PEN+GEAR C227-B User manual

16-Sheet
Cross-Cut
Shredder
Operation Manual
Model
C227-B
pen+
I'GEAR
cLUs
Please
read
thoroughly
before
operating this equipment
Before
using the shredder, please read this manual and become familiar with the safety information,
operating instructions, and
maintenance
requirements.
Following all warnings and
instructions
inthis
manual
and
as
marked
on
the shredder.
Do
not
attempt
to
service
this
unit
by yourself. Doing
so
will
avoid the manufacturer's warranty and
may
expose
you
to
sharp cutting blades and/or high voltage electric shock
that
could
cause
serious
injury. Any
repairs must be performed by qualified
service
personnel.
IMPORTANT
safety
measures
1.
Please read the manual before operating the
machine
hair orother small items away from the feed
Keep all loose
articles
of
clothing, ties
2.
opening
to
prevent injury.
3. Keep in the OFF position when the shredder is
not
in
use
for
prolonged periods of time.
4. Do
not
place hands
or
fingersinto the shredder throat
as
serious injury could result.
5. Always
turn
off
or
unplug the
shredder
prior
to
moving, cleaning
or
emptying
the
wastebasket.
6. Empty wastebasket frequently.
7. The
document
shredder
must
always be deactivated and disconnected
from
the
electrical
line
prior
to
moving, transporting and cleaning
the
device and prior
to
emptying the
waste
basket.
V.0

or
pets
are
Please do not leave the document shredder unattended e.g. in the
event
children
8.
nearby.
9. The device may not be operated with
a
damaged power cord.
10. For indoor
use
only.
11.
This machine is
no
toy. Keep it away from children
and
pets.
12. To protect the machine well,
we
suggest the
user
to
operate it in this way: work 30 minutes then rest
20 mins.
13. Please do
not
spray any flammable gas
or
oil onto
this
shredder,
it
may
cause
fire.
14. The machine allowed
max
shred 16 sheets/1 Creditcard
or
1
CDat
one
time.
15. The socket-outlet must be installed
near
the equipment and must be easily accessible during
operation.
16. Hazardous Moving Parts. Keep Fingers and Other Body Parts Away.
Setting
up
the document shredder:
Ensure that the bin is
not
pulled
out.
1.
Connect the main plug
to
a
standard 120V volt AC socket.
Starting
the
shredder:
The sliding switch is located
on
the top side of
the
unit and
can
be set
to
four
(4) positions
1. AUTO position:
2.
The shredding operation
starts
automatically
as
soon
as
the
paper
to
be shredded is inserted into the
feed slot,the"POWER" indicator light
turns
green.
After the shredding operation is complete, the
device
will
automatically deactivate.
REV position:
Rectifying
a
paper jam. In this
case,
the direction of the shredding operation is reversed before the
work
cycle ends in order
to
free the shredding blades. The "POWER"
indicator
light
turns
green.
Should
you
determine
that
too
much paper has been inserted and the shredding operation slows noticeably,
immediately
set
the
switch
to
this
position, also in the
event
paper
is accidentally inserted.
2.
3. OFF position:
In order
to
empty the
waste
basket
or
in the
event
the device is
not
used
for
a
prolonged period of time,
set
the switch
to
OFF and disconnect the device from the electrical line in order
to
avoid the risk
or
injuries. The indicator light switches off.
4. Forward(FWD):
Machine will forward when switch
at
this position, The "POWER" indicator light
turns
green.

Overloading:
If
you
overload
more
than
16 sheet
paper
in
one
time, the overload
indicator
will
turn
on,
the
machine
will be
reverse
automatically, then
remove
any
excess
paper. The
overload
indicator
turn
off, The
machine
will
then
be
reset
to
either
normal
or
standby mode.
Bin Full:
If the Full basket indicator
turn
to
red,he
cutter
will stop immediately. Should this happen, then please
pull
out
the bin and dispose
the
paper
shreds,and place bin back in. The machine will then be
reset
to
either normal
or
standby
mode.
Set up:
1.
Unpack
the
shredder.
Place
the
shredder upright
on
a
level surface.
2. Make
sure
the
waste
bin is properly inserted into
the
shredder cabinet.
3. Plug the
power
cord
into
a
standard (120V )outlet. Do
not
use
an
extension cord.
Troubleshooting
Troubleshooting Resolution
Error
Is
the
power
supply and
socket
connected
to
the
wall correctly?Adjust
the
connections.
Is
the
collection
unit
positioned
correctly?Adjust
the
position
of
the
collection
unit.
Replace
the
power
cable
or
call product
Support 1-844-728-6918.
Is
the
power
cable
damaged?
Equipment is
not
functioning
Is
the
engine possibly overheating?
Is
the
"overheat"
indicator
light
turn
on?
Wait
until
the
machine
has
cooled
down.
Is
the
sheet
of
papertoo
thin
for
it
to
be
detected
by
the
sensors?Fold
the
sheets
of
paper.
Do
you
want
to
shred
many
pieces
of
paper
in
one
go?
Reduce
the
amount
of
paper
and try again.
Push
the
switch
to
REV
position
and
remove
any
excess
paper.
Is
the
paper
jammed?
Is
the
"overload"
indicator
light
turn
on?
Cutter
is
blocked
Excess
paper
or
unusual
objects
are
blocking the
sensors?
Remove
any
excess
paper and try again.
Cutter
will
not
stop
Is
the
surface
uneven?
Is
the
Machine
sounds
too
loud Place
the
equipment
on
a
flat
surface.
equipment in
a
straight position?
Should the
instructions
above
not
help
to
resolve
the issue,
then
please
contact
our
product
support
1-
844-728-6918

Protection against paper jams and overheating:
The C227-B is equipped with a
motor
overheat
guard.
To
protect
the
machine well,
we
suggest the
user
to
operate it in this way:
work
30
minutes
then 20 minutes off. Under the following conditions, the
current
feed
to
the unit's
motor
is interrupted:
Continual operation of the shredder withmaximum capacity
for
a
prolonged period of time, e.g. longer
1.
than 30 minutes without interruption.
2. Overrunning the shredding capacity e.g. adding
more
than 16 sheets of
paper
(75g) in
one
operation
or
in the
event
the paper is
not
inserted length-wise
into
the feed slot.
Under the above-mentioned conditions, the automatic overheat guard of the
motor
is triggered,
whereupon the
current
feed
to
the device is interrupted. In such
a
case,
please take the followingsteps
Disconnect the main plug from the AC socket in
order
to
avoid the risk of serious injuries and wait
at
1.
least 20 minutes until the overheat guard has
reset.
Now
tear
off
excess
paper
from
the top of the shredder
or
remove
it.
2.
paper away from the shredding blades. Afterwards,
set
the
switch back
to
the AUTO position. If
necessary,
repeat this step.
3.
Reconnect the main plug
to
the AC socket and
set
the switch
to
the
REV position. Pull the remaining
With the switch in the AUTO position and the
open
feed slot,
you
may
now
continue
the normal
shredding process. Shredder stops while shredding
Overloading:
If you overload
more
than 16 sheet
paper
in
one
time, the machine
will
be
reverse
automatically, then
remove
any
excess
paper.
The machine
will
then be
reset
to
either normal
or
standby mode.
Bin Full:
If the Bin Full indicator
turn
to
red,the
cutter
will stop immediately. Should this happen,
then
please pull
out
the bin and dispose the
paper
shreds,and place bin back
in.
The
machine
will
then
be
reset
to
either
normal
or
standby mode.
Attention:
This model includes
a
built-in safety interlock mechanism which is located
on
the
front
of the shredder.
THE SHREDDER WILL NOT OPERATE WHEN THE BIN IS PULLED OUT!
Never
shred envelopes (any window,
insulated
or
with glued flaps),adhesive materials(labels,decals/stickers
or
glued paper), newsprint,
transparencies, laminated documents, continuous forms, cardboard,
or
hard and plastic materials
(except credit cards).
Technical specification:
Voltage:
Power:
Paperentrywidth:
Shred
size
Shredpapercapacity:
Shredspeed:
Dimension:
120V-,60Hz
360W
220mm
4*35mm
16
sheets
/
1Credit
Card/
1CD
1.6m/min
354243*522mm

FCC
statement:
This device complies with part 15
of
the FCC Rules. Operation is subject
to
the following
two
conditions:
(1) This device may
not
cause
harmful interference, and (2) this device
must
accept any interference
received, including
interference
that
may
cause
undesired operation.
Changes
or
modifications
not
expressly approved by the party responsible for compliance could
void
the user's authority
to
operate the equipment.
NOTE: This equipment has been tested and found
to
comply with the limits for
a
Class Bdigital device,
pursuant
to
part 15
of
the FCC Rules. These limits
are
designed
to
provide
reasonable
protection against
harmful
interference
in
a
residential installation. This equipment generates,
uses
and
can
radiate radio
frequency
energy
and,
if
not
installed
and used in accordance with the instructions,
may
cause
harmful
interference
to
radio
communications.
However, there is
no
guarantee that interference
will
not
occur
in
aparticular
installation.
If
this
equipment does
cause
harmful
interference
to
radio
or
television reception,
which
can
be
determined
by turning
the
equipment
off
and
on,
the
user
is encouraged
to
try
to
correct
the
interference
by
one
or
more
of
the
following
measures:
-Reorient
or
relocate
the
receiving
antenna.
-Increase
the
separation
between
the
equipment and
receiver.
-Connect
the
equipment
into
an
outlet
on
a
circuit
different
from
that
to
which the receiver is connected.
-Consult
the
dealer
or
an
experienced radio/TV technician
for
help.