PATIOROMA DSF011 User manual

DSF011

MAINTENANCE OF WICKER AND RATTAN FURNITURE
1. Keep your furniture out of direct sunlight to prevent fading or weakening.
2. Do not use or store near fire or heat sources to avoid deformation, bending, or cracking.
3. To clean first use a mild detergent and dry towel then wipe with a damp cloth, and lastly
wipe with a soft dry towel.
4. Each two (2) to five (3) years, wipe down the furniture using slightly saline (salty) water.
This will keep your furniture clean, durable, and help to prevent moth infestation.
5. Renovation: first clean the furniture, then polish it using a slightly abrasive paper to make
the surface smooth, and lastly brush on protective oil onto the surface.
SAFETY AND CARE ADVICE
1. Check you have all the components and tools
2. Keep children and animals away from the work area, small parts could choke if
swallowed.
3. Make sure you have enough space to layout the parts before starting.
4. Do not stand or put weight on the product during assembly, this could cause damage.
5. Assemble the item as close to its final position as possible.
6. Dispose of all packaging carefully and responsibly.
7. When tightening the screws, ensure that the holes are matched correctly and that parts
are kept perpendicular to each other.
Please read these instructions fully before starting assembly
Do not fully tighten all screws until assembly is complete.
Make sure the assemble will be easier with 2 people.
Friendly Tips
•
•
•

(A)x1 Back side
- 1 -
(B)x1 Left side (B1)x1Right side
The parts and hardwares below have been included for assembly
ARMCHAIR ASSEMBLY STEPS
(C)×1 Seat M6x35 9PCS (L)x1 Wrench

ASSEMBLY STEPS
A
B
M
BB1
BB1
C
C
A
B1
A
BB1
Step 1：Match the two(2) holes of parts
A and B.Match the two(2) holes of parts
A and B1.Insert the screws and twist by L.
Do not fully tighten all screws until
assembly is complete.
Note:There are 2 armchairs in the sofa set. And the part numbers and assembly are all
the same.
Step 2：Match the one (1) hole of parts C
and A. Match the two(2) holes of parts C
and B. Match the two(2) holes of parts C
and B1. Insert the screws and tighten all
the screws.
Screws Assembly Steps
match the two different
holes
insert screws
- 2 -
tighten the screws by
included wrench
Important: Do not fully tighten all screws until assembly is complete.

(A1)x1 Back side
- 3 -
(B)x1 Left side (B1)x1Right side
The parts and hardwares below have been included for assembly
LOVESEAT ASSEMBLY STEPS
(C1)×1 Seat M6x35 10PCS (L)x1 Wrench

ASSEMBLY STEPS
A1
B
B
A1
B1
BB1
C1 C1
B1
A1
BB1
Step 1: Match the two(2) holes of parts
A1 and B. Match the two(2) holes of parts
A1 and B1. Insert the screws and twist by
L.Do not fully tighten all screws until
assembly is complete.
Step 2: Match the two(2) holes of parts C1
and A1. Match the two(2) holes of parts
C1 and B. Match the two(2) holes of parts
C1 and B1, then insert the screws and
Twist. Tighten all the screws.
Screws Assembly Steps
match the two different
holes
insert screws
- 4 -
tighten the screws by
included wrench
Important: Do not fully tighten all screws until assembly is complete.

(D)x1 Top side
- 5 -
(L)x1 Wrench
(E)x2 L/R side (E1)x1
The parts and hardwares below have been included for assembly
TABLE CHAIR ASSEMBLY STEPS
M6x35 4PCS (L)x1 Wrench
M6x15 4PCS

ASSEMBLY STEPS
D
E
D
EE1
D
EE1
D
E
D
EE
E1
D
EE
E1
Step 1：Match the two(2) holes of parts E and
D and insert with M6x35 twist by L . Do not
fully tighten all screws until assembly is
complete.
Step 2：Match the two(2) holes of parts E and
D and insert with M6x35 twist by L . Do not
fully tighten all screws until assembly is
complete.
Screws Assembly Steps
match the two different
holes
insert screws
- 6 -
tighten the screws by
included wrench
Important: Do not fully tighten all screws until assembly is complete.
Step 3：Match the four(4) holes of parts E1
and E .Insert with M6x15 and tighten all the
screws.Ensure the table is stable,then place
the glass on top.

E-MAIL US:
We are here 7days a week to help you!
[email protected]
www.patioroma.com