Playzone 2 BAY SWING BEAM User manual

Rope Swing
Chain Swing
Trapeze Swing
Baby Swing
4 5
11
6
3
1
8
10
12 13
14
9
7
2
15
16
ASSEMBLY INSTRUCTIONS - 2 BAY SWING BEAM
PARTS/REQUIREMENTS LIST
2 Bay Swing Beam Parts List
Item Description Qty
1 Swing Beam 1
2 Beam Support Leg 2
3 Beam Support Brace 1
4 Fixing Beam 1
5 Stabilising Peg 2
6 Swing
(Type Depends On Ordered)
2
7 Beam Support Bracket 2
8 M8 x 110mm Coach Bolt 1
9 M10 x 200mm Coach Bolt 3
10 14G x 75mm Bugle Phil Screw 6
11 12G x 32mm Pan Square Screw 20
12 M8 Hex Nut 1
13 M10 Hex Nut 3
14 M8 Flat Washer 1
15 M10 Flat Washer 3
16 Fixing Protector Base & Cap Set 4
Tools Required
1 Battery Drill (Atleast 14.4v)
2
3mm x 50mm Square Drive Bit
(Supplied With Tower Pack)
3
5mm x 50mm Hex Drive Bit
(Supplied With Tower Pack)
4 13mm Spanner/Crescent/Socket
5 17mm Spanner/Crescent/Socket
6 Level
7 Hammer
8 Spade
9 Ladder
Additional Info
Allow Roughly 1 Hour For Two Adults To Assemble
Two Bay Swing Beam Assembly
SHEET 1 OF 3 Version:

A
B
STEP 1:
Beam Support Frame
Instruction:
Position Support Legs Flush With Angle
Of Support Bracket (Detail A) & Fix In Place.
Fix Support Brace As Per Detail B.
2
2
3
DETAIL A
SCALE 1 : 8
Ensure Angle Of
Beam Support Legs
Match The Angle Of
The Support Bracket
Ensure The High Point
Of The Beam Support
Legs Are Flush With
The Top Of The
Support Bracket
7
11
DETAIL B
SCALE 1 : 8
Once Angle Of Beam
Support Legs Are
Correct, Fix Support Brace
Level Where It Sits Flush
(As Shown)
10
C
DETAIL C
SCALE 1 : 8
7
11
D
DETAIL D
SCALE 1 : 10
4
9
16
15
13
E
F
Instruction:
Stand The Beam Support Frame Up
& Secure The Swing Beam As
Shown Below. Leave Fixings
Loose Until Noted Otherwise.
1
DETAIL E
SCALE 1 : 10
1
16
14
12
8
DETAIL F
SCALE 1 : 10
9
16
15
13
STEP 2:
Beam Support Frame
Instruction:
Fix Second Support Bracket
On Opposite Side Of Frame,
Ensuring Bracket Faces Are Flush.
Instruction:
Secure Fixing Beam To The
Towers Top Set Of Holes
(As Shown).
Leave Fixings Loose Until
Noted Otherwise.
STEP 3:
Mounting Fixing Beam
STEP 4:
Attaching Swing Beam
** IMPORTANT **
Ensure The Bolts Are
Installed From The
Directions Detailed.
** IMPORTANT **
Ensure Beam Is Fixed Above
A Closed Barrier.
SHEET 2 OF 3 Version:

H
G
Instruction:
Dig Beam Support Frame Into Ground
Until Swing Beam Is Level. Ensure The
Support Frame Is Also Level, Then
Tighten The Fixings From The Previous
Steps. Once Completed, Install The
Remaining Screws To The Support
Brackets (Detail G), & Stake The Frame
To The Ground (As Per Detail H).
STEP 5:
Levelling Swing Beam
** IMPORTANT **
Finish Tower Assembly Before
Completing The Remaining
Steps Of The 2 Bay Swing Beam Assembly
50 - Approx
DETAIL H
SCALE 1 : 8
5
10
DETAIL G
SCALE 1 : 6
1
11
2
I
J
6
6
DETAIL I
SCALE 1 : 4
The Chain Swing & Ring
Trapeze Require The Supplied
Screw Caribiners To Be
Attached To The
Pre-Installed Caribiners.
DETAIL J
SCALE 1 : 4
Swings With Ropes Are
Adjusted Via The 'S' Hook
As Pictured. Chain Swings
Are Adjusted By Installing
The Screw Caribiner To
A Lower Chain Link.
Instruction:
Clip Swings Into Pre-Installed
Caribiners Hanging From
Swing Beam. Adjust As Necessary.
(Depending On What Was Ordered,
Swings May Differ From Those Shown).
STEP 6:
Installing Swings
SHEET 3 OF 3 Version: