Philips FWT6600 User manual

all
TABLE OF CONTENTS Page
Technical specification ...........................................................1-16
Safety instruction......................................................................2-1
ESD protection..........................................................................2-4
Set Block diagram ....................................................................3-1
Set Wiring diagram...................................................................4-1
Disassembly diagram...............................................................5-1
Main board
Circuit diagram........................................................................6-1
Layout diagram.......................................................................6-2
Display board
Circuit diagram........................................................................7-1
Layout diagram.......................................................................7-2
CD board
Circuit diagram........................................................................8-1
Layout diagram.......................................................................8-2
MCU board
Circuit diagram........................................................................9-1
Layout diagram.......................................................................9-2
Tuner board
Circuit diagram......................................................................11-1
Layout diagram.....................................................................11-2
AMP board
Circuit diagram....................................................10-1..10-2..10-3
Layout diagram.............................................................10-4..10-5
Mechanical Exploded view......................................................12-1
©Copyright 2013 Philips Consumer Electronics B.V. Eindhoven, The Netherlands
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or
transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise without
the prior permission of Philips.
Published by LX 1 Service Audio Printed in The Netherlands Subject to modification
Version 1.0
Mini Hi-Fi System FWT6600/
317 3140 038 60220
All manuals and user guides at all-guides.com
all-guides.com

1-2
Type /Versions:
Features
Board in used: Service policy
Main BOARD
Display BOARD
* TIPS : C -- Component Lever Repair.
M -- Module Lever Repair
√
-- Used
Feature diffrence
RDS
VOLTAGE SELECTOR
ECO STANDBY - DARK
Type /Versions:
FWM6600
VERSION VARIATION
Amp BOARD
Key BOARD
(LATAM)
Mic BOARD
MCU BOARD
FWM6600
/55
Tuner BOARD
CD BOARD
/55
Location of PC Boards
Technical Specification and Connection Facilities
C/M
C/M
C/M
C/M
C/M
C/M
(ARGENTINA)
x/77 x/78
x/77 x/78
(BRAZIL)
SMPS BOARD M
C/M
C/M
C/M
C/M
C/M
C/M
C/M
C/M
C/M
C/M
C/M
C/M
C/M
C/M
M M
C/M
C/M
C/M
C/M
C/M
C/M
CD PART
Amp Board SMPS Board
EQ Board
MIC/PC IN/AUDIO IN Board
MCU Board
BT Board
USB Board
Display Board
Light Board
Key Board
Main Board
Tuner Board
CD Board
AC Cord
All manuals and user guides at all-guides.com

No. Descrpitopn Page
 *(1(5$/3$57)52173$11(/63(&,&),&$7,21 
 *(1(5$/3$57%$&.3$11(/63(&,&),&$7,21 
 *(1(5$/3$57*(1(5$/63(&,&),&$7,21 
 *(1(5$/3$577(&+1,&$/63(&,&),&$7,21 
 *(1(5$/3$57,32'6,*1$63(&,&),&$7,21 
 *(1(5$/3$57$8',26,*1$/63(&,&),&$7,21 
 *(1(5$/3$57&/2&.7,0(563(&,&),&$7,21 
 *(1(5$/3$5786%6,*1$/63(&,&),&$7,21 
 *(1(5$/3$57781(563(&,&),&$7,21$OO 
 *(1(5$/3$57&'0363(&,&),&$7,21 
 *(1(5$/3$579(56,2129(59,(:63(&,&),&$7,21 
FWT6600 SH 190 Contact List
1-3
All manuals and user guides at all-guides.com

1-4
26
4
5
Pos
1
2
3
8
DEPICTION
9
10
11
12
6
7
MAX SOUND
27
17
18
19
20
21
22
13
14
MIC 1 JACK
15
16
23
24
25
IR LENS
AUX/LINE
TUNER
DISC3
OPEN/CLOSE
>||(PLAY/PAUSE)
|<TITLE PRESET
Description
DISC2
Page
DISC CHANGE
DISC1
TITLE>|PRESET
DISPLAY
PROGRAM/TIMER
DBB
VAC
OTPIMAL
MIC VOL
ROCK
MIC2 JACK
LINE IN
USB JACK
JAZZ
USB RECORD
ECHO VOL
TECHNO
NAME : A411 1 SH 190 - 1
Issued DateVer
1
FWT6600/ All Version
2
3
Remark :
Class No
23-Sep-11
POWER ON/OF
<<ALBUM--SEARCH.TUNING
35
31
32
33
27
28
DISC
IS
MODE34
STOP
USB JACK
38
36
37
29
30
1 used into
Units in Dealercarton
Remarks :
GENERAL PART 1 - FRONT PANNEL SPECICFICATION
LIGHT
USB DEL
Diemensions with Boxes ( wxhxd ) 265mm X 382mm X 345mm
USB
Weight ( exclusive packing & batery )26KG
Finshing : Chrome Plate
VFD DISPLAY
Material : HIPS / ABS / POM / V2 / SAN
39
CABINET
Diemensions without Boxes ( wxhxd ) 1250mm X 340mm X 495
Weight ( inclusive packing )8.505KG
VOL
Units in Masstercarton
ALBUM>>SERCH.TUNING
KT CHECK: DATE :
All manuals and user guides at all-guides.com

1-5
1 F.M. Anntena
2
27
25
26
23
24
22
17
18
19
20
21
14
15
16
11
12
13
7FAN
LOW /HIGH Left / Right Speaker Socket8
9
10
DEPICTION Pos Description Page
5ACINTPUT
4
A.M. Antenna
6 SubWoofer Socket
3 Aux Input
A.C. Voltage Selector
Ver
1
2
Class No
GENERAL PART 1 - BACK PANNEL SPECICFICATION
Issued Date
FWT6600/ All Version
23-Sep-11
Weight ( exclusive packing & batery )26Kg Units in Dealercarton
Diemensions without Boxes ( wxhxd ) 1250mm X 340mm X 495mm Finshing : Chrome Plate
Weight ( inclusive packing )8.5Kg Units in Masstercarton
27
28
Diemensions with Boxes ( wxhxd )265mm X 382 mm X 345 mm Material :HIPS
CABINET
3
2
DATE :KT CHECK:
SH 190 - 2 A4NAME : 11
All manuals and user guides at all-guides.com

1-6
DATE :
NAME : ZC.ZENG
KT CHECK
11 SH 190 - 3 A4
3
3
POWER Consumption of FWT6600
CLIMATIC requirements
ALL climates : + 5 Dregree till + 35 Degree
/ 61, /93
No
60Hz, 50Hz
No
60Hz ±5%
No
MODERATE climates : + N.A till N.A Degree
REMARKS APPROBATION
Tested according to General Test Instruction refer to PHILIPS standary ( UAN -D1591 )
Measured according to PHILIPS standary ( UAN - L1059 ) unless other wise stated
All not mentioned date, please refer to PHILIPS standary ( XUW - 0010 - JUNE 2001 )
DERIVED
1
2
Remarks
Issued Date
<= 0.5W
Quality : 0.8 % ( Major ) 2.0 % ( Mirror )
Reliability : 3.0 % ( C 42 )
ECO Power mode :(without display,mafter 15
minute of auto ) <= 0.5W Ref. to CRS Ref. to CRS
/61 /93
GENERAL PART 1 - GENERAL SPECICFICATION
23-Sep-11
Class No
FWT6600 All Version
Ver
/ 37
120W/150W @ 0.2A
@ 1/8 Prated , NOM. A, INPUT 120W 120W 120W 120W
Maximum : 120W/150W @ 0.1A 120W/150W @ 0.1A 120W/150W @ 0.1A
< 1W
( DEMO mode " OFF " ) , NOM. A, INPUT 15w 15w
Standby mode with clock display(after 15 minute) < 1W Ref. to CRS Ref. to CRS
Frequency 60/50Hz 50Hz
/ 12/ 05 / 55/77/78/98
50Hz
XX
EN 60065
Page
III
EN 60065 CISPR 13
/55
9
EN 55013 / EN 55020
SAFETY requirements
811
GENERAL DESCRIPTION
MP3-USB Mini Hi FiSystem with Digital Tuner, 3CD/MP3
(2x235W+1x300W) For FWT6600 Power Amplifier,VFD Display,Aux in ,Remote control
Subwoofer Boxes of 8 Ohm x 1
XXI
Class Tuner Supply + Amplifier
N/A
XX
Clockipod CD-mp3Recorder
LIFETIME : 7 Years
No
USB
EN 60065
Yes
/ 12 /05
127 / 240 Vac
± 15 %
Voltage Selection
FCC99
/98
/05
Version
PERFORMANCE CLASSES
POWER SUPPLY
MAINS ( A.C. ) 120 Vac (110V-10%,
120V ±10%)
/ 55 /98 / 79
240 Vac
± 10 %
Version Safety EMC
/12 EN 60065 EN 55013 / EN 55020
CISPR 13
EN 60065 CISPR 13
/79
/ 37
230 Vac
± 10 %
220 Vac
f10 %
RADIATION / IMMUNITY requirments ( EMC ) for 12 version only
/37 UL 60065
II
10 3-6 5
All manuals and user guides at all-guides.com
all-guides.com

:
:
:
:
:
:
1-7
ELECTRICAL DATA (Main computer )
dB
CD 0 dB track ( Audio Disc 1, Trk 35 ) Subwoofer Out yes
DSC : Techno, Pop, Jazz, Optimal˄n/a Rock˅Channel Differencer at -40dB 3
Standby Mode Indicator : VFD display Clock active
Hum ( Volume control from min. till max. – 20 dB) < 200MAX YES
TECHNIAL DESCRIPTION
Total power 800W, matching LOUDSPEAKER of 2 x 3R+1 x 8R only 800W. INPUT SOURCE, CD/MPǃTUNERǃUSB ǃAUXǃPC(LINE) INPUTǃ
3DSC ( Digital Sound Control ). IS ( Incredible Sound )
GENERAL PART
INDICATORS
ECO Mode Indiicator : VTD turns off, ECO - Standby LED turn on
nW
Residual Noise ( Volume Minium ) < 60
OUTPUT stage Protection : Yes Temperature : Yes Shorcircuit : Yes
LoudSpeaker D.C. Protection : Yes.
Tuner FM 67.5KHZ AM80% Modulation -6dB Line Out ( Left / Right ) N.A
dB
INTERCONNECTS
Input Sensitity(±2 dB)rated ouput power at 1 kHz and 10kHz. Line Output Voltage ( *1 )
nW
VAC : N/A Channel Separation ( at 1 kHz ) ı5dB
IS : YES
WOOX : N/A Signal / Noise ( unweighted ) ı55
µWSubwoofer Out Hum( Volume minmun) <4
Digital Coaxial Out N.A
USB 0 dB track ( Audio Disc 1, Trk 35 ) Headphone N/A
SD 0 dB track
OUTPUT POWER ( * 1 ) At THD = 10% (Measured with 20Hz-20KHz filter), both channels driven ( Low channel at 1KHz, High channel at 10k Subwoofer channel at 63HZ)
Power output ( RMS ) NA
Rated Impedance
FL/FR channel : 3 Ohms at 30Hz to 10 KHz
Power output ( RMS )
NA
Subwoofer channel 300W per channel( Lim '-1dB )
( *1 ) Electrical parameters are to be measuremend at specker terminals across 3 Ohm load ( pure resistor )
10% Power output ( RMS )
loading 3 ohm of FL/FR channel˄1khz)
loading 8 ohm of SUB channel (63Hz)
AMP power test for One channel load
FL/FR channel 250W per channel ( Lim '-1dB )
A4
(*2)
GENERAL PART 1 - TECHNAICAL SPECICFICATION
Issued Date
3
KT
Ver
CHECK
11 4
DATE :
SH 190 - 4NAME : ZC.ZENG
IS off and OSM unless specified otherwise
Measuremend output power only for AUX model and CD model of used audio analyzer equipment.
One channel signal input ( L or R ), two channel load ( < Low ch. L + High ch. L > or < Low ch. R + High ch. R > )
LOUDSPEAKER ( BOXES ) Please to package document of Speaker Box Assy
Subwoofer : 8 Ohm at 40HZ to 125HZ
Remarks
with rated input signal in AUX mode; DSC setting in Jazz mode with DBB OFF
N.A
AUX/ PC
0 dB track
Nor: 2V Lim: 1.5V ~ 2.5V for /55 Booster Out
support
DCK3060
Dock
Nor: 600mV Lim: 350mV ~ 900mV for /37
2
23-Sep-11
Class No
FWT6600/ All Version 1
All manuals and user guides at all-guides.com

TECHNIAL DESCRIPTION
Bluetooth Function
GENERAL PART
1-8
Bluetooth Version : Ver2.1 + EDR
YES
Bluetooth SPECICFICATION
Class No
FWT6600 All Version
Ver
REMARKS
Receive HSP N/A Noise Reduction System : No
Receive A2DP: N/A
Transmit A2DP: N/A Remote Controlled :
Unit
Display : N/A
INDICATORS
Bluetooth Flashing : Yes
Frequency Response 125-16khz f dB
ELECTRICAL DATA
Bluetooth at Module level: Mobile Phone lim
dB
S/N (A-weighted) ı  dBA
S/N (Unweighted) ı 
dB
Channel Separation ı  dB
Level Diff ? f
λ
Bluetooth at Set Level Mobile Phone
Distortion ˘
10%THD OUTPUT POWER(EQ:FLAT) \ 125± 3dB W
meter
Issued Date
110-Jul-10
Connected distance 8~10
2
3
CHECK: DATE :
NAME : TAN DATE : SH 190 - 9
All manuals and user guides at all-guides.com

1-9
6.1+4-
Tabel 1b ( Tolerance ± 3dB )
5.4-06-5.2-
12 kHz 0-2 -6
+17
60 Hz
+15
DSC Modes with DBB Off ,MAX OFF
Pop
+12
1+1+5.0-5.0+0zHk1
12 kHz
1.5
SAMBA/OptimalTECHNO/Jungle
Tabel 1b ( Tolerance ± 3dB )
0
Frequency
0
Refence level for DSC'S with DBB on=500mW at the speaker terminal .
Inject sine wave 500mV-2.4V to AUX-IN socket with frequencies indicated in Table 1.
For Subwoofer 60HZ @ 8R
Tabel 1a ( Tolerance ± 3dB )
Frequency lamitpO/ABMASKCORZZAJ
+12+7
+22
JAZZ ROCK
DSC Modes with DBB 2 ON ,MAX OFF
Pop
2 ) DBB ( Dynamic Bass Boot )
15.0-5.0+zHk1
+17
60 Hz
+12
+14
Tabel 1a ( Tolerance ± 3dB )
AUDIO SIGNAL PROCESSING
MP3-USB Mini Hi Fi System with Digital Tuner ,3 CDC-MP3, (2×235W+300W)only FWM663 Universal Class D Power Amplifier
1 ) DSC ( Digital Sound Control )
Select AUX as input source with the following set conditions:
Inject sine wave 500mV-2.5V at 1 KHz to L/R channels of AUX-IN socket(input level 600mV for /37/05/12,2V-2.5V for /55/77/78 ).
Set DSC to JAZZ(Flat) mode and switch off DBB.
Refence level for DSC's without DBB OFF=500mW.
Frequency DSC Modes with DBB 1 ON ,MAX OFF
Pop
+17
JAZZ ROCK TECHNO/Jungle SAMBA/Optimal
TECHNO/Jungle
22+12+22+61+
60 Hz
+10
12 kHz
0
5.1+4+1+zHk21
-3
SAMBA/Optimal
42
-3
6.0+5.0+5.0-
+25+22 +25 +25
JAZZ ROCK TECHNO/Jungle
+0.6
+1.6
Tabel 1b ( Tolerance ± 3dB )
+1
-1
-4
25.11
-5 -4.5
-3 8
Frequency Subwoofer
DBB 3DBB 1 DBB 2
hcRF/LFhcRF/LF
VAC Mode FL/FR ch
DBB OFF
2
3
5.3202-
102-
12 7 17
Subwoofer
S
ubwoofe
r
refoowbuShcRF/LF
16 24
24 17 2791914
5231517013
Cinema
Hall
20
-6
1-5-7-9-
1 KHz
Concert
6-6-7-
19
60 Hz
Concert
Hall 14
12K Hz
4
Cinema
Hall
Cinema -5.5
2
Concert
5.0+5.0-
1kHz
Tabel 2 ( Tolerance ± 3dB ) NO TEST
1kHz
Select AUX as input source with the following set conditions :
Inject sine wave 500mV-2.5V at 1kHz to L/R channels of AUX - IN socket(input level 600mV for /37/05/12,2V-2.5V for /55/77/78 ).
60 Hz
-1
Set VAC to JAZZ(Flat) mode and switch off DBB of Reference level,
Frequency DSC Modes with DBB 3 ON ,MAX OFF
Pop
0+1
1
Issued Date
KT
Ver
2
For Subwoofer 60HZ @ 8R ;FR/FL 1Khz @3R
+25
Reference level for the test is 500mW on the speaker terminals.
CHECK
Class No
FWT6600/ All Version
DATE :
NAME : ZC.ZENG
11 6
GENERAL PART 1 - GENERAL SPECICFICATION
A4
3
SH 190 - 6
23-Sep-11
All manuals and user guides at all-guides.com

1-10
DBB 2
DBB 1
Hall DBB 1
Cinema
DBB Level preset DBB Level presetVAC MODE
Concert DBB OFF
3 ) IS ( Incredible Sound )
Select AUX as input source.
Inject sine wave 600mV-2.5V at 1kHz to AUX-IN socket, one channel at a time (input level 600mV for /37/05/12;2V-2.5V for /55/77/78 )
DBB OFF
DBB 1
Set DSC to JAZZ ( Flat ) mode and switch of DBB, OSM & INCREDIBLE SURROUND.
Adjust volume level to obtain 500mW across 3 OHM load at L/R speaker output.
-7.0 dB
-1 dB
- - 1.0 dB -2V60 Hz
Table 3 ( Tolerence ± 4 dB )
AUDIO SIGNAL PROCESSING
MP3-USB Mini Hi Fi System with Digital Tuner , 3 CDC-MP3,(2×235W+300W)only FWT6600, Universal Class D Power Amplifier
FREQ INPUT LEVEL OUTPUT LEVEL
+2.0 dB -15.0 dB
Inject sine wave 2V to AUX-IN socket withfrequency indicated in Table 3 .
LEFT RIGHT LEFT RIGHT
IS OFF IS ON
12 kHz
01 kHz
- 0.5 dB + 3.0 dB
+ 3.5 dB
-
2V -
2V
-
PoP
DBB 3
as show in Table 4.
Note : The above specs also apply to right channel.
4 ) DSC Mode ( Jazz , POPˈRock, Techno and Optimal )
The VAC modes are software controlled by switching the combination between DBB and DSC modes
0
LEFT RIGHT
DSC MODE
Samba/Optimal
Rock
Jazz
Techno
Class No
-
DBB 1

Max ON
Max OFF
+8
1 kHz
GENERAL PART 1 - AUDIO SIGNAL SPECICFICATION ( 2 )
NAME : ZC.ZENG 11 7 SH 190 - 7 A4
Max OFF Max ON
60 Hz -1 +18
12 kHz -1 
KT CHECK DATE :
FR/FL˄at stereo mode) SUB˄at stereo mode)
The 1W level will be used as 0 dB reference
Inject sine wave 2V-2.5V to AUX-IN socket withfrequency indicated in Table 5 .
FREQ
2
FWM/6500/ All Version
Ver Issued Date
3
+27
123-Sep-11
Set DSC to JAZZ ( Flat ) mode and switch of DBB, OSM & INCREDIBLE SURROUND.
Adjust volume level to obtain 500mW across 3 OHM load at L/R speaker output.
Note : When these modes are activ DBB and DSC will not be displayed
5 ) MAX ( Maximum Sound ) ( Tolerence ± 3 dB )
Select AUX as input source.
Inject sine wave 600mV-2.5V at 1kHz to AUX-IN socket, one channel at a time (input level 600mV for /37/05/12;2V-2.5V for /55/77/78 )
All manuals and user guides at all-guides.com

1-11
KT
9)''LVSOD\7\SH 9)'
123-Sep-11
2
NAME : ZC.ZENG 11 8
CHECK DATE :
FWT6600/ All Version
Remark
CLOCK / TIMMER SPECICFICATION
Class No Ver Issued Date
3
SH 190 - 8 A4
/&''LVSOD\7\SH QD
Remarks Time Setting : 12hr for /37 version, 24hrs for other version.
Volume at Wakeup : Last Setting
1RRI7LPHU6HWWLQJV : 1
&ORFN$FFXUDF\ : Nom : 1 sec/day Limit : 2 sec/day
TECHNIAL DESCRIPTION
SOFTWARE IMPLEMENTED CLOCK / TIMER FUNCTION WITH 12MHZ QUARTZ OSCILLATOR.
GENERAL PART
,1',&$7256
Timer Setting : Clock and Timer
Timer Wakeup Mode : CD or Tuner or USB
All manuals and user guides at all-guides.com
all-guides.com

CHECK
11 9 SH 190 -9
1-12
Ver
1
DATE :
NAME : ZC.ZENG
Remarks :
testing with 20 to 20k Hz filter
USB SPECICFICATION
Issued DateClass No
A4
23-Sep-11
FWT6600/ All Version
3
2
Channel Unbalance ( 0 dB, 1 KHz ) +/- 2dB
Channel Crosstalk ( 0 dB, 1 KHz ) >= 35dB (with 1 KHz filter )
USB Measurement at Set Level
Electrical Parameters are to be measured at speaker teminals across 6 ohm load with 500mW output and DSC setting in Jazz Mode
Signal to Noise Ratio ( 0 dB, 1 KHz ) >= 55dBA ( A - weighted )
FL/FR ch
Frequency response @±3 30HZ-10KHZ(Reference 1KHZ)
Description Specification
Channel Crosstalk ( ( 0 dB, 1 KHz ) ) >= 35dB
( 0 dB, 1 KHz ) >= 35dB
Signal to Noise Ratio ( 0dB,1kHz ) ( A - weighted ) >= 57dB( A - weighted )
30HZ-125HZ(reference 63HZ)Sub ch
THD + Noise ( 0dB, 1Khz ) <=2%
Output Resistance N/A
Output Voltage RL = 33 k ohm ( )dB, 1 Khz ) N/A
Channel Unbalance < = +/- 3 dB
TECHNIAL DESCRIPTION
USB
See also SH 190 USB/SD Audio Module (300605)
Measurment are directly done at the coonector on the board
Measurement are directly done at the connector on CDC board
Description Specification
GENERAL PART
All manuals and user guides at all-guides.com

1-13
19-35
dB
S/N Ratio (at 1000khz)
45 40 50 45
: 10.7 ± 0.03
Crosstalk (RF1mV, Freq Dev.40kHz )
dBf
Search Tuning Sensitivity
: ɲ26 +/-10 dB 24-30
± 3 kHz
49
dB
MHz
IF
TECHNIAL DESCRIPTION
TUNER used SI4730 soultion
GENERAL PART
: 25 18
Distortion ( RF 50mV, M 80% )
: 3
IF
: 450
WAVE RANGE TOLERANCE TUNING GRID
FM( 55/37 ) 87.5 - 108.00 MHz QUARTZ PRECISION 100 kHz
FM( 12 ) 87.5 - 108.00 MHz 50KHZ
AM (55/37) 530 - 1700 kHz QUARTZ PRECISION 10 kHz
VFD
%
AGC Figure of Merit
: 30 25 dB
-4 dB
Amplification Reverse
dBf%
Amplification Reverse
: - 2 -4 dB
3
: 0
Distortion ( RF 1mV, Frq Dev.75 kHz )
: 2
Nom Limit
Stereo - 46 dB Quieting
: 46
Unit F.M. Nom
5
- 3 dB Limiting Point
: 17
INDICATORS
Limit Unit
23.5 dBf
A.M
QUARTZ PRECISION 9 kHz
AM : FRAME ANT. 18.1 uH with shielding
AERIAL
FM : PIGTAIL ANT WIRE 300 Ohm(for/37) 75ohm for 55/12
AM (12) 531 - 1602 kHz
dB
FM 98 MHz
29-Jul-10
23-Sep-11
Issued Date
Remarks˖MAX.Sens -6dB
TUNER SPECICFICATION
1
FWT6600/ All Version
VerClass No
2
25db
65db 116 dBudBf 40db
Lim.
22 dBf
dBf
FM 108 MHz Nom.
18
30db 60db 108 dBu
45db
65db 30db
Lim.
22 dBf 30db 60db 108 dBu 25db
28db
116 dBu
MW 1440 kHz Nom.
1500 uV/m
Nom.
40db
24db
3500
22db
Lim.
uV/m 28db 500mv/m
1000mv/m
18db
32db
24db
Selectivit
y
22db
Lim.
Wave Range Large Signal
18db
MW 630 kHz
Nom.
32 db
Uv/m
28db
500mv/m
uV/m 1000mv/m
Noise Limited Sensitivity Į26 dB
Image Rejection
IF Rejection
4000 28db
18
4000
NAME : ZC.ZENG A411 10 SH 190 - 10
KT CHECK DATE :
3
All manuals and user guides at all-guides.com

Issued Date
1-14
TNO 11 of Sub chassis 8A
A4
2
Class No
3
Playback position Solid, Normal position (Set is located on a flat surface, floor)
TNO 13 of SBC 444A (7104 099 24990)
TNO 1,6 of 0.6mm skew (7104 099 28260)
Hwavy fingerprint No track jumper/plops
1. Playback of above mentioned tracks possible wihout track loss or audible defects.
2. Double black dot, max. diameter, thin/disk is according to PQR or AR 30-05-239
Frequency Response 63Hz
FL/FR ch
Sub ch dB
1
Black dot 500um 800um
Ver
1
CHECK
11 11 SH 190 -11
DATE :
NAME : ZC.ZENG
KT
3. This unit can playback (only) CD-R or CD-RW discs. For performance specification, Please refer to module.
specification of CD99 (3103 308 52190)
23-Sep-11
CD / MP3 SPECICFICATION
FWT6600/ All Version
TNO 10 of Sub chassis 8A
Bad HF track No audible defect TNO 8 of Sub chassis 8A
Skew 0.6mm No audible defect
Eccentric 150um
Fingerprint No audible defect
Limit Typical Test disc
200um TNO 1, 24 of 200um disc (7104 099 24960)
Wedge 600um 900um TNO 7, 9 of SBC 444A(7104 099 24990)
REMARKS:
1. Amplification reserve for CD = +2dB ('±2dB),Ref.Level for CD is a 0dB track instead of a .-6dB track.
Playability :(acc.To AR 30-05-239 )
%THD (10KHz -20dB) <1 <3
mV
THD (1KHz -6dB) 0.2 <1 %
Hum & Noise ( *1 ) 1 1.5
55
dBA50
dB
dB
dB
Sub ch
Crosstalk ( 1kHz ) ( A - weighted ) >= 35dB
dBA
Signal to Noise Ration ( Unweighted ) 60
Signal to Noise Ration ( A - weighted )
na TEST
high ch
Frequency Response ( 40Hz - 125Hz ) reference 63Hz
Frequency Response ( 63Hz -10kHz )reference 1kHz
65
De-emphasis 15us / 50us Switchable via Subcode information
Frequency accuracy
'± 3
± 3
Low ch ± 3
± 3
-5
N/A ± 0.5
12
Frequency Response ( 30Hz - 10 kHz )reference 1kHz
8
Channel Unbalance
reference 1kHz
Servo processor
%
dB
Lim
AUDIO part: Measurement with Audio Signals Disc-783 7104 078 04911 on spkeakers or Headphone socket with nom.load
TECHNIAL DESCRIPTION
CD + MP3 - Part Specifications (CD MECHAISM DA11VZSS OF SANYO )
Inpu
t
AMP IC Outpu
t
Motor Logic control
Active components TDA7468D WM8782SEDS/R NJM4556AM
UnitDescription Extern Filter Nom
--
BU9543KV+BA5826FP
Signal processsing D/A converte
r
HF-preamplifie
r
MLC3895
--
Act
i
ve components 7'
$


7+ 3CD-TDA7073A
All manuals and user guides at all-guides.com

1-15
GENERAL PART
TECHNIAL DESCRIPTION
Microphone
See also SH 190 testing with 20 to 20k Hz filter,input leven 1mv rms(lim:1.5mv rms) Rs=600ohm output 500mW
Measurment are directly done at the coonector on the board
THD + Noise ( 0dB, 1Khz )vol max
Output Resistance
Output Voltage RL = 33 k ohm ( )dB, 1 Khz )
Measurement are directly done at the connector Microphone(mic1,mic2)
Description Specification
Lim

Microphone Frequency response at
volume 23,input leven 1mv rms,
connect main load
.+=

+=
Remarks :
testing with 20 to 20k Hz filter
USB SPECICFICATION
68%FK
)/)5FK .+=
+=
Issued Date
23-Sep-11
Class No
FWT6600/ All Version 1
3
2
SH 190 -9
Ver
A4
CHECK DATE :
NAME : ZC.ZENG 11 9
dBA
Channel Unbalanceo about( mic1 and mic2)
Unit
dBA
Nom
N/A
86
Signal to Noise Ratio ( 0dB,1kHz ) ( A - weighted )
Channel Crosstalk ( ( 0 dB, 63Hz ) )
( 0 dB, 1 KHz )
35
+/- 31
dB
dB
dB
±4
ref
±3

N/A
mV
dB±3
%
mV
N/A
N/A
Max Hum Noise(mic vol max,main vol max) 6 8
550 +/- 20%Microphone Power output( RMS )
Microphone input leven ( Rms)
40
mW
1 1.5 mV
Vol.min=vol1.(mic vol min,main vol 1) 2 4
All manuals and user guides at all-guides.com

1-16
DATE :
NAME : ZC.ZENG 10 10 SH 190 - 12
KT CHECK
A4
3
FWT6600 All Version
Ver
2
123-Sep-11
Issued DateClass No
VERSION OVERVIEW
220V
60Hz IEC IEC
EN60065
CLASS II
FM 87.5-108MHz MW
531-1602kHz
50kHz
9kHz
75 Ohm Coaxial
JST XH 2P Side
75 Ohm Pigtail
Loop Sagami 18.1uH
No
No
No No
IEC IEC/35 China EN60065
CLASS II No
75 Ohm Pigtail
Loop Sagami 18.1uH
220V
60Hz
/ 33 Korea
IEC
FM 87.5-108MHz MW
531-1602kHz
50kHz
9kHz
75 Ohm Coaxial
JST XH 2P Side
No
FM 87.5-108MHz MW
530-1710kHz
100kHz
10kHz
JALCO Click Fit
JST XH 2P Side
300 Ohm Dipole
Loop Sagami 18.1uH
120V
60Hz
No
No No
NoNo
No
IEC IEC
75 Ohm Pigtail
Loop Sagami 18.1uH
240V
50Hz
/37 USA
Canada UL 6500 FCC 99 ULUL
75 Ohm Coaxial
JST XH 2P Side
110-127V
Switched
220 - 240V
50/60Hz
75 Ohm Pigtail
Loop Sagami 18.1uH
FM 87.5-108MHz MW
531-1602kHz
or 530-1710kHz
50kHz
9kHz
10kHz
75 Ohm Coaxial
JST XH 2P Side
75 Ohm Coaxial
JST XH 2P Side
75 Ohm Pigtail
Loop Sagami 18.1uH
/55 /98 OVS
EN60065
CLASS II
SISR
TAIWAN
CISPR 13
FM 87.5-108MHz MW
531-1602kHz
50kHz
9kHz
/79 AUST / NZ EN60065
CLASS II
IEC IEC
/05 / 12 EUROPE
EN60065
SEMKO
DEMKO
NEMKO SEV
BS415-UK
EN55013
EN55020
FM 87.5-108MHz MW
531-1602kHz
50kHz
9kHz
230V
50Hz IEC
VERSION OVERVIEW FWT6600
Ver DEST
APPROBATION TUNER AC SUPPLY
MAINS
VOLTAGE SOC. CORD
MIC
MIX
MAT
RIX
SURR
. SPK.
SAFETY EMC Wave RANGE GRID AERIAL SOCKET AERIAL SUPPLIED
All manuals and user guides at all-guides.com
all-guides.com

2.0 SAFTETY INSTRUCTIONS
GB
WARNING
All ICs and many other semi-conductors are
susceptible to electrostatic discharges (ESD).
Careless handling during repair can reduce life
drastically.
When repairing, make sure that you are
connected with the same potential as the mass
of the set via a wrist wrap with resistance.
Keep components and tools also at this
potential.
F
ATTENTION
Tous les IC et beaucoup d’autres
semi-conducteurs sont sensibles aux
décharges statiques (ESD).
Leur longévité pourrait être considérablement
écourtée par le fait qu’aucune précaution n’est
prise à leur manipulation.
Lors de réparations, s’assurer de bien être relié
au même potentiel que la masse de l’appareil et
enfiler le bracelet serti d’une résistance de
sécurité.
Veiller à ce que les composants ainsi que les
outils que l’on utilise soient également à ce
potentiel.
ESD
D
WARNUNG
Alle ICs und viele andere Halbleiter sind
empfindlich gegenüber elektrostatischen
Entladungen (ESD).
Unsorgfältige Behandlung im Reparaturfall kan
die Lebensdauer drastisch reduzieren.
Veranlassen Sie, dass Sie im Reparaturfall über
ein Pulsarmband mit Widerstand verbunden
sind mit dem gleichen Potential wie die Masse
des Gerätes.
Bauteile und Hilfsmittel auch auf dieses gleiche
Potential halten.
NL
WAARSCHUWING
Alle IC’s en vele andere halfgeleiders zijn
gevoelig voor electrostatische ontladingen
(ESD).
Onzorgvuldig behandelen tijdens reparatie kan
de levensduur drastisch doen verminderen.
Zorg ervoor dat u tijdens reparatie via een
polsband met weerstand verbonden bent met
hetzelfde potentiaal als de massa van het
apparaat.
Houd componenten en hulpmiddelen ook op
ditzelfde potentiaal.
I
AVVERTIMENTO
Tutti IC e parecchi semi-conduttori sono
sensibili alle scariche statiche (ESD).
La loro longevità potrebbe essere fortemente
ridatta in caso di non osservazione della più
grande cauzione alla loro manipolazione.
Durante le riparazioni occorre quindi essere
collegato allo stesso potenziale che quello della
massa dell’apparecchio tramite un braccialetto
a resistenza.
Assicurarsi che i componenti e anche gli utensili
con quali si lavora siano anche a questo
potenziale.
“Pour votre sécurité, ces documents
doivent être utilisés par des spécia-
listes agréés, seuls habilités à réparer
votre appareil en panne”.
GB
Safety regulations require that the set be restored to its original
condition and that parts which are identical with those specified,
be used.
NL
Veiligheidsbepalingen vereisen, dat het apparaat bij reparatie in
zijn oorspronkelijke toestand wordt teruggebracht en dat onderdelen,
identiek aan de gespecificeerde, worden toegepast.
F
Les normes de sécurité exigent que l’appareil soit remis à l’état
d’origine et que soient utiliséés les piéces de rechange identiques
à celles spécifiées.
D
Bei jeder Reparatur sind die geltenden Sicherheitsvorschriften zu
beachten. Der Original zustand des Geräts darf nicht verändert werden;
für Reparaturen sind Original-Ersatzteile zu verwenden.
I
Le norme di sicurezza esigono che l’apparecchio venga rimesso
nelle condizioni originali e che siano utilizzati i pezzi di ricambio
identici a quelli specificati.
"After servicing and before returning set to customer perform a
leakage current measurement test from all exposed metal parts to
earth ground to assure no shock hazard exist. The leakage current
must not exceed 0.5mA."
CLASS 1
LASER PRODUCT
3122 110 03420
GB
Warning !
Invisible laser radiation when open.
Avoid direct exposure to beam.
SVarning !
Osynlig laserstrålning när apparaten är öppnad och spärren
är urkopplad. Betrakta ej strålen.
SF Varoitus !
Avatussa laitteessa ja suojalukituksen ohitettaessa olet alttiina
näkymättömälle laserisäteilylle. Älä katso säteeseen!
DK Advarse !
Usynlig laserstråling ved åbning når sikkerhedsafbrydere er
ude af funktion. Undgå udsaettelse for stråling.
Caution: These servicing instructions are for use by qualified service personnel only.
To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.
2-1
All manuals and user guides at all-guides.com

Whenthepowersupplyisbeingturnedon,youmaynotremovethislasercautionslabel.Ifitremoves,radiationoflaser
maybereceived.
2.1 ESD PROTECTION
PREPARATIONOFSERVICING
PickupHeadconsistsofalaserdiodethatisverysusceptibletoexternalstaticelectrocity.
Althoughitoperatesproperlyafterreplacement,ifitwassubjecttoelectrostaticdischargeduringreplacement,
itslifemightbeshortened.Whenreplacing,useaconductivemat,solderingironwithgroundwire,etc.to
protectthelaserdiodeformdamagebystaticelectricity.
Andalso,theLSIandICaresameasabove.
Solderingiron
withgroundwire
orceramictype
Groundconductive
wriststrapforbody.
Conductivemat
Thegroundresistance
betweenthegroundline
andthegroundislessthan10
1M
2-2
All manuals and user guides at all-guides.com

SAFTY NOTICE
Plug the AC line cord directly into a 120V AC outlet (do
not use an isolation transformer for this check). Use an
AC voltmeter, having 5000 per volt or more sensitivity.
Connect a 1500 10W resistor,paralleled by a 0.15uF
150V AC capacitor between a knomn good earth ground
(water pipe, conduit, etc.) and all exposed metal parts of
cabinet (antennas, handle bracket, metal cabinet
screwheads, metal overlays, control shafts, etc.).
SAFTY PRECAUTIONS
LEAKAGE CURRENT CHECK
Measure the AC voltage across the 1500 resistor.
The test must be conducted with the AC switch on and
then repeated with the AC switch off. The AC voltage
indicated by the meter may not exceed 0.3V.A reading
exceeding 0.3V indicates that a dangerous potential
exists, the fault must be located and corrected.
Repeat the above test with the DVD VIDEO PLAYER
power plug reversed.
NEVER RETURN A DVD VIDEO PLAYER TO THE
CUSTOMER WITHOUT TAKING NECESSARY
CORRECTIVE ACTION.
READING SHOULD NOT EXCEED 0.3V
DVD VIDEO PLAYER
AC OUTLET
AC VOLTMETER
Test all exposed metal.
Voltmeter Hook-up for Leakage Current Check
0.15uF 150V AC
1500
10W
(5000 per volt
or more sensitivity)
Good earth ground
such as a water pipe,
conduit, etc.
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated "dangerous voltage" within the
product's enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
2-3
All manuals and user guides at all-guides.com

2.2 SAFETY INSTRUCTIONS
Battery Handling Guideline
Since the battery is packed in soft package, to ensure its good performance, it’s very important to carefully handle
the battery
2.2.1 Soft Aluminium foil
The soft aluminum packing foil is very easily damaged by sharp edge parts such as Ni-tabs, pins and needles.
• Don’t strike battery with any sharp edge parts
• Trim your nail or wear glove before taking battery
• Clean worktable to make sure no any sharp particle
2.2.2 Sealed edge
Sealing edge is very flimsy
• Don’t bend or fold sealing edge
2.2.3 Folding edge
The folding edge is formed in battery process and has passed all hermetic tests.
• Don’t open or deform folding edge
2.2.4 Tabs
The battery tabs are not so rigid especially for aluminum tab.
• Don’t bend tab
2.2.5 Mechanical shock
• Don’t fall, hit, bend battery body
2.2.6 Short
Short terminals of battery is strictly prohibited, it may damage battery.
Caution: Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
2-4
如果电池更换不当会有爆炸危险,只能用同样类型或等效类型的电池来更换.
电池不得暴露在诸如日照、火烤或类似过热环境
The battery shall not be exposed to such as sunshine, fire or similar overheated environment.
All manuals and user guides at all-guides.com