pasito a pacito Maria 474376 User manual

(A) (B)
(F)
TM
(G)
(C)
(D)
(E)
(H) (I )
1a
C
C
C
H
1
C
A
B
C
A
G
H
2
2a
3
D
A
B
A
D
G
G
4
G
E
A
E
E
E
E
A
B
4a
5
B
E
G
A
E
E
E
E
B
5a
6
F
C
A
I
I
F
F
C
B
A
CA
B
6a
ES

87
(A) Leg
(2 pcs)
(B) Leg
(2 pcs)
(E) Dowel Cross Rail
(4 pcs)
(F)
(2 Pcs)
Plastic Rail
(D) Curved Base Rail
(2 pcs)
(C) Side Rail (One with Warning Label attached)
(2 pcs)
TM
Assembly Hardware Set
(I ) 18mm Screw
(8 pcs)
(H) Wood Pin
(4 pcs)
(G)50mm Screw
(20 pcs)
Insert
Wooden Pins (H) into
the top hole on the Side Rails
(C) on both ends.
Repeat for
other side rail
1a
C
C
C
H
.
1Note: Angled edge of legs face outwards
as shown w ith t he larger holes f or t he
cross dowels on the same side facing in.
Place legs
with the
larger holes
facing
towards you.
The pilot
holes for the
plastic strap
should face
inside.
To attach the Side Rail (C) to the Legs (A & B) simply line up the wooden dowels you inserted in
Step 1 into the top hole on the surface of the legs. Ensure that you have one A leg and one B
leg as shown in image. Bolt together using the 50 mm Screws (G) tighten with Screw Driver
(not supplied). Repeat for other side.
C
A
B
C
A
G
H
2
2a
EN
ES

6
Now attach the Plastic Rail (F) by lining up
the two holes on the end with the two guide
holes on the Side Rails (C) as shown in 6a. You
will need a Philips screw driver for this task (not
supplied). Screw i n place. Repeat f or
other end o f plastic rail. When done s imply
attach the other plastic rail to the other end as
shown.
F
C
A
I
I
F
F
C
B
A
CA
B
6a
5
Place partially a ssembled unit on i ts s ide as
shown. Line up the second side assembly with
the four dowels and press together.
Ensure the
dowels are fully inserted into the holes. Secure
in place with four
50 mm Screws (G)
as shown.
B
E
G
A
E
E
E
E
B
5a
4
G
E
A
Insert one of the end of the Dowel Cross Rails (E) into the large hole on the side assembly. The
dowel should go into the hole tightly as shown in 4a. Some gentle tapping may be required.
Screwt he dowel into place with a
50 mm Screw (G)
and tighten in place. Repeat for the three
other ends of the dowels.
E
E
E
E
A
B
4a
3
Attach the Curved Base Rail (D) to the leg assembly with four
50 m m Screws ( G)
as s hown. Ensure screws a re t ightened
securely. Repeat for other side.
D
A
B
A
D
G
G
3a
87
EN

FR
(G)
(A)
(2 unités)
(B)
(F)
TM
(D)
(C)
(E)
(H) (I )
1a
C
C
C
H
1
C
A
B
C
A
G
H
2
2a
3
D
A
B
A
D
G
G
3a
4
G
E
A
E
E
E
E
A
B
4a
5
B
E
G
A
E
E
E
E
B
5a
6
F
C
A
I
I
F
F
C
B
A
CA
B
6a

FR
IT
(G)
(A) (B)
(F)
TM
(C)
(D)
(E)
(H) (I )
1a
C
C
C
H
1
C
A
B
C
A
G
H
2
2a

IT
3
D
A
B
A
D
G
G
4
G
E
A
E
E
E
E
A
B
5
B
E
G
A
E
E
E
E
B
6
F
C
A
I
I
F
F
C
B
A
CA
B
87

PT
Perna
(2 unidades)
(A)
Perna
(2 unidades)
(B)
(F)
TM
(G)
(C)
(D)
Base curva (2 unidades)
(E)
Haste (4 unidades)
(H) Espiga de madeira
(4 unidades)
(I ) Parafuso de 18 mm
(8 unidades)
1a
C
C
C
H
1
C
A
B
C
A
G
H
2
2a
3
D
A
B
A
D
G
G
3a
4
G
E
A
E
E
E
E
A
B
4a
5
B
E
G
A
E
E
E
E
B
5a
6
F
C
A
I
I
F
F
C
B
A
CA
B
6a

87 PT