PDi PDI-Z13TV SERIES Installation instructions

Communication
Systems Inc. MODEL PDI-Z13TV SERIES
13”ARM MOUNTED COLOR TV (WR) WIRED REMOTE Page 1of 5
Better Solutions Are Within Reach ™INSTALLATION & SAFETY INSTRUCTIONS
PDI Communication Systems, Inc. 40 Greenwood Lane Springboro, Ohio 45066 USA PH [phone] FX [phone]
PD 196-011 Rev 3
CAUTION
This symbol indicates that dangerous voltage
constituting a risk of electric shock is present
within this unit. RISK OF ELECTRIC SHOCK,
DONOT OPEN!
This symbol indicates that thereareimportant
operating and maintenance instructions in the
literature accompanying this unit.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER. NO USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL
THIS INSTALLATION SHOULD BE MADE BY A QUALIFIED SERVICE PERSON AND SHOULD CONFORM TO ALL LOCAL CODES.
READ AND FOLLOW THE SAFETY INSTRUCTIONS BEFORE ATTEMPTING THIS INSTALLATION.
Note to CATV installer. This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides
guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building,
as close to the point of cable entry into the room as practical.
WARNING:OXYGEN ENVIRONMENTDO NOT use
in an oxygen tent or oxygen chanber. Such use may
cause a fire hazard.
WARNING: To avoid the hazards of fire or electric
shock, DO NOT expose this TV to rain or moisture.
DANGER: ARM RECOIL HAZARD The safety
brake pin must remain in the SAFETY BRAKE PIN
HOLE whenever the television set is removed from
the arm or when the arm is removed from the wall
bracket to prevent the arm from springing open.
This TV is designed to mount on a model PD
I
-
405 suspension arm. Due to the TV’s weight and size, mounting on any other arm is NOT
recommended.
1. Place the arm’s base pin into
the wall bracket.
2. Open the nose cover and
remove the retainer plate.
3. Insert the TV swivel completely
in the clevis. Reinstall the
retainer plate. Replace the lock
washer and nut, and tighten
with a wrench.
4. The cable from the arm should
be joined with the television
cable, wrench tightened, and
the connection covered by
sliding the plastic boot sections
into mating position.
5. Position the cover in the front
and line up the cover pin holes.
Remove the safety brake pin
from the parking brake hole and
place it in the cover pin hole.
Tighten nut on safety brake pin.
6. Connect the coaxial cable at the
base of the arm to the wall
bracket “F” fitting. Wrench
tighten.
7. This Television for use only with
UL listed power supply maked
to indicate use with this
television.
INSTALL TV ON ARM
TO ARM TO TV
CABLE DETAIL
SAFETY BRAKE PIN
DETAIL
Acorn Nut & Lock Washer
Retainer Plate
Safety Brake
Pin Hole

Communication
Systems Inc. MODEL PDI-Z13TV SERIES
13”ARM MOUNTED COLOR TV (WR) WIRED REMOTE Page 2of 5
Better Solutions Are Within Reach ™INSTALLATION & SAFETY INSTRUCTIONS
PDI Communication Systems, Inc. 40 Greenwood Lane Springboro, Ohio 45066 USA PH [phone] FX [phone]
PD 196-011 Rev 3
14.
Lightning
–
For added protection during a lightning storm,
or when it is left
unattended and unused for long periods of time, unplug it from the wall outlet
and disconnect the antenna or cable system. This will prevent damage to the
TV due to lightning and power-line surges.
15. Power Lines –Do not locate an outside antenna system near overhead
power lines or other electric light or power circuit or where it can fall into such
lines or circuits.
16. Overloading –Do not overload wall outlets and extension cords as they can
result in a risk of fire or electric shock.
17. Object and Liquid Entry –Never push objects of any kind into this TV
through openings as they may touch dangerous voltage points or short out
parts, resulting in a fire or electric shock. Never spill liquid of any kind on the
TV.
18. Servicing –Do not attempt to service this TV yourself as opening or removing
covers may expose you to dangerous voltage or other hazards. Refer all
servicing to qualified service personnel.
19. Damage Requiring Service -Unplug this TV from the wall outlet and refer
servicing to qualified service personnel under the following conditions:
a. When the power-supply cord or plug is damaged or cut.
b. If liquid spills or objects fall into the TV.
c. If the TV is exposed to rain or water.
d. If the TV does not operate normally by following the operating
instructions. Adjust only those controls that are covered by the
operating instructions. An improper adjustment of other controls may
result in damage and will often require extensive work by a qualified
technician to restore the TV to its normal operation.
e. If the TV is dropped or the cabinet is damaged.
f. When the TV exhibits a distinct change in performance, this indicates a
need for service.
20. Replacement Parts –When replacement parts are required, be sure the
service technician uses replacement parts specified by the manufacturer or
which have the same characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock or other hazards.
21. SafetyCheck –Upon completion of any service or repairs to this TV, ask the
service technician to perform safety checks to determine that the TV is in
proper operating condition.
22. Wall or Ceiling Mounting –This TV should be mounted to a wall or ceiling
only as recommended by the manufacturer.
23. PeriodicMaintenance–ThisTVdoesnotrequireperiodicmaintenanceother
than cleaning.
Antenna
Lead -In
Wire
Antenna
Discharge Unit
(NEC Section 810-20)
Grounding Conductors
(NEC Section 810-21)
Ground Clamps
Power Service Grounding
Electrode System
(NEC ART 250, Part H)
Electric
Service
Equipment
NEC -NATIONAL ELECTRICAL CODE
Figure 1.
S2892A
1.
Read Instructions
–
Read all of the safety and operating
instructions before you operate this television.
2. Keep Instructions –Keep the safety and operating
instructions for future reference.
3. Heed Warnings –Adhere to all warnings on the appliance
and in the operating instructions.
4. Follow Instructions –Follow all operating and use
instructions.
5. Cleaning and Disinfecting –Unplug this TV from the wall
outlet before cleaning. Do not use liquid cleaners or aerosol
cleaners. Use a damp cloth for cleaning. Do not immerse this
TV in water. Exception: A product that is meant for
uninterrupted service and for some specific reason, such as
the possibility of the loss of an authorization code for a cable
TV converter, is not intended to be unplugged by the user for
cleaning or any other purpose, may exclude the reference to
unplugging the appliance in item 5.
6. Attachments–Do not use attachments not recommended by
the TV manufacturer. They may be hazardous.
7. Water and Moisture –Do not use this TV near water –for
example, near a bathtub, washbowl, kitchen sink, or laundry
tub, in a wet basement, or near a swimming pool, etc. Do not
use this TV outdoors.
8. Accessories –Do not place this TV on a cart, stand, tripod,
bracket, or table. The TV may fall, causing serious injury to a
child or adult and serious damage to the appliance. Use this
TV only with a mount recommended by the manufacturer, or
soldwiththeTV. Anymountingoftheapplianceshouldfollow
the manufacturer’s instructions and should use a mounting
accessory recommended by the manufacturer.
9. Ventilation –Slots and openings in the cabinet are provided
for ventilation, to ensure reliable operation of the TV, and to
protect it from overheating. Do not block or cover these
openings. Do not block the openings by placing the TV on a
bed, sofa, rug, or other similar surface. Do not place this TV
near or over a radiator or heat register. Do not place this TV
in a built-in installation such as a bookcase or rack.
10. Power Sources –Operate this TV only from the type of
power source indicated on the marking label. If you are not
sure of the type of power supplied to your health care facility,
consult your television dealer, facility maintenance, or local
power company.
11. Grounding –This TV incorporates a three-wire grounding-
type plug, a plug having a third (grounding) pin. This plug will
only fit into a grounding-type power outlet. This is a safety
feature. If you are unable to insert the plug into the outlet,
contact your electrician to replace your obsolete outlet. Do
not defeat the safety purpose of the grounding-type plug.
12. Power Cord Protection –Route power supply cords so that
they are not likely to be walked on or pinched by items placed
upon or against them, paying particular attention to cords at
plugs, convenience receptacles, and the point where they exit
from the appliance.
13. Outdoor Antenna Grounding –If you connect an outside
antenna or cable system to the TV, be sure the antenna or
cable system is grounded so as to prov ide some protection
against voltage surges and built-up static charges. Section
810 of the National Electrical Code, ANSI/NFPA No. 70,
provides information with respect to proper grounding of the
mastandsupportingstructure,groundingofthelead-inwireto
an antenna discharge unit, size of grounding conductors,
location of antenna discharge unit, connection to grounding
electrodes, and requirements for the grounding electrode.
(See Figure 1.)
IMPORTANT SAFETY INSTRUCTIONS

Communication
Systems Inc. MODEL PDI-Z13TV SERIES
13”ARM MOUNTED COLOR TV (WR) WIRED REMOTE Page 3of 5
Better Solutions Are Within Reach ™INSTALLATION & SAFETY INSTRUCTIONS
PDI Communication Systems, Inc. 40 Greenwood Lane Springboro, Ohio 45066 USA PH [phone] FX [phone]
PD 196-011 Rev 3
NOTE: When shipped from the factory, the TV/CATV menu option is set to the “CATV” (Cable Television) mode. If not using CATV, set this
menu option to “TV” mode.
PROGRAMMINGREMOTE
The TV is program-
med using the
IR remote
PD108-206-13B.
Install two “AAA”
batteries before use.
Programming buttons
menu, set -, set +,
and enter are used
to perform all TV
programming.
TO ADD/DELETE CHANNELS
Using the remote control.
1. Press the MENU button.
2. Press the SET + or–button until the
indicator next to “CH SET” begins to
flash, then press the ENTER button.
3. Press the SET + or–button until the
indicator next to “ADD/DELETE”
begins to flash, then press the ENTER
button.
4. Select the desired channels to be
added or deleted using the CH ?or
?button or the SET + or –button.
5. Press the ENTER button to alternately
ADD or DELETE. The channel
indicator will change colors. Red
indicates a deleted channel and Green
a memorized channel.
6. Press the MENU button three times
after adding or deleting the desired
channels, to return to normal TV
viewing.
TV/CATV SELECTION
Using the remote control.
1. Press the MENU button.
2. Press the SET + or–button until the
indicator next to “CH SET” begins to
flash, then press the ENTER button.
3. Press the SET + or–button until the
indicator next to “TV/CATV” begins to
flash.
4. Press the ENTER button to select the TV
or CATV mode. The arrow indicates the
selectedmode.
5. Press the MENU button twice to return to
normal TV viewing.
AUTOMATIC CHANNEL
MEMORY
Using the remote control.
1. Press the MENU button.
2. Press the SET+ or –button until the
indicator next to “CH SET” begins to
flash, then press the ENTER button.
3. Press the SET + or–button until
the indicator next to “AUTO CH
MEMORY” begins to flash, then
press the ENTER button. TheTV
will begin memorizing all the
channels available.
4. Press the MENU button twice to
return to normal TV viewing.
ADJUSTING PICTURE
Using the remote control.
1. Press the MENU button.
2. Press the SET + or–button until
the indicator next to “PICTURE”
begins to flash, then press the
ENTER button.
3. Press the ENTER button repeatedly
to select the item you want to
adjust.
4. Press the SET + or–button to
adjust the setting.
5. To return to initial settings press the
RESETbutton whilethepicture
adjusting mode appears on-screen.
CLOSEDCAPTIONING
ClosedCaptioning willdisplay texton screen
for hearing impaired viewers.
Closed Captions are accessed using the IR
remote control only.
Press the TV/CAP/TEXT button on the
remotecontrol toswitch betweennormal TV
and the two Closed Caption modes (captions
and ½ of full screen text).
PROGRAM THE TV
This TV is fitted with a V
-
CHIP which provides censored viewing and control access. The IR remote control is
necessary to enter the password.
ENABLE V-CHIP
1. Press the MENU button and press the SET+ or –button to select the V-CHIP SET option, then press the ENTER
button.
2. Enter your password (4 digits) using the remote control’s number buttons (0-9). In the event of entering incorrect
password press the RESET button. Then press the ENTER button.
3. Enter the same password for confirmation, then press the ENTER button.
4. Press the SET + or –button to select the V-CHIP option. Press the ENTER button to select the ON.
5. Press the SET + or –button to select the TV RATING or MOVIE RATING option. Press the ENTER button.
6. Press the SET + or –button to select the desired rating for the applicable video or TV channel. Press the ENTER
button.
7. Press the MENU button until the MENU screen is cleared.
WARNING:
A blue “PASSWORD” screen appears when a censored program is watched. If the password is not
entered, the persistent screen might permanently damage the picture tube leaving a ghost image. For hospital
operation, it is recommended that the V-CHIP NOT be enabled.
DISABLE V-CHIP
Deletes any stored password and disables the V-CHIP.
1. Turn the TV ON and adjust the volume to absolute minimum.
2. Press both Volume Down button on the set and Channel button (0) on the remote control for more than 1 second.
3. The standard menu screen will appear verifying that the V-Chip is disabled.
V
-
CHIP OPERATION

Communication
Systems Inc. MODEL PDI-Z13TV SERIES
13”ARM MOUNTED COLOR TV (WR) WIRED REMOTE Page 4of 5
Better Solutions Are Within Reach ™INSTALLATION & SAFETY INSTRUCTIONS
PDI Communication Systems, Inc. 40 Greenwood Lane Springboro, Ohio 45066 USA PH [phone] FX [phone]
PD 196-011 Rev 3
TV DEAD
•The TV is powered using an external power supply. Verify 28 VAC is being supplied on the coax.
•Power is OFF, check fuse or circuit breaker on external power supply.
•Coax is not connected. Check all coax connection including those in the nose and base of support arm.
TV SHUTS OFF
•Wrong Cable. Due to long cable runs encountered in hospital installations, coaxial cable employing a solid copper center
conductor and copper shield is required. Cable run lengths MUST NOT exceed 150 feet. Required coaxial cable numbers
include Alpha 9804C (non-plenum), Belden 9248 (non-plenum), West Penn 806 (non-plenum), or West Penn 25806 (plenum),
which have been tested with coax line-powered televisions. USE OF ANY OTHER CABLE NUMBER IS NOT RECOMMENDED.
•Sleep Timer is set.
•Power interrupted.
POOR RECEPTION
•Station or CATV experiencing problems, tune to another station.
•Make sure channels are set into memory.
•Check CATV connections.
•Check for sources of possible interference.
NORECEPTION
•Check all CATV cable connections.
•Set TV/CATV menu option to CATV mode.
NO RECEPTION ABOVE CHANNEL 13
•Make sure TV/CATV menu option is in the appropriate mode.
TROUBLESHOOTING
PDI-405C-22 PILF Support Arm
PDI-178CP Wall Bracket PDI-771CA Individual Wall Bracket Power Supply PD108-206-13B ProgrammingRemote
ACCESSORIES
PDI Communication Systems
40 Greenwood Lane
Springboro, Ohio 45066
Internet: http://www.pdiarm.com
Phone: [phone] Fax: [phone]
Engineering: [email protected]
Sales: [email protected]
CONTACT INFORMATION

Communication
Systems Inc. MODEL PDI-Z13TV SERIES
13”ARM MOUNTED COLOR TV (WR) WIRED REMOTE Page 5of 5
Better Solutions Are Within Reach ™INSTALLATION & SAFETY INSTRUCTIONS
PDI Communication Systems, Inc. 40 Greenwood Lane Springboro, Ohio 45066 USA PH [phone] FX [phone]
PD 196-011 Rev 3
The model PDI-Z13TV WR Series arm mounted television comes equipped with a pillow speaker interface. This model is specifically designed
to mount on the PDI-CEILING-MT-WR Ceiling Mount Arm but can also be mounted on the PDI-405 Wall Mounted Suspension Arm.
The PDI pillow speaker interface supports both digital or single
button pillow speakers.
Digital Pillow Speaker Supported TV Functions
1. Channel Up
2. Channel Down
3. ON/OFF
4. Mute
5. CC (Closed Captions)
Single Button Pillow Speaker Supported TV Functions
1. ON/OFF
2. Channel Up
Multi-Button Non-Digital Pillow Speaker TV Functions
1. NOT SUPPORTED
These instructions
assume you have successfully mounted the TV onto the suspension arm.
1. Identify the flat telephone style cable in the arm. Join the cable from the arm with a similar flat cable that exists
from the TV’s swivel.
2. Mount a 6P/6C modular jack box near the base of the arm.
3. A three-conductor interface cable should be wired between the modular jack box and bedside pillow speaker
jack. A pin-out is shown.
4. Connect the modular cable that exists
the base of the arm to the modular
jack box.
5. Connect a compatible pillow speaker
and test for TV sound and control.
NOTE: A single button pillow speaker operates the TV as follows:
•TV ON –Press the TV button once.
•CHANNEL UP –Press the TV button and release. The TV channels up.
•TV OFF –Press and HOLD down the TV button. The TV briefly channels up and then shuts off.
Wiring the Pillow Speaker
COMMON
DATA
CONNECTOR COLO
R CODE
Red Wire –Common
Black Wire –Sound
White Wire –Data
Supported TV Features
6P/6C Modular Jack Box
Mouser Electronics 154
-
3008 or similar
SOUND
Make Analog Digital Direct Access
Curbell 3103-001 3D0103096000ZM0-
001 D0108-A0Z-R0001
MedTek A1833-087 A1871-085T A1552-087D
A1871-087D
Crest XL031E0AXXXZ1N1
XL031E1AJ00Z1N1
XL031X0AXXXZ1N1
XL031X1AJ00Z1N1
NOTE: Compatibility of any other model pillow speaker not
guaranteed.
Compatible Pillow Speakers