Price Pfister Ashfield 531 Series User manual

A COMPANY
Copyright © 2007, Price Pfister, Inc.
1-25-07 EO7052D 30603-0200
531 Series
Serie 531
Série 531
Two Handle Kitchen Pull-Out Faucet
Grifo De Extracción Para Cocina Con Dos Manijas
Mitigeur De Cuisine À Bec Arroseur Avec Deux Poignées

ENGLISH
ENGLISH
4
2
3
PRELIMINARY STEPS
5
6
Thank you for purchasing this Price Pfister product. All Price Pfister products are carefully engineered, and factory tested to
provide long trouble-free use under normal conditions. This product is easy to install using basic tools and our easy to follow
illustrated instructions. If you have any questions regarding this product, call 1-800-Pfaucet (1-800-732-8238).
1 BEFORE PROCEEDING
WARNING: Read all the instructions completely before proceeding. Price Pfister
recommends calling a professional if you are uncertain about installing this product!
This product should be installed in accordance with all local and state plumbing and
building codes.
2 SHUT OFF WATER SUPPLY
Locate water supply inlets and shut off the water supply valves. These are usually found
under the sink or near the water meter. If you are replacing an existing faucet, remove
the old faucet from the sink and clean the sink surface thoroughly.
3 TOOLS RECOMMENDED
• Plumber's putty • Philips head screwdriver • Pliers
• Adjustable wrench • Flashlight • Cloth
Your installation may require new supply lines and/or shut-off valves or other additional
tools.
4 CHECKING THE CONTENTS OF THE BOX
Upon opening the box, check to ensure that all of the following items are included:
A Spout Body B Valve Bodies (2X) C Pull-Out Hose
D Spray Head E Hose F Putty Rings (3X)
G Square Washers (3X) H Locknuts (3X) J Clips (2X)
K Weight L Quick Connector
If any of these items are missing, please contact Price Pfister Consumer Services at
1-800-Pfaucet (1-800-732-8238).
6 HANDLE BODY ATTACHMENT
Slide the Handle Connectors (6A) onto the Spout Bridge (6B). Push the Handle
Connectors (6A) all the way until completely seated. Be careful not to damage O-Rings
(6C). The HOT Handle Body, labeled with Red Tag (6D), should be positioned to the
left side of the spout.
5 VALVE BODY ATTACHMENT
Remove Clip (5A) from Valve Body (5B) and save.
2
6B
A
B
C
D
E
G
KL
F
H
J
5A
5A
5B
5B
6A
6A
6B
6D
6C
6C

ENGLISH
ENGLISH
FAUCET INSTALLATION
7
8
9
10
7 INSTALLING PUTTY RINGS
Following manufacturer’s recommendations on use, place a bead of plumber’s putty
in the bottom groove along the outer edge of Putty Ring (7A). Place Putty Rings (7A)
over sink holes (7B).
8 FAUCET BODY INSTALLATION
Insert the faucet Pull-out Hose (8A) through the center hole of the sink. Insert Valve
Shanks (8B) through the end holes of the sink.
9 SECURING FAUCET BODY
From underneath sink, place Square Washers (9A) onto Spout Shank (9B) and Valve
Shanks (9C). Tighten Locknuts (9D) by using Installation Tool (9E). For better leverage,
use a Screwdriver (9F), insert it through Hole (9G) and tighten the Locknuts (9D) until
Faucet Body (9H) is firmly secured to sink.
10 HOSE CONNECTION TO VALVE BODY
Slide the End Connectors (10A) onto the Valve Bodies (10B). Make sure Hose (10E)
clears Spout Shank (10F). Push the End Connectors (10A) all the way up until completely
seated. Be careful not to damage O-Rings (10C). Place Clips (10D) onto End Bodies
(10B) to secure End Connectors (10A).
3
7B
8B
10A
9A
7B
7B
7A
7A
7A
8A
8B
9A
9A
9D
9D
9D
9B
9C
9C
9E
9G
9F
9H
10A
10C 10C
10B
10D
10D
10A
10D
10B
10F
10E

ENGLISH
ENGLISH
14
FAUCET FUNCTIONS
11 13
12
15
11 PULL-OUT HOSE ATTACHMENT
From underneath sink, push Quick Connector (11A), located on the end of the Pull-Out
Hose (11B) firmly upward onto the Receiving Tube (11C), until unable to push any
further. Pull down on the Quick Connector (11A). If the housing and the Inner Collet
(11D) separate slightly but do not pull off, the Receiving Tube (11C) quick connect is
secure.
12 WEIGHT ATTACHMENT
Discard Cardboard Fitting (12B) from Weight (12A). Place Weight (12A) above the
beginning of hose bend (12C) at the spout side (as shown in shaded area). Secure
Weight (12A) with Screws (12D).
13 WATER SUPPLY CONNECTIONS
Connect water Supply Lines (13A) to Faucet Inlets (13B). Hot water supply lines go into
left inlet. Cold water supply lines go into right inlet. (Supply lines not included). Please
follow manufacturer’s instructions when installing supply lines.
14 UNIT START UP
Turn on hot and cold water supplies, and check for leaks above and below the sink.
15 FAUCET FUNCTION
COLD valve: close-counterclockwise, open-clockwise; HOT valve: close-clockwise,
open-counterclockwise. The Spout (15A) can be rotated around the Faucet Body in
any direction.
Note: Flush faucet before turning on valve (see step 18).
4
15A
13A
12B
HOT COLD
ON
HOT
COLD
11A
11B
11C
11A
11C
11A
11D
12A
12C
12D
13A
13B
13B
ON

ENGLISH
ENGLISH
MAINTENANCE & CARE
18
17
16 19
20
16 PULL-OUT OPERATION
The Spray Head (16A) can be pulled forward to spray water in any direction.
17 SPRAY OPERATION
To activate the spray mode, simply press Toggle Button (17A) located under the spray
head. You can change between spray and stream by pressing the opposite sides of the
Toggle Button (17A/17B) while the faucet is in operation. The water flow will increase by
sliding Spray Selector Switch (17C) from side to side (in spray mode only).
Note: The faucet will always turn on in regular stream mode.
18 FLUSHING
To prevent damage to the internal parts of your faucet from debris that may have
collected in the water lines, it will be necessary to flush the faucet. Flushing requires
the removal of the Spray Head (18A). To remove the Spray Head (18A), hold metal
Hose Fitting (18B) and turn the Spray Head (18A) counterclockwise. Turn the Valve
Lever Handles (18C) to the full on position. Run water for one minute. Repeat in hot
and cold positions. Reassemble the Spray Head (18A) to the Pull-Out Hose (18D) by
turning Spray Head (18A) clockwise.
Caution: do not over tighten spray head and pull-out hose.
19 AERATOR CLEANING
Over time, the aerator in your faucet may become clogged with debris. To clean the
aerator, unscrew Aerator Housing (19A) from Spray Head (19B). Remove Aerator Seal
(19C) and Aerator Cartridge (19D) from Aerator Housing (19A). Clean Aerator Cartridge
(19D) and Aerator Housing (19A). Reassemble faucet by reversing steps.
20 HOSE REMOVAL
Turn off water supplies and relieve pressure before working on your faucet. To
remove Pull-Out Hose (20A), Push up on Quick Connector (20C). Holding Plastic Collet
(20D) in place, pull downward on Quick Connector (20C) until Tube (20E) is free. To
detach Hose Assembly (20B), remove Clips (20H) from End Valve (20F) and pull the
End Connectors (20G) from End Valves (20F).
5
19D
20A
17A
16A
18A
17B
17C
18B
18C
18C
18D
19A
19C
19B
20C
20D 20E
20B
20E
20E
20F
20F
20G
20G

ENGLISH
ENGLISH
21
22
21 HANDLE REMOVAL
Turn off water before proceeding! To remove Handles (21A), the Spout Body (21B)
must be removed. From underneath sink, remove Square Washer (21C) and Locknut
(21D) from Spout Shank (21E). Detach Decorative Button (21F), unscrew Fastener
(21G) from Handles (21A). Lift Spout Body (21B) from sink and remove Handles (21A)
from Spout Bridge (21H).
CAUTION: Maintenance
DISASSEMBLY
1. Replacement parts may be available at the store where you purchased
your faucet.
2. When replacement parts are not available, please write or call Price
Pfister Consumer Service.
3. Always turn off water and relieve pressure before working on your
faucet.
NOTE: Trim Care
Cleaning Instructions:
For all Handles and decorative finishes, use only a soft damp
cloth to clean and shine. Use of polish, detergents, abrasive
cleaners, organic solvents or acid may cause damage. Use of
other than a soft damp cloth will nullify our warranty!
Special Trim:
Trim products which contain Porcelain or other similar
substance are not acceptable for public areas or Commercial
use. Installation of Said Trim is at Users Risk!
1–800–PFAUCET (1–800–732–8238)
For Toll-Free Pfaucet information call
1–800–PFAUCET (1–800–732–8238)
or visit www.pricepfister.com
• Installation Support
• Care and Warranty Information
22 VALVE CARTRIDGE REMOVAL
Turn off water before proceeding! Remove Spout Body and Handles (see step 21).
From underneath sink, remove Square Washer (22A) and Locknut (22B) from Valve
Shanks (22C). Loosen Set Screws (22D) from Flange (22E) enough to remove Valve
Body (22F). Remove Stem Extender (22G), unscrew Cartridge Assembly (22H) and
inspect. Replace parts as necessary. 6
21C
22A
21A
21A
21D
21B
21E
21G
21G
21F
21F
21A
21H
21A
21B
22B
22C
22D
22E
22F
22G
22H

941-921*
971-034
931-041
950-025
950-121
960-077
941-713B
950-121
950-122
941-712
950-540*
951-074
951-077
931-041
951-075
910-008
951-092C
Gray
Gris
Gris
951-092B
Black
Negra
Noire
974-053C
Gray
Gris
Gris
974-053B
Black
Negra
Noire
974-053C
Gray
Gris
Gris
974-053B
Black
Negra
Noire
974-053C
Gray
Gris
Gris
974-053B
Black
Negra
Noire
900-002
Hot
Caliente
Chaud
900-003
Cold
Fría
Froid
910-024
Hot
Caliente
Chaud
910-025
Cold
Fría
Froid
Contains ASME A112.18.3-Certified check valves
Contiene válvulas de chequeo certificadas por ASME A112.18.3
Contient des valves de contrôle certifiées par ASME A112.18.3
940-973*
Left
Izquierda
Gauche
940-972*
Right
Derecha
Droite