Samsung PM32F User manual

Quick Setup Guide
PM32F·PM43F·PM49F·PM55F
PH43F·PH49F·PH55F
• The colour and the appearance may differ depending on the product, and the specications are subject
to change without priornotice to improve the performance.
• Download the user manual from the website for further details.
http://www.samsung.com/displaysolutions
The terms HDMI and HDMI High-Denition Multimedia Interface, and the HDMI Logo are
trademarks or registered trademarks of HDMI Licensing LLC in the United States and other
countries. BN68-08079J-00
Checking the Components
Contact the vendor where you purchased the product if any components are missing.
Quick Setup Guide Warranty card (Not available in some
locations)
Regulatory guide MagicInfo Software DVD
+
+
-
-
Power cord Batteries (Not available in some locations) Remote Control RS232C(IN) adapter
Screw (M3L8, 1 piece) USB cover
Troubleshooting Guide
Reverse Side
DVI / RGB /
MAGICINFO IN
HDMI2
USB1
RS232C
OUT
RS232C
IN
USB2
AUDIO
IN
HDMI1
AUDIO
OUT
RJ45DP IN DAISY CHAIN
01 03 04 0602 05
07 08 09
01 Connect to a USB memory device.
02 Connects to MDC using an RS232C adapter.
03 Receives sound from a source device via an audio cable.
04 Connects to the audio of a source device.
05 Connects to a source device using an HDMI cable.
06 DVI IN: Connects to a source device using a DVI cable or HDMI-DVI cable.
RGB IN: Use the (dedicated) D-SUB - DVI cable (or D-SUB cable with D-SUB to DVI
adapter) when connecting a PC.
MAGICINFO IN: Use the (dedicated) DP-DVI cable when connecting a network box
(sold separately).
07 Connects to a source device using a DP cable.
08 Connects to another product using a daisy chain (DP port) cable.
09 Connects to MDC using a LAN cable.
Issues Solutions
The screen keeps switching
on and off.
Check the cable connection between the product
and PC, and ensure the connection is secure.
No Signal is displayed on the
screen.
Check that the product is connected correctly with
a cable.
Check that the device connected to the product is
powered on.
Not Optimum Mode is
displayed.
This message is displayed when a signal from the
graphics card exceeds the product’s maximum
resolution and frequency.
Refer to the Standard Signal Mode Table and set
the maximum resolution and frequency according
to the product specications.
The images on the screen
look distorted.
Check the cable connection to the product.
The screen is not clear.
The screen is blurry.
Adjust Coarse and Fine.
Remove any accessories (video extension cable,
etc) and try again.
Set the resolution and frequency to the
recommended level.
The screen appears unstable
and shaky.
Check that the resolution and frequency of the
PC and graphics card are set within a range
compatible with the product. Then, change the
screen settings if required by referring to the
Additional Information on the product menu and
the Standard Signal Mode Table.
There are shadows orghost
images left on the screen.
Issues Solutions
The screen is too bright.
The screen is too dark.
Adjust Brightness and Contrast.
Screen color is inconsistent. Go to Picture and adjust the ColorSpace settings.
White does not really look
white.
Go to Picture and adjust the White Balance settings.
There is no sound. Check the connection of the audio cable or adjust
the volume.
Check the volume.
The volume is too low. Adjust the volume.
If the volume is still low afterturning it up to the
maximum level, adjust the volume on your PC
sound card or software program.
The remote control does not
work.
Make sure that the batteries are correctly in place
(+/-).
Check if the batteries are at.
Check for power failure.
Make sure that the power cord is connected.
Check for any special lighting or neon signs
switched on in the vicinity.
[PMF_PM32~55-INDIA-QSG]BN68-08079J-00.indd 1 8/22/2016 4:22:33 PM

Connecting and Using a Source Device
Connecting to a PC
DVI / RGB / MAGICINFO IN
AUDIO IN
DVI / RGB / MAGICINFO IN
AUDIO IN
HDMI1 or HDMI2
AUDIO IN
HDMI1 or HDMI2
DP IN
Connecting an External Monitor
DAISY CHAIN
Connecting to a Video Device
HDMI1 or HDMI2
AUDIO IN
HDMI1 or HDMI2
Connecting to an Audio System
AUDIO OUT
Connecting the LAN Cable
RJ45
Use Cat7(*STP Type) cable for the connection.
* Shielded Twist Pair
Connecting to MDC
RS232C IN
RS232C OUT
RS232C IN
RS232C OUT
RS232C IN
RS232C OUT
RJ45 HUB
RJ45
RS232C OUT
RS232C IN
RS232C OUT
RS232C IN
RS232C OUT
• For details on how to use the MDC programme, refer to Help after installing
the programme.
• The MDC programme is available on the website.
Specications
Model Name PM32F PM43F / PH43F PM49F / PH49F PM55F / PH55F
Panel Size 80.1 cm 107.9 cm 123.2 cm 138.7 cm
Display area 698.4 mm (H) x 392.85 mm (V) 940.89 mm (H) x
529.25 mm (V)
1073.78 mm (H) x
604.00 mm (V)
1209.6 mm (H) x 680.4 mm (V)
Audio Output 10 W + 10 W 10 W + 10 W 10 W + 10 W 10 W + 10 W
Power Supply AC 100 to 240 VAC (+/- 10%), 60 / 50 Hz ± 3 Hz
Refer to the label at the back of the product as the standard voltage can vary in different countries.
Environmental
considerations
Operating Temperature: 0 ˚C - 40 ˚C (32 ˚F - 104 ˚F), With PIM: 10 ˚C - 40 ˚C (50 ˚F - 104 ˚F)
Humidity: 10% - 80%, non-condensing
Storage Temperature: -20 ˚C - 45 ˚C (-4 ˚F - 113 ˚F)
Humidity: 5% - 95%, non-condensing
• This device is a Class A digital apparatus.
Warning! Important Safety Instructions
(Please read the appropriate section that corresponds to the marking onyourSamsung product before attempting to install the product.)
CAUTION
RISK OF ELECTRIC SHOCK DO NOTOPEN
CAUTION: TO REDUCE THE RISKOF ELECTRIC SHOCK, DO NOTREMOVE COVER (OR
BACK). THERE ARE NO USER SERVICEABLE PARTS INSIDE. REFER ALLSERVICING TO
QUALIFIED PERSONNEL.
This symbol indicates that highvoltage is present inside. It is dangerousto
make any kind of contactwith anyinternal part of this product.
This symbol alerts you that important literature concerning operation and
maintenance has been included with this product.
• If your equipment uses an AC adapter:
‒ Only use the AC adapter with your product by Samsung.
‒ Do not use the powercordwith other products.
• Do not install this equipment in a conned space such as a case or similar.
• The slots and openings in the cabinet and in the back or bottom are provided for necessary
ventilation. The slots and openings must never be blocked or covered.
• The product should be located away from heat sources such as radiators, heat registers, or
other products that produce heat.
• Do not place a watercontainingvessel (vases etc.) on this apparatus, as this can result in a risk
of re or electric shock. (Apparatus shall not be exposed to dripping or splashing)
• The apparatus must be connected to an earthed MAINS socket-outlet (Class l Equipment only).
Or Use only a properly grounded plug and receptacle (Class l Equipment only).
• To disconnect the apparatus from the mains, the plug must be pulled out from the mains
socket, therefore the mains plug shall be readily operable.
• As long as this unit is connected to the AC wall outlet, it is not disconnected from the AC power
source even if you turn off this unit by POWER.
This product is RoHS compliant.
This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charger, headset, USB cable) should not be disposed of with other household
waste at the end of their working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate these items from other types of waste and
recycle
them responsibly to promote the sustainable reuse of material resources.
For more information on safe disposal and recycling visit our website www.samsung.com/in or contact our Helpline numbers -18002668282, 180030008282.
Contact SAMSUNG WORLD WIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care centre.
Tel. [phone] - Toll Free
1800 266 8282 - Toll Free
www.samsung.com/in/support
Ⓡ
Ⓡ
[PMF_PM32~55-INDIA-QSG]BN68-08079J-00.indd 2 8/22/2016 4:22:35 PM