Primare CD22 User manual









Welcome to the Primare CD22! Your CD22 is a high-quality compact disc player
with analogue and digital outputs.
SPDIF TOSlink Trigger
in/out
IR
in/out
RS-232 Not
active
Power
On/off
USB input
Analogue outputs
Digital outputs




Your CD22 is supplied with the following
components:
•Mains cable.
•C23 remote control.
•Two batteries for the remote control.
If any of these items are missing please contact
your supplier.We recommend you retain the
packaging in case you need to transport the unit
at a later date.


Analogue outputs
The analogue output provides RCA sockets for
connection to an appropriate stereo amplifier or
preamplifier.
•Connect the RCA outputs to your amplifier
or preamplifier using RCA cables.
Digital outputs
Alternatively the CD22 Compact Disc Player
provides SPDIF andTOSlink digital outputs for
connecting to a digital preamplifier or digital
surround processor.
•Connect the appropriate output to your
preamplifier or surround processor using a
suitable cable.

•Plug one end of the mains cable supplied with
the CD22 into the power connector on the
back panel, and connect the other end to a
wall socket.
If this cable is not suitable for your power outlets
please contact your supplier for an alternative
cable.
Note: See Phase , page 8, for information about
getting the best sound from your CD22.
WARNING: Always disconnect the
CD22 from the mains power before
connecting or disconnecting any cables.
•Switch on the CD22, using the switch on the
back panel.
The standby indicator will light up on the front
panel.
To switch on from standby
•Press the Obutton on the front panel or
remote control.
The display shows:
PRIMARE
Press the Obutton again to switch to standby.

•Press and hold down the */åbutton on the
front panel or remote control to open the
tray.
•Place the CD in the tray with the label facing
upwards.
•Press the >/]button on the front panel, or
the >/=button on the remote control, to
close the tray and start playing the disc.
For more information about playing a CD see the
next page.
For more information about playing music files
from a CDR or USB disk see Playing music from a
CDR or USB disk , page 7.

Set up your CD22 in four simple steps:





Standby O
Switches the CD22 to standby, or switches it on
from standby.
Stop/Open */å
When the disc is playing: pauses the disc.
When the disc is paused: stops the disc.
Press and hold: opens or closes the CD tray.
Play/Skip >/]
When the disc is stopped: plays the disc.
When the disc is playing: skips to the next track.
Press and hold: skips back through the tracks.

To open the tray
•Press and hold down the */åbutton on the
front panel or remote control.
The display shows:
OPEN
•Place the CD in the tray with the label facing
upwards.
•Press and hold down the */åbutton again
to close the tray (or press the >/]button
on the front panel or the >/=button on the
remote control).
The display shows:
READING
followed by the number of tracks and total time:
12 65-43
To play the disc
•Press the >/]button on the front panel, or
the >/=button on the remote control.
While a disc is playing the display shows the
current track number and the elapsed time of the
current track; for example:
07 12-34
To pause the disc
•Press the */åbutton on the front panel or
the >/=button on the remote control while
the disc is playing.
The display flashes:
You can then resume play by pressing the >/]
button on the front panel or the >/=button on
the remote control.
To stop play
•Press the */åbutton on the front panel or
the remote control while the disc is paused.
The display shows:
STOP
followed by the number of tracks and total time:
12 65-43


You can skip between tracks to locate a particular
track on the disc, or you can scan forwards or
backwards to locate a position within a track.
To skip forwards through the tracks
•Press the >/]button on the front panel, or
press the ]button on the remote control.
To skip back through the tracks
•Press and hold the >/]button on the front
panel, or press the [button on the remote
control.
The front panel display shows the track number:
1 1
•Release the button to start playing the
selected track from the beginning.
To scan through the disc
•Press the ¯or ˘button on the remote
control once to scan at 4X speed, or twice to
scan at 8X speed.
The display shows the position within the track.
•Press the >/]button on the front panel,
or the >/=button on the remote control
to start playing from the position you have
located.

This page explains how to operate your CD22, using the functions available from
either the front panel or the C23 remote control.






Before using the remote control you need to
insert the two AAA batteries supplied with the
C23.
•Gently slide open the cover on the back of
the remote control:
•Insert the two batteries, observing the
polarity printed on the bottom of battery
compartment:
•Slide back the cover until it clips into place:
Note: Replace only with alkaline
batteries type AAA, LR03, or
equivalent.
When disposing of old batteries please be
considerate to the environment.
Enter track number
Switch on/off
Play or pause the disc
Enter number >10
Increase volume of amplifier
Restart the current track,
or skip to the previous track
Repeat the track or disc
Change the displayed information
Skip to the next track
Change the
display brightness
Select between disc and USB
Shuffle tracks
Reverse scan
Forward scan
Stop the disc, or hold down
to open/close the tray
Change the sampling rate
Decrease volume of amplifier
Select CD mode
Display tracks in a folder
on CDR/USB menu
Move up on CDR/USB menu
Move down on CDR/USB menu
Select item on CDR/USB menu
Display folders on CDR/USB menu
This page explains how to
use the C23 remote control
to operate the CD22, and
how to fit the batteries into
the remote control.




This chapter explains how to use the more advanced features of the CD22, and
how to play audio files from a CDR or USB disk. These functions are accessed from
the remote control.


You can choose how the time is shown on the
front panel display, and change the brightness.
To change the time display
•Press the DISP button..
The display switches between the following four
options:
Track and elapsed time for the current track
02 03-45: .
Track and remaining time for the current track
02 01-15: .
Track and elapsed time for the entire disc
02 18-45: .
Track and remaining time for the entire disc
02 41-15: .
To change the front panel display brightness
•Press the DIM button to step through the
three levels of illumination and blank.

You can play the current track repeatedly, or
repeat the entire disc.
To repeat the current track
While the disc is playing:
•Press the REPEAT button.
The front panel shows a flashing Tafter the track
number:
1 2 T65-43:.
To repeat the entire disc
•Press the REPEAT button twice.
The front panel shows a flashing Aafter the track
number:
1 2 A65-43:.
To turn off repeat
•Press the REPEAT button again.
The Tor Ain the display will be cleared.

Shuffle playback plays the tracks on the disk in
random order.
To play the tracks in random order
While the disc is playing:
•Press the blue Bbutton.
The front panel shows a flashing Safter the track
number:
1 2 S65-43:
In shuffle mode you can pause a track by pressing
the >/=button or skip a track by pressing the ]
button.
To turn off shuffle
•Press the blue Bbutton again.
The Sin the display will be cleared.


You can play from any track by entering the track
number on the remote control.
To play from a specific track
•Specify the track number by pressing one of
the buttons 1-9.
To enter a two-digit track number press the +10
button first. For example, to enter 16 press the
+10 button followed by the 1and 6buttons.
The display shows the track number:
04 00-00:

The CD22 allows you to upsample the 44.1kHz
signal from a CD to 48kHz, 96kHz, or 192kHz,
which improves fine detail, sound stage depth and
image separation.
•Press the red Rbutton to select between
44K1, 48K, 96K, or 192K (recommended).
The display shows the current setting; for example:
F S 1 9 2 K :





You can play MP3 or WMA files on a Recordable
CD (CDR), or on a USB disk or memory stick.
To play a CDR
•Place the CDR in the tray with the label facing
upwards.
The display shows:
READING
It will then show the name of the first folder
containing MP3 files on the CDR.
[ADELE ]
To select the USB disk
•Connect the USB disk to the USB socket on
the back panel.
•Press the AUDIO button.
The display shows:
USB
It will then show the name of the first folder
containing MP3 files on the USB disk.
[ADELE ]
To select a folder
•Press the Aor Vbutton to step between the
folders.
The display shows the current folder:
[RIHANN]
Names that are too long to fit on the display will
scroll across.
•Press the >or SELECT button to display
the tracks in the selected folder.
•Press the <button to return to the list of folders.
To select a track
•Press the Aor Vbutton to step between tracks.
The display shows the current track:
FADING
•Press the >/=, >, or SELECT button to play
from the selected track.
The display shows the track number and elapsed
time for the current track:
04 00-01: .
To step through the tracks
While the tracks are playing:
•Press the [or ]button to step between
the tracks in the current folder.
To scan through a track
•Press the ¯or ˘button.
•Press the >/=button to start playing from
the position you have located.
Repeat
•Press the REPEAT button to repeat the
Track (T), Folder (F) , or All (A).
The display shows a flashing letter after the track
number:
0 4 T02-34
Shuffle
•Press the blue Bbutton to shuffle the tracks
within the entire CDR or USB disk.
The display shows a flashing Safter the track
number:
0 4 S02-45
To change the CDR or USB display
•Press the DISP button.
The display switches between the following four
options:
Track number and elapsed time for the current
track
04 03-45
Track number and track name
04 FADIN
Track number and artist name
04 RIHAN
Track number and album name
0 4 L O U D
If there are no MP3 tags the display will show the
file name.




Every component of the CD22, from the CD transport to the audio output stage,
has been designed to achieve the highest possible audio performance.

Mechanism
Asatech 8210.B01-02, Sanyo SF-P101N
D/A Converter
SRC4382 (upsampling), PCM1792A (DAC) up to
24Bit/192kHz

Analogue outputs
2VRMS, 100Ωimpedance
Digital outputs
Coaxial: SPDIF (RCA)
Optical:TOSlink
Upsampling
44.1kHz, 48kHz, 96kHz, or 192kHz.

File format
MP3 or WMA
Disk format
FAT16 or FAT32

IR input: 3.5mm
RS232
Trigger in/out: 3.5mm

Frequency response:
20Hz – 20kHz (-0.5dB)
Signal to noise ratio
20Hz – 20kHz unweighted -100 dB
THD + N: 20Hz – 20kHz <0.01%

Power Consumption
Operating 25W
Idle 23W
Standby 0.3W
Size
430 x 375 x 106 mm (WxDxH)
Weight
10.5 kg
Color
Black or titanium

These instructions help you get the best possible sound from your CD22, and give
information about configuring its advanced settings.

The phase of the AC supply can make a significant
difference to the sound.
Ensure that the live pin of the AC power cable
is connected to the left-hand pin of the power
connector, viewed from the back panel:
Live

Your Primare will start to sound best after an
initial burn-in of approximately 24 hours.
You will notice a further smaller improvement in
sound quality for at least another 3 days’ playing.

The RS232 input allows you to connect the CD22
to a controller system. For more information
please contact Primare or visit www.primare.net.
The Trigger input allows the CD22 to be switched
on by another device, such as an I32.
The Trigger output allows the CD22 to switch on
other devices.


To display the General Settings menu
•Press and hold down the Obutton until the
display shows the version number:
V1-00
NOTE:You need to keep the Obutton held
down throughout this procedure.
To set the IR input
•Press the */åbutton until the display shows:
I R
•Press the >/]button to select between
IR FRONT, to control the CD22 using a
remote control pointed at the front panel, or
IR BACK, to control it via the IR input on the
back panel.
To set the trigger input
•Press the */åbutton until the display shows:
TRIG
•Press the >/]button to select between
TRIG ON, to enable the trigger input, or
TRIG OFF, to disable it.
•Release the Obutton to return to normal
operation.



CAUTION: To reduce the risk of electrical shock
do not remove cover (or back). No user serviceable
parts inside. Refer servicing to qualified service
personnel.
WARNING: To reduce the risk of fire or electrical
shock, do not expose this apparatus to rain or
moisture.
CAUTION: In Canada and the USA, to prevent
electric shock, match the wide blade of the plug to
the wide slot in the socket and insert the plug fully
into the socket.
This product is designed and manufactured to meet
strict quality and safety standards. However, you
should be aware of the following installation and
operation precautions.
1.Take heed of warnings & instructions
You should read all the safety and operating
instructions before operating this appliance. Retain
this handbook for future reference and adhere to all
warnings in the handbook or on the appliance.
2.Water and moisture
The presence of electricity near water can be
dangerous. Do not use the appliance near water – for
example next to a bathtub, washbowl, kitchen sink, in
a wet basement or near a swimming pool, etc.
3. Object or liquid entry
Take care that objects do not fall and liquids are
not spilled into the enclosure through any openings.
Liquid-filled objects such as vases should not be
placed on the equipment.
4.Ventilation
Do not place the equipment on a bed, sofa, rug
or similar soft surface, or in an enclosed bookcase
or cabinet, since ventilation may be impeded.We
recommend a minimum distance of 50mm around
the sides and top of the appliance to provide
adequate ventilation.
5. Heat
Locate the appliance away from naked flames or
heat producing equipment such as radiators, stoves
or other appliances (including other amplifiers) that
produce heat.
6. Climate
The appliance has been designed for use in moderate
climates.
7. Racks and stands
Only use a rack or stand that is recommended for
use with audio equipment. If the equipment is on a
portable rack it should be moved with great care, to
avoid overturning the combination.
8. Cleaning
Unplug the unit from the mains supply before cleaning.
The case should normally only require a wipe with a
soft, damp, lint-free cloth. Do not use paint thinners or
other chemical solvents for cleaning.
We do not advise the use of furniture cleaning sprays
or polishes as they can cause indelible white marks if
the unit is subsequently wiped with a damp cloth.
9. Power sources
This appliance must be connected to a mains socket
outlet using the supplied power cord.To disconnect
this apparatus from power, you must disconnect the
power cord. Make sure the power cord is always easily
accessible.
Only connect the appliance to a power supply of the
type described in the operating instructions or as
marked on the appliance.
This is a Class 1 device and must be earthed.
The power switch is a single-pole switch.When the
switch is in the “Off” position, the appliance is not
completely disconnected from the main power.
10. Power-cord protection
Power supply cords should be routed so that they are
not likely to be walked on or pinched by items placed
upon or against them, paying particular attention to
cords and plugs, and the point where they exit from the
appliance.
11. Grounding
Ensure that the grounding means of the appliance is not
defeated.
12. Power lines
Locate any outdoor antenna/aerial away from power
lines.
13. Non-use periods
If the unit has a stand-by function, a small amount of
current will continue to flow into the equipment in this
mode. Unplug the power cord of the appliance from
the outlet if left unused for a long period of time.
14.Abnormal smell
If an abnormal smell or smoke is detected from the
appliance, turn the power off immediately and unplug
the unit from the wall outlet. Contact your dealer
immediately.
15. Servicing
You should not attempt to service the appliance
beyond that described in this handbook.All other
servicing should be referred to qualified service
personnel.
16. Damage requiring service
The appliance should be serviced by qualified service
personnel when:
A. the power-supply cord or the plug has been
damaged, or
B. objects have fallen, or liquid has spilled into the
appliance, or
C. the appliance has been exposed to rain, or
D. the appliance does not appear to operate normally
or exhibits a marked change in performance, or
E. the appliance has been dropped or the enclosure
damaged.


Copyright © 2011 Primare AB.
All rights reserved.
Primare AB
Renvägen 1
SE-352 45 Växjö
Sweden
http://www.primare.net
Issue: CD22/1
The information in this guide is believed to be
correct as of the date of publication. However,
our policy is one of continuous development and
so the information is subject to change without
notice, and does not represent a commitment on
the part of Primare AB.
Primare is a trademark of Primare AB.
This guide was produced by
Human-Computer Interface Ltd.
http://www.interface.co.uk
Safety compliance
This product has been designed to meet the IEC
60065 international electrical safety standard.
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
ATTENTION
RISQUE DE CHOC ELECTRIQUE NE PAS
OUVRIR
The lightning flash with an arrowhead symbol within an equilateral triangle, is intended to alert the
user to the presence of uninsulated 'dangerous voltage' within the product's enclosure that may be
of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence
of important operating and maintenance (servicing) instructions in the literature accompanying the
product.


primare.net

