manuals.online logo
Brands
  1. Home
  2. •
  3. Brands
  4. •
  5. Precision
  6. •
  7. Lawn Sweeper
  8. •
  9. Precision SW38PRE User manual

Precision SW38PRE User manual

SW38PRE - 38” Tow Behind Lawn Sweeper
Owner’s Manual and Parts List
Precision Products, Inc.
LIMITED WARRANTY
This unit is warranted against defects in materials and workmanship to the original
purchaser, under normal use and service, for a period of ninety (90) days from date
of sale. During the Warranty Period, we will repair or replace at our option free of
charge to the original purchaser, any part of the Unit that our examination shows to
be defective in workmanship or materials. This Warranty Does Not apply to damage
caused by misuse, abuse, neglect, accident, normal wear, or alterations by
unauthorized persons.
Customer Service & Warranty Information
PLEASE DO NOT RETURN THIS MERCHANDISE TO THE STORE. CALL US AND WE WILL TAKE CARE OF ANY
PROBLEM YOU MIGHT HAVE WITH THIS PRODUCT. Phone (800) 225 - 5891 EXT. #204
When ordering parts always give model
number, part description & part number.
Send To: Precision Products, Inc.
Parts Division Phone (217) 735-1590
316 Limit Street Fax (217) 735-2435
Lincoln, IL 62656
Parts list on back page
11/05
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
**
**
**
Stub Axle
Wheel Shield
Flange Bearing
1/4” x 1/2” Hex Head Bolt
3/8” Lock Nut
Pinion Pawl
Brush Axle / Disc Assembly
Pilot Spacer
3/8” Hex Head Nut
Brush Clamp
Brush Strip
Top Hamper Side Tube
Bottom Hamper Side Tube
Hamper Tie Rod
Hamper Pivot Bracket Assembly
1/4” x 1-1/4” Hex Head Bolt
Top Hamper Cross Tube
Fiberglass Hamper Support Rod
Bottom Hamper Cross Tube
Leg Stand
**PARTS NOT ILLUSTRATED
Hamper (Material)
Wind Apron
Hamper Dump Rope
Ref # Part Description Qty.
Part # Ref # Part Description Qty.
Part #
2
2
2
2
4
4
2
12
12
36
36
37
37
38
39
39
39 40
40
41
42
42
43
44
Top Frame Tube
1/4” Nylon Lock Nut
Side Frame Tube
1/4” x 1-3/8” Hex Head Bolt
LH Hamper Pivot Bracket
RH Hamper Pivot Bracket
Sweeper Chassis
Height Adjustment Tube
Handle Grip
Spring
5/16” x 1-3/4” Hex Head Bolt
5/16” Nylon Lock Nut
RH Hitch Arm Tube
LH Hitch Arm Tube
Bumper Assembly
Clevis Pin
5/16” x 2-3/4” Hex Head Bolt
Clevis Plate
Hitch Pin Clip
Plastic Hub Cap
5/8” E Type Snap Ring
10” Tire
10” Die Cast Wheel
Pinion Gear
3241
1778
1701
6129
1776
1774
1721
1745
1746
1282
2051
1749
1722
1723
1724
1840
1707
1753
1042
1769
1768
1766
1767
1765
1708
1709
1770
1647
1771
1772
3242
1710
1273
1739
3237
1726
1712
1730
1755
1660
1727
1728
1729
1734
3239
3240
1790
1
16
2
12
1
1
1
1
1
1
3
6
1
1
1
1
1
2
1
2
4
2
2
2
2
2
2
14
2
2
1
2
4
12
6
2
2
1
2
2
1
2
1
2
1
1
1
1
2
2
2
2
2
3
4
4
3
4
4
4
4
5
6
7
8
9
10
11
12
12
12
13
14
15
11
16
17
18
19
20
21
21
22
23
24
25
26
27
15
28 29
30
31
32
33
34
35
28
Parts List for SW38PRE
Your new SW38PRE lawn sweeper is precision manufactured using the finest in tools and materials. Although it is
ruggedly constructed, do not subject this unit to misuse. Be sure to wipe off your unit after each use. Store in a
dry place out of direct sunlight. Do not permit the lawn sweeper to stand in the hot sun, unless it is in actual use.
You will find many work saving uses for your lawn sweeper. Use it early in the spring to give your lawn a good healthy
scrubbing. Use it throughout spring and summer before and after mowing. Sweeping your lawn before mowing stands
the grass up for a clean, even cut. It also allows increased protection to your mower by removing sticks, stones and
nuts, which might damage the blade(s) on your mower. Sweeping your lawn after mowing will whisk away unsightly
grass clippings - leaving your lawn velvety smooth.
Tools Required For Assembly:
Parts List Of SW38PRE
One (1) - Pair Pliers (Needle Nose)
Two (2) - 7/16” Wrenches
Two (2) - 1/2” Wrenches
Prior To Assembly:
Remove all Sweeper Parts from carton. Make sure all parts and assemblies are
present before assembly. If any parts are missing, contact Customer Service
(contact information on back sheet) immediately for assistance.
Lay out all parts and have tools ready.
Assembly Parts List Description
A
B
CD
EF
GHIJ
Hamper Assembly
Chassis Assembly
Hamper Pivot Brackets
Clevis Plates
Bottom Hamper Cross Tube
Top Frame Tube
Wind Apron
Fiberglass Hamper Support Rods
A
B
C
D
E
F
G
H
1
1
2
2
1
1
1
2
Ref. Description Qty.
K
L
MN
O
P
Top Hamper Side Tubes
Bottom Hamper Side Tubes
Height Adjustment Tube
RH Hitch Arm Tube
Leg Stands
Side Frame Tubes
LH Hitch Arm Tube
Hardware Sack
I
J
K
L
M
N
O
P
2
2
1
1
2
2
1
1
Ref. Description Qty.
OPERATION:
Brush Adjustment: To raise the brushes further away
from the ground, push the Height Adjustment Tube
back and down until desired sweeping height is
attained. To lower, push the Height Adjustment Tube
back and pull up to desired sweeping height (See Fig 7).
For best results, brushes should barely touch the top
of the grass blades. Brushes should be raised when
transporting the unit to and from sweeping area.
Sweeping Speed: For best results, rider/tractor
should travel at a 3 to 5 M.P.H. range.
Dumping: Simply pull the Hamper Dump Rope
forward to empty debris (See Fig. 8). Slowly ease
the Hamper Dump Rope back, keeping even
pressure, until the Hamper returns back down.
CAUTION: DO NOT ALLOW THE HAMPER DUMP
ROPE TO HAVE TOO MUCH SLACK IN IT WHEN
OPERATING. THE ROPE CAN GET CAUGHT IN
THE BRUSHES CAUSING INJURIES.
Pull Hamper
Dump Rope
Low
High
Fig. 7
Fig. 8
Height
Adjustment
Tube
MAINTENANCE:
Lubrication: Remove wheel by removing plastic hubcap and snap
ring. Apply a light multipurpose grease to wheel gear and pinion
gear. NOTE: DO NOT allow grease to enter center of pinion gear.
Lubricate at the beginning of each season or more often as
conditions dictate. See Fig. 9.
Remove pinion gear and oil pawl with SAE #20 or equivalent. Do
not apply grease or heavy oil to pawl. This causes the pawl to stick
and operate erratically. When installing pinion and pawl, refer to
Fig 10 for correct position.
Apply SAE #20 oil or equivalent to brush axle bearings twice a
season. Oil Hamper pivot pins occasionally to prevent rust and
insure easy dumping.
Fig 9
Plastic Hubcap
Wheel
Snap Ring
Pinion Gear
Pawl
Sweeping Direction
Left Side Pinion
Gear & Pawl
Right Side Pinion
Gear & Pawl
Fig. 10
Brush Replacement:
Remove the Hex Head Bolts holding on the
Brush Clamps. Place Brush Strips in slots of brush
disc so shorter supporting bristles are away from
brush sweeping rotation. Place the Brush Clamp
against the Brushes and tightly secure with the
Hex Head Bolts into the nut on the Brush Axle.
See Fig. 11
Fig. 11
Hex Head Bolt
Hex Head Bolt
Brush Clamp
Brush Clamp
Brushes
Nut on
Brush Axle
Step 1
Attach the Leg Stands (M) to the Chassis Assembly (B) rear tube using four 1/4” x 1-3/8” Hex Head Bolts and
securing with four 1/4” Nylon Lock Nuts.
Step 2
Attach the Height Adjustment Tube (K) to the chassis Bumper Assembly using a 5/16” x 1-3/4” Hex Head Bolt
and a 5/16” Nylon Lock Nut. Connect one end of the Spring to one side of the bracket then stretch around the
Height Adjustment Tube and connect the other end of the spring to the opposite side of the bracket.
Step 7
Insert the Hamper Dump Rope through
center hole on the Sweeper Chassis Assembly.
Next, lay the Hamper Dump Rope behind the
sweeper. Fig. 4
Install the Hamper Assembly onto the frame
assembly. The Hamper Pivot Bracket Assemblies
fit inside the slots on both Pivot Brackets on the
frame of the sweeper. Fig. 5
The Hamper Dump Rope needs to go under
and up the back side of the Hamper Assembly
for proper dumping operation. Tie the Hamper
Dump Rope end to the center of the Top Hamper
Cross Brace. Fig. 6
Hamper Dump
Rope
Hamper Dump
Rope
Top Hamper
Cross Tube
STORAGE:
For long term storage, you can remove the
Tube Frame Assembly (both RH and LH Side
Frame and Top Frame Tube) and the Fiberglass
Hamper Support Rods on the Hamper Assembly
to reduce total storage area.
NOTE: ALL REFERENCES TO “RIGHT” (RH), AND “LEFT” (LH) DIRECTIONS ARE IN REFERENCE TO POSITION BEHIND SWEEPER.
Fig. 4
Fig. 6
Hamper Dump
Rope
1/4” x 1-3/8” Hex
Head Bolts
1/4” Nylon
Lock Nuts
Leg Stands
Height Adjustment
Tube
Spring
5/16” x 1-3/4”
Hex Head Bolt
5/16” Nylon
Lock Nut
Bracket
1/4” Nylon
Lock Nuts
Tube Frame Assembly
Hamper Assembly with
Fiberglass Hamper Support
Rods removed
Hamper Pivot
Bracket on Frame
Fig. 5
Step 5
Insert both Top Hamper Side Tubes (I) through the
loop on the fabric of the hamper (Outlined). Secure
to the Top Hamper Cross Tube using the spring button
located on the ends. Fig .1
Place the Bottom Hamper Cross Tube (E) into the
hamper basket assembly with the holes facing up.
Next, insert the Bottom Hamper Side Tubes (J)
on each end of the Bottom Hamper Cross Tube.
Fig. 2
Attach first, the Bottom Hamper Side Tube to the
Hamper Tie Rod (inside the fabric of the hamper)
followed by the Top Hamper Side Tube. Secure
each side of the Hamper Tie Rod with two
5/16” Nylon Lock Nuts. Fig. 3
Attach the optional Wind Apron to the
outside tubes towards the front of the
Hamper Assembly.
The Wind Apron helps keep debris from
blowing out of the Hamper Assembly while
the unit is in use.
Wind Apron
Step 3
Insert both the RH Hitch Arm Tube (L) and the LH Hitch Arm Tube (O) through the holes in the Chassis Assembly
as shown. Attach both Hitch Arm Tubes to the Chassis Assembly using four 1/4” x 1-3/8” Hex Head Bolts and
four 1/4” Nylon Lock Nuts. DO NOT TIGHTEN THESE BOLTS COMPLETELY YET!
Next, insert the 5/16” x 2-3/4” Hex Head Bolt through the end of both Hitch Arm Tubes and thread a 5/16” Nylon
Lock Nut onto it. DO NOT TIGHTEN THIS BOLT YET EITHER.
Attach the Clevis Plates to the Hitch Arm Tubes using two 5/16” x 1-3/4” Hex Head Bolts and two 5/16” Nylon
Lock Nuts. DO NOT TIGHTEN THESE BOLTS YET.
First tighten the 5/16” x 2-3/4” Hex Head Bolt and Lock Nut. Next, Tighten the two 5/16” x 1-3/4” Hex Head
Bolts and Lock Nuts. Finally, Tighten the 1/4” x 1-3/8” Hex Head Bolts and Lock Nuts connecting the Hitch Arm
Tubes to the Chassis Assembly.
Insert the Clevis Pin in through the holes on the end of the Clevis Plates and secure with the Hitch Pin Clip.
Fig. 1
Fig. 2 Fig. 3
Top Hamper
Side Tube
Hamper Fabric
Spring Button
Top Hamper Cross Tube
Bottom Hamper Cross Tube
Bottom Hamper Side Tubes
Hamper Tie Rod (inside fabric) Hamper Tie Rod
5/16” Nylon
Lock Nut
Top Hamper
Side Tube
Bottom Hamper
Side Tube
Step 6
Insert one end of the Fiberglass Hamper Support
Rod (H) into the hole on the Top Hamper Cross
Tube (you may have to move the fabric together
to find). Bend the Fiberglass Hamper Support Rod
and pull up on the Top Hamper Cross Tube to
insert the other end of the rod into the hole located
on the Bottom Hamper Cross Tube. Repeat this for
the other side.
Fiberglass Hamper Support Rod
Top Hamper
Cross Tube
Bottom Hamper
Cross Tube
RH Hitch
Arm Tube
LH Hitch
Arm Tube
1/4” x 1-3/8” Hex
Head Bolts
1/4” Nylon
Lock Nuts
Clevis Plates
Clevis Pin
Hitch Pin
Clip 5/16” Nylon
Lock Nuts
5/16” x 1-3/4”
Hex Head Bolts
5/16” x 2-3/4”
Hex Head Bolt
5/16” Nylon
Lock Nut
1/4” x 1-3/8” Hex
Head Bolts
1/4” Nylon
Lock Nuts
Step 4
Attach both Side Frame Tubes (N) to the ends
of the Hitch Arm Tubes using two 1/4” x 1-3/8” Hex
Head Bolts and two 1/4” Nylon Lock Nuts. Be sure
to attach the bolts from inside to out. This eliminates
any chances of the hamper bag snagging and ripping
during use. Next, insert the Top Frame Tube (F) inside
both upper ends of the Side Frame Tubes. Attach both
Hamper Pivot Brackets (C) (on the outside of the tubes)
using 1/4” x 1-3/8” Hex Head Bolts and 1/4” Nylon
Lock Nuts.
Side Frame
Tube
Top Frame Tube
Side Frame
Tube
Hitch Arm
Tube
1/4” x 1-3/8”
Hex Head Bolt
1/4” Nylon
Lock Nut
LH (Left Hand)
Hamper Pivot
Bracket
1/4” x 1-3/8”
Hex Head Bolt

Other Precision Lawn Sweeper manuals

Precision LSP48 User manual

Precision

Precision LSP48 User manual

Precision SW45PRE User manual

Precision

Precision SW45PRE User manual

Popular Lawn Sweeper manuals by other brands

Craftsman 486.242223 owner's manual

Craftsman

Craftsman 486.242223 owner's manual

Lawn Tender SW380LT owner's manual

Lawn Tender

Lawn Tender SW380LT owner's manual

Agri-Fab 45-0337 repair parts

Agri-Fab

Agri-Fab 45-0337 repair parts

The Handy THTLS38 Operator's manual and parts list

The Handy

The Handy THTLS38 Operator's manual and parts list

Yardwise Sweep It 23630YW Assembly manual

Yardwise

Yardwise Sweep It 23630YW Assembly manual

Craftsman 486.24029 Operator's manual

Craftsman

Craftsman 486.24029 Operator's manual

Agri-Fab 45-03371 owner's manual

Agri-Fab

Agri-Fab 45-03371 owner's manual

Craftsman 486.242211 owner's manual

Craftsman

Craftsman 486.242211 owner's manual

Ohio Steel 42SWP22 operating instructions

Ohio Steel

Ohio Steel 42SWP22 operating instructions

Steiner Turf LS340 Operator's manual & illustrated parts

Steiner Turf

Steiner Turf LS340 Operator's manual & illustrated parts

Craftsman 486.24209 owner's manual

Craftsman

Craftsman 486.24209 owner's manual

SNOWJOE SUNJOE SJSW26M-RM Operator's manual

SNOWJOE

SNOWJOE SUNJOE SJSW26M-RM Operator's manual

Agria 2294 071 operating instructions

Agria

Agria 2294 071 operating instructions

Redexim RTC BRUSH user manual

Redexim

Redexim RTC BRUSH user manual

Brinly STS-427LXH owner's manual

Brinly

Brinly STS-427LXH owner's manual

Ryobi P2105 Operator's manual

Ryobi

Ryobi P2105 Operator's manual

Husqvarna 326SX-SERIES Operator's manual

Husqvarna

Husqvarna 326SX-SERIES Operator's manual

Husqvarna 325L X Series Operator's manual

Husqvarna

Husqvarna 325L X Series Operator's manual

manuals.online logo
manuals.online logoBrands
  • About & Mission
  • Contact us
  • Privacy Policy
  • Terms and Conditions

Copyright 2025 Manuals.Online. All Rights Reserved.