of the warranty period are subject to payment.
GB
Service Great Britain
Tel.: [phone]
(0,10 GBP/Min.)
e-mail: k[email protected]
IAN 90877
Disposal
The packaging comprises exclusively en-
vironmentally-friendly material. Dispose
of it in your local recycling containers.
Disposal/Conformity Declaration/Manufacturer
Operation/Maintenance and Cleaning/Warranty/Disposal

13GB
Do not dispose of electrical
appliances with your domestic
waste!
According to the European Directive 2002/96/EC,
concerning used electrical and electronic appliances
and its implementation in national law, superannu-
ated electrical appliances must be collected and
disposed of via an environmentally suitable recy-
cling facility.
Do not dispose of rechargeable
batteries with your household
refuse!
Defective or worn out rechargeable batteries must
be recycled according to Directive 2006/66/EC.
Dispose of batteries and appliances over the existing
collection facilities.
Your local communal or municipal authorities can
provide information on how to dispose of the worn
out appliance.
Conformity Declaration/
Manufacturer
We, KOMPERNASS HANDELS GMBH, the person
responsible for documents: Mr Semi Uguzlu, BURG-
STRASSE 21, 44867 BOCHUM, GERMANY, hereby
declare that this product complies with the following
standards, normative documents and EU directives:
Machinery Directive
(2006/42/EC)
EC Low Voltage Directive
(2006/95/EC)
Electromagnetic compatibility
(2004/108/EC)
RoHS Directive
(2011/65/EU)
Applicable harmonized standards
EN 60745-1:2009+A11, EN 60745-2-1:2010
EN 60745-2-2:2010, EN 55014-1:2006+A1+A2
EN 55014-2:1997+A1+A2, EN 61000-3-2:2006+
A1+A2, EN 61000-3-3:2008
EN 60335-1:2002+A1+A11+A12+A2+A13+A14+
A15, EN 60335-2-29:2004, EN 62233:2008
Type/Appliance Designation:
Cordless drill PABS 18-Li B3
Date of manufacture (DOM): 07–2013
Serial number: IAN 90877
Bochum, 31.07.2013
Semi Uguzlu
- Quality Manager -
We reserve the right to make technical modifications
in the course of further development.
Disposal/Conformity Declaration/Manufacturer
Operation/Maintenance and Cleaning/Warranty/Disposal

14

15HR
Popis sadržaja
Uvod
Uporaba u skladu sa namjenom.................................................................................................. Stranica 16
Oprema......................................................................................................................................... Stranica 16
Opseg isporuke............................................................................................................................. Stranica 16
Tehnički podaci............................................................................................................................. Stranica 16
Opće sigurnosne upute za električni alat
1. Sigurnost na radnom mjestu .................................................................................................... Stranica 17
2. Električna sigurnost................................................................................................................... Stranica 17
3. Sigurnost osoba........................................................................................................................ Stranica 18
4. Pažljivo postupanje s električnim uređajima i njihovo korištenje........................................... Stranica 18
5. Uporaba i rukovanje akumulatorskim alatom ........................................................................ Stranica 19
6. Servis......................................................................................................................................... Stranica 19
Sigurnosne upute za akumulatorsku bušilicu............................................................................... Stranica 19
Sigurnosne upute za punjače....................................................................................................... Stranica 19
Dodatne upute .............................................................................................................................. Stranica 19
Originalna oprema/dodatni uređaji .......................................................................................... Stranica 20
Stavljanje u pogon
Punjenje paketa baterija............................................................................................................... Stranica 20
Umetanje paketa baterija u uređaj/vađenje paketa baterija................................................... Stranica 20
Provjeravanje aku-stanja............................................................................................................... Stranica 20
Zamjena alata............................................................................................................................... Stranica 20
Određivanje okretnog momenta unaprijed................................................................................. Stranica 21
2-brzinski mjenjač ......................................................................................................................... Stranica 21
Rukovanje
Uključivanje/Isključivanje............................................................................................................ Stranica 21
Podešavanje broja okretaja ......................................................................................................... Stranica 21
Promjena smjera okretanja........................................................................................................... Stranica 21
Savjeti i trikovi ............................................................................................................................... Stranica 21
Održavanje i čišćenje...................................................................................................... Stranica 22
Jamstveni list.......................................................................................................................... Stranica 22
Zbrinjavanje........................................................................................................................... Stranica 23
Izjava o sukladnosti/Proizvođač........................................................................ Stranica 23

16 HR
Uvod/Opće sigurnosne upute za električni alat
Uvod
Aku odvijač PABS 18-Li B3
Q Uvod
Čestitamo Vam na kupnji novog uređaja. Ovom
kupnjom odlučili ste se za visokokvalitetan proizvod.
Uputa za uporabu je sastavni dio ovog proizvoda.
Ona sadrži važne upute o sigurnosti, uporabi i
uklanjanju otpada. Prije upotrebe proizvoda upoz-
najte se sa svim njegovim uputama za korištenje i
sigurnosnim uputama. Koristite ovaj proizvod u
skladu s navedenim uputama te u navedene svrhe.
Ukoliko proizvod dajete nekoj drugoj osobi, pre-
dajte toj osobi također i sve upute.
QUporaba u skladu sa namjenom
Ovaj uređaj je namijenjen za bušenje i odvijanje u
drvetu, plastici i metalu. Koristite uređaj isključivo
na opisani način i u navedenim područjima primjene.
Svaki drugi način uporabe i svaka promjena uređaja
smatra se nenamjenskom i krije znatnu opasnost od
nastanka nezgode. Proizvođač ne preuzima odgo-
vornost od štete nastale uslijed korištenja uređaja
protivnog njegovoj namjeni. Uređaj nije namjenjen
za komercijalnu uporabu.
QOprema
1Prekidač za odabir stupnja brzine
2Prekidač za odabir smjera okretanja/blokada
3Prekidač Uklj.-Isklj./ Regulator broja okretaja
4Držač bita
5Pričvršćenje pojasa
6Komplet akumulatora
7Tipka za deblokiranje kompleta akumulatora
8LED pokazivača akumutalora
9Tipka stanje akumulatora
10 Radna LED-svjetiljka
11 Zaglavnik za svrdlo
12 Regulator za odabir okretnog momenta unaprijed
13 Uređaj za brzo punjenje
14 Crvena LED-signalizacija za kontrolu punjenja
15 Zelena LED-signalizacija za kontrolu punjenja
QOpseg isporuke
1 aku odvijač s u aku-pakovanjem
1 bit PH2 50mm
1 uređaj za brzo punjenje
1 kovčeg za nošenje
1 uputstvo za uporabu
QTehnički podaci
PABS 18-Li B3 aku odvijač:
nazivni napon: 18V
broj okretaja u
praznom hodu: 1. hod: maksimalno
400min-1
broj okretaja u
praznom hodu: 2. hod: maksimalno
1400min-1
raspon zaglavnika za svrdlo: maksimalno 13mm
maksimalan
promjer bušotine: čelik: 13mm,
drvo: 30mm
PABS 18-Li B3-1 aku-pakovanje:
tip: LITHIUM-ION
nazivni napon: 18V
kapacitet: 1,3Ah
sadržaj energije: 23,4Wh
PABS 18-Li B3-2 uređaj za brzo punjenje:
ULAZ/Input:
nazivni napon: 230–240V∼, 50Hz
potrošnja: 45W
IZLAZ/Output:
nazivni napon: 18V
struja punjenja: 1,5A
trajanje punjenja: oko 60min
zaštitna klasa: II/
Informacija o buci i vibraciji:
Mjerna vrijednost za buku utvrđena sukladno
EN 60745. A-ocjenjena razina buke električnog
alata iznosi tipično:
Razina zvučnog tlaka: 69 dB(A)
Razina snage zvuka: 80dB(A)
Nesigurnost K: 3dB

17HR
Ukupne vrijednosti titranja (vektorski zbroj triju
smjerova) su istražene sukladno EN 60745:
Vijak: Vrijednost emisije titranja
ah = 0,824m/s2,
Nesigurnost K= 1,5m/s2,
Bušenje: Vrijednost emisije titranja
ah,D = 2,47m/s2,
Nesigurnost K= 1,5m/s2.
Razina titranja, navedena u
ovim uputama, je istražena i određena sukladno
normiranom postupku mjerenja, koji je naveden u
EN 60745 i koji je prikladan za uspoređivanje stroja.
Navedena vrijednost emisije titranja se može koristiti
i za uvodnu procjenu izloženosti.
Razina titranja je promijenljiva, ovisno o korištenju
električnog alata, te može u pojedinim slučajevima
ležati iznad vrijednosti, navedene u ovim uputama.
Razina opterećenja titranja može biti podcjenjena,
ako se električni alat redovito koristi na takav način.
Uputa: Za precizno ocjenjivanje titrajnog otpere-
ćenja tijekom određenog radnog vremena, potrebno
je također uzeti u obzir vremena kad je stroj isključen,
ili je uključen ali se zapravo ne rabi. To može znatno
smanjiti titrajno opterećenje, tijekom cijelog radnog
vremena.
Opće sigurnosne upute
za električni alat
Pročitajte si-
gurnosne upute kao i sve ostale
upute! U slučaju ne pridržavanja sigur-
nosnih uputa kao i ostalih uputa, prijeti opasnost od
strujnog udara, požara i/ili teških ozljeda.
Sačuvajte sve sigurnosne upute kao i sve
ostale upute za ubuduće!
U sigurnosnim uputa rabljeni izraz „električni alat“
odnosi se na električne uređaje sa mrežnim pogo-
nom (sa mrežnim kabelom) i na električni alat sa
akumulatorskim pogonom (bez mrežnog kabela).
1. Sigurnost na radnom mjestu
a) Vodite uvijek računa o tome, da Vaše
radno mjesto bude čisto i dobro os-
vjetljeno. Nered i ne osvjetljeno područje
rada, može uzrokovati nezgode.
b) Ne rabite stroj u području gdje prijeti
opasnost od eksplozije, gdje se nalaze
zapaljive tekućine, plinovi ili prašine.
Električni alati proizvode iskre, koje mogu za-
paliti prašinu ili pare.
c) Za vrijeme uporabe električnog alata,
držite djecu i druge osobe izvan doh-
vata istoga. U slučaju nepažnje, možete
izgubiti kontrolu nad strojem.
2. Električna sigurnost
a) Mrežni utikač uređaja mora odgova-
rati utičnici.
Utikač se ni na kakav način
ne smije mijenjati. Ne koristite adap-
terske utičnice zajedno s zaštitno uze-
mljenim uređajima. Neizmijenjeni utikači
i odgovarajuće utičnice smanjuju rizik električ-
nog udara.
b) Izbjegavajte dodir tijela s uzemljenim
površinama kao što su cijevi, radijatori ,
pećnice i hladnjaci. Postoji povećana opa-
snost od električnog udara ukoliko je vaše tijelo
uzemljeno.
c) Uređaj držite podalje od kiše i vlage.
Prodiranje vode u unutrašnjost uređaja pove-
ćava opasnost električnog udara.
d) Ne koristite kabel u neke druge svrhe,
npr. za nošenje uređaja, vješanje ure-
đaja ili za izvlačenje utikača iz utičnice.
Kabel držite podalje od topline, ulja,
oštrih rubova i pokretnih dijelova ure-
đaja. Oštećeni ili spetljani kabel ili utikač po-
većava rizik električnog udara.
e) Kod rada na otvorenome koristite samo
produžni kabel koji je dozvoljen za
korištenje na otvorenome. Upotreba
produžnog kabla namijenjenog za korištenje n a
otvorenome smanjuje rizik električnog udara.
f) Ako je korištenje električnog alata u
vlažnim prostorima neizbježno, rabite
Uvod/Opće sigurnosne upute za električni alat
Uvod

18 HR
Opće sigurnosne upute za električni alat
zaštitnu strujnu sklopku. Korištenje zaštitne
strujne sklopke, smanjuje rizik strujnog udara.
3. Sigurnost osoba
a) Budite uvijek pozorni, vodite računa
o tome što radite i razumno pristupite
radu s električnim alatom. Ne rabite
stroj, ako ste umorni ili pod utjecajem
droga, alkohola ili lijekova. Jedan trenu tak
nepažnje za vrijeme korištenja stroja, može
uzrokovati teške ozljede.
b) Nosite osobnu zaštitnu opremu i uvijek
zaštitne očale. Korištenje osobne zaštitne
opreme, kao maske za prašinu, protuklizne
zaštitne cipele, zaštitnu kacigu ili štitnik za uši,
ovisno o vrsti i uporabi električnog alata,
smanjuje rizik od ozljeda.
c) Spriječite slučajno uključenje. Uvjerite
se u to, da je električni alat isključen,
prije uključenja na struju, podizanja
ili nošenja. Ako pri nošenju uređaja držite
prst na sklopki za UKLJUČENJE/ISKLJUČE-
NJE ili ako je uređaj uključen, prijeti opasnost
od nezgode.
d) Prije uključenja stroja, uklonite alat
za podešavanje ili vijčani ključ. Alat ili
ključ, koji se nalazi u rotirajućem dijelu stroja,
može prouzročiti ozljede.
e) Izbjegavajte nenaravan polažaj tijela.
Vodite računa o tome da sigurno stojite
na tlu i održavate vlastitu ravnotežu.
Na taj način bolje možete kontrolirati uređaj,
posebno u neočekivanim situacijama.
f) Nosite prikladnu odjeću. Ne nosite
široku odjeću ili nakit. Držite kosu,
odjeću i rukavice dalje od pomičnih
dijelova. Opuštena odjeća, nakit ili duga
kosa mogu biti zahvaćeni od pomičnih dijelova.
g) Ako se montira uređaje za usisavanje
i prihvaćanje prašine, uvjerite se u
to da su priključeni i da se pravilno
koriste. Uporaba tih uređaja, smanjuje
ugrožavanje od prašine.
4. Pažljivo postupanje s
električnim uređajima i
njihovo korištenje
a) Nemojte uređaj preopterećivati.
Koristite onaj električni uređaj koji
odgovara za Vaš rad. S odgovarajućim
električnim uređajem bolje i sigurnije ćete radi-
ti u navedenom području rada.
b) Ne koristite električni uređaj s neisprav-
nim prekidačem. Električni uređaj koji se više
ne može uključiti i isključiti opasan je i treba ga
dati popraviti.
c) Izvucite utikač iz utičnice i/ili otklonite
akumulator, prije namještanja uređaja,
zamjene pribora ili odlaganja uređaja.
Ta mjera zaštite spriječava slučajno uključenje
električnog alata.
d) Čuvajte ne korišteni električni uređaj
tako da nije na dohvatu djeci. Ne
dopustite da uređaj koriste osobe
koje s njim nisu upoznate ili koje nisu
pročitale upute. Električni alati su opasni
kada ih korite osobe bez iskustva.
e) Pažljivo održavajte uređaj. Kontroli-
rajte da li pokretni dijelovi uređaja
besprijekorno funkcioniraju i da ne
zapinju, da dijelovi nisu slomljeni ili
tako oštećeni da je funkcija uređaja
upitna. Molimo da oštećene dijelove
dadete popraviti prije korištenja ure-
đaja. Brojne nesreće imaju uzrok zbog loše
održavanih električnih alata.
f) Alat za rezanje treba biti oštar i čist.
Brižljivo njegovani alat za rezanje sa oštrim
reznim rubovima, manje zaglavi i jednostavniji
je za rukovanje.
g) Rabite električni alat, opremu i ugrad-
ni alat, itd. sukladno ovim uputama i
na način kako je propisano za ovaj
posebni tip uređaja. Pri tome uzmite
u obzir radne uvjete i rad koji se izvodi.
Uporaba električnog alata za drugu osim
predviđene primjene, može uzrokovati opasne
situacije.
Opće sigurnosne upute za električni alat

19HR
5. Uporaba i rukovanje
akumulatorskim alatom
a) Koristite samo one akumulatore koje
je preporučio proizvođač. Kod električnih
uređaja za koje su namijenjene samo određene
vrste akumulatora, postoji opasnost od izbijanja
požara ako se koriste sa drugim vrstama aku-
mulatora.
b) Akumulatore koristite samo u za njih
posebno namijenjenim uređajima.
Upotreba drugih akumulatora može dovesti
do ozljeda i opasnosti od izbijanja požara.
c) Držite neupotrjebljene akumulatore
daleko od kontakta s metalnim pred-
metima poput uredskih spajalica,
kovanica, ključeva, čavala i sl. Malih
metalnih predmeta koji bi mogli prouzročiti
prekid kontakta. Nakon takvog kontakta bi mo-
gao uslijediti kratki spoj koji bi za posljedicu
mogao imati opekline ili čak prouzročiti požar.
d) Kod neispravne upotrebe iz akumulato-
ra može iscuriti tekućina. Izbjegavajte
svaki kontakt s tom tekućinom. Nakon
mogućeg kontakta obavezno mjesto
kontakta isperite vodom. Ako tekućina
dođe u dodir s očima, odmah potražite
pomoć liječnika. Tekućina iz akumulatora u
kontaktu s kožom može prouzročiti ozljede i
opekline kože.
OPREZ! OPASNOST OD EKSPLOZIJE!
Nikada ne punite baterije koje nisu punjive!
6. Servis
a) Električne naprave smiju popravljati
samo ovlašteni serviseri ili električari.
Time ćete zadržati sigurnost vaših uređaja.
Sigurnosne upute za
akumulatorsku bušilicu
Držite uređaj na izoli-
ranim držkama, dok izvodite radove
pri kojima vijak može zahvatiti skrive-
ne električne vodove ili vlastiti mrežni
kabel. Dodir vijka sa vodom pod naponom
može također metalne dijelove uređaja staviti
pod napon i prouzročiti strujni udar.
Sigurnosne upute za punjače
Ovaj uređaj nije namijenjen osobama (uključivši
djecu) s ograničenim tjelesnim, senzoričnim ili
umnim sposobnostima i/ili koje nemaju iskustvo
ili znanje u ophođenju s uređajem, osim ako su
pod nadzorom osobe koja je zadužena za nji-
hovu sigurnost ili ako bi rabili uređaj prema
njenim uputama. Dijeca trebaju biti pod nadzo-
rom, kako se nebi igrala s uređajem.
Dodatne upute
Učvrstite predmet koji obrađujete. Koristite za-
tezne naprave ili škripac kako bi učvrstili pred-
met. Na taj način naprava je bolje učvršćena
nego vašom rukom.
OTROVNI PRAH !
Tijekom upotrebe naprave nastaju opasne/
otrovne čestice prašine koje mogu prouzročiti
opasnosti po zdravlje osoba koje se koriste
napravom ili osoba u neposrednoj blizini. Tije-
kom rada sa napravom uvijek koristite zaštitne
naočale i masku za zaštitu od prašine!
Ne obrađujte nikad materijale koji
sadrže azbest. Azbest izaziva rak.
Električni uređaj držite čvrsto u ruci.
Kod zatezanja i odvrtanja vijaka, može doći
do brzih i snažnih momenata otporne reakcije
uređaja.
Odmah isključite električni uređaj iz
struje u slučaju smetnji ili blokade ure-
đaja. Budite izuzetno oprezni kod rada stroja
i momenata reakcije ,koji mogu prouzročiti po-
vratni udarac. Alat kojim radite blokira, ako
dođe do preopterećenja električnog uređaja ili
ako se alat zaglavi u predmetu koji obrađujete.
Kod radova na uređaju, kao i kod
transporta, odnosno pospremanja
uređaja, obratni sklopnik (zaporka)
postavite na srednju poziciju. Tako ćete
priječiti ne namjerno uključivanje uređaja.
Opće sigurnosne upute za električni alat
Opće sigurnosne upute za električni alat

20 HR
Opće sigurnosne upute za električni alat/Stavljanje u pogon
OPASNOST! Provjerite, da ne naletite
na vodove struje, vode ili plina, kada
radite sa električnim uređajima. Eventu-
alno izvršite provjeru pomoću uređaja za traže-
nje vodova, prije nego što bušite ili otvarate zid.
QOriginalna oprema/
dodatni uređaji
Upotrebljavajte isključivo opremu i
dodatne uređaje navedene u uputama
za uporabu. Uporaba drugih alata i druge
opreme, koja nije navedena u ovim uputama,
može dovesti do opasnosti od ozljeda.
Stavljanje u pogon
QPunjenje paketa baterija
OPREZ! Uvijek izvucite mrežni utikač prije
vađenja paketa baterija iz punjača ili prije njegovog
postavljanja.
Nikada ne punite paket baterija, kada je vanj-
ska temperatura ispod 10°C ili iznad 40°C.
1. Stavite akumulatore 6u uređaj za brzo pu-
njenje 13 (vidi sliku C).
2. Utaknite mrežni utikač u utičnicu. LED za kontro-
lu punjenja 15 koja sad treperi zeleno, pokazuje
postupak punjenja.
3. Odmah čim LED za kontrolu punjenja 15 pre-
stane treperiti i stalno svijetli zeleno, postupak
punjenja je okončan, te se baterijski sklop 6
može odmah koristiti.
4. Ukoliko LED za kontrolu punjenja 14 zasvijetli
zeleno, punjač za brzo punjenje 13 nalazi se u
Standby-modu; baterijski sklop 6nije priključen.
5. Ukoliko LED za kontrolu punjenja 14 zasvijetli
crveno, baterijski sklop 6je postao prevruć;
postupak punjenja je prekinut.
Nikada ne vršite ponovno punjenje paketa
baterija neposredno nakon jednog brzog pu-
njenja. Postoji opasnost da se paket baterija
prepuni, nakon čega bi vijek trajanja punjača i
same baterije bio skraćen.
Punjač između dva postupka punjenja isključite
na minimalno 15 minuta. U tu svrhu izvucite
mrežni utikač.
QUmetanje paketa baterija u
uređaj/vađenje paketa baterija
Postavljanje kompleta akumulatora:
Namjestite preklopnika smjera vrtnje 2na
srednji položaj (blokiranje). Pustite da se akku-
komplet 6zaglavi u drški.
Vađenje aku-pakovanja:
Pritisnite tipku za deblokiranje 7i izvadite
aku-pakovanje.
QProvjeravanje aku-stanja
Pritisnite za provjeravanje aku-stanja tipku
Akku-LED 9(vidi također glavni prikaz).
Stanje odnosno ostatak snage bit će prikazan
pomoću tri akku-LED-žaruljice 8na slijedeći
način:
ZELENO/CRVENO/NARANČASTO = mak-
simalno punjenje/kapacitet
CRVENO/ NARANČASTO = srednje punje-
nje/kapacitet
CRVENO = slabo punjenje–aku puniti
QZamjena alata
Vaša akumulatorska bušilica i odvijač ima potpuno
automatsko aretiranje vretena .
Kada motor miruje, dolazi do blokade pogonske
osovine, tako da steznik za brzo umetanje svrdla 11
možete otvoriti okretanjem.
Nakon što ste umetnuli željeni alat i nakon što ste
ga okretanjem steznika učvrstili, možete odmah
nastaviti sa radom. Blokada igle automatski se otpušta
pokretanjem motora (aktiviranje prekidača Uklj./
Isklj. 3).