Placid Point Lighting PYRAMID POST CAP LIGHT User manual

Lighting Components
• Post Light Cap
(Lens Options Available)
• Post & Stair Light
(Color Options Available)
• Control Box/ Power Supply
(Color Options Available)
Outdoor L.E.D.
Lighting System
Recommended Tools
• Safety Glasses
• Tape Measure & Pencil
• Power Drill w/ 3/8'', 3/4'' bit
• Level
PPLIG180227
• These directions are only a guide and may not address every situation.
• Always wear proper safety equipment while assembling and installing.
• The installer should obtain all required building permits and follow all installation procedures in accordance
with applicable building code requirements.
• Superior Plastic Products, Inc. shall not be held liable for improper or unsafe installations.
• Applying paint, will void your warranty.
• To ensure proper coverage by our warranty please visit our website and complete the warranty form and mail
to: Superior Plastic Products, Inc., 260 Jalyn Drive, New Holland, PA 17557
260 Jalyn Drive ● New Holland, PA 17557
PlacidPointLighting.com

PlacidPointLighting.com
- Mini Mizu P-25
Waterproof Connector
- Conformal Coating
- High output 3000K
L.E.D. bulbs
- Rated at over
50,000 hours
Lighting
Control Box
3/8'' access
hole
Post Light
Cap
3/8'' access
hole
Two-Way
Splitter
Power Line
(Input)
Power Line
(Output)
Each component of the Placid Point Lighting system was designed with a "Plug & Play" mind-set so
that it is easy for the end user to install with little to no construction experience.
Post Light Caps come pre-assembled, ready to t directly onto your existing Post (various sizes
available). They are designed to be a snug t; as such they
can be installed without the need for any
extra fasteners. However, in the event that you
wish to ensure they cannot be removed easily;
it is acceptable to fasten it by placing a screw
through the lower trim into the Post (fasteners
provided).
Several styles of Post Light Caps are available
to suit each customers needs. Each LED light
board is coated in an Optical Conformal Coating
to protect the circuitry from normal
environmental conditions.

PlacidPointLighting.com
It is a good practice to place your Post Light Caps, and Post
and Stair Lights rst so that you know how much more room
is needed for extensions.
The Power Supply can be mounted under the deck, and out
of sight. With an IP67 Waterproof rating there's no need to
worry if it gets wet. It is our recommendation that a "drip
loop" be created during wire routing. Below is an image of
how to properly orient the wires.
18''
Power Line (input)
Staple close
to Connector 3/8''
Access hole
Place a staple (provided) approximately every 18''; with the
rst and last staple as close to the Connectors as possible.
Place Lens sub-assembly over access hole
utilizing the adhesive to hold it in place
Fasten Lens sub-assembly using
#8 x 1'' Pan head Screws (provided)
take care not to overtighten
Snap Powder Coated Aluminum Cap
onto Lens sub-assembly
Drill a 3/8'' access hole for the Post &
Stair Adapter cable
Post & Stair Light
Installation
Power Supply

PlacidPointLighting.com
It's good to know the location of each light you want to install on your deck. Con-
sider making a sketch to help better determine where everything will go, and
exactly how many of each part is needed.
- Measure each section, and mark the lengths in between each Post accordingly
- Measure the height of your Posts
- Count the number of Splitters you will need, and which type is required
- Make a note of where holes will need to be drilled, both on Posts or Deck
Post & Stair
Light
2', 5' or 9'
Extensions
Power Supply
2-way Splitter
3-way Splitter
Lens Light Cap
or
Down Light Cap
Item Qty.
Down Light Cap
Lens Light Cap
Post & Stair Light
2' Wire Extension
5' Wire Extension
9' Wire Extension
2-Way Splitter
Post Light Wire Kit
4-Way Splitter
{
{