Plextor 8PL-2 User manual

Hardware Installation
By itself, your CD-ROM drive is incapable of communicating with your computer.
You must use a hardware link that enables your drive to ‘‘talk’’ with the rest of your
computer.
Plextor’s8PleXdrivesuseaSCSIinterfaceastheirlink.IfyouownaPC,therearefour
ways in which you can make the SCSI connection:
1) Use a separate SCSI interface board. This is the most common method for
both internal and external drives. We recommend using a 32-bit PCI bus
masteringSCSIinterfaceboardtomaximizethedrive’spotential.Older8-bit
SCSI interface boards are not recommended. More cost-effective, but with
adecreaseinvideoperformance,are16-bitISAbusmasteringSCSIinterface
boards. Both these bus mastering interface technologies also allow you to
take advantage of SCSI multi-tasking in 32-bit operating systems such as
Windows 95, Windows NT, UNIX, SCO, Solaris, etc. Another possibility is
to use an ISA-PIO SCSI interface board, but performance will suffer, as will
multi-tasking.
2) Use a soundboard that also has a SCSI interface built onto it. This helps save
a slot in your computer by combining the functions of two boards (SCSI
interface board and soundboard) into one. Caution: Many older sound-
boards use only an 8-bit SCSI chip. If you need the performance a 16-bit
SCSI interface board provides (see page 32), you’ll have to buy a separate
SCSI board or a soundboard with a 16-bit SCSI interface built into it.
3) If you have an external drive, you can also use a parallel-to-SCSI interface.
Thisisadevicethatplugsintotheparallelport(theoneyourprinternormally
is connected to) of your computer. It is convenient, but typically at a cost of
reduced performance to your CD-ROM drive.
4) If you have an external drive and a portable computer with a PCMCIA slot
(Type II or III), use a PCMCIA-to-SCSI card. This is a small, credit-card size
devicethatplugsintothePCMCIAslot.Ittooisconvenient,butalsoprovides
lessperformancethanadirectconnectiontoa32-bitor16-bitSCSIinterface
board. PCMCIA connections should, however, provide better performance
than a parallel-to-SCSI interface.
---- CHAPTER 8 ----
20 PX-83CS/PX-85CS OPERATION MANUAL

NOTE: The following section is only for PC users who need to install a SCSI
interface board, or a soundboard with a built-in SCSI interface, in their
computer. If you plan to use a parallel-to-SCSI, or PCMCIA-to-SCSI
interface,you canskipto Chapter9. Ifyouare aMacuser, youcan laugh
at how easy life is and skip to page 29.
Board Installation
YOUR TASK: Install a SCSI interface board, or a soundboard with
a built-in SCSI interface, in your computer.
YOUR OBJECTIVE: Provide the hardware link needed to enable your
CD-ROM drive to communicate with your
computer.
YOUR METHOD: Remove your computer’s case. Install board and
attach necessary cables.
Let us point out that this is a CD-ROM drive installation and operation manual----it is
not a SCSI interface board or soundboard installation and operation manual. Unless
you purchased a SCSI interface board or soundboard (and its accompanying manual)
bundled in the same box with an 8PleX drive, we have no way of knowing which type
of board you elect to use. There are dozens of SCSI interface boards and soundboards
on the market. Each one is installed somewhat differently. Therefore, our instructions
for this section should only be considered as guidelines. For more detailed instructions
on how to properly install your SCSI interface board/soundboard, you should refer to
the installation/operation manual that you received when you purchased the board.
Caution: If static electricity may be present in the room where you are working,
dischargeanyyoumayhaveonyourbodybytouchingagroundedobject
before you remove the host adapter from its packaging.
Static electricity is a silent killer. Just a small jolt to one of the chips on
your interface board may render it useless with no apparent damage
visible. Positioning your computer in a location without a carpet under-
foot is one method of guarding against static electricity damage. Using
common sense, such as not walking on a carpeted floor in stocking feet
just before you install your drive, is another.
Before proceeding, make sure the power to your computer and any
external peripherals is OFF and your computer is UNPLUGGED from its
power source.
PX-83CS/PX-85CS OPERATION MANUAL 21

Toremoveyourcomputer’scover,followthedirectionsprovidedbyyourcomputer’s
manufacturer. Typically this involves loosening or removing several screws on the
back panel of your computer and sliding off your computer’s cover.
Carefully remove the SCSI interface board from its packaging. Select a vacant slot in
your computer where you will install the board (refer to the manual packaged with
your interface board for instructions as to which slot in your system to use). Plextor
providesboth16-bitISAand32-bitPCISCSIinterfaceboardswithitsoptionalbundles,
soyoumustusethecorrectslot(16-bitslotsarelongerthan32-bitslots).Oldersystems
maynothaveaPCIslot,as thisis thenewertechnology.Ifyouinstallaninternaldrive,
try to pick a slot that is closest to where the drive will be installed.
Remove the cover plate for this slot from the back panel of your computer. Keep the
screw from the cover plate nearby as you will need it in a moment. Save the cover
plate in case you need it at a later date.
Plug the SCSI interface board into the slot you have selected. Rock the board from
end-to-end to ensure that it seats firmly in the slot. Don’t force it. If you cannot push
the board down completely into the slot, remove the board and try again.
Expansion Slot Cover
Rear Panel
CHAPTER 8 ---- Hardware Installation
22 PX-83CS/PX-85CS OPERATION MANUAL

Onceyouhavesuccessfullyinsertedtheboard,fastenitinplaceusingthecoverplate
screw that you removed earlier.
PCI Board
ISA Board
CHAPTER 8 ---- Hardware Installation
PX-83CS/PX-85CS OPERATION MANUAL 23

Drive Positioning
YOUR TASK: Determine where you want to install your drive.
YOUR OBJECTIVE: Position the drive in the proper manner so that it
operates correctly.
YOUR METHOD: If you have an internal drive, find an open bay in
your computer. If you have an external drive, find
an open space on your desktop.
The PX-83CS and PX-85CS may be installed either horizontally or vertically. If
installed vertically, make sure that the eject button is positioned near the top of the
drive.
PX-83CS
PX-85CS
Vertical Horizontal
CHAPTER 8 ---- Hardware Installation
Vertical Horizontal
Eject Button UP
Eject Button UP
24 PX-83CS/PX-85CS OPERATION MANUAL

NOTE: The following section is only for those installing internal drives. If you
have an external drive, skip to page 29.
Mounting an Internal Drive
YOUR TASK: Mount your internal drive inside your computer.
YOUR OBJECTIVE: A securely positioned drive whose connectors are
within easy reach of the various cables that must
attach to it.
YOUR METHOD: Identify the drive bay where you will mount your
drive. Remove bay cover. If necessary, use
mounting rails to install drive in bay.
Your PC probably looks something like this:
You can mount your drive in any available bay. You must remove the small panel that
covers the bay that you want to use. Typically, this is done after you have removed
your computer’s cover. The panel can then be popped out by pressing outward lightly
(in some older cases you may have to remove screws that hold the panel in place).
You now need to determine if you must install mounting rails on the sides of your
drive. To do so, insert the drive into the open bay. If the drive fits tightly with little (or
no) clearance on either side of the drive, you will not have to use mounting rails. The
drive can be mounted directly into your computer.
Caution: Donotmount your driveinyour computer usingscrewsother than those
supplied by Plextor. You may damage the drive if you insert screws that
aretoolong.Ifyoufindthatyouarehavingdifficultyinsertingorejecting
a caddy from your drive, the cause may be that you are using screws
other than those supplied by Plextor. Another possibility is that you are
using Plextor’s screws, but you have tightened them too much. Try
backing the screws out a few turns and see if this corrects the problem.
!!
Available bay with
cover panel removed.
CHAPTER 8 ---- Hardware Installation
PX-83CS/PX-85CS OPERATION MANUAL 25

If you must use mounting rails, install them as shown below:
There are four holes provided on each side of the drive. To mount an internal drive
in most computers, the rails should be fastened to the lower pair of holes. In some
instances you may need to fasten the rails to the upper set of holes.
You will find that eight screws were supplied with your drive: four chrome screws
and four black screws. Select which screws to use based on which set of holes you
use to attach the mounting rails.
✓Use the chrome screws if you use the upper set of mounting
holes.
✓Use the black screws if you use the lower set of mounting holes.
Check the positioning of the rails by sliding the drive into the bay before you connect
any cables.
Check Your Jumper Settings
Once you have determined a) the correct set of holes to use to attach mounting rails,
or b) that you don’t have to use mounting rails, you are almost ready to finish your
drive’s installation. Before doing so, however, check your jumper settings one last
time.
If you do not have any SCSI peripherals (e.g., hard disk, scanner, printer, etc.) in your
systemotherthan your CD-ROMdrive,you should notchangethejumpers from their
factory setting.
If you do have other SCSI peripherals as part of your computer system, you may need
to change the settings of the SCSI ID and Terminator. See Chapters 6 and 7 for
information on how to change these settings.
Be sure not to mistake the inner and outer face of
the rail when attaching. The smooth side of the rail
faces away from the drive’s chassis.
CHAPTER 8 ---- Hardware Installation
26 PX-83CS/PX-85CS OPERATION MANUAL

Cable Connections
You must make a minimum of two cable connections to your CD-ROM drive. A third
cableconnection needbe madeonly ifyouareusingasoundboardinyourcomputer.
The two cable connections that you must make are:
1) SCSI cable
2) power cable
The SCSI cable you will need is included with your drive. It is a standard 50-pin flat
ribbon cable with three connectors (one at each end and one in the middle). If you
areconnectingthehostadaptertoyourPlextordriveonly,usethetwoendconnectors
and ignore the one in the middle. If you already have one other SCSI peripheral (such
as a hard disk), and your existing cable has only two connectors, remove the cable
and replace it with the cable provided by Plextor. Connect the SCSI host adapter to a
connection on either end of the cable. Connect the two peripherals to the other two
connectors (one at the middle connector and one at the end of the cable). Refer to
Chapter 7 of this manual for setting the termination of the devices.
If you have more than one other internal SCSI peripheral (besides your Plextor drive),
you will need to acquire a SCSI ribbon cable with more connectors (one connector for
each internal SCSI device plus an additional connector for the host adapter----refer to
Chapter 3). Refer to Chapter 7 of this manual for setting the termination of the devices.
CAUTION: It is easy to accidentally plug your SCSI ribbon cable upside down into
bothyourdriveandSCSIinterfaceboard.Accordingly,besureyoumatch
the red stripe along one side of the SCSI cable to pin 1 on the interface
boardandpin1onthedrive(asshownonthenextpage).Eachconnector
on the ribbon cable has a ‘‘key’’ in the middle. This key should fit into a
slot in the middle of each connector of the interface board, your 8PleX
CD-ROM drive, and any other SCSI peripherals.
CHAPTER 8 ---- Hardware Installation
Power Supply
from Personal
Computer
DC Power Supply
DC+12V 0.6A
DC+5V 0.3A
SCSI Ribbon Cable
SCSI Host Adapter
Personal Computer
Pin 1
Jumpers
SCSI Interface Connector
Power
Connector
Audio Connector
PX-83CS/PX-85CS OPERATION MANUAL 27

Double-check your work; you must ensure the side of the SCSI cable with
the red stripe is matched to pin 1 on the interface board and on the drive.
The easiest way to install your SCSI cable is to plug it into the SCSI connector on the
rear panel of the drive before you insert the drive into your computer. Then you can
thread the cable through the front of the open bay you plan to use and back toward
the SCSI interface board. Connect the cable to your SCSI interface board and finish
mounting your drive in the proper position. The drive should slide smoothly into the
bay.Ifitdoesnot,checkforobstructionsinthebayandensurethesiderails(ifneeded)
are attached properly.
You now need to make the power connection. In most computers you will find
additional power connectors that are ready for your use. Check the cable running
from your power supply to your hard disk and see if it has extra connectors on it. If
so, you can plug one of these into the power connector found on the rear panel of the
CD-ROM drive.
Pin #1
CHAPTER 8 ---- Hardware Installation
#1 To Pin #1
Either end of the cable may be
connected to either the CD-ROM
drive or to the SCSI interface board
28 PX-83CS/PX-85CS OPERATION MANUAL

If you do not find any additional connectors available (either because they were not
supplied, or they are all in use), you will have to buy a ‘‘splitter’’ or a ‘‘Y-connector.’’
These can also be found at most computer stores. If you are in a hurry to get started,
you can probably unplug the power connector from your 5.25" floppy drive (if you
haveone)and plug itintoyour CD-ROM drive.Youwillbe able touseyour CD-ROM
drive until you have the opportunity to buy a ‘‘splitter’’ or ‘‘Y-connector.’’ (Of course,
you will lose the use of your 5.25" drive until you buy a splitter/Y-connector.)
If your computer has only a 3.5" floppy disk drive, you may find that you do not have
a power connector that is the correct size to plug into your CD-ROM drive. Once
again, you can turn to your local computer store for a splitter to solve this problem,
or you might find an adapter that converts the smaller sized power plug found on a
3.5" drive to the size required for your CD-ROM drive.
A third cable, an audio cable, must be used if there is a soundboard in your system.
This cable runs from the four pin audio output connector on the rear panel of your
drive to your soundboard. See page 33 for more information about audio cables.
Installation of your internal drive is now complete. Skip to page 32.
External Drive Installation
YOUR TASK: Connect cables from your external drive to your PC
or Mac. Check to see if switch, dial, and terminator
settings need to be adjusted.
YOUR OBJECTIVE: A well-functioning drive that does not conflict with
any other peripherals in your computer system.
YOUR METHOD: Follow directions below for making cable
connections. Review your current computer set-up
to see if the potential for conflicts exists. If so, make
necessary switch, dial, and/or terminator changes.
IfyouareinstallingasinglePX-85CS,andyouhavenootherSCSIperipheralsattached
to your system, you should leave the switches, dial, and terminator found on the rear
panel of your drive at their factory settings. If you do have additional SCSI peripherals
(e.g., scanner, printer) attached to your computer, you may need to change your
switch, dial, and terminator settings. See Chapters 6 and 7 for information on how to
change these settings.
If you are installing a single PX-85CS external drive, connect it as shown on the next
page:
CHAPTER 8 ---- Hardware Installation
PX-83CS/PX-85CS OPERATION MANUAL 29

Mac connection (rear view of a Mac)
SCSI Interface Board
SCSI Cable
Secure to controller
by pushing gently
until cable ‘‘snaps’’
into place.
Personal Computer
AC Power
Supply
PX-85CS Rear Panel
X
Y
SCSI Cable
Plugs into Y
Plugs into X
(above)
CHAPTER 8 ---- Hardware Installation
PC connection
30 PX-83CS/PX-85CS OPERATION MANUAL

If you are installing more than one PX-85CS external drive (or one PX-85CS and other
external SCSI peripherals), connect them as shown below:
Y
CHAPTER 8 ---- Hardware Installation
PC connection
Mac connection
(rear view of a Mac)
SCSI
Interface
Board
Personal Computer
Termination
DISABLED
SCSI Cable
Daisy
Chain Cable
50 pin Centronics
X
SCSI Cable
Plugs into Y
Plugs into X
(above)
Termination
DISABLED
Termination
ENABLED
PX-83CS/PX-85CS OPERATION MANUAL 31

NOTE: The following section is only for those installing a soundboard in their
PC. If you are not using a soundboard, skip to Chapter 9.
Soundboard Installation
YOUR TASK: Install a soundboard in your PC.
YOUR OBJECTIVE: Make sure that the soundboard works properly with
your CD-ROM drive.
YOUR METHOD: Follow the instructions for installation that came
with your soundboard. Follow the instructions
given below to connect the soundboard to your
CD-ROM drive.
From Plextor’s perspective, soundboards fall into one of three major categories:
1) Soundboards that have no CD-ROM drive interface (e.g., ATI Stereo F/X,
Logitech Sound Man 16, Turtle Beach Multi-Sound). Most soundboards fall
into this category.
2) Soundboards that have a proprietary or IDE CD-ROM drive interface built
onto the board (e.g., Creative Labs Sound Blaster, Orchid Sound Producer
Pro,WearnesTech Beethoven ADSP-16).Typically,the only drives thatcan
be attached are mediocre performers that sell for a low price.
3) Soundboards that have a SCSI CD-ROM drive interface built onto the board
(e.g., Media Vision Spectrum 16, Diamond SonicSound, Prometheus Aria
16SE). Any SCSI CD-ROM drive can be attached to this type of soundboard
and should work if the proper device drivers are used. However, the SCSI
interface will not be high performance.
If you own a soundboard that falls into category #1 or #2 and want to use it with your
8PleX drive, you must also buy a separate SCSI interface board (e.g., Future Domain
TMC-1610, Adaptec AHA-1515). You should follow the directions starting on page
21regardingtheinstallationofaSCSIinterfaceboard.Then,checkthediagramsgiven
on the following page to see how you should connect your audio cable.
Ifyouownasoundboardfromcategory#3,youprobablydonothavetobuyaseparate
SCSI interface board unless you want maximum performance. This is because most
soundboards with a built-in SCSI interface use only an 8-bit SCSI interface. (This is
true even if you buy a ‘‘16-bit’’ soundboard. The ‘‘16-bit’’ refers to the audio channel,
not necessarily the SCSI data channel. The soundboard may have only an 8-bit SCSI
interface on it.)
CHAPTER 8 ---- Hardware Installation
32 PX-83CS/PX-85CS OPERATION MANUAL

Whichever category your soundboard falls into, you will find that the best source of
information about installing the soundboard in your computer is your soundboard’s
manual. Once you have successfully installed your soundboard in your computer,
you can continue to the next section, which describes the different cable connections
that need to be made.
Audio Cables
We include two audio cables with your internal CD-ROM drive and one cable with
your external drive. One cable delivered with your internal drive is MPC compliant,
and the other has connectors designed for use with Sound Blaster sound cards. The
cable delivered with your external drive has two RCA type color coded connectors
at one end, which connect to your drive, and a single stereo mini-jack at the other
end, which plugs into the line-in receptacle on your soundboard (at the back of your
computer).
IfyoupurchasedaninternaldriveandyouhaveasoundcardotherthanSoundBlaster
that is not MPC compliant, you will have to purchase a different audio cable from a
computer supply store. We can help by recommending several vendors (see listing,
p. 63) who offer audio cables, and can get them to you quickly at a reasonable price.
Call our Technical Support Department directly at 800-886-3935.
Please see next page for diagrams illustrating the cable connections.
CHAPTER 8 ---- Hardware Installation
PX-83CS/PX-85CS OPERATION MANUAL 33

The following diagrams show where the SCSI cable and audio cable need to be
connected to your internal CD-ROM drive:
CHAPTER 8 ---- Hardware Installation
Soundboard without SCSI Interface
1Audio Connector
2Power Connector
3 SCSI Connector
Soundboard with SCSI Interface
1Audio Connector
2Power Connector
3 SCSI Connector
34 PX-83CS/PX-85CS OPERATION MANUAL

Software Installation
YOUR TASK: Install software onto your computer system to
enable the CD-ROM drive to operate optimally
within your specific operating system.
YOUR OBJECTIVE: Enable your CD-ROM drive to communicate with
the rest of your computer system.
YOUR METHOD: Identify your operating system and refer to the
section of this chapter, or the Plextor Manager
manual, that pertains to your operating system.
A device driver is a software program that allows your computer to interact with
yourCD-ROMdrive.If you do not use a device driver,oryouuseanoutdated version
of the required device driver, you will not be able to operate your CD-ROM drive.
The lack of a device driver, or the use of an improper version of a device driver, are
the most common causes of calls to Plextor’s Technical Support Department.
•For PC users with Windows 95: please see the separate Plextor
Manager manual.
•For PC users with DOS/Windows: please see the separate Plextor
Manager manual.
•For Apple computer users: please see page 36.
•For PC users with IBM OS/2: please see page 37.
•For PC users with Windows NT: please see page 38.
---- CHAPTER 9 ----
PX-83CS/PX-85CS OPERATION MANUAL 35

FWB Toolkit for Macintosh
Device Driver Installation
The FWB Toolkit provided in your 8PleX MAC kit runs under System 6.08 and 7. In
addition to other formats, it supports Photo-CD (Multisession), Audio Extraction,
CD+G, CD Plus, and Enhanced CD.
1) To begin installation, insert the FWB floppy disk you received with your
CD-ROMdrive into yourdiskdrive. Makesurethat powertoyour CD-ROM
drive is OFF.
2) Drag each icon from the driver window into your SYSTEM FOLDER or use
the Installation program if one is available on the floppy.
3) Select‘‘ShutDown’’or‘‘Restart’’fromyourMacdesktop.Afterrestartingyour
Mac you should see the CD-ROM device driver as the Mac boots up. If the
icon appears crossed out, check to see that the CD-ROM drive power is on
and that the SCSI ID does not conflict with another device. Otherwise, wait
until the Mac is done booting up before inserting a disc.
SYSTEM 7 USERS: At this point a dialog box will appear telling you that these files
need to be stored in special places in the SYSTEM FOLDER. Click on OK and all the
files will be copied to their appropriate places.
4) Insert a caddy containing a CD-ROM disc (written in Mac format) into your
8PleX drive.
5) Your Mac will display the CD-ROM disc’s icon.
6) Double-click on the icon to start the program.
CHAPTER 9 ---- Software Installation
36 PX-83CS/PX-85CS OPERATION MANUAL

OS/2
Installation Procedure
To install OS/2 from your OS/2 CD-ROM disc, you first need to verify that your SCSI
interface board is supported by OS/2. Check your OS/2 manual and the README file
onthefloppydiskthatcomeswiththeOS/2CD-ROM,forinformationonwhichSCSI
interface boards OS/2 supports.
If your SCSI interface board is on OS/2’s list of supported hardware, you can follow
the installation instructions provided by IBM.
However, if your SCSI interface board is not on OS/2’s list of supported hardware,
youmustcontactthemanufacturerofyourboardandrequestanOS/2softwaredevice
driver. (See listing of key contact phone/fax/BBS numbers on page 63.)
The OS/2 device driver files that you need from your SCSI interface board’s manufac-
turer end with an ‘‘.ADD’’ extension. They need to be copied into the CONFIG.SYS
file on the OS/2 installation floppy disk. Your SCSI interface board manufacturer will
provide you with specific instructions.
Adding CD-ROM Support After OS/2 Has Already Been Installed
1) You first need to verify that your SCSI interface board is supported by OS/2.
Check your OS/2 manual, and the README file on the floppy disk that
comes with the OS/2 CD-ROM, for information on which SCSI interface
boards OS/2 supports. If your SCSI interface board is included on the list of
supported hardware, you can skip to step #3.
2) If your SCSI interface board is not on OS/2’s list of supported hardware, you
must contact the manufacturer of your board and request an OS/2 software
device driver. (See listing of contact phone/fax/BBS numbers on page 63.)
3) Once you have confirmed that your SCSI interface board is supported by
OS/2, or you have obtained the necessary device driver files, run OS/2’s
Selective Install program to set up your SCSI interface board and CD-ROM
drive. In the ‘‘SCSI Host’’ field, select your board. (If your board was already
installedand running,your SCSIinterfaceboardshouldalready beselected,
and there is no need for you to change this entry.) In the ‘‘CD-ROM Drive’’
field, select ‘‘Texel/Plextor 3024/5024, 3028/5028, 4PleX.’’ Then, select
‘‘Install’’ and insert the OS/2 floppy disks when requested. After rebooting,
your CD-ROM drive should appear in the ‘‘Drives’’ folder.
CHAPTER 9 ---- Software Installation
PX-83CS/PX-85CS OPERATION MANUAL 37

OS/2 Troubleshooting Tip
IfyouhavedifficultygettingOS/2torecognizeyourCD-ROMdriveandSCSIinterface
board, you should first verify that all of your hardware is operating properly.
This is best done by installing DOS. If your system also does not work under DOS,
you probably have a hardware problem that needs to be resolved before you can go
any further. Refer to the Troubleshooting guide in Chapter 12. If your system works
under DOS, but not OS/2, review your device driver installation and verify that the
SCSI interface board driver and CD-ROM support (see step #3 on page 37) is loaded
correctly.
Windows NT 3.51 (and Below)
Installation Procedure
To install Windows NT from your NT CD-ROM disc, you first need to verify that your
SCSI interface board is supported by NT. Check your NT manual for information on
which SCSI interface boards NT supports.
If your SCSI interface board is on NT’s list of supported hardware, you can follow the
installation instructions provided by Microsoft.
If your SCSI interface board is not on NT’s list of supported hardware, however, you
must contact your board’s manufacturer and request an NT software device driver
(see listing of key contact phone/fax/BBS numbers on page 63).
The files you obtain need to be added to the NT installation floppy disk(s) that came
with your NT CD-ROM disc. Your SCSI interface board manufacturer will provide
you with specific installation instructions.
Adding CD-ROM Support After NT Has Already Been Installed
1) You first need to verify that your SCSI interface board is supported by NT.
Check your NT manual for information on which SCSI interface boards NT
supports. If your SCSI interface board is included on the list of supported
hardware, skip to #3.
CHAPTER 9 ---- Software Installation
38 PX-83CS/PX-85CS OPERATION MANUAL

2) If your SCSI interface board is not on NT’s list of supported hardware, you
must contact your board’s manufacturer and request an NT software device
driver (see listing of key contact phone/fax/BBS numbers on page 63).
3) RunNT’sSetup program to addsupportfor your SCSI interfaceboard.Select
‘‘Add/Remove SCSI Adapters . . .’’ from the menu. Choose your SCSI inter-
face board from the list or, alternately, add the driver you obtained from
your SCSI interface board manufacturer.
4) Run the NT Control Panel and then run Devices. From the list of devices,
locate ‘‘Scsicdrom’’ and check the ‘‘startable’’ box. This procedure is fully
outlined in the Windows NT manual.
5) Reboot. Your 8PleX drive should now be visible to the system.
Windows NT Troubleshooting Tip
If you have difficulty getting NT to recognize your CD-ROM drive and SCSI interface
board, you should first verify that all of your hardware is operating properly.
This is best done by installing DOS. If your system also does not work under DOS,
you probably have a hardware problem that needs to be resolved before you can go
any further. If your system works under DOS, but not NT, review your device driver
installation and verify that the SCSI interface board device driver and CD-ROM
support (step #4, above) are loaded correctly.
CHAPTER 9 ---- Software Installation
PX-83CS/PX-85CS OPERATION MANUAL 39