PEERLESS SmartMount SA770PU Guide

3215 W. North Ave. • Melrose Park, IL 60160 • [phone] or [phone] • Fax: [phone] • www.peerlessmounts.com
ISSUED: 05-16-08 SHEET #: 095-9285-1
Maximum UL Load Capacity: 200 lb (91 kg)
Models: SA770PU, SA770PU-S, RTFPA71U,
RTFPA71US, RTFPA71UI
Features:
•U-groove and U-cap system for clean and simple cable management
•Up to 7.75" total horizontal adjustment for ideal screen positioning
•+15°/-5° of easy one-touch tilt
•Two knockouts for optimal electrical access
•Three pivot points with up to 180° swivel
Installation and Assembly:
SmartMount®Articulating Flat Panel Wall Mounts for
37" to 71" screens
R
This product is UL Listed.
It must be installed by a
qualified professional
installer.
2

2 of 45 ISSUED:05-16-08 SHEET#:095-9285-1
Visit Peerless website at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870
Note: Read entire instruction sheet before you start installation and assembly.
Table of Contents
Parts List.......................................................................................................................................................................... 3, 4
Installation to Double Wood Stud Wall.................................................................................................................................. 6
Installation to Solid Concrete and Cinder Block .................................................................................................................... 7
Attaching Adapter Plate to Screen with VESA®Mounting Patterns .................................................................................... 13
InstallingandRemovalofFlatPanelScreen/AdjustmentofFlatPanelScreen ................................................................... 14
CableManagement ............................................................................................................................................................. 15
Tools Needed for Assembly
• studfinder ("edge toedge" stud finderis recommended)
• phillipsscrewdriver
• pencil
• drill
• 3/16" drill bit for wood studs, 5/16" drill bit for concrete
• 7/16" socket wrench or bit driver for wood screws
• level
• tapemeasure
• Donot begin toinstall your Peerlessproductuntil you haveread and understoodtheinstructions and warnings
containedin this InstallationSheet. If you haveany questions regardingany of the instructionsor warnings, please
callPeerlesscustomer care at 1-800-865-2112.
• This product should only be installed by someone of good mechanical aptitude, has experience with basic building
construction, and fully understands these instructions.
• Makesure that thesupporting surface willsafely support thecombined load ofthe equipment andall attached hard-
wareandcomponents.
• Neverexceed the Maximum ULLoad Capacity.Seepageone.
• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of an
"edgeto edge" studfinderis highly recommended.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tighten screwsfirmly, but donotovertighten.Overtightening can damage theitems,greatly reducing their holding
power.
• Thisproduct was designed andintendedto be mountedtothe following supporting surfacescheckedbelow with the
hardware included in this product as specified in the installation sheet.To mount this product to an alternative support-
ingsurface, contactPeerlesscustomercare at 1-800-865-2112.
• This product was designed to be installed on the following wall construction only;
WALLCONSTRUCTION ADDITIONALHARDWARE REQUIRED
xWoodStud None
xWoodBeam None
xSolidConcrete None
xCinderBlock None
MetalStud Do not attach except with Peerless accessory kit for metal studs;
Contact Customer Service for Peerless accessory kit for metal studs.
Brick ContactCustomerService
Otherorunsure? ContactCustomerService
WARNING

3 of 45 ISSUED:05-16-08 SHEET#:095-9285-1
Visit Peerless website at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870
N
A
CDFEGH J
OI
KL
M
R
P Q
B
with your product.
Parts may appear slightly different than illustrated.
Qty.
SA770PU,
RTFPA71U
SA770PU-S,
RTFPA71US, RTFPA71UI
Adouble arm 1 201-0276 201-0276-S 201-0276
Buniversal adapter bracket 1 201-P1573 201-C4573 201-P1573
Cscreen bracket 2 201-P1572 201-C4572 201-P1572
Dwall plate 1 201-0244 201-0244-S 201-0244
Eextension adapter bracket 4 201-P1574 201-C4574 201-P1574
Falligator® anchor 6 590-1025 590-1025 590-1025
GM10 x 15 mm socket screw 4 520-9262 520-9534 520-9262
HM5 x 10 mm flat head phillips screw 4 520-1573 520-2573 520-1573
I5/16-18 x 1.75" flat head socket screw 2 520-1332 520-2332 520-1332
J5/16"-18 nut 2 530-1034 530-2034 530-1034
K6 mm allen wrench 1 560-9716 560-9716 560-9716
L3/16" allen wrench 1 560-9713 560-9713 560-9713
M3 mm allen wrench 1 560-0073 560-0073 560-0073
N4 mm allen wrench 1 560-9646 560-9646 560-9646
Ocable ties 12 590-1168 590-1168 590-1168
PM10 x 15 mm phillips screw 4 520-1305 520-1305 520-1305
Q16 520-1023 520-1023 520-1023
R6 520-1243 520-2243 520-1243
Snovelty kit (not shown) 1- - 200-8570
5/16 x 3" wood screw
M5 x 6 mm phillips screw
Before you begin, make sure all parts shown are included
Parts List
Description

4 of 45 ISSUED:05-16-08 SHEET#:095-9285-1
Visit Peerless website at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870
Adapter Bracket Fasteners
M4 x 12 mm (6)
(504-9013)
M4 x 25 mm (4)
(504-1015)
M5 x 12 mm (4)
(520-1027) M5 x 25 mm (4)
(520-9543)
M8 x 16 mm (6)
(520-9257) M8 x 40 mm (4) (520-1136)
M8 x 25 mm (4)
(520-1031) I.D..34" (4)
(540-1059)
I.D..22" (4)
(540-1057)
M6 x 30 mm (4)
(510-9109)
M6 x 12 mm (4)
(520-1128) M6 x 25 mm (4)
(520-1208)
M6 x 20 mm (4)
(520-9402)
multi-washer(6)
(580-1036)
M4 x 20 mm (4)
(504-9020)BLK
(504-2020)SLV
M4 x 30 mm (4)
(520-1133)BLK
(520-2133)SLV
M6 x 20 mm (4)
(520-9402)BLK
(520-2402)SLV
M6 x 30 mm (4)
(510-9109)BLK
(510-2109)SLV
M6 x 40 mm (4)
(520-1584)BLK
(520-1207)SLV
ID.128"(4)
(590-5005)BLK
(590-5003)SLV

5 of 45 ISSUED:05-16-08 SHEET#:095-9285-1
Visit Peerless website at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870
NOTE: If mounting wall plate (D) to wood stud wall surface, slots on wall plate (D) must align to studs.
Determine desired location of screen center (refer to step 2) as shown in fig. 1.1, then hook arm onto wall plate (D)
as shown in fig. 1.2.
Using 3/16" allen wrench (L), secure arm (A) to wall plate (D) using two 5/16-18 x 1.75" flat head socket screws (I)
and two 5/16"-18 nuts (J) as shown in fig. 1.3. NOTE: BOTH 5/16-18 x 1.75" flat head socket screws (I) must be
fastened to wall plate securely using 5/16"-18 nuts (J). Do not adjust arm while screen is attached.
Adjustment of Arm on Wall Plate
1
fig. 1.1
fig. 1.3
fig. 1.2
A
D
J
I
A
D
CS = center of screen
Slots will align
on studs
A
D

6 of 45 ISSUED:05-16-08 SHEET#:095-9285-1
Visit Peerless website at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870
Installation to Double Wood Stud Wall
Determine and mark with a pencil, the desired center of screen on wall. Measure 7" (177 mm) above desired center
of screen and draw a horizontal line to locate placement of wall plate template. Wall plate (D) can be mounted to two
studs that are 16" apart. Use a stud finder to locate the edges of the studs. Use of an edge to edge stud finder is
highly recommended. Based on their edges, draw a vertical line down each stud’s center. Align top of template (top
of wall plate) with horizontal line and align slots of wall plate template with wood stud center lines. Level template
(wallplate) on wall and mark center of six mounting holes making sure that mounting holes are on the stud
centerlines. Drill six 3/16" (5mm) dia. pilot holes 3" (76 mm) deep. Level and secure wall plate (D) on wall using six
5/16" x 3" wood screws (R) as shown in fig. 2.2.
NOTE: Wall plate (slot) may be adjusted .875" in either direction off center of wood screw (R) and stud as shown in
detail 1.
Skip to step 3.
• Installermust verify thatthesupporting surface willsafelysupport the combinedloadof the equipmentandall attached
hardwareandcomponents.
• Tightenwood screws so thatwall plate is firmlyattached,but do notovertighten.Overtightening can damagethe
screws,greatlyreducing their holding power.
• Never tighten in excess of 80 in. • lb (9 N.M.).
• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder is
highlyrecommended.
• Hardwareprovided is for attachmentofmount through standard thicknessdrywallor plaster into woodstuds.Installers
areresponsibleto provide hardware for othertypesofmountingsituations.
WARNING
2
.875"
DETAIL 1
STUD
fig. 2.1
CS = center of screen
STUD
D
CS
7"
(177 mm)
R
D
fig. 2.2

7 of 45 ISSUED:05-16-08 SHEET#:095-9285-1
Visit Peerless website at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870
Installation to Solid Concrete or Cinder Block
Determine and mark with a pencil, the desired center of
screenon wall. Measure7" (177 mm)above desired center
of screen and draw a horizontal line to locate placement of
wall plate template.Align top of template (top of wall plate)
withhorizontal line. Leveltemplate (wallplate) onwalland
mark center of six mounting holes. Drill six 5/16" (8 mm)
dia. holes 3" (76.2 mm) deep. Insert anchors (F) in holes
flushwith wall as shown (right).Place wall plate(D) over
anchors and secure with six 5/16" x 3" screws (R) as
shown in fig. 2.3. Level wall plate, then tighten all fasteners.
• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete
thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid
part of the block, generally 1" minimum from the side of the block. Cinder block must meetASTM C-90 specifications.
It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to avoid
breakingout the backofthe hole whenenteringa void orcavity.
• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.
• Makesure that thesupporting surface willsafely support thecombined load ofthe equipment andall attached hard-
wareandcomponents.
WARNING
CUTAWAYVIEW
INCORRECT
concrete
surface
1
3
2
F
Drill holes and insert anchors (F).
CORRECT
Place wall plate (D) over anchors (F) and secure with
screws (R).
Tighten all fasteners.
wallplate
plaster/
drywall
concrete wallplate concrete
plaster/
drywall
• Always attach concrete anchors directly to load-
bearingconcrete.
• Neverattachconcreteanchorsto concrete covered
withplaster,drywall, or otherfinishingmaterial. If
mountingtoconcrete surfaces covered withafinishing
surfaceisunavoidable, the finishing surfacemustbe
counterboredasshown below. Be sureconcrete
anchorsdo not pull awayfromconcrete when tighten-
ing screws. If plaster/drywall is thicker than 5/8",
custom fasteners must be supplied by installer (not
evaluatedbyUL).
WARNING
D
F
R
2
cinder block
fig. 2.3
• Tighten screws so that wall plate is firmly attached,
butdonotovertighten.Overtighteningcandamage
screws,greatlyreducing their holding power.
• Never tighten in excess of 80 in. • lb (9 N.M.).
WARNING
D
R
F
solid concrete

8 of 45 ISSUED:05-16-08 SHEET#:095-9285-1
Visit Peerless website at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870
H
C
B
GLIDERS
Remove two M5 x 20 mm screws from the rollbrake. Lift
adapter plate out from tilt bracket as shown.
NOTE: M5 X 25 mm screw may need to be loosened a
fewturns to allowadapter bracket tobe removed using
4mm allen wrench (N).
3
Fasten two screen brackets (C) to the gliders on universal adapter bracket (B)using four M5 x 10 mm flat head
phillips screws (H) as shown in fig. 4.1.
4-1
NOTE: If your screen has a VESA hole pattern skip to page 13.
Using the hole pattern shown in detail 2, attach the adapter plate to universal adapter
bracket (B) or dedicated adapter plate with four M10 x 15 mm screws (G) as shown.
Tighten screws using 6 mm allen wrench (K).
4
Installing Universal Adapter Bracket to Screen
ADAPTER
PLATE
ROLLBRAKE
TILT
BRACKET
M5 X 20 MM
SCREW
A
M5 X 25 MM
SCREW
HOLE PATTERN
FOR USE WITH
UNIVERSAL
ADAPTER
BRACKET OR
DEDICATED
ADAPTER PLATE
DETAIL 2
LARGE
HOLES
ADAPTERPLATE
DEDICATED
ADAPTERPLATE
G
G
ADAPTERPLATE
B
fig. 4.1

9 of 45 ISSUED:05-16-08 SHEET#:095-9285-1
Visit Peerless website at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870
4-2 The universal adapter bracket has two fixed stop positions
which lock the extension brackets in the retracted position
(shown right) or extended position (shown below) using the
M5 x 9mm screws.
If the distance between mounting holes on the back of your screen
measure 17.5" (445mm) wideor lesskeep universaladapter
bracket in the retracted position. Skip to step 4-4.
If the distance between mounting holes on the back of your screen
measure wider than 17.5" (445 mm), remove four M5 x 9 mm
socketbutton head screwsfrom universal adapterbracket using
3 mm allen wrench (M), as shown below. NOTE: You may need to
loosen four M5 x 9 mm vertical support screws, as shown in
detail 3, one full turn to adjust extension brackets. Extend both
extension brackets out to the fixed stop positions (threaded hole
shownin reverse viewbelow). Secure extensionbracket to the
horizontal support by fully tightening M5 x 9 mm socket button
head screws into the fixed stop positions of the extension brackets
using 3 mm allen wrench (M) as shown in the reverse view.
Retighten M5 x 9 mm vertical support screws as shown in detail 3.
• Do not tighten screws with excessive force. Overtightening can cause damage to mount. Tighten M5 x 9 mm vertical
support screws and M5 x 9mm socket button head screws to 35 in. • lb (3.95 N.M.) maximum torque.
CAUTION
DETAIL 3
LOOSENVERTICALSUPPORT
SCREWSFOREXTENSION
BRACKETADJUSTMENT
THENTIGHTEN
VERTICAL
SUPPORT
HORIZONTAL
SUPPORT
EXTENSION
BRACKET
HORIZONTAL
SUPPORT
EXTENDED
POSITION
M5X 9 MM BUTTON
SOCKETHEADSCREW
HORIZONTAL
SUPPORT
RETRACTED
POSITION
RETRACTED
FIXEDSTOP
POSITION
REVERSE
VIEW
FIXEDSTOPPOSITION
(THREADEDHOLE)
EXTENSION
BRACKET

10 of 45 ISSUED:05-16-08 SHEET#:095-9285-1
Visit Peerless website at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870
Attach extension adapter bracket (E) to screen bracket (C) using four M5 x 6 mm phillips
screws (Q) for each bracket as shown.
Attaching Extension Adapter Bracket (optional)
4-3
E
E
Q
Q
C
CUNIVERSALADAPTERBRACKET

11 of 45 ISSUED:05-16-08 SHEET#:095-9285-1
Visit Peerless website at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870
NOTE:Refertopage9foradjustmentsofuniversaladapterbracket(B)extensionbrackets.
To prevent scratching the screen, set a cloth on a flat, level surface that will support the weight of the screen. Place
screenfaceside down.Refertoscreenmanufacturersinstructionsforremovalofknobs,base, cover,orscrew(s)onthe
back of the screen to prepare for mounting screen brackets (C) to screen.Adjust screen brackets (C) to align with
screen mounting holes as shown in fig. 4.5. Select the small, medium, large or extra large screws from the baffled
fastener pack then attach screen brackets (C) to screen following figure 4.6 or 4.7 on page 12. Retighten M5 x 16 mm
glider screws as shown in fig. 4.4.
NOTE:Top and bottommountingholes must beusedfor attachingscreenbrackets.Middle holes should alsobeused
wherethefastenersand screens allow.Verifythat all holes are properlyaligned,andthentightenscrews using a phillips
screwdriver.
NOTE: For flat back screens proceed to step 4-6. For bump-out or recessed back screen skip to step 4-7
4-5
NOTES:
• Always use multi-washers when attaching
screen brackets (C) to your screen when using
small, medium or large screws. No multi-washer
is required for extra large (M8) screws.
• Use the corresponding hole in the multi-washer
that matches your screw size as shown.
MULTI-WASHER
MEDIUMHOLEFORM5SCREWS
LARGEHOLEFORM6SCREWS
SMALLHOLEFORM4SCREWS
Using 3 mm allen wrench (M), loosen screws
ofeach glider ontheuniversal adapter bracket
untilscreen brackets (C)can movewith ease
within extension bracket.
fig. 4.4
4-4
M5X 16 MM SOCKET
BUTTONHEAD SCREW
GLIDER
C
M5X 16 MM SOCKET
BUTTONHEAD SCREW
GLIDER
CENTERSCREENBRACKETS(C)VERTICALLYONBACKOFSCREEN
SCREEN
X
X
C
B
YY
"Y" dimensions should be equal.
fig. 4.5 NOTE: "X"dimensionsshould be equal.
• Tighten screws so screen brackets are firmly attached to screen. Do not tighten with excessive force.
Overtighteningcan cause stress damagetoscrews, greatly reducingtheirholding power and possiblycausing
screw heads to become detached. Tighten to 40 in. • lb (4.5 N.M.) maximum torque.
• If screws don't get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly
secured, damage may occur to screen or product may fail.
WARNING

12 of 45 ISSUED:05-16-08 SHEET#:095-9285-1
Visit Peerless website at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870
Begin with the shortest length screw, hand thread screw through multi-washer and screen brackets (C) into screen
as shown below. Screw must make at least three full turns into the mounting hole and fit snug into place. Do not
over tighten. If screw cannot make three full turns into the screen, select a longer length screw from the baffled
fastenerpack. Repeat forremaining mounting holes,level screen bracketsand tighten screws. Snap bracketcovers
into the back of screen brackets (C), refer to fig. 4.1 on page 8.
NOTE: Spacersmaynot be used,depending upon thetype of screen.
Ifyouhaveanyquestions,pleasecallPeerlesscustomercareat1-800-865-2112.Visit our website at
www.peerlessmounts.com/unltodeterminethecorrect fasteners to use foryourparticularscreen.
Begin with longer length screw, hand thread screw through multi-washer, screenbrackets(C) and spacer in that
order into screen as shown below. Screw must make at least three full turns into the mounting hole and fit snug into
place. Do not over tighten. If screw cannot make three full turns into the screen, select a longer length screw from
thebaffled fastener pack.Repeat for remainingmounting holes, levelscreen brackets andtighten screws. Snap
bracket covers into the back of screen brackets (C), refer to fig. 4.1 on page 8.
Ifyouhaveanyquestions,pleasecallPeerlesscustomercareat1-800-865-2112. Visitourwebsiteat
www.peerlessmounts.com/unltodeterminethecorrect fasteners to use foryourparticularscreen.
For Flat Back Screen
For Bump-out or Recessed Back Screen
SCREEN
MULTI-WASHER
SCREW
fig 4.7
SPACER
SCREEN fig 4.6
MULTI-WASHER
SCREW
4-6
4-7
C
C

13 of 45 ISSUED:05-16-08 SHEET#:095-9285-1
Visit Peerless website at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870
Attaching Adapter Plate to Screen with VESA®Mounting Pattern
4
Mounting Patterns
VESA®200 x 100 VESA®200 x 200
VESA®100 x 100
VESA®200 x 100 VESA®200 x 200
VESA®100 x 100
Choosehole pattern as shown indetail4for VESAmountingpattern.Begin with theshortestlengthscrew, hand thread
through adapter plate into screen as shown in detail 5. Screw must make at least three full turns into the mounting hole
and fit snug into place. Do not over tighten. If screw cannot make three full turns into the screen, select a longer length
screwfromthefastenerpack.Repeatforremainingmounting holes.Securelytightenscrews.
NOTE:Spacersmaynotbeused,dependinguponthe type ofscreen.
Ifyouhaveanyquestions,pleasecallPeerlesscustomercareat1-800-865-2112.Visitourwebsiteat
www.peerlessmounts.com/unl todeterminethecorrect fasteners to useforyourparticularscreen.
NOTE: For screens with a hole
pattern in a pocket,
spacers go between
adapter plate and
screen.
ADAPTER
PLATE
SCREEN
DETAIL 4
DETAIL 5

14 of 45 ISSUED:05-16-08 SHEET#:095-9285-1
Visit Peerless website at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870
To attach screen to arm (A), insert the puck of adapter
plate into the tilt bracket slot as shown in figure 5.1.
Attach brake pad assembly as shown in Detail 5 so that
the brake pad is snug against the adapter plate. Adjust
roll position of adapter plate to level screen then lock puck
in place by tightening M5 x 25 mm screw on the
underside of tilt bracket using 4 mm allen wrench (N).
Tighten all (M5 x 20 mm, M5 x 25 mm) screws.
NOTE:Toremove screenfromarm(A),removetwo
M5 x 20 mm screws and brake pad. Lift screen out of tilt
bracket.
5
Installing and Removing Flat Panel Screen
Adjustment of Flat Panel Screen
TENSION
KNOB
M5 X 25 MM
SCREW
BOTTOM
VIEW
6
• Do not lift more weight than you can handle. Use additional man power or mechanical lifting equipment to safely
handleplacementof the screen.
• Failure to lock brake pad with two M5 x 20 mm screws and lock tilt bracket with M5 x 25 mm screw can cause
screen to come off mount if hit accidentally.
WARNING
fig. 5.1
DETAIL 5
ADAPTERPLATE
BRAKEPAD
TILT
BRACKET
M5 X 20 MM SCREW (QTY. 2)
M5X 25 MM SCREW
A
PUCK
FORPORTRAITORLANDSCAPESCREENORIENTATION:
Remove two M5 x 20 mm screws and brake pad. Lift screen
out of tilt bracket. Rotate screen into portrait or landscape
position. Insert adapter plate puck into the tilt bracket slot as
shown in fig. 5.1. Attach brake pad to tilt bracket using two
M5 x 20 mm screws as shown in Detail 5. Tighten all
(M5 x 20 mm, M5 x 25 mm) screws.
TILT Adjustment: Adjust tension knob on side of mount to
desired tension to enable tilt adjustment and balance your
screen size and weight. Push or pull from top or bottom of
screen to adjust tilt as shown. The tilt can be adjusted to a
maximumof 10° forwardor 5° backward.Retightentension
knob.
ROLL Adjustment: Rotate screen either5° clockwise or
counter-clockwise, level screen then tighten M5 x 25 mm
screw using 4 mm allen wrench (N) as shown in bottom view.
• Donottighten screws with excessiveforce.Overtightening
can cause damage to mount. Tighten M5 x 20 mm screws
to 20 in. • lb (2.26 N.M.) maximum torque.
CAUTION
• Do not tighten screws with excessive force.
• Becareful not to pinchfingerswhen opening andclosing
mountfrom the wall.
CAUTION

15 of 45 ISSUED:05-16-08 SHEET#:095-9285-1
Visit Peerless website at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870
Cable Management
NOTE: Makesure cables haveenough slack toallow full movementof the arm.
Runpower cablethrough top orbottom of arm(A) and signalcable(s) through otherside of armin order toavoid
interference with the signal. Lock cables into place by snapping cable covers onto mount. Screen may have to be
movedfor easy access.
Optional: If additional cable management is required use cable ties (O) as shown in detail 7.
fig. 7.1
7
O
A
DETAIL 7
©2008,PeerlessIndustries,Inc.Allrightsreserved.
Allotherbrandandproductnamesaretrademarksorregisteredtrademarksoftheirrespectiveowners.
CABLEMANAGEMENT COVER
CABLE
DETAIL 6
SLOT CABLE

3215 W. North Ave. • Melrose Park, IL 60160 • [phone] or [phone] • Fax: [phone] • www.peerlessmounts.com
ISSUED: 05-16-08 SHEET #: 095-9285-1
Características:
•Sistema de estría y cubierta en U para un manejo elegante y sencillo de los cables
•Hasta 7.75" de ajuste horizontal total para colocar la pantalla en la posición ideal.
•Fácil ajuste de +15°/-5° de la inclinación con un solo toque
•Dos tapas semiperforadas removibles para un óptimo acceso eléctrico
•Tres puntos de giro con una rotación de hasta 180°
Instalación y ensamblaje:
Soportes de pared de brazo articulador para pantallas
planas de 37" a 71" - SmartMount®
R
Este producto lleva la
marca de UL
(Underwriters
Laboratory). Debe ser
instalado por un
instalador profesional
calificado.
Máxima capacidad de carga UL: 200 lb (91 kg)
Modelos: SA770PU, SA770PU-S, RTFPA71U,
RTFPA71US, RTFPA71UI

17 of 45 ISSUED: 05-16-08 SHEET #: 095-9285-1
Español
Visite el sitio Web de Peerless en www.peerlessmounts.com Para el Servicio al cliente llame al 1-800-729-0307 ó 708-865-8870
Nota: Lea la hoja de instrucciones completa antes de comenzar la instalación y el ensamblaje.
Tabla de contenido
Lista de piezas ............................................................................................................................................................. 18,19
Instalaciónenunaparedconmontantesdemaderadobles................................................................................................ 21
Instalación en una pared de concreto macizo o de bloques de hormigón de escorias ........................................................ 22
Fijación de la placa adaptadora a pantallas con configuraciones de montaje VESA® ........................................................ 28
Instalación y desinstalación de la pantalla plana/Ajuste de la pantalla plana...................................................................... 29
Manejo de los cables .......................................................................................................................................................... 30
Herramientas necesarias para
el ensamblaje
•localizadorde montantes (serecomienda
unode“bordeaborde”)
•destornilladorphillips
•lápiz
• taladro
• No comience a instalar su producto de Peerless hasta haber leído y entendido las instrucciones y las advertencias
contenidas en la Hoja de Instalación. Si tiene alguna pregunta acerca de cualquiera de las instrucciones o las
advertencias,porfavor,llameaServicioalCliente de Peerless al 1-800-865-2112.
• Esteproducto sólo debeserinstalado por una personaque tenga una aptitudmecánica,que tenga experienciaen
construcción básica de edificios y que entienda estas instrucciones en su totalidad.
• Asegúrese de que la superficie de apoyo sostendrá, con seguridad, la carga combinada del equipo y todos los
fijadoresycomponentes.
• NuncasobrepaselacapacidadmáximadesoportarcargaaceptadaporUnderwritersLaboratories.(Vealapágina 16).
• Si va a instalar el producto en una pared con montantes de madera, asegúrese de que los tornillos de montaje estén
anclados en el centro de los montantes. Se recomienda utilizar un localizador de montantes de “borde a borde”.
• Siempre cuente con la ayuda de un asistente o utilice un equipo mecánico de izar para levantar y colocar el equipo
conmás seguridad.
• Apriete los tornillos con firmeza, pero no en exceso.Apretarlos en exceso puede dañar los artículos y puede
disminuirsignificativamentesufuerza de fijación.
• Este producto fue diseñado con la intención de que se instale en las superficies de apoyo marcadas abajo con los
accesorios de instalación incluidos en este producto como se especifica en la hoja de instalación. Para instalar este
productoenotra superficie de apoyo,llamea Servicio al ClientedePeerlessal 1-800-865-2112.
• Esteproducto fue diseñadoparaser instalado enparedescon la siguienteconstrucciónsolamente:
CONSTRUCCIÓNDELAPARED ACCESORIOSADICIONALES NECESARIOS
xMontantedemadera Ninguno
xVigademadera Ninguno
xConcretomacizo Ninguno
xBloquedehormigón de escorias Ninguno
Montantede metal No lo instale excepto con el juego de accesorios de Peerless para
montantes de metal.
Llame a Servicio al Cliente para pedir el juego de accesorios de
Peerless para montantes de metal.
Ladrillo ComuníqueseconServicioalCliente.
¿Otrasuperficie o no estáseguro? ComuníqueseconServicioalCliente.
ADVERTENCIA
• broca de 3/16" para montantes de madera, broca de 5/16"
paraconcreto
• llavede copa 7/16"o destornillador depuntas
intercambiablesde tornillos paramadera
•nivel
•cinta métrica

18 of 45 ISSUED: 05-16-08 SHEET #: 095-9285-1
Español
Visite el sitio Web de Peerless en www.peerlessmounts.com Para el Servicio al cliente llame al 1-800-729-0307 ó 708-865-8870
A
Las piezas pueden verse un poco distintas a la ilustración.
Cantidad
SA770PU,
RTFPA71U
SA770PU-S,
RTFPA71US, RTFPA71UI
A
brazo dobl
e
1 201-027
6
201-0276-
S
201-027
6
Bsoporte adaptador universal 1 201-P1573 201-C4573 201-P1573
Csoporte de la pantalla 2 201-P1572 201-c4572 201-P1572
Dplaca de pared 1 201-0244 201-0244-S 201-0244
E4 201-P1574 201-C4574 201-P1574
F6 590-1025 590-1025 590-1025
Gtornillo de cabeza hueca M10 x 15 mm 4 520-9262 520-9534 520-9262
H4 520-1573 520-2573 520-1573
I2 520-1332 520-2332 520-1332
Jtuerca de 5/16”-18 2 530-1034 530-2034 530-1034
Kllave allen de 6 mm 1 560-9716 560-9716 560-9716
Lllave allen de 3/16” 1 560-9713 560-9713 560-9713
M1 560-0073 560-0073 560-0073
Nllave allen de 4 mm 1 560-9646 560-9646 560-9646
Osujetacables 12 590-1168 590-1168 590-1168
Ptornillo phillips M10 x 15 mm 4 520-1305 520-1305 520-1305
Q16 520-1023 520-1023 520-1023
R6 520-1243 520-2243 520-1243
SJuego de artículos innovadores
(no mostrado)
1 - - 200-8570
llave allen de 3 mm
anclaje alligator®
tornillo para madera de 5/16 x 3"
tornillo de cabeza hueca plana de 5/16 -
18 x 1.75”
tornillo phillips M5 x 6 mm
Antes de comenzar, asegúrese de que su producto contiene todas
las piezas que se muestran.
soporte adaptador de extensión
Lista de piezas
Descripción
tornillo phillips de cabeza plana
M5 x 10 mm
N
C FE GH J
OI
KL
M
R
P Q
B
D

19 of 45 ISSUED: 05-16-08 SHEET #: 095-9285-1
Español
Visite el sitio Web de Peerless en www.peerlessmounts.com Para el Servicio al cliente llame al 1-800-729-0307 ó 708-865-8870
Fijaciones para los soportes adaptadores
M4 x 12 mm (6)
(504-9013)
M4 x 25 mm (4)
(504-1015)
M5 x 12 mm (4)
(520-1027) M5 x 25 mm (4)
(520-9543)
M8 x 16 mm (6)
(520-9257) M8 x 40 mm (4) (520-1136)
M8 x 25 mm (4)
(520-1031) diámetrointerior.34" (4)
(540-1059)
diámetrointerior .22" (4)
(540-1057)
M6 x 30 mm (4)
(510-9109)
M6 x 12 mm (4)
(520-1128) M6 x 25 mm (4)
(520-1208)
M6 x 20 mm (4)
(520-9402)
arandelamúltiple(6)
(580-1036)
M4 x 20 mm (4)
(504-9020)
NEGRO
(504-2020)
PLATEADO
M4 x 30 mm (4)
(520-1133)
NEGRO
(520-2133)
PLATEADO
M6 x 20 mm (4)
(520-9402)
NEGRO
(520-2407)
PLATEADO
M6 x 30 mm (4)
(510-9109)
NEGRO
(510-2109)
PLATEADO
M6 x 40 mm (4)
(520-1584)
NEGRO
(520-1207)
PLATEADO
ID.128"(4)
(590-5005)
NEGRO
(590-5003)
PLATEADO

20 of 45 ISSUED: 05-16-08 SHEET #: 095-9285-1
Español
Visite el sitio Web de Peerless en www.peerlessmounts.com Para el Servicio al cliente llame al 1-800-729-0307 ó 708-865-8870
NOTA: Si la placa de pared (D) se va a instalar en la superficie de una pared con montantes de madera, las ranuras
de la placa de pared (D) se tienen que alinear con los montantes.
Señale el punto donde quiere que quede el centro de la pantalla (como se maestro en paso 2), como se muestra en
la figura 1.1, y enganche el brazo a la placa de pared (D), como se muestra en la figura 1.2.
Con una llave allen de 3/16" (L), fije el brazo (A) a la placa de pared (D) utilizando dos tornillos de cabeza hueca
plana de 5/16-18 x 1.75" (I) y dos tuercas de 5/16"-18 (J), como se muestra en la figura 1.3. NOTA: AMBOS
tornillos de cabeza hueca plana de 5/16-18 x 1.75" (I) tienen que estar fijados con firmeza a la placa de
pared con las tuercas de 5/16"-18 (J). No ajuste el brazo si la pantalla ya se ha fijado al mismo.
Ajuste del brazo en la placa de pared
1
fig. 1.1
fig. 1.3
fig. 1.2
A
D
J
I
A
D
CP = centro de la pantalla
Las ranuras se
alinearán con los
montantes
A
D