Planet Networking & Communication IHD-410PT User manual

– 5 – – 6 –
4. Connect the USB cables from Transmitter to PC, and connect the USB
additional devices such as USB mouse, USB keyboard and USB pen
drive to Receiver.
5. Use Cat5e/6 cables (EIA/TIA 568B industry standard compliant) for
connection between Transmitter/Receiver and the IEEE 802.3af/at
PoE+ switch.
6. Apply the proper power to all connecting devices.
7. Connect the IR emitter cable with Transmitter and the IR receiver
cable with Receiver for remote control.
Note
It is suggested using the Gigabit IEEE 802.3af/at PoE+
Ethernet switch with IGMP Snooping and Jumbo Frame
to ensure optimal transmission quality.
If users encounter no screen display in computer
connection:
1. Make sure the device cables are correctly and rmly
attached.
2. Set your display device’s (TV, monitor, etc.) input
source as HDMI.
3. Check the PC BIOS conguration about the video
output setting.
4. Connect your computer to the HDMI Display
DIRECTLY to check if the video signal gets through.
Connection Pattern
1. Point to Point:
Video Extender
* More PoE switches and RXs (Receivers) can be used to distribute a single video signal to multi-monitors.
STEP 3STEP 1 STEP 2
Input Source Output Source Link
Video Source
1000BASE-T UTP
IHD-410PR
IHD-410PT IHD-410PR
IHD-410PT
HDMI HDMI
2. Multicasting:
USB
Video
USB
Video
USB
Video
USB
Video
USB
Video
Gigabit PoE Switch
(with IGMP Snooping and Jumbo Frame)
IHD-410PT (Transmitter 1)
IHD-410PR
(Receiver 1) IHD-410PR
(Receiver 2)
IHD-410PR
(Receiver 3)
IHD-410PR
(Receiver 4) IHD-410PR
(Receiver 5)
USB
Video
IHD-410PT (Transmitter 2)
USB
Video
IHD-410PT (Transmitter 3)
USB
Video
IHD-410PT (Transmitter 4)
USB
Video
IHD-410PT (Transmitter 5)
USB
Video
PoE
1000BASE-T UTP with PoE
USB Line
USB
Video Line
Video
PoE
PoE
PoE
PoE
PoE
PoE
PoE
PoE
PoE
PoE
PC/Server
PC/Server
PC/Server
PC/Server
PC/Server
Multiple HDMIs and USB over IP Interaction Application
Further Conguration
For detailed conguration, please refer to user manual downloadable
from the web site. (http://www.planet.com.tw/en/support/download.php).
User’s Manual
If you have any other question, please contact the dealer where
you purchased this product or you can contact PLANET directly at the
following email address: [e-mail]

– 1 –
– 3 –
– 2 –
– 4 –
6 7 8 10911 12 13
Transmitter (IHD-410PT)
1 2 3 4 5
6 7 8 10 11 12 14
Receiver (IHD-410PR)
Position Description Function
1Ethernet
(PoE)
Connect to a LAN Switch.
IGMP snooping and Jumbo Frame
supported Gigabit IEEE 802.3af/at PoE+
Ethernet switch is recommended.
LED:
1. LAN LED (green color):
This LED will be ashing while network is
accessing via Ethernet.
2. Power LED (orange color):
When the device is powered on, and the
device is connected to Ethernet switch, the
LED will be always on.
Verify The Contents Inside Package Box
The package should contain the following items plus IHD-410 series. If
any item is missing or damaged, please contact the seller immediately.
Quick Installation Guide IR Emitter Cable
(Comes with Transmitter)
IR Receiver Cable
(Comes with Receiver)
Mounting Bracket Screws
Product Outlook & Functions
1 2 3 4 5
Position Description Function
2HDMI
Transmitter: HDMI Type-A female connector
for connecting to the HDMI source.
Receiver: HDMI Type-A female connector for
video output.
3Audio In 3.5mm jack for connecting an external active
microphone.
4Audio Out 3.5mm jack for connecting an active loud
speaker.
5DC 12V
12V/2A DC power input.
Only use one power source, either from DC or
from 802.3af/at PoE+ Ethernet switch.
6ACT/Link
ACT: ACT LED indicator turns blue when
the device is powered up.
 Link: Link LED indicator ickers green
when network connection is waiting for
video source, turns green when network
connection and video source is functioning
properly.
7RS-232 DB-9 female connector for RS-232
bi-directional remote extension.
8IR
Transmitter: 3.5mm jack for IR emitter cable
to control video source device.
Receiver: 3.5mm jack for IR receiver cable to
receive signal from remote controller.
9PC USB USB Host Input Port.
10 Group Group conguration, 4-bit switch for 16
stream channel selection.
11 Reset
This button supports two functions: “Restore
to factory default setting” and “Stop
connecting to video source”.
Position Description Function
11 Reset
Restore to factory default setting:
1. Turn on the device rst.
2. Press and hold the button for over 15
seconds. Once the device is operational
again, it has restored to default settings.
Stop connecting to video source:
1. Turn on the device rst.
2. Press and hold the button for 1 second,
the link LED will turn off, the device does
not connect to video source.
3. Press and hold the button for 1 second
again, the link LED will turn on, the device
will connect to video source again.
12 G/V Mode
Press the button for 1 second to select
Graphic Mode or Video Mode (also deploy
to all the IHD-410PT and IHD-410PR of the
same channel).
13 VGA Out DB9 connector for VGA local display.
14 USB
USB ports for additional USB devices such
as USB mouse, USB keyboard and USB pen
drive.
Installation
1. Connect the video source to the Transmitter/Sender (IHD-410PT)
Unit’s HDMI In interface.
2. Connect the monitor to the Receiver (IHD-410PR) Unit’s HDMI Out
interface.
3. Set an identical ID number on DIP switch for all units of the same
group.

– 1 –
– 3 –
– 2 –
– 4 –
6 7 8 10911 12 13
Transmitter (IHD-410PT)
1 2 3 4 5
6 7 8 10 11 12 14
Receiver (IHD-410PR)
Position Description Function
1Ethernet
(PoE)
Connect to a LAN Switch.
IGMP snooping and Jumbo Frame
supported Gigabit IEEE 802.3af/at PoE+
Ethernet switch is recommended.
LED:
1. LAN LED (green color):
This LED will be ashing while network is
accessing via Ethernet.
2. Power LED (orange color):
When the device is powered on, and the
device is connected to Ethernet switch, the
LED will be always on.
Verify The Contents Inside Package Box
The package should contain the following items plus IHD-410 series. If
any item is missing or damaged, please contact the seller immediately.
Quick Installation Guide IR Emitter Cable
(Comes with Transmitter)
IR Receiver Cable
(Comes with Receiver)
Mounting Bracket Screws
Product Outlook & Functions
1 2 3 4 5
Position Description Function
2HDMI
Transmitter: HDMI Type-A female connector
for connecting to the HDMI source.
Receiver: HDMI Type-A female connector for
video output.
3Audio In 3.5mm jack for connecting an external active
microphone.
4Audio Out 3.5mm jack for connecting an active loud
speaker.
5DC 12V
12V/2A DC power input.
Only use one power source, either from DC or
from 802.3af/at PoE+ Ethernet switch.
6ACT/Link
ACT: ACT LED indicator turns blue when
the device is powered up.
 Link: Link LED indicator ickers green
when network connection is waiting for
video source, turns green when network
connection and video source is functioning
properly.
7RS-232 DB-9 female connector for RS-232
bi-directional remote extension.
8IR
Transmitter: 3.5mm jack for IR emitter cable
to control video source device.
Receiver: 3.5mm jack for IR receiver cable to
receive signal from remote controller.
9PC USB USB Host Input Port.
10 Group Group conguration, 4-bit switch for 16
stream channel selection.
11 Reset
This button supports two functions: “Restore
to factory default setting” and “Stop
connecting to video source”.
Position Description Function
11 Reset
Restore to factory default setting:
1. Turn on the device rst.
2. Press and hold the button for over 15
seconds. Once the device is operational
again, it has restored to default settings.
Stop connecting to video source:
1. Turn on the device rst.
2. Press and hold the button for 1 second,
the link LED will turn off, the device does
not connect to video source.
3. Press and hold the button for 1 second
again, the link LED will turn on, the device
will connect to video source again.
12 G/V Mode
Press the button for 1 second to select
Graphic Mode or Video Mode (also deploy
to all the IHD-410PT and IHD-410PR of the
same channel).
13 VGA Out DB9 connector for VGA local display.
14 USB
USB ports for additional USB devices such
as USB mouse, USB keyboard and USB pen
drive.
Installation
1. Connect the video source to the Transmitter/Sender (IHD-410PT)
Unit’s HDMI In interface.
2. Connect the monitor to the Receiver (IHD-410PR) Unit’s HDMI Out
interface.
3. Set an identical ID number on DIP switch for all units of the same
group.

– 1 –
– 3 –
– 2 –
– 4 –
6 7 8 10911 12 13
Transmitter (IHD-410PT)
1 2 3 4 5
6 7 8 10 11 12 14
Receiver (IHD-410PR)
Position Description Function
1Ethernet
(PoE)
Connect to a LAN Switch.
IGMP snooping and Jumbo Frame
supported Gigabit IEEE 802.3af/at PoE+
Ethernet switch is recommended.
LED:
1. LAN LED (green color):
This LED will be ashing while network is
accessing via Ethernet.
2. Power LED (orange color):
When the device is powered on, and the
device is connected to Ethernet switch, the
LED will be always on.
Verify The Contents Inside Package Box
The package should contain the following items plus IHD-410 series. If
any item is missing or damaged, please contact the seller immediately.
Quick Installation Guide IR Emitter Cable
(Comes with Transmitter)
IR Receiver Cable
(Comes with Receiver)
Mounting Bracket Screws
Product Outlook & Functions
1 2 3 4 5
Position Description Function
2HDMI
Transmitter: HDMI Type-A female connector
for connecting to the HDMI source.
Receiver: HDMI Type-A female connector for
video output.
3Audio In 3.5mm jack for connecting an external active
microphone.
4Audio Out 3.5mm jack for connecting an active loud
speaker.
5DC 12V
12V/2A DC power input.
Only use one power source, either from DC or
from 802.3af/at PoE+ Ethernet switch.
6ACT/Link
ACT: ACT LED indicator turns blue when
the device is powered up.
 Link: Link LED indicator ickers green
when network connection is waiting for
video source, turns green when network
connection and video source is functioning
properly.
7RS-232 DB-9 female connector for RS-232
bi-directional remote extension.
8IR
Transmitter: 3.5mm jack for IR emitter cable
to control video source device.
Receiver: 3.5mm jack for IR receiver cable to
receive signal from remote controller.
9PC USB USB Host Input Port.
10 Group Group conguration, 4-bit switch for 16
stream channel selection.
11 Reset
This button supports two functions: “Restore
to factory default setting” and “Stop
connecting to video source”.
Position Description Function
11 Reset
Restore to factory default setting:
1. Turn on the device rst.
2. Press and hold the button for over 15
seconds. Once the device is operational
again, it has restored to default settings.
Stop connecting to video source:
1. Turn on the device rst.
2. Press and hold the button for 1 second,
the link LED will turn off, the device does
not connect to video source.
3. Press and hold the button for 1 second
again, the link LED will turn on, the device
will connect to video source again.
12 G/V Mode
Press the button for 1 second to select
Graphic Mode or Video Mode (also deploy
to all the IHD-410PT and IHD-410PR of the
same channel).
13 VGA Out DB9 connector for VGA local display.
14 USB
USB ports for additional USB devices such
as USB mouse, USB keyboard and USB pen
drive.
Installation
1. Connect the video source to the Transmitter/Sender (IHD-410PT)
Unit’s HDMI In interface.
2. Connect the monitor to the Receiver (IHD-410PR) Unit’s HDMI Out
interface.
3. Set an identical ID number on DIP switch for all units of the same
group.

– 1 –
– 3 –
– 2 –
– 4 –
6 7 8 10911 12 13
Transmitter (IHD-410PT)
1 2 3 4 5
6 7 8 10 11 12 14
Receiver (IHD-410PR)
Position Description Function
1Ethernet
(PoE)
Connect to a LAN Switch.
IGMP snooping and Jumbo Frame
supported Gigabit IEEE 802.3af/at PoE+
Ethernet switch is recommended.
LED:
1. LAN LED (green color):
This LED will be ashing while network is
accessing via Ethernet.
2. Power LED (orange color):
When the device is powered on, and the
device is connected to Ethernet switch, the
LED will be always on.
Verify The Contents Inside Package Box
The package should contain the following items plus IHD-410 series. If
any item is missing or damaged, please contact the seller immediately.
Quick Installation Guide IR Emitter Cable
(Comes with Transmitter)
IR Receiver Cable
(Comes with Receiver)
Mounting Bracket Screws
Product Outlook & Functions
1 2 3 4 5
Position Description Function
2HDMI
Transmitter: HDMI Type-A female connector
for connecting to the HDMI source.
Receiver: HDMI Type-A female connector for
video output.
3Audio In 3.5mm jack for connecting an external active
microphone.
4Audio Out 3.5mm jack for connecting an active loud
speaker.
5DC 12V
12V/2A DC power input.
Only use one power source, either from DC or
from 802.3af/at PoE+ Ethernet switch.
6ACT/Link
ACT: ACT LED indicator turns blue when
the device is powered up.
 Link: Link LED indicator ickers green
when network connection is waiting for
video source, turns green when network
connection and video source is functioning
properly.
7RS-232 DB-9 female connector for RS-232
bi-directional remote extension.
8IR
Transmitter: 3.5mm jack for IR emitter cable
to control video source device.
Receiver: 3.5mm jack for IR receiver cable to
receive signal from remote controller.
9PC USB USB Host Input Port.
10 Group Group conguration, 4-bit switch for 16
stream channel selection.
11 Reset
This button supports two functions: “Restore
to factory default setting” and “Stop
connecting to video source”.
Position Description Function
11 Reset
Restore to factory default setting:
1. Turn on the device rst.
2. Press and hold the button for over 15
seconds. Once the device is operational
again, it has restored to default settings.
Stop connecting to video source:
1. Turn on the device rst.
2. Press and hold the button for 1 second,
the link LED will turn off, the device does
not connect to video source.
3. Press and hold the button for 1 second
again, the link LED will turn on, the device
will connect to video source again.
12 G/V Mode
Press the button for 1 second to select
Graphic Mode or Video Mode (also deploy
to all the IHD-410PT and IHD-410PR of the
same channel).
13 VGA Out DB9 connector for VGA local display.
14 USB
USB ports for additional USB devices such
as USB mouse, USB keyboard and USB pen
drive.
Installation
1. Connect the video source to the Transmitter/Sender (IHD-410PT)
Unit’s HDMI In interface.
2. Connect the monitor to the Receiver (IHD-410PR) Unit’s HDMI Out
interface.
3. Set an identical ID number on DIP switch for all units of the same
group.

– 5 – – 6 –
4. Connect the USB cables from Transmitter to PC, and connect the USB
additional devices such as USB mouse, USB keyboard and USB pen
drive to Receiver.
5. Use Cat5e/6 cables (EIA/TIA 568B industry standard compliant) for
connection between Transmitter/Receiver and the IEEE 802.3af/at
PoE+ switch.
6. Apply the proper power to all connecting devices.
7. Connect the IR emitter cable with Transmitter and the IR receiver
cable with Receiver for remote control.
Note
It is suggested using the Gigabit IEEE 802.3af/at PoE+
Ethernet switch with IGMP Snooping and Jumbo Frame
to ensure optimal transmission quality.
If users encounter no screen display in computer
connection:
1. Make sure the device cables are correctly and rmly
attached.
2. Set your display device’s (TV, monitor, etc.) input
source as HDMI.
3. Check the PC BIOS conguration about the video
output setting.
4. Connect your computer to the HDMI Display
DIRECTLY to check if the video signal gets through.
Connection Pattern
1. Point to Point:
Video Extender
* More PoE switches and RXs (Receivers) can be used to distribute a single video signal to multi-monitors.
STEP 3STEP 1 STEP 2
Input Source Output Source Link
Video Source
1000BASE-T UTP
IHD-410PR
IHD-410PT IHD-410PR
IHD-410PT
HDMI HDMI
2. Multicasting:
USB
Video
USB
Video
USB
Video
USB
Video
USB
Video
Gigabit PoE Switch
(with IGMP Snooping and Jumbo Frame)
IHD-410PT (Transmitter 1)
IHD-410PR
(Receiver 1) IHD-410PR
(Receiver 2)
IHD-410PR
(Receiver 3)
IHD-410PR
(Receiver 4) IHD-410PR
(Receiver 5)
USB
Video
IHD-410PT (Transmitter 2)
USB
Video
IHD-410PT (Transmitter 3)
USB
Video
IHD-410PT (Transmitter 4)
USB
Video
IHD-410PT (Transmitter 5)
USB
Video
PoE
1000BASE-T UTP with PoE
USB Line
USB
Video Line
Video
PoE
PoE
PoE
PoE
PoE
PoE
PoE
PoE
PoE
PoE
PC/Server
PC/Server
PC/Server
PC/Server
PC/Server
Multiple HDMIs and USB over IP Interaction Application
Further Conguration
For detailed conguration, please refer to user manual downloadable
from the web site. (http://www.planet.com.tw/en/support/download.php).
User’s Manual
If you have any other question, please contact the dealer where
you purchased this product or you can contact PLANET directly at the
following email address: [e-mail]

– 5 – – 6 –
4. Connect the USB cables from Transmitter to PC, and connect the USB
additional devices such as USB mouse, USB keyboard and USB pen
drive to Receiver.
5. Use Cat5e/6 cables (EIA/TIA 568B industry standard compliant) for
connection between Transmitter/Receiver and the IEEE 802.3af/at
PoE+ switch.
6. Apply the proper power to all connecting devices.
7. Connect the IR emitter cable with Transmitter and the IR receiver
cable with Receiver for remote control.
Note
It is suggested using the Gigabit IEEE 802.3af/at PoE+
Ethernet switch with IGMP Snooping and Jumbo Frame
to ensure optimal transmission quality.
If users encounter no screen display in computer
connection:
1. Make sure the device cables are correctly and rmly
attached.
2. Set your display device’s (TV, monitor, etc.) input
source as HDMI.
3. Check the PC BIOS conguration about the video
output setting.
4. Connect your computer to the HDMI Display
DIRECTLY to check if the video signal gets through.
Connection Pattern
1. Point to Point:
Video Extender
* More PoE switches and RXs (Receivers) can be used to distribute a single video signal to multi-monitors.
STEP 3STEP 1 STEP 2
Input Source Output Source Link
Video Source
1000BASE-T UTP
IHD-410PR
IHD-410PT IHD-410PR
IHD-410PT
HDMI HDMI
2. Multicasting:
USB
Video
USB
Video
USB
Video
USB
Video
USB
Video
Gigabit PoE Switch
(with IGMP Snooping and Jumbo Frame)
IHD-410PT (Transmitter 1)
IHD-410PR
(Receiver 1) IHD-410PR
(Receiver 2)
IHD-410PR
(Receiver 3)
IHD-410PR
(Receiver 4) IHD-410PR
(Receiver 5)
USB
Video
IHD-410PT (Transmitter 2)
USB
Video
IHD-410PT (Transmitter 3)
USB
Video
IHD-410PT (Transmitter 4)
USB
Video
IHD-410PT (Transmitter 5)
USB
Video
PoE
1000BASE-T UTP with PoE
USB Line
USB
Video Line
Video
PoE
PoE
PoE
PoE
PoE
PoE
PoE
PoE
PoE
PoE
PC/Server
PC/Server
PC/Server
PC/Server
PC/Server
Multiple HDMIs and USB over IP Interaction Application
Further Conguration
For detailed conguration, please refer to user manual downloadable
from the web site. (http://www.planet.com.tw/en/support/download.php).
User’s Manual
If you have any other question, please contact the dealer where
you purchased this product or you can contact PLANET directly at the
following email address: [email protected]

– 5 – – 6 –
4. Connect the USB cables from Transmitter to PC, and connect the USB
additional devices such as USB mouse, USB keyboard and USB pen
drive to Receiver.
5. Use Cat5e/6 cables (EIA/TIA 568B industry standard compliant) for
connection between Transmitter/Receiver and the IEEE 802.3af/at
PoE+ switch.
6. Apply the proper power to all connecting devices.
7. Connect the IR emitter cable with Transmitter and the IR receiver
cable with Receiver for remote control.
Note
It is suggested using the Gigabit IEEE 802.3af/at PoE+
Ethernet switch with IGMP Snooping and Jumbo Frame
to ensure optimal transmission quality.
If users encounter no screen display in computer
connection:
1. Make sure the device cables are correctly and rmly
attached.
2. Set your display device’s (TV, monitor, etc.) input
source as HDMI.
3. Check the PC BIOS conguration about the video
output setting.
4. Connect your computer to the HDMI Display
DIRECTLY to check if the video signal gets through.
Connection Pattern
1. Point to Point:
Video Extender
* More PoE switches and RXs (Receivers) can be used to distribute a single video signal to multi-monitors.
STEP 3STEP 1 STEP 2
Input Source Output Source Link
Video Source
1000BASE-T UTP
IHD-410PR
IHD-410PT IHD-410PR
IHD-410PT
HDMI HDMI
2. Multicasting:
USB
Video
USB
Video
USB
Video
USB
Video
USB
Video
Gigabit PoE Switch
(with IGMP Snooping and Jumbo Frame)
IHD-410PT (Transmitter 1)
IHD-410PR
(Receiver 1) IHD-410PR
(Receiver 2)
IHD-410PR
(Receiver 3)
IHD-410PR
(Receiver 4) IHD-410PR
(Receiver 5)
USB
Video
IHD-410PT (Transmitter 2)
USB
Video
IHD-410PT (Transmitter 3)
USB
Video
IHD-410PT (Transmitter 4)
USB
Video
IHD-410PT (Transmitter 5)
USB
Video
PoE
1000BASE-T UTP with PoE
USB Line
USB
Video Line
Video
PoE
PoE
PoE
PoE
PoE
PoE
PoE
PoE
PoE
PoE
PC/Server
PC/Server
PC/Server
PC/Server
PC/Server
Multiple HDMIs and USB over IP Interaction Application
Further Conguration
For detailed conguration, please refer to user manual downloadable
from the web site. (http://www.planet.com.tw/en/support/download.php).
User’s Manual
If you have any other question, please contact the dealer where
you purchased this product or you can contact PLANET directly at the
following email address: [e-mail]