Primos Killer B User manual

WARNING: Killer B™is so realistic, you need to use a blaze
orange safety flag when carrying him through the woods.
Strutting Gobbler Decoy Model No. 69021
“Killer BTM is so Realistic and Mobile that you will have
gobblers strutting in your lap!”
Components of Killer B™
Includes:
• Strutting Gobbler Decoy
• Fold-up Silk Fan
• Mobile™Series Real Fan Holder
• Fan Hardware
• Ground Breaker™Decoy Stake
• Carrying Bag with Safety Orange Flag
• 90’ Pull Line Killer B™
Strutting Gobbler Decoy
Fold-Up Silk Fan
Model No. 69047
Mobile™Series
Real Fan Holder
Model No. 69048
(for using your own fan) Carrying Bag with
Safety Orange Flag
Model No. 69046
2 Piece
Ground Breaker™
Decoy Stake
Model No. 69044
Killer B™Fan Hardware
• (4) Large fender washers are for
use on the Mobile™Series Fan Holder
and Fold-up Silk Fan.
• (2) 1/4” Wing Nuts
90’ Pull Line

Before Start
Use one of the following methods to get Killer B™to regain his shape:
• Place Killer B™under HOT water.
• Use a hair dryer to warm Killer B™.
• Place Killer B™outside on a warm sunny day.
These methods will pop him back into his original shape.
Assembly of Killer B™
Step 1 - INSTALL STAKE INTO DECOY - (See Diagram 1)
-Make sure that the stake gets installed through the stabilizer bracket during installation.
NOTE: Bottom section of stake easily installs and removes for compact carry.
Step 2 - ATTACH SILK FAN TO FAN BRACKET - (See Diagram 2)
NOTE: For added realism add real feathers to the Mobile™Series Real Fan Holder. (See Next Page)
TIP: You may trim Killer B’s™beard to the length you desire.
Top Section
of Stake
Bottom Section
of Stake with
welded side piece
Diagram 1
Front of
Decoy
Washer
Twist
Foot Peg
Stabilizer
Bracket
Wing Nut
Diagram 2
Wing Nut
Plastic Rods
Fan Bracket
Fan Screw
Diagram 3
Setting Up Killer B™For Use
Step 1 - **IMPORTANT** Install stake into ground with foot peg facing towards the front of the decoy,
toward direction of pulling line (See Diagram 3). This will keep the decoy from tipping over when pulling the
line towards you (See Diagram 4).
Step 2 - Attach 90’ Pull Line to O-Ring on front of decoy above beard (See Diagram 5).
Diagram 4 Diagram 5
O-Ring
90’ Pull
String
Correct Set-Up
Foot Peg facing toward front of decoy
Incorrect Set-Up
Foot Peg facing toward back of decoy
2 Washers

Strutting Gobbler Decoy Model No. 69021
Visit our website at primos.com.
WARNING: Killer B™is so realistic, you need to use a blaze
orange safety flag when carrying him through the woods.
Step 1
Step 2
Step 3
“Killer BTM is so Realistic and Mobile that you will have
gobblers strutting in your lap!”
(Large washers are used on the Fan Holder) - 1. Place washer onto bolt.
2. Place the Fan Holder onto the bolt. 3. Place the second washer on the
bolt. Hand tighten wing nut to desired tension.
ASSEMBLY OF MOBILE™SERIES REAL FAN HOLDER -
Your rst step to create your real fan using the Mobile™Series Fan Holder is to cut the real turkey fan where the
tail feathers meet the body. Take one of the fan feathers and pull straight back to remove the feather. There will
be some meat on the end, scrape the meat off with a knife. If the end of the quill is too long just cut it off so the
feathers will be even.
The process takes approximately 20 minutes to complete your fan. A gobblers normal tail fan has 18 feathers. The
Mobile™Series Fan Holder utilizes 16 feathers.
INSTALLING THE MOBILE™SERIES REAL FAN HOLDER ON KILLER B™-
2 Washers