PQS PN 80104-MICROS User manual

Ceiling Mount with a 7 Axis Extendable Arm and a 75-100mm VESA Screen Pan and Tilt Head
PN 80104-MICROS, PN 80104-20-MICROS, PN 80104-26-MICROS 1
[e-mail] WWW.PRACTICALQUALITYSYSTEMS.COM [phone]
ALL PRODUCTS PATENT PENDING
PN 80104-MICROS
PN 80104-20-MICROS
PN 80104-26-MICROS

Ceiling Mount with a 7 Axis Extendable Arm and a 75-100mm VESA Screen Pan and Tilt Head
PN 80104-MICROS, PN 80104-20-MICROS, PN 80104-26-MICROS 2
[e-mail] WWW.PRACTICALQUALITYSYSTEMS.COM [phone]
ALL PRODUCTS PATENT PENDING
Note - PN 80104-MICROS shown above; however the basic mechanics of PN 80104-20-MICROS and
PN 80104-26-MICROS are the same; only the lower arm sections are longer.
General Features
•These articulating ceiling mounts support MICROS terminals with the MICROS Quick Connect tabs and
slots mounting standard for Point of Sale / POS, Kitchen Display Systems / KDS in commercial
kitchens, retail, restaurants, offices, industry, shops, medical, maritime, schools, laboratory and many
other applications.
•An innovative set of joint assemblies allow seven axis of position adjustment when attached to a Ceiling
shelf or other flat, horizontal surface. This assembly is also available in wall and countertop mount
configurations.
•Beyond having very flexible articulation; this mount has the key feature of being easily LOCKED in any
desired screen position; this ability is VERY important when using touch screen equipment as it
PREVENTS the screen from moving away from the user each time a touch is input.
•This assembly supports up to 25 lbs., is made from steel and finished with a durable, black, low gloss,
micro wrinkle powder coat that resists fingerprints.
•Visit kitchendisplaysystems.com for a free, easy to understand tutorial that covers all aspects of
Kitchen Display Systems knowledge!
•For more information on the individual components included in this package please refer to the
assembly sketches in this document and the downloadable product information sheets available on
our website for each of the product pages for each part number.

Ceiling Mount with a 7 Axis Extendable Arm and a 75-100mm VESA Screen Pan and Tilt Head
PN 80104-MICROS, PN 80104-20-MICROS, PN 80104-26-MICROS 3
[e-mail] WWW.PRACTICALQUALITYSYSTEMS.COM [phone]
ALL PRODUCTS PATENT PENDING
Enhanced MICROS compatible Pan and Tilt Head with side-to-side tilt adjustment on an Offset Arm
Bracket
•A universal mount that works with any MICROS compatible terminal with then tabs and slots standard.
•Tightening the 2 four-point knobs applies variable clutching resistance to allow adjustment of the up
and down tilt position of the terminal. Tighten either of the two 10-32 Phillips head screws adjacent to
the four-point knobs to permanently secure the tilt position.
•Tightening the five- point knob below the Offset bracket applies variable clutching resistance to allow
adjustment of the side-to-side pan position of the terminal. A 10-32 Phillips head screw in the center of
the lower Panning plate can be tightened to permanently secure the pan position.
•Tightening the three - point knob at the rear center of the MICROS compatible mounting plate applies
variable resistance to allow adjustment of the side-to-side terminal tilt position.
•Tighten the 10-32 Phillips head screw on the lower Panning plate into one of the holes in the Offset
bracket to permanently secure the pan position.
•The Offset Bracket attaches the MICROS compatible pan and tilt head to the end of the arm and allows
adjustment of the up and down “Offset angle” of the arm.
•Adjusting the Up and down position of the arm at the Offset bracket: Remove the 1/4” Wire-Lock Clevis
Pin from the Offset Bracket to adjust the up and down position of the arm; then reinsert the pin into one
of the holes in the Offset bracket and through the arm to secure the new position.
MICROS quick connect
tabs and slots adapter
plate is attached here

Ceiling Mount with a 7 Axis Extendable Arm and a 75-100mm VESA Screen Pan and Tilt Head
PN 80104-MICROS, PN 80104-20-MICROS, PN 80104-26-MICROS 4
[e-mail] WWW.PRACTICALQUALITYSYSTEMS.COM [phone]
ALL PRODUCTS PATENT PENDING
Telescopic Arm Section
The overall length of the Telescopic arm section can be adjusted up to 6 inches. To adjust; grasp the inner arm
and slightly loosen the three-point knob just until the inner arm can be moved. Pull the inner arm out to extend
it or push it in to retract the arm to the desired new length; then retighten the knob to secure the position.
Below is a partial list of Oracle MICROS compatible Terminals that use the MICROS Quick Connect
tabs and slots mounting standard:
Oracle MICROS Workstation 625X.
Oracle MICROS Workstation 655X.
Oracle MICROS Workstation 6 POS Terminal.
Oracle MICROS Workstation 610.
Oracle MICROS Workstation 620.
Oracle MICROS Workstation 625.
Oracle MICROS Workstation 650.
Oracle MICROS Workstation 625.
Oracle MICROS Workstation 655.
Oracle MICROS Compact Workstation 310.
Oracle MICROS Express Station 4 Series.
Oracle MICROS Express Station 400.
Oracle MICROS Express Station 410.

Ceiling Mount with a 7 Axis Extendable Arm and a 75-100mm VESA Screen Pan and Tilt Head
PN 80104-MICROS, PN 80104-20-MICROS, PN 80104-26-MICROS 5
[e-mail] WWW.PRACTICALQUALITYSYSTEMS.COM [phone]
ALL PRODUCTS PATENT PENDING
Panning Ceiling Mounting Plate, Offset Bracket and Arm
•The Panning Ceiling Mounting Plate supports one arm assembly and can be attached to any flat,
smooth horizontal surface.
•Attach the mounting plate to the mounting surface with appropriate fasteners.
•The side-to-side pan position resistance is preset at the factory with a 5/16” bolt in the center of the
upper standoff plate to allow the arm offset bracket to move freely side to side and should not need
adjustment. However, a ½” wrench can be used to adjust the tension on this bolt.
•To adjust the side-to-side pan position of the Offset Bracket and Arm; remove the 10-32 Thumbscrew
from the top of the Panning Ceiling Mounting Plate; adjust the arm position, then reinstall the
thumbscrew into one of the holes in the top of the round section on the mounting plate.
•The Offset Bracket attaches the arm to the Panning Ceiling Mounting Plate and allows adjustment of
the up and down “Offset angle” of the arm.
•Adjusting the Up and down position of the arm at the Offset bracket: Remove the 1/4” Wire-Lock Clevis
Pin from the Offset Bracket to adjust the up and down position of the arm; then reinsert the pin into one
of the holes in the Offset bracket and through the arm to secure the new position.
•Note; it is best to keep the Offset positions of both the upper and lower Offset brackets on an arm
assembly “matched” so that the Panning base of the MICROS compatible pan and tilt head remains
horizontal. Example; if the upper Offset bracket and the Mounting plate is set to place the arm in the 1st
position at an outward angle from the wall; then the position of the Lower Offset bracket should be set
to the 1st position in the opposing angle to match it and keep the Panning base of the MICROS
compatible pan and tilt head horizontal

Ceiling Mount with a 7 Axis Extendable Arm and a 75-100mm VESA Screen Pan and Tilt Head
PN 80104-MICROS, PN 80104-20-MICROS, PN 80104-26-MICROS 6
[e-mail] WWW.PRACTICALQUALITYSYSTEMS.COM [phone]
ALL PRODUCTS PATENT PENDING
Installation Tips - How to Attach the Oracle MICROS compatible Quick Disconnect Adapter Pan and Tilt
Head assembly to the back of a screen:
1. Lay the terminal face down on a flat, smooth surface.
2. Hold the Pan and Tilt Head with the MICROS compatible quick connect adapter assembly securely, remove
the five- point hand knob from the underside of the end of the arm, lift off the Pan and Tilt Head with the
MICROS quick connect adapter assembly, then remove the rubber clutch washer from the top of the end of the
arm.
3. Orient the flat bottom of the panning base of the Pan and Tilt Head with the MICROS quick connect adapter
assembly with the bottom of the terminal.
4. Set the Pan and Tilt Head with the MICROS quick connect adapter assembly with the plate facing down on
the back of the terminal.
5. Align the square pattern of four tabs on the adapter plate with the pattern slots on the undersides of the four
raised stand -offs on the back of the terminal; and then guide the two together until the tabs are fully inserted
into the slots.
6. Carefully tighten the RED headed M4 screw through the plate and into the stand - off on the back of the
terminal, then carefully test that the terminal is now securely locked to the adapter plate.
7. Place the rubber clutch washer on the top of the end of the arm.
8. Carefully lift the terminal with the attached Pan and Tilt Head with the MICROS quick connect adapter
assembly, align the tapped hole in the panning base with hole in the rubber clutch washer on the top of the end
of the arm, reinstall the shaft of the five-point hand knob up through the underside of the arm, through the
rubber clutch washer and then carefully thread it into the panning base.
MICROS STANDARD QUICK CONNECT
TABS AND SLOTS ADAPTER PLATE

Ceiling Mount with a 7 Axis Extendable Arm and a 75-100mm VESA Screen Pan and Tilt Head
PN 80104-MICROS, PN 80104-20-MICROS, PN 80104-26-MICROS 7
[e-mail] WWW.PRACTICALQUALITYSYSTEMS.COM [phone]
ALL PRODUCTS PATENT PENDING
MICROS STANDARD QUICK CONNECT
TABS AND SLOTS ADAPTER PLATE
MICROS STANDARD QUICK CONNECT
TABS AND SLOTS ADAPTER PLATE
Install the Oracle MICROS External Power Supply PN 400351-038-PT or other model on the power supply
holder and secure with the hook and loop straps.
Once the four taps on the adapter plate are properly inserted into the four slots on the back of the terminal;
tighten the red headed lock screw to secure the WS6 or other terminal to the adaptor plate.

Ceiling Mount with a 7 Axis Extendable Arm and a 75-100mm VESA Screen Pan and Tilt Head
PN 80104-MICROS, PN 80104-20-MICROS, PN 80104-26-MICROS 8
[e-mail] WWW.PRACTICALQUALITYSYSTEMS.COM [phone]
ALL PRODUCTS PATENT PENDING
There are three extension arm assembly sections available. Please specify when ordering.
Each assembly is shown with dimensions that reflect the fully retracted and fully extended positions.
PN 80104-MICROS with an 8 ½”L arm which allows the mount to extend from 14”L to19 1/2”L
PN 80104-20-MICROS with a 20”L arm which allows the mount to extend from 26”L to 31 ½” L
PN 80104-26-MICROS with a 26”L arm which allows the mount to extend from 32” to 37 ½” L
We believe in ethical SEO relevancy; the following section was included to assist the all-knowing
algorithms in locating this page; however, some humans like it too.
•MICROS Ceiling mount, MICROS Ceiling mounting bracket, MICROS Ceiling mount bracket, MICROS
Terminal Ceiling mount, MICROS Terminal Ceiling mounting bracket, MICROS Terminal Ceiling mount
bracket.
•MICROS Point of Sale terminal Ceiling mount, MICROS KDS Ceiling mount, MICROS KDS Ceiling
mounting bracket, MICROS KDS Ceiling mount bracket, MICROS Kitchen Display System Ceiling
mount.
PN 80104-MICROS
PN 80104-20-MICROS
PN 80104-26-MICROS

Ceiling Mount with a 7 Axis Extendable Arm and a 75-100mm VESA Screen Pan and Tilt Head
PN 80104-MICROS, PN 80104-20-MICROS, PN 80104-26-MICROS 9
[e-mail] WWW.PRACTICALQUALITYSYSTEMS.COM [phone]
ALL PRODUCTS PATENT PENDING
Installation Tips for Screen Mounting Systems
•1. 1 Installation of this assembly must be performed by qualifed persons.
•1.2 Use fasteners that are appropriate for the materials and structure of the mounting surface.
Tips for locating KDS or POS Screen Mounting Systems
•1.1 Care must be taken when locating KDS or POS Screens so that the display can be easily seen by
the users (and in some cases touched); and also so that the screen does NOT block access to the pass
through window or items such as ingredients, plates, microwaves, etc. that are located on the adjacent
shelves.
•1.2 As a general rule of thumb KDS and POS screens should be located to place the center of the
display at, or just above, eye level.
•1.3 Most KDS screens are supported by mounting systems that are attached directly to the edge of
existing kitchen shelves above a production work station or expo area. POS Screens are most often
attached to counter tops, Under counter, shelve edges or walls.
•1.4 Conduct a careful survey of each POS station, Kitchen work station or expo area. Stand where the
users will be standing at their work stations and consider all possible screen locations. Again ; the
screens should be located where they are readily accessible; but also where they do not limit access to
other important items in the work area.
PN 80104-MICROS
PN 80104-20-MICROS
PN 80104-26-MICROS

Ceiling Mount with a 7 Axis Extendable Arm and a 75-100mm VESA Screen Pan and Tilt Head
PN 80104-MICROS, PN 80104-20-MICROS, PN 80104-26-MICROS 10
[e-mail] WWW.PRACTICALQUALITYSYSTEMS.COM [phone]
ALL PRODUCTS PATENT PENDING
Locating a Screen or Printer mount and examining the range of Motion of the arm(s).
1.1 Cut a section of blue painter’s tape that is the same width as the mounting plate and keep this handy.
1.2 Carefully Lift the mounting system, and place the mounting plate in contact with the mounting surface at
the proposed mounting location; then consider if the location of the MICROS pan and tilt head or printer tray
are accessible; but also not creating any conflicts with other items in the work area. If the system has movable
arm(s) move these through their entire range of motion and look for conflicts. If conflicts are found; adjust the
proposed location of the mounting plate as needed. When the optimum location is discoved; apply the tape to
the spot on the mounting surface.
1.3 An alternate method that can be used as an aid in determining the best location for screens or printers is to
make a cardboard cut out that has been shaped to closely match the overall dimensions of the intended screen
or printer tray. (In a pinch you can also use a tray or a pizza box as a stand in for a screen.) Use these
cardboard models as stand in for the actual equipment to assist in demonstrating the best positions of screens
or printers.
3.4 If the screen or printer is supported by an arm; locate the pivot points of the arm and then carefully guide
the MICROS pan and tilt head or printer tray horizontally through the entire range of movement to determine
optimum location for the mounting plate. When this location is discovered; apply the tape to the spot on the
mounting surface.
PN 80104-MICROS

Ceiling Mount with a 7 Axis Extendable Arm and a 75-100mm VESA Screen Pan and Tilt Head
PN 80104-MICROS, PN 80104-20-MICROS, PN 80104-26-MICROS 11
[e-mail] WWW.PRACTICALQUALITYSYSTEMS.COM [phone]
ALL PRODUCTS PATENT PENDING
The three mounting systems below are available in wall mount configurations with similar seven axis
functionality.
PN 80005-MICROS Includes an 8.63” long lower arm that allows the mount to extend from 7” to 12”+
PN 80005-20-MICROS Includes a 20.63” long lower arm that allows the mount to extend from 19” to 24”
PN 80005-26-MICROS includes a 26.63” long lower arm that allows the mount to extend from 25” to 30”
Custom length lower arm assemblies are also available. Please contact our design team.
PN 80005-MICROS
PN 80005-20-MICROS
PN 80005-26-MICROS

Ceiling Mount with a 7 Axis Extendable Arm and a 75-100mm VESA Screen Pan and Tilt Head
PN 80104-MICROS, PN 80104-20-MICROS, PN 80104-26-MICROS 12
[e-mail] WWW.PRACTICALQUALITYSYSTEMS.COM [phone]
ALL PRODUCTS PATENT PENDING
PN 80000-MICROS
PN 80050-MICROS
PN 80053-MICROS
PN 80910-GAL-MICROS
PN 80942-MICROS
PN 80005-MICROS
PN 80005-3036 MICROS
PN 80005-3642 MICROS
The following pages feature other MICROS compatible mounts; more options are available on our website;
contact our applications team for custom solutions.

Ceiling Mount with a 7 Axis Extendable Arm and a 75-100mm VESA Screen Pan and Tilt Head
PN 80104-MICROS, PN 80104-20-MICROS, PN 80104-26-MICROS 13
[e-mail] WWW.PRACTICALQUALITYSYSTEMS.COM [phone]
ALL PRODUCTS PATENT PENDING
PN 80117-MICROS
PN 80117-MICROS
PN 80914-MICROS
PN 80273-MICROS
PN 90530-MICROS
PN 80270-MICROS

Ceiling Mount with a 7 Axis Extendable Arm and a 75-100mm VESA Screen Pan and Tilt Head
PN 80104-MICROS, PN 80104-20-MICROS, PN 80104-26-MICROS 14
[e-mail] WWW.PRACTICALQUALITYSYSTEMS.COM [phone]
ALL PRODUCTS PATENT PENDING
PN 80104-MICROS
PN 80104-20-MICROS
PN 80104-26-MICROS
PN 80941-MICROS
PN 80113-MICROS
PN 80112-MICROS
PN 80016-MICROS
PN 80017-MICROS

Ceiling Mount with a 7 Axis Extendable Arm and a 75-100mm VESA Screen Pan and Tilt Head
PN 80104-MICROS, PN 80104-20-MICROS, PN 80104-26-MICROS 15
[e-mail] WWW.PRACTICALQUALITYSYSTEMS.COM [phone]
ALL PRODUCTS PATENT PENDING
PN 80622-MICROS
PN 80620-MICROS
PN 80621-MICROS
PN 802009-MICROS
PN 80014-MICROS
PN 80247-MICROS
PN 80246-MICROS
PN 80248-MICROS
PN 80101-MICROS
PN 80100-MICROS
PN 80140-MICROS

Ceiling Mount with a 7 Axis Extendable Arm and a 75-100mm VESA Screen Pan and Tilt Head
PN 80104-MICROS, PN 80104-20-MICROS, PN 80104-26-MICROS 16
[e-mail] WWW.PRACTICALQUALITYSYSTEMS.COM [phone]
ALL PRODUCTS PATENT PENDING
PN 90530-MICROS
PN 90500-MICROS
PN 90520-MICROS
PN 80003-MICROS
PN 90510-MICROS
PN 90540-MICROS