Planet GS-5220-24P4X User manual

L2+ Managed PoE Switch
GS-5220 PoE Series
Quick Installation Guide

Table of Contents
1. Package Contents ....................................................................................... 3
2. Requirements ............................................................................................. 5
3. Terminal Setup ........................................................................................... 6
4. Logon to Console........................................................................................ 7
5. ConguringIPAddress................................................................................ 8
6. Starting Web Management .........................................................................10
7. SavingConguration..................................................................................13
8. RecoveringBacktoDefaultConguration.....................................................14
9. Customer Support .....................................................................................15

3
1. Package Contents
Thank you for purchasing PLANET GS-5220 Series Managed PoE Switch. The
descriptionofthismodelisshownbelow:
ModelName
Gigabit
RJ45
Ports
GigabitSFP
Slots
10G
SFP+
Slots
PoE
Power
Budget
System
Redundant
Power
GS-5220-24P4X 24 4 combo 4400W -
GS-5220-24P4XR 24 4 combo 4400W Yes
GS-5220-24PL4X 24 4 combo 4600W -
GS-5220-24PL4XR 24 4 combo 4600W Yes
GS-5220-48P4X 48 -4400W -
GS-5220-48P4XR 48 -4400W Yes
GS-5220-48PL4X 48 -4600W -
GS-5220-48PL4XR 48 -4600W Yes
“Managed PoE Switch” is used as an alternative name in this Quick Installation
Guide.

4
Open the box of the Managed Switch and carefully unpack it. The box should
containthefollowingitems:
zTheManagedPoESwitch
zQuickInstallationGuide
zRJ45 to RS232 Cable
zRubberFeet
zTwoRack-mountingBracketswithAttachmentScrews
zPowerCord
zSFPDust-proofCaps
Model SFPDust-proofCaps
GS-5220-24P4X 8
GS-5220-24P4XR 8
GS-5220-24PL4X 8
GS-5220-24PL4XR 8
GS-5220-48P4X 4
GS-5220-48P4XR 4
GS-5220-48PL4X 4
GS-5220-48PL4XR 4
If any item is found missing or damaged, please contact your local reseller for
replacement.

5
2. Requirements
zWorkstations running Windows 10/XP/2003/Vista/7/8/2008, MAC OS X or later,
Linux,UNIX,orotherplatformsarecompatiblewithTCP/IPprotocols.
zWorkstationsareinstalledwithEthernetNIC(NetworkInterfaceCard)
zSerial Port Connection (Terminal)
The above Workstations come with COM Port (DB9) or USB-to-RS232
converter.
TheaboveWorkstationshavebeeninstalledwith terminal emulator,suchas
HyperTerminalincludedinWindowsXP/2003.
Serial cable -- one end is attached to the RS232 serial port, while the other
endtotheconsoleportoftheManagedPoESwitch.
zEthernet Port Connection
Networkcables--Usestandardnetwork(UTP)cableswithRJ45connectors.
The above PC is installed with Web browser and JAVA runtime environment
plug-in.
Note
It is recommended to use Internet Explore 8.0 or above to access
the Managed Switch. If the Web interface of the Managed Switch
is not accessible, please turn off the anti-virus software or firewall
andthentryitagain.

6
3. Terminal Setup
To congure the system, connect a serial cable to a COM port on a PC or
notebookcomputerandtoRJ45typeofserialportoftheManagedSwitch.
Managed Switch
PC / Workstation
with
Terminal Emulation Software
Serial Port
RS232 to RJ45 Cable
Console Port
RJ45
Figure 3-1 Managed Switch Console Connectivity
A terminal program is required to make the software connection to the Managed
Switch.
1. Run terminal program on the OS.
2.When the following screen appears, make sure that the COM port should be
conguredas:
Baud:115200
Databits:8
Parity:None
Stopbits:1
Flowcontrol:None
Figure 3-2 COM Port Conguration

7
4. Logon to Console
Once the terminal is connected to the device, power on the Managed Switch, and
the terminal will display “running testing procedures”. Then, the following message
asks to log in user name and password. The factory default user name and
passwordareshownasfollowsandtheloginscreeninFigure4-1appears.
Username:admin
Password:admin
Figure 4-1: Managed PoE Switch Console Login Screen
The user can now enter commands to manage the Managed Switch. For a detailed
descriptionofthecommands,pleaserefertothefollowingchapters.
Note
1.For security reason, please change and memorize the new pass-
wordafterthisfirstsetup.
2.Only accept command in lowercase letter under console inter-
face.

8
5.ConguringIPAddress
TheManagedPoESwitchisshippedwithdefaultIPaddressshownbelow.
IPAddress:192.168.0.100
SubnetMask:255.255.255.0
To check the current IP address or modify a new IP address for the Switch, please
usetheproceduresasfollows:
Show the current IP Address
1.Atthe“#”prompt,enter“show ip interface brief”.
2.ThescreendisplaysthecurrentIPaddressasshowninFigure5-1.
Figure 5-1: IP Information Screen
Conguring IP Address
3.At the “#” prompt, enter the following command and press <Enter> as shown
inFigure5-2.
GS-5220Series# congure terminal
GS-5220Series(cong)# interface vlan 1
GS-5220Series(cong-if-vlan)# ip address 192.168.1.100 255.255.255.0
ThepreviouscommandwouldapplythefollowingsettingsfortheManagedSwitch.
IPAddress:192.168.1.100
SubnetMask:255.255.255.0
Figure 5-2: Conguring IP Address Screen
4.Repeatstep1tocheckiftheIPaddresshaschanged.

9
Store current switch conguration
5.Atthe“#”prompt,enterthefollowingcommandandpress<Enter>.
# copy running-cong startup-cong
Figure 5-3: Saving Current Conguration Command Screen
If the IP is successfully congured, the Managed Switch will apply the new IP
address setting immediately. You can access the Web interface of the Managed
SwitchthroughthenewIPaddress.
Note
If you are not familiar with the console command or the related
parameter,enter “help” anytimein console toget thehelp descrip-
tion.

10
6. Starting Web Management
The following shows how to start up the Web Management of the Managed
Switch. Note the Managed Switch is congured through an Ethernet connection.
Please make sure the manager PC must be set to the same IP subnet address.
For example, the default IP address of the Managed Switch is 192.168.0.100,
then the manager PC should be set to 192.168.0.x (where x is a number
between1and254,except100),andthedefaultsubnetmaskis255.255.255.0.
PC / Workstation
with Web Browser
192.168.0.x
Managed Switch
RJ45/UTP Cable
IP Address:
192.168.0.100
Figure 6-1: IP Management Diagram
Logging in to the Managed Switch
1.Use Internet Explorer 8.0 or above Web browser and enter IP address
http://192.168.0.100(thefactorydefaultIPaddressortheonethatyouhave
justchangedinconsole)toaccesstheWebinterface.
2.When the following dialog box appears, please enter the default user name and
password “admin” (or the password you have changed via console). The login
screeninFigure6-2appears.