Peacemounts Electronics MU0021 User manual

INSTALLATION GUIDE
Mantel Arm Mount
Support 55" to 100" Screens
Load Capacity: 40~154 lbs (18~70kg)
VESA 800x600 compatible
MU0021

7
2 of 9
Tools Needed for Assembly
WARNING
Table of Contents
Parts List ........................................................................................................................................................................ 3
Critical requirements of the installation . ... .......................................................................................................... 4
Installation of the bracket ........................................................................ ...................................................................
Installation of Screen & adjustment of the spring pressure ............................................................................................
5, 6
8
Product dimensions ........................................................................................................................................................
Maintenance instructions ................................................................................................................................................ 8
•
•
Be sure to read this entire manual thoroughly and you
•Sufficient expertise is required for installing of this product. Be sure to subcontract the installation to a qualified pe-
rson. Ensure special attention to safety is paid during installation. Tranquil mount is not liable for any damage or in-
jury caused by mishandling or improper installation, or by installing anything other than the specified product. Your
Statutory Rights, (if any) are not affected.
If the safety precautions are not observed or the product is used incorrectly, it may result to serious injury or dam-
age to your wall and TV.This instruction manual shows the correct handling of the product and important precauti-
ons necessary to prevent accident. Be sure to read this manual thoroughly and use the product correctly. Keep the
manual available for future reference.
•Ensure your hands and fingers stay clear from the adjustable moving mechanics at the back of the bracket. This is
to avoid your fingers getting trapped. Please supervise children when this product is in use.
•This product is supplied with small parts for installation. For your children’s safety please keep out of reach of chil-
dren at all times.
fully understand all the instructions and warning before
attempting to begin your installation.
Required Tools Optional Tools
3/16” 3/8”
Before you begin, please verify that all components are included and undamaged. If any parts are
missing or damaged, contact Product Supplier,Never proceed with missing or damaged parts!
Lay out all components and make sure you identify that each one has a match in the diagram.Some
of the parts included will not be used during installation.Do not proceed if you do not understand and
identify all of the components.
www.peacemounts.com
•This product should only be installed by someone who has a basic knowledge of buiding construction,installations and fully
understands these instructions.
•Make sure that the supporting surface will safely support the combined load of the mount, the display and all
attached hardware and components.
•This wall bracket will only supporting flat panel displays(LCD,Plasma).The maximum load capacity is 154 pounds.
•If mounting to a wall of wood stud construction, be sure that mounting bolt are anchored to the center of the studs
When installing the TV mount on a concrete wall, the wall must be at least 8"(203mm) thick with a minimum comp-
ressive strength from 2500 to 3000 psi (17.2 to 20.7 MPa),the concrete wall must meet ASTM C39. When installing
the TV mount on a cinder block wall, the cinder blocks must meet ASTM C216 specifications and have a minimum
nominal width of 8”(203mm). Be sure to mount in a solid part of the block, generally 1"(25 mm) minimum from the
side of the block.Do not drill into mortar joints! If plaster/drywall is thicker than 16mm,custom fasteners must be su-
pplied by the installer.
•Always have someone assist you to lift and position your equipment.
•T
•Screws must be tightly secured,but do not overtighten any screws (especially the four hex bolt screws M8x63.5mm)
or damage can occur and product may fail.
ighten screws and bolts firmly, but do not over tighten. Over tightening can damage the items and greatly reduce
their ability to hold. Please refer to suggested torque values where applicable in these instructions.

3 of 9
B
AA CC
DD EE
FF GG
K L M
A
C
2
BB
hook(x2)handle(x1)
plastic washer(x4)
Non-slip nuts(x4)
wallboard(x1)
front-panel(x1)connecting rod(x1) bracket(x1)
E
F
4
4
4
4
4
6
4
4
M8x25
M8x12
M6x25
M6x12
6.2x16x1.5
6.2x16x1.5
philips pan head screw
C
washer(1)
washer(1)
D
4
philips pan head screw
philips pan head screw
philips pan head screw
M6x8
philips pan head screw
2M6x25
M8x10
philips pan head screw
allen pan head screw
B4
H
J
K
L
4
G
17.0x9.0x14.0
spacer
N
M
M8x63.5
M10x60
M6
4
8.2x2.0x16
washer(2) 4
I
Hex bolt screw
Expansion pipe
Non-slip nuts
1 M10
spanner
1 M5
Hexagon wrench
2 L150
Cable ties
O2 M8
Hexagon wrench
with your product.
Parts may appear slightly different than illustrated.
Before you b egin, make sure all parts shown are included
Parts List
Description
A115x15x40
Wall panel cover(x2)
FG J
DIE
H
1
Hexagon wrench
M8(x2)
O
Spanner
M10(x1)
Hexagon wrench
M5(x1) Cable Ties(x2)
N
www.peacemounts.com

4 of 9
•Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and
components, Bracket installation need two people together to complete.
WARNING
CRITICAL requirements of the installation
Temperature at the front edge of mantle should
never exceed 110° F(43 ).
Mantle must not extend from mounting surface
more than 16 inches.
The space above the mantle must be taller than the wallboard. The required space
depends on how far out the mantle extends. Refer to chart below and add this
additional height to wallboard height to determine if space is tall enough.
If the main wall is wooden,There must be at least 2 studs
available for mounting.If the main wall is concrete or brick
wall,please refer to the S4 installation points. Mind you,
the wall covering must not exceed 5/8 inches thick.
TV weight must be between 40~154Ibs(18~70kg) and
have a screen size from 55” to 100”.Consult
Manual for verification.
TV Owner's
110°F
MAX.
16 inches
MAXIMUM
2 STUDS
(This two studs need along the
mantel center symmetric,and
the center distance between
two studs not more than 27.5”)
If mantle extends:
Less than 8 inches
8 - 11 inches
11 - 13 inches
13- 16 inches
This is required space height:
TV wallboard height plus 4 inches
TV wallboard height plus 5 inches
TV wallboard height plus 7 inches
TV wallboard height plus 8 inches
Wallboard height
Mantle
Extends
Space height
from 55” to 100”
12
3
5
4
WEIGHT:
40~154Ibs
(18~70kg)
C
L

5 of 9
Installation of the bracket
Measure the centerline of the mantle. Mark with tape on
the wall.
S1 S2
S4
Locate at least two studs with a stud finder. Locate the
center of these studs by using a sharp awl or finish nail
poked through the drywall to locate each edge. Lag bolts
must be installed into the CENTER of the studs.
C
L
C
L
Please reference point 5 at page 4 to punch, please
make sure that the four mounting holes don't have
too big deviation.
S3
Cutout shown
for reference
C
LC
L
C
L
C
L
C
L
6mm(3/16”)
CUTAWAY VIEW
INCORRECT
CORRECT
wall plate
plaster/
drywall
concrete
wall plate concrete
plaster/
drywall
C
L
10mm(3/8”)
M
Please reference point 5 at page 4 to p
unch,If the main
wall is concrete or brick wall,you must use the expansion
pipe we provided in M.
CL CL
CL
plywood wall wood stud wall
CL
CAUTION CAUTION
Do not drill into mortar joints!
10mm
(3/8”)
68mm
(2.7”)
6mm
(3/16”)
In order to have a better installa-
tion,it is necessary to inlay one
wire cassette on the wall.
68mm
(2.7”)

6 of 9
Installation of the bracket
Take out CC L/A from the packaging , please let the
pre-set wire go through the hole as illustrated in the picture.
Take out K/EE/FF/N(spanner M10) from the packaging ,
installation as illustrated in the picture.
S5 S6
Take out N/J from the packaging ,lock the four allen pan head screws(M8x10) with Hexagon wrench in N,then use cable ties
in N to tie up the wires,as is shown in the pictures below.
S7
A
(magentic spirit level)
CAUTION
Don't over tighten!
N
(spanner M10)
K
EE
keep the up direction uniform
L
L
CC
N
J
(Hexagon wrench)
(screw M8x10)
N
(Cable ties)

7 of 9
Installation of Screen & adjustment of the spring pressure
Select the parts from the packaging,and according to your
TV situation to choose B+F;or C+F+G;or D;or E+G,lock with
cross screwdriver.
Take out H/I/AA/DD from the packaging,according to the
size of the TV,adjust to the approriate location,as shown
in the picture below,then lock with cross screwdriver.
S8 S9
Lift the TV,through hooks for hanging onto the bracket panel,
then use a cross screwdriver to lock the two anti-off screws.
Take out GG from the packaging,buckle it to the wall plate.
S11
S10
GG
I
(screw M6x25)
H
(screw M6x8)
BB
G(C&E need G)
F
B/C (D&E don’t need F)

Increase the
constant force
Reduce the
constant force
Attention: The weight of the TV set in the weighing range
B: The TV sets up, turn to “ - ” until free hovering.
A: The TV sets can be hovering at any height, don not need to adjust.
C: The TV sets down, turn to “ + ” until free hovering.
Adjustable the bracket’s constant force
18.0/40.0
24.0/52.9
32.0/70.5
40.0/88.2
48.0/105.6
56.0/123.4
60.0/132.2
70.0/154.0
KG/LBS
STOP LINE
!
STOP LINE
!
According to different load weight,
please adjust the gas spring int o
suitable posi tion with in the scope
of the scale, excessive adjustme
nt
is forbidden!
ATTENTION
Refer to this
above cylinder
as a pointer
www.peacemounts.com
8 of 9
S12 Adjust the spring pressure to the appropriate level with the energy saving wrench or O(the hexagon
wrench M8 we provided).

Do not use strong acidic or alkaline liquid to wipe the product,
please use the cloth stained with water to wipe it.
Don’t disassemble the product randomly,
please contact the seller if there are any maintenance issues.
WARNING
mm042OTXAM
°51+~°3-:tlit
MAX820
mm0.016
mm7.638
0.82
0.001
°5±:level
°5±:level
swivel:±30°
mm8.004
from 150mm to 536mm
MAX127°
mm008OTXAM
PRODUCT DIMENSIONS
9 of 9 www.peacemounts.com
Table of contents
Popular Rack & Stand manuals by other brands

New Star
New Star NEOMOUNTS NM-D775DXSILVER instruction manual

OEM Tools
OEM Tools 24846 Operating instructions and parts manual

VOGELS
VOGELS TVB 2375 manual

Closet Maid
Closet Maid Rack Three-Tier 8024 installation instructions

Etec
Etec EXSM2455 installation guide

EZ Goal
EZ Goal 23318 installation instructions

Delta
Delta GAM-040 instruction manual

VOGELS
VOGELS EFA 8825 Mounting instructions

B-Tech
B-Tech Better By Design System X BT8370 Installation guide & parts list

New Star
New Star NEOMOUNTS NM-D335DBLACK instruction manual

Life Fitness
Life Fitness Optima Plus owner's manual

New Star
New Star TABLET-D150SILVER instruction manual