Philex 28074R User manual

75MM
75MM
75MM 75MM
100MM
100MM
100MM 100MM
COMPATIBILITY CHECKER
VESA 50
Fittings
VESA 75
Fittings
VESA 100
Fittings
VESA 200 x 100 Fittings
This TV bracket is designed to t LCD TV’s and computer monitors with VESA 50, VESA 75, VESA
100, VESA 200x100 and VESA 200 bracket ttings. These standard ttings are found on almost all
systems typically up to 32” diagonal screen size although some may vary - in which case you may
need to contact the TV manufacturer for assistance.
The weight capacity of this bracket is 20kg in order for the tilting mechanism to maintain secure.
To check if your TV or monitor is compliant, look at the back of your system and check it has four
equally spaced mounting holes spaced in any of the combinations shown.
TILT & SWIVEL ARM LCD TV MOUNT
Part No. 28074R
Installation Instructions
WARNING!!!!
Correct assembly is essential
This mount should be tted to a solid wood, brick or concrete wall
Note: We have not supplied wall xings with this product. All walls differ in strength and
thickness. We advise that you consult professional personell for guidance for purchasing
screws designed specically for your type of wall.
turn over for installation instructions...
VESA 200
Fittings

Customer Careline: 0901 293 0038
Calls are charged at £1 per minute from a BT landline. Call charges from other networks may vary
Support: http://technical.philex.com
STEP ONE
WALL FITTING FOR WOOD STRUCTURE (eg STUD WALLING)
Due to the width of wooden beams within dividing walls, there is a limitation for the distance between wall mounting
screws. This LCD wall mount has central wall mounting holes for this purpose. Fit three suitable wall screws to your wall
(please seek professional advise before obtaining and tting wall screws - all walls differ!), Fit the screws in the mounting
holes as shown below (along the middle of the bracket).
STEP TWO - ASSEMBLING THE TV MOUNTING SECTION
Fit the TV mounting plate to the tillting clamp as shown below. The knob should not be fully tightened until the installation
has been completed and the tilting angle of the television has been nalised.
WALL FITTING FOR CONCRETE/BRICK WALLS
Fit three suitable wall screws to your wall (please seek professional advise before obtaining and tting wall screws - all
walls differ!), Fit the screws in the mounting holes shown below
BRICK/CONCRETE WALLING STUD WALLING
Note: wall xings not supplied

Customer Careline: 0901 293 0038
Calls are charged at £1 per minute from a BT landline. Call charges from other networks may vary
Support: http://technical.philex.com
STEP FOUR- FITTING THE TV MOUNTING PLATE
TO THE BRACKET ARM
Fit the TV mounting plate to the bracket arm as shown
below. Tighten the nut to secure the position. Finally t
the dome caps to the screw head and nut to nish the
installation. Position the TV in the tilting angle required
and tighten the nut holding the TV mounting plate the tilt-
ing clamp.
STEP THREE- FITTING THE TV MOUNTING PLATE
Once you have checked the compatibility of your
television, locate the tting holes on the mounting plate
that match your televisions mounting holes.
Check which type of the supplied tting screws t your
television (M4 or M5 - supplied) and attach the plate
rmly to the back of your television.
STEP FIVE - CABLE MANAGEMENT
This LCD wall mount is supplied with a plastic outer casing. This outer casing allows you to route and hide your power
and other cables along the arm of the mount. Before you t the outer casing, run your cables along the arm and secure
to the arm using tape. Use a knife or scizzors or cut out routing holes in the plastic to allow the cables to pass through.
There are sections of plastic which have been made thinner to allow for easy cutting
Note: TV not shown on mount for illustration purposes
v3