Production Basics 8632 User manual

Production Basics, Inc. Massachusetts, USA 800.318.2770 617.926.8100 Fax: [phone] www.pbasics.com
ASSEMBLY MANUAL
ASSEMBLY VIDEOS AVAILABLE ON-LINE http://video.pbasics.com
1. Attach Keyboard Tray Base to Tray Extender with two (2)
8-32 bolts and nuts.
2. Attach Mouse Pad to Keyboard Tray Base using four (4)
8-32 bolts and nuts. Mouse Pad can be positioned on
right, left or center front of Tray Base. Use adjustment
slots for proper sizing.
3. Install full assembly to the back of your Flat Screen
Monitor Arm (sold seperately), through the mounting plate
and then through the monitor. The Flat Screen Monitor
Arm mounting plate should be sandwiched between the
Add-on Keyboard Tray assembly and your monitor. Use
the bolts that came with your Flat Screen Monitor Arm.
FLAT SCREEN MONITOR ARM AND
ADD-ON KEYBOARD TRAY
Item Numbers 8632, 8634 + 8633 PARTS AND HARDWARE QUANTITY
Keyboard Tray Base 1
Tray Extender 1
Mouse Pad 1
8-32 bolts 6
8-32 nuts 6
M4 x 14mm 4
Allen Wrench 1
Other Items Needed (not included)
Flat Screen Monitor Arm
ACCESSORIES
• Note: Monitor Arm and Add-on Keyboard Tray
sold separately.
Step 3
Step 2
Step 1
1603A863
1

Production Basics, Inc. Massachusetts, USA 800.318.2770 617.926.8100 Fax: [phone] www.pbasics.com
ASSEMBLY MANUAL
ASSEMBLY VIDEOS AVAILABLE ON-LINE http://video.pbasics.com
1. Before assembling the keyboard support with the
enclosed instructions, attach mounting plate to adapter
using button head bolts and nuts provided. See diagram
at left.
2. Insert a Basic Bolt into the corner holes of the adapter
and secure with a Basic Nut, turning only one revolution.
See diagram at left. For RTW Tables, proceed to step
4a.
3. Insert nuts attached to adapter into Worksurface Support
Rails on your workstation, as shown. Turn Basic Bolt 90
degrees clockwise to grip. Tighten the bolts.
4. Proceed with enclosed instructions for your keyboard.
a. For RTW Tables, insert wood screws through holes
on tabs to attach Keyboard Support to underside of
worksurface.
5. Secure the wrist support by inserting plastic screws from
the bottom and tighten.
ADJUSTABLE KEYBOARD SUPPORT
Item Numbers 8680 PARTS AND HARDWARE QUANTITY
Adapter Plate 1
Mounting Plate 1
8/32 Button head bolt 6
Nuts 6
Washers 6
Wood screws 4
Basic Bolts 4
Basic Nuts 4
7/32 Allen Wrench 1
3/32 Allen Wrench 1
See Step 1
Adapter Plate
See Step 4a for RTW Tables,
Easy-Lift 4-Post
See Step 2 for C-Leg,
Easy-Lift Dual-Leg
Mounting Plate
Adapter Plate
1603A863
2

Need Help? Call Assembly Support at 800.318.2770
1. Using three (3) 8-32 x 3/8” nuts and bolts, assemble
Upper and Lower Side Brackets as shown for right and left
brackets, according to your style of workstation.Set aside
until step 4.
a. For C-Leg & Easy-Lift Dual-Leg workstations,
assemble brackets so that the Upper and Lower Side
Brackets are flush against each other.
b. For RTW, Easy-Lift 4-Post or PedSys workstations,
assemble brackets so that the Lower Side Brackets
extend below the Upper Side Brackets.
2. Choose right or left side for mouse tray. Using two (2) 8-32
x 3/8” bolts, hex nuts and washers, install the mouse pad
bracket onto the keyboard tray under the back lip of the
wrist rest. Slide the tray onto the bracket and repeat for the
rear mouse pad bracket with tray in place. The mouse tray
should slide freely. A lip on the tray acts as a stop.
3. Attach adhesive backed cable clip to back of keyboard tray.
These hold your mouse and keyboard wires in place.
4. Slide keyboard onto left and right side brackets as shown.
5. For C-Leg and Easy-Lift workstations insert a Basic Bolt
through the two (2) large holes on top of each bracket from
step 1. Secure with a Basic Nut. Turn one revolution.
a. For RTW, use wood screws to attach to underside of
worksurface. Go to Step 6.
6. Position the keyboard under the workstation. Insert the
Basic Nuts attached to the bracket into the Worksurface
Support Rail and tighten the bolts.
PARTS AND HARDWARE QUANTITY
Upper Side Bracket 2
Lower Side Bracket 2
Basic Bolts 4
Basic Nuts 4
Keyboard Drawer 1
Cable Clip 2
Mouse Pad Bracket 2
Mouse Tray 1
8-32 Bolts 10
8-32 Nuts 10
Wood Screws 6
3/32 Allen Wrench 1
Other Items Needed (not included)
Phillips head drill
KEYBOARD DRAWER
item Number 8681
Upper side Bracket- C-leg/Easy-Lift Dual Leg, left side
Lower Side Bracket C-Leg/EasyLift Dual Leg, right side
Upper side Bracket- RTW/Easy-Lift 4-Post, left side
Lower Side Bracket RTW/Easy-Lift 4-Post, PedSys, left side
Cable Clip
Mouse Tray
Completed Keyboard Drawer for
C-Leg/Easy Lift Dual Leg
See Step 4a for RTW Table,
Easy-Lift 4-post, PedSys
Wrist Rest
Rear Mouse Pad Bracket
Mouse Pad Bracket
Step 1a
Step 1b
Steps 2-3
Steps 4-6
ASSEMBLY VIDEOS AVAILABLE ON-LINE http://video.pbasics.com
1603A863
3