Premier Mounts UNI-PDS User manual

www.mounts.com | North America 800.368.9700 | International [phone] | Europe [phone]
1321 S. State College Blvd., Fullerton, CA 92831 USA
Warranty, Garantie, Garantía, Garanzia, Garantie, Waarborg: http://www.mounts.com/warranty
9530-010-001-0X Rev.8
Installation Guide
Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids
UNI-PDS/UNI-EPDS

UNI-PDS/UNI-EPDS
Page 2 Visit the Premier Mounts website at http://www.mounts.com Installation Instructions
Table of Contents
PREMIER MOUNTS DOES NOT WARRANT AGAINST DAMAGE CAUSED BY THE USE OF ANY PREMIER MOUNTS PRODUCT FOR
PURPOSES OTHER THAN THOSE FOR WHICH IT WAS DESIGNED OR DAMAGE CAUSED BY UNAUTHORIZED ATTACHMENTS OR
MODIFICATIONS, AND IS NOT RESPONSIBLE FOR ANY DAMAGES, CLAIMS, DEMANDS, SUITS, ACTIONS OR CAUSES OF ACTION
OF WHATEVER KIND RESULTING FROM, ARISING OUT OF OR IN ANY MANNER RELATING TO ANY SUCH USE, ATTACHMENTS OR
MODIFICATIONS.
SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE ASSEMBLY OF THIS PRODUCT. USE PROPER
SAFETY GEAR AND TOOLS FOR THE ASSEMBLY PROCEDURE TO PREVENT PERSONAL INJURY.
At least two qualied people should perform the assembly procedure. Injury and/or damage can result from dropping or mishandling the
projector.
If mounting to studs, make sure that the mounting screws are anchored into the center of the studs. Use of an edge-to-edge stud nder is
recommended.
Be aware of the mounting environment. If drilling and/or cutting into the mounting surface, always make sure that there are no electrical wires in
wall. Cutting/drilling into an electrical line may cause serious injury.
This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal injury.
Do not install near sources of high heat. Do not install on a structure that is prone to vibration, movement or chance of impact
Contact Premier Mounts with any questions
[phone]
[email protected]
PRIOR TO THE INSTALLATION OF THIS PRODUCT, THE INSTALLATION INSTRUCTIONS SHOULD BE READ AND COMPLETELY UN-
DERSTOOD. THE INSTALLATION INSTRUCTIONS MUST BE READ TO PREVENT PERSONAL INJURY AND PROPERTY DAMAGE. KEEP
THESE INSTALLATION INSTRUCTIONS IN AN EASILY ACCESSIBLE LOCATION FOR FUTURE REFERENCE.
Make sure there are no water lines inside the wall where the mount is to be located. Cutting/drilling into a water line may cause severe water
damage to the mounting surface.
Weight Capacity
Maximum projector weight: 50 lb. THE WALL STRUCTURE MUST BE CAPABLE OF HOLDING FIVE
(5) TIMES THE WEIGHT OF THE PROJECTOR. IF NOT, THEN THE
WALL STRUCTURE MUST BE REINFORCED.
Warning Statements
Weight Capacity 2
Warning Statements 2
Installation Tools 3
Parts List 3
PDS-PLUS-STA/PDS-PLUSW-STA Mounting Hardware 4
Lock-It™ Security Pack 4
Determining the Installation Height 5
Wood Stud Installation 6
Attaching the Projector Arm 7
Throw Distance Calculation 8
Adjustable Mounting Bracket Installation 9
Attaching the Base Box to the Adjustable Mounting Bracket 10
Extension Arm Installation (Optional) 10
Low Prole Bracket Installation 11
Attaching the Base Box to the Upper Mounting Plate 11
Attaching the Universal Projector Plate 12
Attaching the Projector 16
Base Box Adjustment 16
Set Screw Installation 17
Utilizing the Storage Feature 17
Cable Management 18
Technical Specications 19
Warranty 20
Disclaimer 20

UNI-PDS/UNI-EPDS
Installation Instructions Visit the Premier Mounts website at http://www.mounts.com Page 3
Wall Plate
(Qty 1)
Arm Assembly
(Qty 1)
Adjustable Mounting Assembly
- Pre-Assembled (Qty 1)
End Cover
(Qty 1)
M5 x 8mm Security
Screws (Qty 7)
External Slide Plate
(Qty 1)
Square Washers
(Qty 4)
Phillips Screwdriver ¼˝ Drill Bit Electronic Stud Finder
Drill
Level
½˝ Socket and Socket
Wrench
Extension Arm - Optional (Qty 1)
included with the UNI-EXT
Back Plate Covers
(Qty 2)
M6 x 12mm Security
Screws (Qty 2)
Extension Hardware Pack
M6 x 12mm Security
(Qty 2)
M6 x 16mm Security
Screws (Qty 2)
M6 Flat Washer
(Qty 2)
Internal Slide Plate
(Qty 1)
Parts List
Installation Tools
The following tools may be required depending upon your particular installation. They are not included.
Make sure your Premier Mounts product has the following hardware and components before beginning installation. If
there are parts missing and/or damaged, stop the installation and call Premier Mounts at [phone].
UNI-PDS/UNI-EPDS Hardware
5
16˝ x 3˝ Lag Bolts
(Qty 4)
Projector Bracket
(Qty 1)
Mounting Legs - Long
(Qty 4)
Mounting Legs - Short
(Qty 4)
⅛˝ Nylon Spacer
(Qty 2)

UNI-PDS/UNI-EPDS
Page 4 Visit the Premier Mounts website at http://www.mounts.com Installation Instructions
PDS-PLUS-STA/PDS-PLUSW-STA Mounting Hardware
Parts List (cont’d)
M2.5 x 12mm Screw
(Qty 4)
M3 x 16mm Screw
(Qty 4)
M4 x 12mm Screw
(Qty 4)
M5 x 12mm Screw
(Qty 4)
M6 x 12mm Screw
(Qty 8)
M3 Flat Washer
(Qty 10)
M6 x 8mm Set Screw
(Qty 1)
Base Box
(Qty 1)
¼˝ - 20 x 5
16˝ Screw
(Qty 1)
External Tooth Washer
(Qty 4)
M6 x 12mm Phillips Head
w/Integrated Split Washer
(Qty 12; 6 pre-installed)
M2.5 x 10mm Phillips Pan Head
Screw (Qty 4)
M3
M5
M6 x 8mm Security Set Screw
(Qty 1)
M2.5 x 12mm Security
Screw (Qty 4)
M3 x 16mm Security
Screw (Qty 4)
M4 x 12mm Security
Screw (Qty 4)
M5 x 12mm Security
Screw (Qty 4)
M6 x 12mm Security
Screw (Qty 8)
M3 Flat Washer
(Qty 10)
M6 x 12mm Security Head
w/Integrated Split Washer
(Qty 12)
Security Wrenches
(Qty 2)
Lock-It™ Security Pack
Nylon Spacer
(Qty 2)
Flat Washer
(Qty 2)
¼˝ - 20 x 5
16˝ Security Screw
(Qty 1)
M2.5 x 10mm Security
Screw (Qty 4)

UNI-PDS/UNI-EPDS
Installation Instructions Visit the Premier Mounts website at http://www.mounts.com Page 5
 Measure distance from center of lens to the top of the PDS-PLUS bracket (C).
 Add the distance from the ground to the top of the screen (A). Add the projector manufacturers recommended
offset from the projector manual (B). Add the measurement from Step 1 (C), and then add 2.5˝ to the total.
(Example: A + B + C + 2.5˝ = ?)
 Add the measurements to determine the mounting height mark. Place a mark at the top of the total calculated height measurement starting from the ground up.
This mark will represent the lower edge of the wall plate.
Refer to the projectors User’s Manual to determine the offset of the projector lens to the top of the
screen/whiteboard (B).
Lens
PDS-PLUS Bracket
Projector
In order to determine the installation height and throw distance, the PDS-PLUS projector bracket must be mounted
to the projector. Please refer to the PDS-PLUS Installation Instructions prior to performing the following steps.
Top of Screen
Mark
Legend
A - Distance from ground to the top of the
screen/whiteboard (viewable area).
B - Manufacturers recommended offset
measurement. This measurement will
be listed in the Users Manual.
C - Center of the lens to the top of the
projector bracket.
Add 2.5˝ to the calculated total.
This total distance will be the location for the bottom rail on
the wall plate.
Proceed to the “Wood Stud Installation” section.
Ground
Determining the Installation Height

UNI-PDS/UNI-EPDS
Page 6 Visit the Premier Mounts website at http://www.mounts.com Installation Instructions
THE EXACT CENTER OF THE STUD MUST BE LOCATED FOR CORRECT AND SAFE INSTALLATION.
Use an electronic stud nder (not supplied) to
locate the center of the stud that is in the wall. Wood Stud
Stud nder
Height
Mark
(from page 5)
Wood Stud
Marking
Wall
Plate
Do NOT over-tighten lag bolts when attaching the mount to the wall. Improper installation may result in personal
injury or damage to property.
Once the mounting points have been marked, use a
¼˝ drill bit and portable drill to drill the pilot holes.
Drill Marking
Wood Stud Installation
Mounting Point
Mark
Step 1
Step 2
Step 4
Use a pencil to mark the rst mounting point, just
above your height mark (from page 5).
Step 3
 Use the level to make sure the wall plate is level from side to side.
 Place the wall plate over the rst mounting point mark and use a pencil to
mark the rest of the mounting points.
Four (4) mounting points must be used. Two (2)
upper mounting points and two (2) lower mounting
points.

UNI-PDS/UNI-EPDS
Installation Instructions Visit the Premier Mounts website at http://www.mounts.com Page 7
 Locate the mounting hook cutout on the top of the wall plate.
 Tilt the arm slightly and gently insert the mounting hooks into the mounting
hook cutouts.
 Slowly lower and let the projector arm rest against the wall plate.
Mounting Hook Cutout
Mounting Hooks
Wall Plate
Projector Arm
MAKE SURE THE PROJECTOR ARM IS FULLY
SEATED BEFORE RELEASING THE UNIT.
Attaching the Projector Arm
If using the storage feature of the product, it
may be easier to route any wiring at this time
(please see Page 12).
After the pilot holes have been drilled, use four (4)
5
16˝ x 3˝ lag bolts and four (4) square washers to
mount the wall plate to the wooden studs.
Use a ½˝ socket and socket wrench to nish this step.
Socket
Lag Bolt and Square Washer
Wall
Plate
Proceed to the “Attaching the Projector Arm” section.
Back Plate Covers
Step 6
Step 5
Insert and gently tap the upper and lower back plate covers into place.
Step 1

UNI-PDS/UNI-EPDS
Page 8 Visit the Premier Mounts website at http://www.mounts.com Installation Instructions
Please review the Operator’s Manual that came packaged with your projector before attaching the upper
mounting bracket. The correct throw distance (the distance from the projector to the screen) must be
determined prior to mounting the projector.
 Refer to the projectors Users Manual to determine the
distance from the lens to the front of the screen (X).
 Measure the distance from the front of
the lens to the center of the projector (Y).
 Measure the distance from the wall to the face of the
whiteboard/screen (Z).
 Add all measurements (X + Y + Z) to
determine projector placement on the arm assembly. This
measurement will determine where the center of the mount
bracket will be located on the arm assembly. Please make
note of this measurement.
Front Lens
Rear Lens
Calculations
X = Manufacturers recommended
throw distance
Z = Distance from wall to face of
whiteboard/screen
Front Lens Throw Distance =
(X + Y + Z)
Rear Lens Throw Distance =
(X - Y + Z)
Throw Distance Calculation
The UNI-PDS/UNI-EPDS can be also used as
a wall-mounted standard projector mount as
well as a short throw projector mount. Align
the projector facing the opposite direction
from the wall plate to project the image
across the room. Please take into account
the projectors throw capabilities prior to
mounting in the projector opposite direction
 Locate the two (2) lock mounting points on the projector arm. These two
points will be aligned with the lock mounting points on the wall plate.
 Using a security wrench, insert and tighten two (2)
M5 x 8mm security head screws.
Do NOT overtighten these screws.
Step 2
Lock Mounting
Point
M5 x 8mm Security
Head Screw
Security Wrench
Proceed to the “Throw Distance Calculation” section.
Proceed to the “Adjustable Mounting Bracket
Installation” section.

UNI-PDS/UNI-EPDS
Installation Instructions Visit the Premier Mounts website at http://www.mounts.com Page 9
Security
Wrench
 If needed, determine the Throw Distance
again.
 Once the correct throw distance has been
determined, use the security wrench (supplied) to tighten the
mounting screws.
Do NOT overtighten these screws.
If the adjustable mounting bracket needs
to be adjusted, the four (4) M6 x 12mm
security screws may be loosened so that
the bracket can be moved ±2˝. Once the
desired height has been achieved,
re-tighten the hardware.
 Insert the inner slide plate into the
projector arm.
 Determine which adjustment slot best
matches your throw distance
calculation (above).
 Raise the adjustable mounting bracket
into position.
 Align the mounting holes of the upper
mounting plate with the mounting holes
of the inner slide plate.
Two (2 - one per screw) ⅛˝ nylon
washers must be placed between the
adjustable mounting bracket and the
projector arm (see inset to the right).
 Secure and nger-tighten two (2)
M6 x 16mm security head screws.
Projector Arm
Inner Slide
Plate
Adjustable
Mounting
Bracket
M6 x 16mm
Security
Screw
Adjustment
Slot
Calculated
Throw
Distance
⅛˝ Nylon
Washer
Adjustable Mounting Bracket Installation
Upper Mounting
Plate
If using the optional extension arm,
proceed to Page 10.
Proceed to the “Attaching the Base Box to the
Adjustable Mounting Bracket” section.

UNI-PDS/UNI-EPDS
Page 10 Visit the Premier Mounts website at http://www.mounts.com Installation Instructions
 Raise the base box to the upper mounting bracket.
 Align the two (2; one each side) mounting holes.
 Using a security wrench, insert and tighten two (2) M6 x 12mm security
head screws.
 Attach the projector to the base box, referring to the PDS-PLUS
installation instructions for nal adjustments.
Attaching the Base Box to the Adjustable Mounting Bracket
The M6 x 12mm security head screws must be
mounted from the underside of the base box.
Base Box
M6 x 12mm Screws
Security Wrench
Adjustable Mounting
Bracket
 Slide the extension arm into the open end of the UNI-STA (the front of the
mount).
 Adjust length so that the center of the adjustable mounting bracket
matches the throw distance calibration.
 Line up the mounting holes on the extension arm with the mounting slots
on the UNI-STA.
 Using a screwdriver, insert and tighten two (2)
M6 x 12mm security head screws and M6 at washers through the
external slide plate and tighten.
 Attach the projector.
Please refer to Attaching the Base Box to the
AdjustableMountingBracket (above) for steps on
attaching the projector.
M6 x 12
Security
Screw
Security Wrench
M6 Flat
Washers
Adjustable
Mounting
Bracket
UNI-STA
If the extension arm is purchased at a later date, the end cover must be removed prior to installing the extension
arm.
Please see the Operator’s Manual to determine the correct throw distance (the distance from the projector to the
screen). The throw distance must be determined prior to mounting the projector (Page 8).
Extension Arm
(Optional)
Extension Arm Installation (Optional)
External Slide
Plate
Do NOT overtighten these screws.
Proceed to the “Low Prole Bracket Installation”
section.

UNI-PDS/UNI-EPDS
Installation Instructions Visit the Premier Mounts website at http://www.mounts.com Page 11
 Raise the base box to the upper mounting bracket.
 Align the two (2; one each side) mounting holes.
 Using a security wrench, insert and tighten two (2) M6 x 12mm security
head screws.
 Attach the projector to the base box, referring to the PDS-PLUS
installation instructions for nal adjustments.
Please review the installation instructions that
came packaged with the projector before
attaching the projector to the upper mounting
bracket.
Do not overtighten the screws.
Low Prole Bracket Installation
Attaching the Base Box to the Upper Mounting Plate
M6 x 12mm Screws
M5 Security Wrench
Adjustable Mounting Bracket
 Using a M5 security wrench, remove the four (4) M6 x 12mm security
screws by rotating the security wrench counterclock-wise.
 Slide the adjustable mounting bracket off the upper mounting bracket.
Proceed to the “Attaching the Base Box to the Upper
Mounting Plate” section.
Upper Mounting Bracket
The M6 x 12mm security head screws must be
mounted from the underside of the base box.
Projector dimensions differ between
manufacturers. If the projector hangs too low from
the UNI-PDS/UNI-EPDS, the adjustable mounting
bracket may be removed. This will allow you to
attach the base box directly to the upper mounting
bracket for an even lower prole installation.
Base Box M6 x 12mm Screws Security Wrench
The PDS-PLUS comes with optional security
hardware (Lock-It™ Security Pack) that my be
installed for added security.
Proceed to the “Attaching the Universal Projector
Plate” section.

UNI-PDS/UNI-EPDS
Page 12 Visit the Premier Mounts website at http://www.mounts.com Installation Instructions
Selecting the Mounting Hardware
 Insert a small straw or toothpick into the threaded inserts found on the
bottom or top of the projector.
 Use a pencil to mark the depth of the threaded insert on the small straw or
toothpick.
 Mark the straw or toothpick 1/8” above the depth of the threaded insert, as
shown in Figure 1.
 Insert the small straw or toothpick into the remaining threaded inserts to
compare and verify their depth using the straw or toothpick’s 1/8” allowance
mark.
 Locate the correct diameter screw for the threaded insert.
If the screw you selected is longer than the 1/8” allowance mark on the
small straw or toothpick, as shown in Figure 2 and Figure 3, do not use
this screw. The screw length must not bypass the mark.
 Test each size of the screws provided.
The correct screws should thread easily into the mounting point and not pull
out when tension is applied.
Does your projector have multiple mount points or a single mount point?
If your projector has multiple mount points, proceed to the “Multiple
Mount Point Installation” section.
If your projector has a single mount point, skip to the “Single Mount
Point Installation” section.
Attaching the Universal Projector Plate
Small Straw or Toothpick
Small Straw
or Toothpick
Small Straw
or Toothpick
Marking the 1/8”
Allowance
Depth Plus 1/8” Allowance
Mark
Depth Plus 1/8” Allowance
Mark

UNI-PDS/UNI-EPDS
Installation Instructions Visit the Premier Mounts website at http://www.mounts.com Page 13
Multiple Mount Point Installation
Step 1
 Locate the projector’s mount points.
 Position an appropriate number of mounting legs on the projector.
You can use any combination of three (3) or more long mounting legs and short
mounting legs, depending on the number and location of the thread inserts on
your projector.
The number and placement of mount points on projectors varies
between projector manufacturers. This example projector has ve (5)
mount points, but only uses four (4) mounting legs.
Step 2
Insert the mounting hardware, as determined in the “Selecting the Mounting
Hardware” section, through the leveling barrel into the thread insert of the
projector.
You can use either the standard Phillips head or Lock-It™ security
hardware.
Do not tighten the mounting hardware at this time.
Attaching the Universal Projector Plate (cont’d)
Mounting Hardware Too Long?
The depth of some projector mount points may prevent you from
tightening the M2.5 and M3 mounting hardware.
You can reduce the length of the M2.5 and M3 mounting hardware
by stacking up to a maximum of ve (5) M3 at washers inside the
leveling barrel.
Avoid stacking too many M3 washers; the mounting hardware must
thread into the projector mount point at least four (4) complete
turns.

UNI-PDS/UNI-EPDS
Page 14 Visit the Premier Mounts website at http://www.mounts.com Installation Instructions
Attaching the Universal Projector Plate (cont’d)
Step 3
Raise or lower each of the mounting legs, by rotating the leveling barrels, until all
of the mounting legs are at an equal height.
• Lower the mounting leg by rotating the leveling
barrel counter-clockwise.
• Raise the mounting legs by rotating the leveling
barrel clockwise.
 Identify the projector’s approximate front-to-back center of gravity. Place
your hands on each side of the projector and gently lift it an inch from the
surface on which it is resting. Carefully adjust your grip on the projector until
it seems balanced from front-to-back. Mentally note the apparent center of
gravity.
 Identify the projector’s approximate side-to-side center of gravity. Place your
hands on the front and back of the projector and gently lift it an inch from the
surface on which it is resting. Carefully adjust your grip on the projector until
it seems balanced from side-to-side. Mentally note the apparent center of
gravity.
 Place the Universal Projector Plate on top of the mounting legs with the
center hole as close as possible to the projector’s center of gravity.
Step 4
Step 5
 Verify that the mounting legs are at an equal height. Return to Step 3 if
they are not at an equal height or the Universal Projector Plate is not level.
 Verify the position of the integrated sliding M6 square nut in the mounting leg
relative to a nearby slot on the Universal Projector Plate.
If the M6 square nut is not aligned with any slot, you can use any thin
implement, such as a toothpick, to nudge it into alignment.
Side-to-Side
Center of Gravity Front-to-Back
Center of Gravity
Sliding M6
Square Nut

UNI-PDS/UNI-EPDS
Installation Instructions Visit the Premier Mounts website at http://www.mounts.com Page 15
Attaching the Universal Projector Plate (cont’d)
Step 7
 Attach the Universal Projector Plate to each of the mounting legs by inserting
and tightening one (1) M6 x 12mm screw through the Universal Projector
Plate into the M6 square nut on each of the mounting legs.
 Insert one (1) Barrel Cap into the end of each leveling barrel.
Single Mount Point Installation
A single ¼-20 x 5/16″ screw must be used to attach the Universal Projector Plate
to the projector if your projector has only one mounting point.
Do not overtighten the mounting screws.
You can use either the standard Phillips head or
Lock-It™ security hardware.
Proceed to the “Attaching the Projector” section.
Step 6
Tighten the mounting screws to the projector.
Do not overtighten the mounting screws.
Proceed to the “Single Mount Point Installation” section.
Do not overtighten the mounting screws.
You can use either the standard Phillips head or Lock-It™
security hardware.

UNI-PDS/UNI-EPDS
Page 16 Visit the Premier Mounts website at http://www.mounts.com Installation Instructions
Attaching the Projector
 Insert the four (4) M6 x 12mm tilt adjustment screws, two (2) per side.
You can use either the standard hardware or Lock-It™ security hardware.
 Tighten all screws.
Do not overtighten the mounting screws.
 Follow the PDS Installation Instructions to complete the installation.
 Place one (1) nylon washer and one (1) ¼″ at washer over the hinge pin.
 Insert and tighten one (1) M6 x 12mm screw.
 Repeat 1 and 2 for the opposite hinge pin.
You can use either the standard hardware or Lock-It™ security hardware.
Replace eight (8) M6 x 12mm screws and one (1) M6 x 8mm set screw.
Do not overtighten the M6 x 12mm screws or the M6 x 8mm set screw.
 Slide the projector / Projector Plate assembly onto the PDS Base Box.
 Hook the Projector Plate over the hinge pins, as shown.
Base Box Adjustment
 You can adjust the roll of the projector by loosening the three (3) front and
rear M6 x 12mm screws.
Do not fully loosen the screws, as the mount may drop.
 Set the desired roll and then tighten the screws. First tighten the center
screws and work your way to the outside screws, making any nal
adjustments prior to tightening the last two screws.
 You can adjust the tilt of the projector by loosening the two (2) M6 x 12mm
screws on each side of the Base Box.
 Set the desired tilt and then tighten the screws, making any nal adjustments
prior to tightening the last two screws.
If your projector is not holding the tilt, install the four (4) external tooth
washers on the four (4) M6 x 12mm Phillips head screws w/ Integrated
Washers.
 Once all adjustments have been made, tighten all hardware.

UNI-PDS/UNI-EPDS
Installation Instructions Visit the Premier Mounts website at http://www.mounts.com Page 17
The M6 set screw will be used in conjunction with
any standard threaded adapter (sold separately).
 Thread in threaded adapter until
securely fastened.
 Thread in one (1) M6 x 6mm set screw.
 Use an M3 security wrench to tighten the
M6 set screw (included in the PDS-PLUS
hardware).
Upper Mounting
Bracket
M6 Set Screw
M3 Security
Wrench
Set Screw Installation
The security set screw will prevent the unit
from being removed and from being knocked
out of adjustment.
The storage feature may be used to store electronic
components. There is an accessible door on each side of the
storage enclosure. It may be securely held shut with the use of
four (4) M5 x 8mm security head screws. It may be easiest to
pre-wire all cables down the arm (or extension) at this time.
Electronic
Components
Door
Security
Wrench
M5 x 8mm
Security Screw
 Open the storage door that is located on the
side of the wall plate.
 Place the electronic components inside the
storage enclosure.
 Make all electronic connections at this time.
 Close the storage door and secure using two
(2; 1 upper and 1 lower) M5 x 8mm security
head screws. Tighten using a security wrench.
Repeat this process for the other side as well.
Utilizing the Storage Feature
Proceed to the “Utilizing the Storage Feature”
section.
Proceed to the “Cable Management” section.

UNI-PDS/UNI-EPDS
Page 18 Visit the Premier Mounts website at http://www.mounts.com Installation Instructions
UNI-STA
UNI-EXT
 The cable access holes are located at the end of the short throw mount
and on the wall plate.
 Route the cables through one end of the UNI-PDS/UNI-EPDS and out the
other end.
 Attach the end cover with an M5 x 8mm security head screw.
Cable Management
You may direct the cables out the end of the
UNI-PDS/UNI-EPDS. The end cover has a
perforated tab to allowcables to pass out the end.
Pliers must be used to bend the perforated tab. If
the cables will not t, the end cover may be
removed by loosening and extracting the
M5 x 8mm security screw.
UNI-PDS/UNI-EPDS
M5 x 8 Security
Screw
End Cover
Extension Bracket
Perforated Tab
Electronic
Components
Cables
Cable Opening
Projector
Hook-Ups
Electronic
Components
Electronic
Components
Cables
Cable Opening
Projector
Connections
Cable Opening

UNI-PDS/UNI-EPDS
Installation Instructions Visit the Premier Mounts website at http://www.mounts.com Page 19
All measurements are in inches(mm).
Technical Specications

UNI-PDS/UNI-EPDS
Page 20 Visit the Premier Mounts website at http://www.mounts.com Installation Instructions
PREMIER MOUNTS
LIMITED LIFETIME WARRANTY
What and Who is Covered by this Limited Warranty and for How Long
Premier Mounts warrants this product to be free from defects in material and workmanship for the lifetime of the original
owner of this product. The limited warranty is valid only for the original purchaser of the product.
What Premier Mounts Will Do
At the sole option of Premier Mounts, Premier Mounts will repair or replace any product or product part that is defective.
If Premier Mounts chooses to replace a defective product or part, a replacement product or part will be shipped to you at
no charge, but you must pay any labor costs.
What is Not Covered; Limitations
PREMIER MOUNTS DISCLAIMS ANY LIABILITY FOR DAMAGE TO MOUNTS, ADAPTERS, DISPLAYS, PROJEC-
TORS, OTHER PROPERTY, OR PERSONAL INJURY RESULTING, IN WHOLE OR IN PART, FROM IMPROPER
INSTALLATION, MODIFICATION, USE OR MISUSE OF ITS PRODUCTS.
PREMIER MOUNTS DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. PREMIER MOUNTS IS NOT RESPON-
SIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO, INABILITY TO
USE ITS PRODUCTS OR LABOR COSTS FOR REMOVING AND REPLACING DEFECTIVE PRODUCTS OR PARTS.
SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAM-
AGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.
What Customers Must Do for Limited Warranty Service
If you discover a problem that you think may be covered by the warranty you MUST REPORT it in writing to the address
below within thirty (30) days. Proof of purchase (an original sales receipt) from the original consumer purchaser must
accompany all warranty claims. Warranty claims must also include a description of the problem, the purchaser’s name,
address, and telephone number. General inquiries can be addressed to Premier Mounts Customer Service at 1-800-
368-9700. Warranty claims will not be accepted over the phone or by fax.
Premier Mounts
Attn: Warranty Claim
3130 East Miraloma Ave.
Anaheim, CA 92806
How State Law Applies
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH
VARY FROM STATE TO STATE.
Warranty
Premier Mounts intends to make this manual accurate and complete. However, Premier Mounts makes no claim that
the information contained herein covers all details, conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this product. The information contained in this document is subject to
change without notice or obligation of any kind. Premier Mounts makes no representation of warranty, expressed or implied,
regarding the information contained herein. Premier Mounts assumes no responsibility for accuracy, completeness or
sufciency of the information contained in this document.
Disclaimer