Pentagram horNET Wi-Fi PCI 11g User manual

Installation and Operation Manual
PENTAGRAM horNET
Wi-Fi PCI 11g (P6121-L4)
Wi-Fi USB 11g (P6122-12)
The latest versions of manual, drivers and applications are available on
www.pentagram.eu
2008-04-08

NOTE! Any information and technical data are subject to change without prior notification
and/or indication in this manual.
© 2008 PENTAGRAM
All rights reserved; copying and reproduction is strictly forbidden.

horNET P6121-L4 / P6122-12
3
INDEX
INTRODUCTION......................................................................................................5
PACKAGE CONTENTS.......................................................................................5
BEFORE YOU BEGIN .........................................................................................5
OVERVIEW ..............................................................................................................6
PCI ADAPTER.....................................................................................................6
USB ADAPTER....................................................................................................6
INSTALL WIRELESS ADAPTER..............................................................................7
PCI ADAPTER.....................................................................................................7
USB ADAPTER....................................................................................................7
INSTALL DRIVER AND UTILITY.........................................................................8
WIRELESS ADAPTER CONFIGURATION ..............................................................9
RAUI APPLICATION............................................................................................9
PROFILE TAB....................................................................................................10
NETWORK TAB.................................................................................................17
ADVANCED TAB...............................................................................................20
STATISTICS TAB ..............................................................................................21
WMM TAB..........................................................................................................22
WPS TAB...........................................................................................................23
RADIO ON/OFF TAB.........................................................................................25
ABOUT TAB.......................................................................................................25
HELP TAB..........................................................................................................25
TROUBLESHOOTING............................................................................................26
SPECIFICATIONS..................................................................................................27

horNET P6121-L4 / P6122-12
4

horNET P6121-L4 / P6122-12
5
Introduction
Pentagram horNET wireless network adapter is a powerful 32-bit PCI/USB Adapter that
installs quickly and easily into PCs. The Adapter can be used in Ad-Hoc mode to connect
directly with other cards for peer-to-peer file sharing or in Infrastructure mode to connect with a
wireless access point or router for access to the Internet in your office or home network.
Pentagram horNET wireless PCI/USB adapter connects you with 802.11g networks at up to a
54Mbps. And for added versatility, it can also interoperate with all the up to 11Mbps 802.11b
products found in homes, businesses, and public wireless hotspots around the country. And in
either mode, your wireless communications are protected by industrial-strength WPA, so your
data stays secure.
This Manual contains information on how to install and configure your wireless adapter to get
your network started accessing the Internet. It will guide you through the correct configuration
steps to get your device up and running.
Package Contents
1. Wireless PCI (P 6122-12) / USB (P 6121-L4) adapter
2. Manual, Drivers and Utility on CD
3. Quick Installation Guide
4. External RP-SMA antenna (only P 6122-12)
If any of the above items are missing, please contact your reseller.
Before you begin
You must have at least the following:
•A laptop computer/desktop PC with an available 32-bit PCI/USB slot
•At least a 300MHz processor and 32MB of memory
•Windows 98SE, ME, 2000, XP
•A CD-ROM Drive
•PCI/USB controller properly installed and working in the laptop computer
•An 802.11g or 802.11b Access Point (for infrastructure Mode) or another 802.11g or
802.11b wireless adapter (for Ad-Hoc; Peer-to-Peer networking mode.)

horNET P6121-L4 / P6122-12
6
Overview
PCI adapter
The status LED indicators of the PCI wireless adapter are described in the following.
LED State Action
LNK Lit Connected
ACT Blinking Searching for wireless network / Data transfer
USB adapter
The status LED indicators of the PCI wireless adapter are described in the following.
LED State Action
LNK/ACT Blinking Searching for wireless network / Data transfer

horNET P6121-L4 / P6122-12
7
Install Wireless Adapter
PCI Adapter
1. Open your PC case and locate an available PCI on the motherboard.
2. Slide the PCI Adapter into the PCI slot. Make sure that all of its pins are touching the
slot’s contacts. You may have to apply a bit of pressure to slide the adapter all the way in.
after the adapter is firmly in place, secure its fastening Tab to your PC’s chassis with a
mounting screw. Then close your PC.
3. Attach the external antenna to the adapter’s antenna port.
4. Power on the PC.
5. If the Found New Hardware Wizard displays, click Cancel button and follow instructions
in next section.
USB Adapter
1. Power on your PC, let the operating system boot up completely, and log in as needed.
2. Hold the adapter and insert it into a USB slot.
3. If the Found New Hardware Wizard displays, click Cancel button and follow instructions
in next section.

horNET P6121-L4 / P6122-12
8
Install Driver and Utility
1. Insert the Driver and Utility CD-ROM into the CD-ROM driver.
2. The Wizard should run automatically, and menu showed below should appear. If it does
not, click the Start button and choose Run. In the field that appears, enter x:\autorun.exe
(where xis the letter of your CD-ROM drive).
1. Select Install Pentagram horNET, to start driver installation.
2. Select I accept the terms of the license agreement and click Next >.
3. If you want to use attached application software (recommended), select Ralink
Configuration Tool and click Next >. If you want to use application software built in
operation system, select Microsoft Zero Configuration Tool and click Next >.
4. Select Optimize for WiFi mode and click Next > for compatibility. Select Optimize for
performance mode and click Next > for performance. Second option may cause
incompatibilities with some wireless devices – if that’s the case, uncheck Enable Tx
Burst option on Advanced Tab in attached application software.
5. Click Install, to install drivers and application.
6. In some cases there is a need to restart computer after driver installation. Select Yes, I
want to restart my computer now., to restart computer after installation or No, I will
restart my computer later. if you plan to restart computer at later time.
7. Click Finish, to complete installation process.

horNET P6121-L4 / P6122-12
9
Wireless adapter configuration
A configuration application is installed with adapter drivers. The application’s icon is displayed
in the system tray (next to the clock), and its appearance depends on the adapter and/or
connection status.
The adapter is not attached
to the PC or RF is off. The adapter is not connected to a wireless
network.
The adapter is connected to
a wireless network.
To launch the adapter’s configuration application, double-click the application’s icon (RaUI).
RaUI application
RaUI application window is divided into three parts:
1. Tab bar – click on Tab to display its contents in the main pane. Active Tab is highlighted.
Use arrow buttons to scroll Tab bar.
2. Main pane – this pane displays contents of selected Tab.
3. Secondary pane – this pane contains connection information or additional options for
selected in main pane option. Click More ( ) button to show secondary pane or
Less ( ) button to hide it.
Connection information contains:
Status – Connection status:
•RF OFF – Adapter disconnected or RF is turned off.

horNET P6121-L4 / P6122-12
10
•Disconnected – Wireless connection not esTablished.
•[SSID] <--> [BSSID] – Connection esTablished to network with displayed ID’s.
Extra Info – Additional information about connection.
Channel – Channel (frequency) used by wireless network.
Authentication – Authentication method used by wireless network.
Encryption – Encryption method used by wireless network.
Network Type:
•Ad hoc – Connection point-point (peer-to-peer) with other wireless adapter.
•Infrastructure – Connection with wireless network via AP (Access Point) or wireless
router.
Status – Wireless connection status.
IP Address – IP Address configured or obtained from DHCP server.
Sub Mask – Subnet Mask configured or obtained from DHCP server.
Default Gateway – Gateway IP address configured or obtained from DHCP server.
Link Quality: Shows link quality as a percentage bar (0-100%).
Signal Strength: Shows signal strength as a percentage bar (0-100%).
Noise Level: Shows noise level as a percentage bar (0-100%).
Transmit / Receive – Transmit / receive parameters for active network.
Profile Tab
This Tab allows you to create profiles for the most frequently used wireless networks, i.e.
home network, company network or public hotspots. The profiles can be activated as required.
Profile List – This list contains configured profiles. First column contains profile name, second
– network SSID and third – additional network information. Icons on the list means:
Connection with activated profile esTablished successfully
Connection with activated profile not esTablished
Infrastructure Type network
Ad hoc Type network
Secured network
Selected profile information is displayed on the right side of the list.
Add: Click Add to create a new profile. Profile configuration is opened in secondary pane.
Edit: Click Edit to change settings for the selected profile. Profile configuration is opened in
secondary pane.
Delete: Click Delete to delete the selected profile.
Activate: Click Activate to activate the selected profile.

horNET P6121-L4 / P6122-12
11
Profile configuration – System Config Tab
This Tab allows configuration of basic connection parameters.
Profile Name – Enter a name to identify your profile. Default PROFx.
SSID – Enter a network service set identifier (SSID) or select from a list of active networks. If
SSID Broadcast function of AP is disabled, SSID must be entered by hand. SSID is case
sensitive, which means that pentagram and Pentagram are two different networks.
Network Type – You can select two wireless network types.
•The Infrastructure mode supports communications between a wireless network and
a wired network using an access point.
•The Ad hoc mode supports peer-to-peer communications between two wireless network
devices (without using an access point).
TX Power – Set the signal transmit power to be used by the radio transmitter. Choose the
appropriate value from the drop-down list.
Preamble – Select the preamble length, i.e. Auto, Long or Short.
Channel – Select the channel to be used when esTablishing an Ad hoc network.
PSM – Select the power saving mode.
•Using CAM (Constantly Awake Mode), the network adapter will operate at full power
when connected to mains.
•Using PSM (Power Saving Mode), the network adapter will enter power saving mode.
RTS Threshold – Use the slider or enter a value for the RTS threshold in the field provided.
Default value: 2347.
Fragment Threshold – Use the slider or enter a value for the fragment threshold in the field
provided. Default value: 2346.
OK – Closes profile configuration and saves settings.
Cancel – Closes profile configuration without saving settings.

horNET P6121-L4 / P6122-12
12
Profile configuration – Auth. \ Encry. Tab
This Tab contains all Authentication and Encryption settings
Authentication:
•Open – With the Open method, every wireless station can request authentication.
•Shared – With Shared authentication, the station requesting authentication must provide
a secret key (which can be obtained from the network administrator) using a secure
channel (independent of the 802.11 wireless communications channel).
•LEAP – (Light Extensible Authentication Protocol) is an EAP authentication method used
primarily on Cisco Aironet wireless networks. This protocol encrypts transmitted data
using dynamically generated WEP keys, and supports two-way authentication.
•WPA and WPA2 – IEEE 802.1x protocol is used for authentication and AES or TKIP for
encryption.
•WPA PSK and WPA2 PSK – Station requesting authentication must provide a WPA
Preshared Key. AES or TKIP are used for encryption.
•Authentication: Open and Shared
Authentication – Change authentication method.
Encryption – Select None or WEP.
802.1X – Check this option to use IEEE 802.1x for authentication. IEEE 802.1x supports
full user authentication and control. This will also enable 8021X Tab, where 802.1x can
be configured.
WEP Key / Key#1 ... 4 – When you select WEP encryption or Shared authentication
without 802.1x, you need to enter a correct WEP key.
•If a 64-bit WEP key is used, enter 10 Hexadecimal characters or 5 ASCII
characters.
•If a 128-bit WEP key is used, enter 26 Hexadecimal characters or 13 ASCII
characters.
Show Password – Select this box if you do not want key characters to be replaced with
asterisks.
OK – Closes profile configuration and saves settings.
Cancel – Closes profile configuration without saving settings.

horNET P6121-L4 / P6122-12
13
•Authentication: LEAP
Authentication – Change authentication method.
Identity – Enter your identity for the LEAP authentication service.
Password – Enter your password for the LEAP authentication service.
Domain Name – Enter your domain name for the LEAP authentication service.
Show Password – Select this box if you do not want key characters to be replaced with
asterisks.
OK – Closes profile configuration and saves settings.
Cancel – Closes profile configuration without saving settings.
•Authentication: WPA and WPA2
Authentication – Change authentication method.
Encryption – Select the encryption method to be used.
•AES (Advanced Encryption System) uses symmetrical 128-bit data block
encryption.
•TKIP (Temporal Key Integrity Protocol) uses stronger encryption algorithms and
MIC (Message Integrity Check) to provide security against hackers.
WPA and WPA2 use IEEE 802.1x protocol for authentication. After selecting encryption
method go to 8021X Tab, where 802.1x settings can be configured.
OK – Closes profile configuration and saves settings.
Cancel – Closes profile configuration without saving settings.

horNET P6121-L4 / P6122-12
14
•Authentication: WPA PSK and WPA2 PSK
Authentication – Change authentication method.
Encryption – Select the encryption method to be used.
•AES (Advanced Encryption System) uses symmetrical 128-bit data block
encryption.
•TKIP (Temporal Key Integrity Protocol) uses stronger encryption algorithms and
MIC (Message Integrity Check) to provide security against hackers.
WPA Preshared Key – Enter the WPA preshared key (WPA-PSK and WPA2-PSK only).
The key should be 8 to 32 characters in length.
Show Password – Select this box if you do not want key characters to be replaced with
asterisks.
OK – Closes profile configuration and saves settings.
Cancel – Closes profile configuration without saving settings.
Profile configuration – 8021X Tab
Settings on this Tab allow to configure IEEE 802.1x protocol. All information can be obtained
from wireless network administrator. Appearance of this Tab depends on options selected
from EAP Method and Tunnel Authentication lists.
•PEAP – Protect Extensible Authentication Protocol. PEAP transport securely
authentication data by using tunneling between PEAP clients and an authentication
server. PEAP can authenticate wireless LAN clients using only server-side certificates,
thus simplifying the implementation and administration of a secure wireless LAN.
•TLS/Smart Card – Transport Layer Security. Provides for certificate-based and mutual
authentication of the client and the network. It relies on client-side and server-side
certificates to perform authentication and can be used to dynamically generate user-
based and session-based WEP keys to secure subsequent communications between the
WLAN client and the access point.
•TTLS – Tunneled Transport Layer Security. This security method provides for certificate-
based, mutual authentication of the client and network through an encrypted channel.
Unlike EAP-TLS, EAP-TTLS requires only server-side certificates.
•EAP-FAST – Flexible Authentication via Secure Tunneling. It was developed by Cisco.
Instead of using a certificate, mutual authentication is achieved by means of a PAC
(Protected Access Credential) which can be managed dynamically by the authentication
server. The PAC can be provisioned (distributed one time) to the client either manually or
automatically. Manual provisioning is delivery to the client via disk or a secured network
distribution method. Automatic provisioning is an in-band, over the air, distribution. For
tunnel authentication, only support "Generic Token Card" authentication now.
•MD5-Challenge – Message Digest Challenge. Challenge is an EAP authentication type
that provides base-level EAP support. It provides for only one-way authentication - there
is no mutual authentication of wireless client and the network.

horNET P6121-L4 / P6122-12
15
•ID \ PASSWORD Tab
EAP Method – Change EAP authentication method.
Tunnel Authentication – Change tunnel authentication method.
Session Resumption – Enable / disable session resumption.
Authentication ID / Password – Identity, Password and Domain Name for server.
Only EAP-FAST authentication can key in domain name. Domain name can be keyed in
blank space.
Tunnel ID / Password:
•Identity – Identity for tunnel.
•Password – Password for tunnel.
Show Password – Select this box if you do not want key characters to be replaced with
asterisks.
Password Mode – Select password mode: Static Password or Soft Token).
OK – Closes profile configuration and saves settings.
Cancel – Closes profile configuration without saving settings.
•Client Certification Tab
Use Client certificate – Enable this option to use Client certificate for server
authentication and then select certificate from drop-down list. You can find detailed
information on certificate below this list.
OK – Closes profile configuration and saves settings.
Cancel – Closes profile configuration without saving settings.

horNET P6121-L4 / P6122-12
16
•Server Certification Tab
Use certificate chain – Enable this option, to enable the certification feature and select
the certificate issuer.
Allow intermediate certificates – Select this option to allow the use of intermediate
certificates. These certificates must be located on the certification chain between the
server certificate and the server selected from list.
Server name – Enter the name of the authentication server.
OK – Closes profile configuration and saves settings.
Cancel – Closes profile configuration without saving settings.
•EAP Fast Tab
Allow unauthenticated provision mode – During the PAC can be provisioned
(distributed one time) to the client automatically. It only supported Allow
unauthenticated provision mode and use EAP-MSCHAP v2 authentication to
authenticate now. It causes to continue with the esTablishment of the inner tunnel even
though it is made with an unknown server.
Use protected authentication credential – During the PAC can be provisioned to the
client manually via disk or a secured network distribution method. Click Import, to
browse for PAC settings file or click Remove, to stop using current file.
File Path – Path, where PAC settings file is located.
OK – Closes profile configuration and saves settings.
Cancel – Closes profile configuration without saving settings.

horNET P6121-L4 / P6122-12
17
Network Tab
This Tab enables searching for and connecting to active wireless networks.
Icons on list means:
Connection to this network esTablished successfully
Connection to this network not esTablished
Infrastructure type network
Ad hoc type network
802.11 standards supported by wireless station
Secured network
Show dBm – Select this box, to show signal Strength on AP List as dBm instead of
percentages. This also applies to Signal Strength and Noise Strength in secondary pane.
AP List – List of wireless networks in range. Columns contains as follows: SSID (hidden when
SSID Broadcast on AP is disabled), network type icon (Infrastructure or Ad hoc) and used
channel, supported 802.11 standards (i.e. 802.11g), security and signal strength. Double-click
on network, to display Detailed network information in secondary pane.
Rescan – Click this button to rescan for available wireless networks.
Add to Profile – Click to create a profile for selected network. You can find detailed
information on profile configuration in previous section.
Connect – Click to connect do selected network without creating a profile. Connection
configuration will be displayed in secondary pane. Options correspond to options from profile
configuration. You can find detailed information on profile configuration in previous section. If
selected network doesn’t broadcast SSID, after clicking Connect button you will be asked to
enter SSID. Enter SSID in Please enter SSID field in secondary pane and click OK, to
continue connection configuration.

horNET P6121-L4 / P6122-12
18
Detailed network information
•General Tab
General info on network and security.
SSID – Network SSID or Hidden if AP doesn’t broadcast SSID.
MAC Address – MAC address of AP.
Authentication Type – Authentication used by this network.
Encryption Type – Encryption used by this network.
Channel – Channel and frequency used by this network.
Network Type – Infrastructure or Ad hoc.
Beacon Interval – Interval for sending beacon to sustain connection.
Close – Close information.
•WPS Tab
Information on WPS (Wi-Fi Protected Setup).
Authentication Type – There are three types of authentication modes supported by
RaConfig. They are open, Shared, WPA-PSK and WPA system.
Encryption Type – For open and shared authentication mode, the selection of
encryption type are None and WEP. For WPA, WPA2, WPA-PSK and WPA2-PSK
authentication mode, the encryption type supports both TKIP and AES.
Config Methods – Correspond to the methods the AP supports as an Enrollee for
adding external Registrars. (a bitwise OR of values)
Value Hardware Interface
0x0001 USBA (Flash Drive)
0x0002 Ethernet
0x0004 Label

horNET P6121-L4 / P6122-12
19
0x0008 Display
0x0010 External NFC Token
0x0020 Integrated NFC Token
0x0040 NFC Interface
0x0080 Push Button
0x0100 Keypad
Device Password ID – Indicate the method or identifies the specific password that the
selected Registrar intends to use. AP in PBC mode must indicate 0x0004 within two-
minute Walk Time.
Value Description
0x0000 Default (PIN)
0x0001 User-specified
0x0002 Rekey
0x0003 Display
0x0004 PushButton (PBC)
0x0005 Registrar-specified
0x0006-0x000F Reserved
Selected Registrar – Indicate if the user has recently activated a Registrar to add an
Enrollee. The values are TRUE and FALSE.
State – The current configuration state on AP. The values are Unconfigured
and Configured.
Version – WPS specified version.
AP Setup Locked – Indicate if AP has entered a setup locked state.
UUID-E – The universally unique identifier (UUID) element generated by the Enrollee.
There is a value. It is 16 bytes.
RF Bands – Indicate all RF bands available on the AP. A dual-band AP must provide it.
The values are 2.4GHz and 5GHz.
Close – Close information.
•CCX Tab
Information regarding CCX (Cisco Compatible eXtensions) support by AP.

horNET P6121-L4 / P6122-12
20
Advanced Tab
This Tab can be used to change advanced wireless network adapter options.
Wireless mode – Select wireless stations to which the adapter can connect: 802.11 B/G mix
(802.11b and 802.11g stations) or 802.11 B only (802.11b stations only).
Wireless Protection – AUTO (STA will dynamically change as AP announcement), ON
(Always send frame with protection) or OFF (Always send frame without protection).
TxRate – Allows the transmit rate to be changed manually. Default value: Auto.
Enable TX BURST – Selecting this mode may accelerate frame transmission.
Enable TCP Window Size – Selecting this feature may improve TCP performance on
wireless connections.
Fast Roaming – Switchover between access points will occur when the current access point’s
minimum signal strength threshold set in this field is exceeded.
Show Authentication Status Dialog – When you connect AP with authentication, choose
whether show Authentication Status Dialog or not. Authentication Status Dialog displays the
process about 802.1x authentication.
Select Your Country Region Code – The item selected in this field determines the channels
(frequencies) available.
Enable CCX (Cisco Compatible eXtensions) – This enables support for Cisco Compatible
Extensions.:
•Turn on CCKM – Using LEAP allows taking advantage of CCKM (Cisco Centralized Key
Management).
•Enable Radio Measurement – Enables support for the Radio Measurement feature
used in Cisco network hardware.
Apply – Applies changes.