Playcraft 1702 User manual

IMPORTANT NOTES: Read First
For Customer Service Call
800.333.8519 (U.S.A.) or
541.955.9199 (International)
Manufactured by Krauss Craft, Inc.
www.playcraftsystems.com
DOUBLE SLIDE
1702
Page 1 of 7
Rev E
7/18/2009
(A) Use liquid thread lock (such as Loctite
®
) with all threaded hardware. Important: Liquid thread lock (prior to
curing) helps to eliminate the common problem of "thread seizure" in stainless steel hardware by serving as a
lubricant during assembly.
(B) Do not pour concrete until the equipment is completely assembled, leveled and plumbed. Concrete must be
allowed to cure completely before using the equipment (at least 72 hours).
(C) Refer to Installation Manual Section R5-1305 Double Sit Down Bar and R3.5-1305 Double Sit Down Panel.
(D) Exit height must be between 7" [180mm] and 15" [380mm] from finish grade for slides with an elevation
greater than 48". For slide elevations no greater than 48", the exit height shall be no greater than 11".
Exit region must also have a downward slope of 0 to 4°.
(E) Use appropriate compliant protective surfacing and adjust footing depths accordingly. See free publication -
The Handbook for Public Playground Safety, Publication #325 at www.CPSC.gov for the surfacing appropriate for
the fall height of the equipment or consult you surfacing supply representative.
60" Double Slide
FIGURE 1
NOTE: R5 60" Double Slide shown.
R3.5 may vary slightly, but does not
affect assembly instructions.
R5-1305 Double Sit-Down Bar or
Figure 1.1
See Installation Manual Sections
R3.5-1305 Double Sit Down Panel
Figures 1.3 and 1.4
Figure 1.2
See Footing Detail

For Customer Service Call
800.333.8519 (U.S.A.) or
541.955.9199 (International)
Manufactured by Krauss Craft, Inc.
www.playcraftsystems.com
DOUBLE SLIDE
1702
Page 2 of 7
Rev E
7/18/2009
Footing Detail
(Finish Grade)
(Top of Soil) (Top of Soil)
Step 1
Refer to corresponding Footing Layout and mark footing
hole locations. Dig (2) Ø 12" and (1) 12" x 24" footing
hole(s). Refer to Footing Detail for depth and details.
Note: For 36" Double Slide dig only (2) Ø 12" footing
holes.
IMPORTANT: For areas with soft soil conditions, larger
footings may be required.
* Footing depth must be adjusted to compensate for the
depth/thickness requirements of selected safety
surfacing. See Section 06.1 of the Installation Manual
** Adjust footing depth with blocking to meet required
exit height. (See Note D)
(Finish Grade)
Footing Depth Dimensions
Support Leg
Deck Height SD1* SD2** LD1* LD2**
30" NA NA 31 1/2" [800mm] 22 1/2" [572mm]
36" NA NA 25 1/2" [648mm] 16 1/2" [419mm]
42" 41" [1041mm] 32" [813mm] 30" [762mm] 21" [533mm]
48" 35" [889mm] 26" [660mm] 24" [610mm] 15" [381mm]
54" 40" [1016mm] 31" [787mm] 30" [762mm] 21" [533mm]
60" 34" [864mm] 25" [635mm] 24" [610mm] 15" [381mm]
66" 35 1/2" [902mm] 26 1/2" [673mm] 27" [686mm] 18" [457mm]
72" 29 1/2" [749mm] 20 1/2" [521mm] 21" [533mm] 12" [305mm]
Footing Anchor
Concrete Footing
(welded 5/8" Rod)
(See Note D)
Undisturbed Soil
2b Stone, drain rock
Compacted depth shown
Pea Gravel (for drainage)
Optional Filter Fabric Over
LOOSE FILL GROUND COVER:
Impact attenuating (resilient)
surfacing 9" Compacted or
12" uncompressed depth,
Blocking, See
Installers Manual
SD1* SD2**
LD1*
LD2**
See Note D
For Exit Height

For Customer Service Call
800.333.8519 (U.S.A.) or
541.955.9199 (International)
Manufactured by Krauss Craft, Inc.
www.playcraftsystems.com
DOUBLE SLIDE
1702
Page 3 of 7
Rev E
7/18/2009
9
316
"
233mm
9
316
"
233mm
18
516
"
466mm
57
516
"
1456mm
9
316
"
233mm
9
316
"
233mm
R5 Top View - Footing Layouts
36" Double Slide
48" Double Slide
60" Double Slide
72" Double Slide
40
716
"
1027mm
99
1516
"
2538mm
18
516
"
466mm
46"
1168mm
101
316
"
2570mm
18
516
"
466mm
34
1316
"
884mm
82
58
"
2099mm
18
516
"
466mm

For Customer Service Call
800.333.8519 (U.S.A.) or
541.955.9199 (International)
Manufactured by Krauss Craft, Inc.
www.playcraftsystems.com
DOUBLE SLIDE
1702
Page 4 of 7
Rev E
7/18/2009
18
516
"
466mm
9
316
"
233mm
41
1516
"
1065mm
101
716
"
2577mm
9
316
"
233mm
47
12
"
1207mm
102
1116
"
2609mm
9
316
"
233mm
58
1316
"
1494mm 18
516
"
466mm
9
316
"
233mm
R3.5 Top View - Footing Layouts
36" Double Slide
48" Double Slide
60" Double Slide
72" Double Slide
36
516
"
922mm
84
18
"
2137mm
18
516
"
466mm
18
516
"
466mm

For Customer Service Call
800.333.8519 (U.S.A.) or
541.955.9199 (International)
Manufactured by Krauss Craft, Inc.
www.playcraftsystems.com
DOUBLE SLIDE
1702
Page 5 of 7
Rev E
7/18/2009
Figure 1.3
Step 2
Attach Double Slide Leg to the base of the double slide
as shown in Figure 1.1. (See Note A)
Step 3
Note: This step does not apply to the 36" Double Slide.
Attach slide supports to the double slide as shown in
Figure 1.2. (See Note A)
Step 4
For R5 Double Slide only
Place the Double Slide Leg and Supports into the
footing holes and attach the face of the double slide
to the face of the R5 deck as shown in Figure 1.3.
(See Note A)
For R3.5 Double Slide only
Place the Double Slide Leg and Supports into the
footing holes and attach the double slide and the
R3.5 Double Slide Spacer to the face of the R3.5
deck as shown in Figure 1.4. (See Note A)
DOUBLE
Nut
Button Head Bolt
3/8" x 1-3/4"
SLIDE
3/8" x 1" O.D.
Washer
3/8" Lock
R5 Deck
3/8" x 3/4" Button
Head Bolt
Figure 1.2
3/8" x 1" O.D.
Washer
SLIDE
DOUBLE
SLIDE SUPPORT
DOUBLE SLIDE LEG
Figure 1.1
3/8 x 3/4" Hex Bolt
3/8" x 1" O.D. Washer
DOUBLE SLIDE
Figure 1.4
SLIDE
Button Head Bolt
3/8" x 3-1/4"
SPACER
SLIDE
Nut
3/8" Lock
3/8" x 1" O.D.
Washer
DOUBLE
R3.5 Deck

Manufactured by Krauss Craft, Inc.
www.playcraftsystems.com
For Customer Service Call
800.333.8519 (U.S.A.) or
541.955.9199 (International)
DOUBLE SLIDE
Rev E
7/18/2009
1702
Page 6 of 7
DOUBLE SLIDE SPACER:
Shall be fabricated using punched and formed 12
gauge sheet Steel. The Double Slide Spacer shall
be Play-Tuff™ coated after fabrication.
DOUBLE SLIDE:
Shall be constructed of UV-stabilized, rotationally
molded linear low density polyethylene with an
average wall thickness of 1/4" with a molded in
footing base.
DOUBLE SLIDE LEG:
Shall be fabricated of (2) 1.660" O.D. 11 gauge steel
tubing welded onto a 3/16" plate steel with a 5/8"
steel rod welded to the base as a footing anchor. The
Double Slide Leg has a multi-stage baked-on powder
coat finish.
SLIDE SUPPORT:
Shall be fabricated of 1.660" O.D., 11 gauge steel
tubing welded onto a 3/16" steel plate with a 5/8"
steel rod welded to the base as a footing anchor. The
Slide Support has a multi-stage baked-on powder
coat finish.
HARDWARE:
Shall be stainless steel, zinc/nickel plated or
galvanized as required to resist rust and corrosion.
Specifications
Step 5
Fully tighten all fasteners according to the
"TIGHTENING TORQUE FOR HARDWARE"
section of the Installation Manual.
Step 6
Plumb and level entire component. Pour concrete
into footing hole. Allow at least 72 hours to cure
before using this equipment. (See Note B and D)
Step 7
Place appropriate compliant protective surfacing
under and around the Double Slide. (See Note E)
36" Double Slide
48" Double Slide
R5 Parts List
Part # DESCRIPTION QTY.
DE-4224 Double Slide 36-42 1
FS-1702 Double Slide Leg 1
9103082-TR Bolt Button Head 3/8" x 1-3/4" 6
9123032 Bolt Hex 3/8" x 3/4" 3
9333002 Washer Flat 3/8" x 1" O.D. x .100" thick 15
9413002 Nut Lock 3/8" 6
R3.5 Parts List
Part # DESCRIPTION QTY.
CG-8128 Slide Spacer R3.5 1
DE-4224 Double Slide 36-42 1
FS-1702 Double Slide Leg 1
9103142-TR Bolt Button Head 3/8" x 3-1/4" 6
9123032 Bolt Hex 3/8" x 3/4" 3
9333002 Washer Flat 3/8" x 1" O.D. x .100" thick 15
9413002 Nut Lock 3/8" 6
R5 Parts List
Part # DESCRIPTION QTY.
DE-4400 Wave Slide Double 48 1
FS-1702 Double Slide Leg 1
FS-1704 Wave Slide Support 2
9103032-TR Bolt Button Head 3/8" x 3/4" 4
9103082-TR Bolt Button Head 3/8" x 1-3/4" 6
9123032 Bolt Hex 3/8" x 3/4" 3
9333002 Washer Flat 3/8" x 1" O.D. x .100" thick 19
9413002 Nut Lock 3/8" 6
R3.5 Parts List
Part # DESCRIPTION QTY.
CG-8128 Slide Spacer R3.5 1
DE-4400 Wave Slide Double 48 1
FS-1702 Double Slide Leg 1
FS-1704 Wave Slide Support 2
9103032-TR Bolt Button Head 3/8" x 3/4" 4
9103142-TR Bolt Button Head 3/8" x 3-1/4" 6
9123032 Bolt Hex 3/8" x 3/4" 3
9333002 Washer Flat 3/8" x 1" O.D. x .100" thick 19
9413002 Nut Lock 3/8" 6

Manufactured by Krauss Craft, Inc.
www.playcraftsystems.com
For Customer Service Call
800.333.8519 (U.S.A.) or
541.955.9199 (International)
DOUBLE SLIDE
1702
Page 7 of 7
Rev E
7/18/2009
Periodically tighten all screws, bolts and nuts. A
periodic inspection of all parts is necessary. If a part
is broken or worn, replace immediately. For general
maintenance please refer to our Playground
Maintenance Manual.
Maintenance
60" Double Slide 72" Double Slide
R5 Parts List
Part # DESCRIPTION QTY.
DE-4806 60" Doulbe Slide 1
FS-1702 Double Slide Leg 1
FS-1704 Wave Slide Support 2
9103032-TR Bolt Button Head 3/8" x 3/4" 4
9103082-TR Bolt Button Head 3/8" x 1-3/4" 6
9123032 Bolt Hex 3/8" x 3/4" 3
9333002 Washer Flat 3/8" x 1" O.D. x .100" thick 19
9413002 Nut Lock 3/8" 6
R3.5 Parts List
Part # DESCRIPTION QTY.
CG-8128 Slide Spacer R3.5 1
DE-4806 60" Doulbe Slide 1
FS-1702 Double Slide Leg 1
FS-1704 Wave Slide Support 2
9103032-TR Bolt Button Head 3/8" x 3/4" 4
9103142-TR Bolt Button Head 3/8" x 3-1/4" 6
9123032 Bolt Hex 3/8" x 3/4" 3
9333002 Washer Flat 3/8" x 1" O.D. x .100" thick 19
9413002 Nut Lock 3/8" 6
R5 Parts List
Part # DESCRIPTION QTY.
DE-4324 72" Double Slide 1
FS-1702 Double Slide Leg 1
FS-1704 Wave Slide Support 2
9103032-TR Bolt Button Head 3/8" x 3/4" 4
9103082-TR Bolt Button Head 3/8" x 1-3/4" 6
9123032 Bolt Hex 3/8" x 3/4" 3
9333002 Washer Flat 3/8" x 1" O.D. x .100" thick 19
9413002 Nut Lock 3/8" 6
R3.5 Parts List
Part # DESCRIPTION QTY.
CG-8128 Slide Spacer R3.5 1
DE-4324 72" Double Slide 1
FS-1702 Double Slide Leg 1
FS-1704 Wave Slide Support 2
9103032-TR Bolt Button Head 3/8" x 3/4" 4
9103142-TR Bolt Button Head 3/8" x 3-1/4" 6
9123032 Bolt Hex 3/8" x 3/4" 3
9333002 Washer Flat 3/8" x 1" O.D. x .100" thick 19
9413002 Nut Lock 3/8" 6