portal Kanaloa User manual

(INFLATABLE SUP)
www.portaloutdoors.com

10‘6“*33”*6“ / 320X84X15cm
11‘6“*32”*6“ / 350X81X15cm
Kanaloa
Divine Sun
Māui
Costal
Māui
Safari

CONTENTS
Thank You for Choosing Portal Outdoor! - PLEASE READ CAREFULLY
Paddle sports can be a dangerous and physically demanding activity. Users of this product should
understandthat participating instand-up paddling can result inserious injury ordeath.
Observe all applicable watercraft laws, and use common sense.
We recommend that you inflate your inflatable stand-up paddle (inflatable SUP) board between
13 and 15 PSI. Under inflating the SUP can cause stability issues along with your SUP folding
during use.
As you approachthe weight limit, you should inflate the SUP closerto the upper PSI limit.
Paddle boards can hold max 300 pounds.
• Check your board and equipment before going inthe water.
• Always paddle with others.
• Always wear aleash attaching you tothe board.
• Wear a Coast Guard approved personal flotation device.
• Always wear protective clothing.
• Always paddle insafe conditions.
• Be aware of changing weatherconditions.
• Do not exceed your paddling ability; be aware of your limitations.
• Do not use alcohol or mind altering drugs priorto or while using this product.
• To keep the board in the best possible condition, it is recommended that you always deflate then
fold up the board and put it inthe protective bag when it is not in use.
• Find a balanced stance with both feet positioned roughly shoulder width apart. Your knees should be
slightly bent with your upper body in a relaxed, upright position. Keep your shoulders back and look
straight ahead.
• To properly grip the paddle, place one hand on top of the paddle. Raise the paddle over your head
and position your other hand so that both elbows are at 90 degree angles. The paddle blade should
be pointed forward when paddling. Paddle in smooth, front to back motion. Avoid leaning to the side
when paddling.
The paddle is adjustable. You may needtomake the paddle longer for comfortable paddling.
• To turn left, grip the top of the paddle with your left hand and concentrate on paddling on the right
side of the board.
• To turn right, grip the top of the paddle with your right hand and concentrate on paddling on the left
side of the board.
Safety Check List
How to Use
WARNING
GENERAL PADDLING INFORMATION
General Information··························································
Inflating Yo u r Boa r d ·························································
Board Leak Detection and Repair·····························
Board Care and Storage··················································
Folding Your Board ··································································
3
6
9
10
10

PORTAL Inflatable SUP PARTS LIST
Please Check All Parts Are Present In Your Package Before First Use
E GF
JIH
ITEMS INCLUDED
A
B
C
D
E
F
G
H
I
J
1
1
1
1
1
1
1
1
1
1
Inflatable Stand-Up Paddle Board
Detachable Fin
Paddle Safety Leash
Carry Backpack
Paddle Fin
Aluminum Paddle Body w/ Adjustable Clasp
Adjustable Aluminum Paddle Grip
Hand Pump w/ Gauge
Repair Kit
Phone waterproof bag
A CB D

BOARD STRUCTURE
INFLATABLE SUP FEATURES
I
II
III
IV
V
VI
VII
VIII
3
6
1
1
1
5
2
1
Heavy duty webbing handle
Bungee Cord D-Rings
Bungee Storage Cord
Non-Slip EVA Foam Deck Board
High Pressure Inflation Valve
Paddle Safety Leash D-Ring
Fixed Stabilizing Fins
Removable Tracking Fin
I
I
I
II
IV
V
VII
VI
VI
VIII
III

GETTING READY - INFLATING PORTAL Inflatable SUP
1.Unpack Your Inflatable SUP Set
2.Unlock Valve for Inflation
3.Pose
4.Secure air pressure
Choose a smooth and clean surface to unfold board. Roll out the inflatable SUP
board completely flat with the Non-Slip EVA Foam Deck side facing up.
Find the high pressure inflation valve near the bottom of the board. Twist the cap
counter clockwise to detach and access the center valve pin. Press the center pin
once to pop it up slightly. Now the valve is in "open" position for inflating . Be careful
of any sand or debris around the valve area when inflating and deflating, as small
particles could become airborne with the release of air.
Always keep the center pin in "close" position and screw the cap clockwise to block
air outflow when in use. This will prevent accidental air release and entrance of any
particles into the air chambers.
Connect pump and start inflating.
When PSI monitor reaches a desired level, please detach the hose from the valve.
Press the center valve pin down to "close" position and screw the cap clockwise to
secure are pressure.

5.Attach Tracking Fin
The board can be inflated either with our hand pump or an electric pump.
The electric pump can inflate the board to a moderate pressure and save a lot
of time with about 90% of the required air volume. You will need to use your
hand pump to inflate the chambers to the correct pressure.
In addition to the two side fins that are fixed to the board, there is also a removable
tracking fin that needs to be attached. This fin helps with "tracking" or keeping the
SUP moving in a straight direction. Once the board is inflated, flip over the board
facing down to attach the tracking fin.
Put fin base into fin box from the wide inlet. Push the fin down. The fin base will
slide to the end of box at the same time. Turn the screw to secure fin firmly.
Make sure the center fin box is clean and free of debris.
INFLATION TIPS AND PRECAUTIONS
Do not use an air compressor. Damage to your board caused by over inflation
from an air compressor is not covered by your warranty.
After 2 or 3 days there may be a small decrease of pressure due to
temperature change. If so, add a few pumps of air.
Before undertaking a long paddle, inflate the board for a full 24 hours to
be sure the board is airtight. If you are seeing a consistent decrease in air
pressure, follow the instructions for leak detection in the board repair section
of this manual.

6.Assemble Aluminum Adjustable Paddle
7.Paddle Safety Leash
8.Deflate Without a Manual Pump
To assemble the paddle, hold the button in while sliding the pieces together until they
click into place. The last section (top) ofthe paddle is adjustable.
To find the ideal height for your paddle, start by building the paddle so it is 6 inches
taller than your own height. From this point, adjust the top section up or down until
the length is comfortable for you. A longerpaddle is bettersuited for a smooth, easier
paddling motion. A shorterpaddle is good for performance or competition riding.
Then attach the other end of the safety leash to the safety D-ring by pulling the
inner rope through the ring and secure in place with the Velcro tape.
When packing your inflatable SUP, remove all detachable parts. Then lay the board
facing up on a smooth surface. Clean any unwanted debris, especially around the
valve area. Open the valve cap and press the center pin to start releasing air.
There will be an initial burst of air, but will turn to slow release. When the air
outflow slows down, start rolling up the board from the opposite end and fold it
into a packing size. When packing, lock the valve cap to protect the center pin and
elongate inflatable SUP lifetime.

9.Deflate With a Manual Pump
1.About PVC
2.Air Leak Detection
3.Small Repairs
Remember to step on the pump securely, to prevent slipping.
Your new stand up paddleboard is made from a durable PVC. If a tear or puncture
does occur, PVC is very easy to repair. Repairs are easily done with your included
patch kit.
Read the following paragraphs for leak detection and repair tips.
If the board is losing air pressure not caused by colder temperature, then check for
leaks. Start with the valve.
Punctures less than 1/8" in size can be repaired simply without a patch. Deflate your
board, then clean and dry the area to be repaired. Apply a small drop of glue to
cover the puncture, and let it dry 12 hours.
BOARD LEAK DETECTION AND REPAIR
A leaking valve is rare, but if you did find one, please contacts us via
[email protected]. Your paddleboard comes with 1 year quality warranty.
If you continue to have problems it's probably time to order a replacement valve kit
or a new model. Replacement of the whole valve can be done with a simple tool that
comes with the replacement valve kit.
If your board needs repair, use the patches in the repair kit and follow these steps:
Deflate the board completely, lay it flat and wait for it to dry.
Cut a patch that is 2 inches larger than the tear/rip all the way around.
Use alcohol to clean the repair area.
Apply three coats of adhesive to the patch and the board. Wait 5 minutes inbetween
each coat.
Place the patch over the tear/rip. The adhesive will react quickly, so make sure the
positioning is precise/accurate. Use the roller to ensure the patch lays flat and even.
Wait 24 hours before re-inflating the board.

way to repair it.
To ensure your inflatable SUP would stay in the game longer
The board storage bag is designed to allow you to get your board into the bag as
easily as possible with minimal folds. Do not roll up the board too tight when storing
it while deflated.
• Before storing, hose o the board and let it dry completely to prevent mildew
buildup.
• Do not use harsh chemicals for cleaning. Most dirt can be removed with a mild soap
and fresh water.
• To keep the board in the best possible condition, it is recommended that you always
deflate then fold up the board and put it in the protective bag when it is not in use.
prevent exposure to the elements.
• Hanging the board is not recommended.
• Do not store in extreme conditions (i.e. above 150F or below -10F)
• Store in a clean, dry, sheltered place.
BOARD CARE AND STORAGE
BOARD FOLDING STEPS
Follow the diagram below for the best folding procedures.
Step 1：
Step 2：
Step 3：

To register your online purchase, please send a screenshot of your order details to
our after sales team: [email protected].
To thank you in addition to activate the 180-day extended quality warranty.
Information are collected for warranty service and product R&D only.
Thank you for shopping with www.portaloutdoors.com.
[email protected]
PORTAL STAND UP PADDLEBOARD REGISTRATION CARD
@PortalOutdoorsGear
@portaloutdoorsgear