PROformance Hoops PROforce Series User manual

PROforce Series
ADJUSTABLE HEIGHT
GOAL SYSTEM
PROforce
672/660/554

2 www.proformancehoops.com 1-888-353-4667
THANK YOU!
Thank you and congratulations for purchasing a Proformance Hoops Goal - the
finest basketball goal system on the market today! You will discover that
Proformance Hoops is unsurpassed in product innovation, quality and integrity in
the basketball equipment industry. We are focused on designing and engineering
products that meet and exceed the expectations of demanding players and
withstand today’s toughest playing environments.
LAY OUT PLAYING COURT
Consider the following to determine where to install the basketball goal:
Whether the goal is to be installed into a landscaped area next to the playing surface or
into a hard-surfaced area.
Backboard size and its extension distance from the structures.
If court markings are to be used.
Amount of playing surface desired beneath the goal.
Other functions of playing surface (such as driveway, tennis court, etc.)
There must be at least 18” clearance behind the back of the Goal Post to allow room to
operate the goal height adjusting crank.
When the rim is set to the regulation height of 10 ft. the distance from the face of the
backboard to the front of the Goal Post is, depending upon the PROforce (PF) or
PROview (PV) model, shown in the figure below.

1-888-353-4667 www.proformancehoops.com 3
SAFETY INSTRUCTIONS
GOAL ASSEMBLY
IMPORTANT: Concrete must cure a minimum of 72 hours before installing goal.
IMPORTANT: Safe assembly of the goal requires two to three people in good physical
condition and capable of lifting 80-100 lbs (36-45 kg) each.
IMPORTANT: Locate and familiarize yourself with all the parts of the goal before
beginning assembly.
REQUIRED TOOLS AND MATERIALS:
Level
Rubber Mallet
12' Tape Measure
Phillips Screwdriver
Ratchet
Sockets or wrenches:
15mm (9/16")
19mm (3/4")
24mm (15/16")
27mm (1-1/16")
Failure to follow these safety instructions may result in serious injury or death and/or
property damage.
 Do not install or use this product unless the instructions within this manual have been carefully
read and understood.
 Consult Proformance Hoops if you do not understand the instructions in this manual or need
additional information
 Know what’s below ground. “Call before you dig” the hole for the ground anchor. For the US
the number is 811.
 If using a ladder during assembly, use extreme caution. Two or three people are recommended
for safe installation and assembly.
 Installation and assembly of this product will require lifting and bending that may result in
injury to anyone not accustomed to this type of activity.
 Ensure there are no overhead power lines within a 20 ft. (7m) radius of the goal location.
 Climate, corrosion or misuse could result in system failure.
 DO NOT HANG on the rim or any part of the goal system. This includes the backboard, support
braces and net.
 During play, especially when performing dunking activities, players should keep their faces
away from the backboard, rim and net. Serious injury could result if teeth or face come in
contact with the backboard, rim or net. Do not wear jewelry or other loose objects that could
become entangled with the net.
 Twice yearly, check the goal system for loose hardware, excessive wear and signs of corrosion.
Repair the system before use.
 Never play on damaged equipment.

PARTS LIST
4
U1
U2
U4
U4
U4
U6
U3
U3
U5
A
B
C
E
F
F
G
H
J
K
R1
R2 R3
1
11
1
1
1
2
3
3
4
5
6
6
7
7
8
8
8
8
8
8
8
8
8
8
88
9
10
10
10
10
10
10
IT EM QTY DESCR IPTIO N
A1MainPost
B1Actuator
C 1 Actuator pl astic p ipe
D 1 Pole padding (optional)
E 1 Lower Extension Arm
F 2 Upper Extension Arm
G 1 Backboard
H 1 Rim Height Sticker
J1Crank
K 1 Flex Rim (Separate pack)
U1 1 Anchor Template
U2 4 16mm Anc hor J-bol ts
U3 8 Thick washer for J-bolts
U4 12 Hex nut M16
U5 4 Anchor Rebar 36" L
U6 4 Lock Washer M16
R1 4 Car ria ge B olt M1 0x5 0mm
R2 4 Washer M10
R3 4 Fla nge n ut M10
HARDWARE LIST
110
Nylon Washer M12
(2pcs may be factory-assembled).
2 1 Hex Bol t M 16 x30 5m m
3 2 Hex Bolt M12x300mm
4 1 Hex Bolt M12x210mm
5 1 Hex Bolt M12x120mm
6 2 Hex Bol t M 12 x35 mm
7 2 Washer forM16 Bolt
8 12 Wa she r for M1 2 Bolt
91LockNutM16
10 6 Lock Nut M12
UNDERGROUND PARTS
PARTS LIST
RIM HARDWARE

! !
WARNING
A hammer or mallet may be needed during assembly.
Figure1
Figure 3 Figure 4
Figure2
U6
U4
U3
U4assembled
U1
U2
A
U3
Playing
Court
Front side
Back
side
Place the Pole on the Anchor system.
Slide one Thick washer M16 (U3) over
each J-bolt (U2). Lift the Pole (A) onto
Anchor system, secure with one thick
washer (U3), one Lock washer M16 (U6)
and one Hex nut (U4) for each J-bolt.
See Figure 1.
If the Main Post (A) is not exactly
vertical, adjust the 16mm J-Bolt Hex
Nuts (U4) located under the Post base
(A). Tighten all of the Hex Nuts (U4)
Above Post base when Main Post (A) is
vertical.
NOTE: Face the Main Post (A) with Actuator
Bracket facing away from playing court (as
shown in ).FIGURE 2
1.
Attach Lower Extension arm (E) to
Pole (A), Figure 3as shown in .
Secure it with one Hex bolt M12x300
(#3), two Flat washers M12 (#8), two
Plastic Washers M12 (#1), one Lock
nut M12 10 See(# ). Figure 7.
Note make sure Plastic washers go:
between Lower Extension and Pole.
2.
A
E3
8
1
8
10
Slide Plastic sleeve
over Actuator
A
C
C
2
7
8
8
5
1
10
7
9
B
B
E
J
5

6
Figure 5
Attach Upper Extension arm (F)to Pole
(A),
using one Hex bolt M12x210 (#4), two
Flat washers M12 (#8), two Plastic
washers M12 (#1), and one Lock nut
M12 (#10). See .Figure 5
Note: The plastic washer should be placed
between Upper extension arm (F) and Pole
pivot tube (A).
6.
7. Attach Backboard (G) to Lower Extension arm (E).
Turn crank to lower support frame (E) until against
safety stop.
With 3 capable adults, raise the Backboard assembly
up and connect Lower Extension arm (E) to the
Backboard Bracket using one Hex bolt M12x300 (#3),
2 washers M12 (#8), 2 Plastic washers M12 (#1), and
1 Lock nut M12 (#10).
Tighten this bolt snugly. See .Figure 5
Note:
The plastic washer goes between backboard bracket (G)
and Lower extension arm (E).
Attach Backboard (G) to Upper
Extension arm (F).
Connect Upper board arm (F) to the
Backboard edge using 2 Hex bolts M12x35
(#6), 4 Flat washers M12 (#8), 2 Plastic
washers M12 (#1), and two Lock nuts M12
(#10).
Tighten the two bolts and nuts snugly.
See Figure 5.
8.
Nylon washer #1 may
be factory installed
Attached Actuator (B) to Lower extension
Arm (F).
Slide Actuator plastic sleeve (C) over top of
Actuator (B), align the hole in the Plastic sleeve
with the hole in the Actuator,
See in previous page.Figure 4
Hold the Actuator assembly, align the hole in the
Plastic sleeve (C) with the Rear hole of Lower
extension Arm (F), attach them together with
one Hex bolt M16x305 (#2), two Flat washers
M16 (#7), and one Lock nut M16 (#9).
Attached Actuator (B) to Actuator mounting
plate (E).
See in previous page.Figure 4
Move Actuator between two Mounting plate (E),
secure them together with one Hex bolt
M12x120 (#5), two Flat washer M12 (#8), two
Plastic washers M12 (#1), and one Lock nut
(#9).
Do not over tighten this bolt.
Note make sure Plastic washers go between:
Mounting plate (E) and Actuator (B). It prevents
painted parts from being scratched.
Attach Crank (J) to the bottom of Actuator with
supplied Lock pin.
5.
4.
A
E
F
F
G
4
8
8
10
10
10
10
1
1
1
1
6
6
3
8
8
8
8
8
8

7
Apply Rim Height Sticker
Use a tape measure to crank rim
up to exactly 10' from playing
surface. Make a line mark on the
Actuator (B) against bottom
edge of Actuator Sleeve (C).
Crank the rim all the way down to
the extreme end. Peel and apply
Rim Height sticker to outside of
Actuator (B) lining up the mark
with the 10' mark on the Rim Height
Sticker. The Sticker may need
to be trimmed to clear the
Actuator Sleeve.
See Detail A.
10ft
Rim Height
sticker
Actuator sleeve (C)
Attach Goal (K) to Backboard (G).
Remove the Rim box cover, put Goal
against Rim pad (Pre-installed), secure it
with 4 Carriage bolts M10x50 (#R1), 4 Flat
washers M10 (#R2), 4 Flange nuts M10
(#R3) See .Figure 6
Tighten all four bolts and nuts.
Put Rim box cover back and secure it with
removed screws.
9.
10.
R1 R2 R3
K
G
Figure 6
Figure 7
NOTE: Use a level to make sure rim is level side to side
before tightening nuts.

BUYER AGREES THAT ALL PRODUCTS SOLD BY PROformance Hoops CARRY THE FOLLOWING WARRANTY
Subject to proper installation, and normal intended use, all structural components of PROview®Series, PROforce Series, Pro Series
Extreme Series, and Wall Mount Basketball Systems are warranted to the original owner to be free of defects in materials and
workmanship for the duration of ownership by the original retail purchaser, subject to thelimitations below. PROformance Hoops shall
have the right to require the purchaser to deliver the allegedly defective products to PROformance Hoops fortesting, repair, or
replacement.
PROformance Hoops shall not be responsible for any expense associated with the replacement or removal of the product from its
application for such delivery. Freight and handling charges may apply to covered warranty parts. Modification of any product by the
customer, unless approved by PROformance Hoops, will void all warranty. Where listed as “LIMITED”, the warranties shall cover
damage of failure that occurs during the course of NORMAL or INTENDED USE of the product. Normal or intended use shall be
described as activity that is necessary for the participation inthesport for which the equipment is damaged. NOT COVERED is
damaged caused by deliberate hanging, multiple player hanging, vandalism, non-basketball activities, or any other activity that could be
regarded as abusive.
Backboard Edge Padding: Three (3) year limited;
Indoor Backboard Edge Padding: Five (5) year limited
Custom-Fit Pole Padding: 3 year limited;
Wrap-Around Pole Padding: one year limited.
NOT COVERED BY THIS WARRANTY
•Use in non-residential applications of glass backboards.
•Use in non-residential applications of traditional complete systems.
•Any products subjected to abuse, negligence, improper installation, vandalism, acts of God, alteration of product or any other
events beyond the control of PROformance Hoops.
•Paint or rusted parts.
•Deterioration of product due to time and wear.
Normal deterioration of products due to atmospheric conditions, weather, rust, wear and tear (including paint), or other causes that do
not affect functional use are not covered by PROformance Hoops warranties. All warranties are valid only when product is used in the
intended application, and when installed according to PROformance Hoops instructions. Warranty will be void if maintenance
instructions in the Owner’s Manual are not followed, including jack lubrication on a bi-yearly basis. If you did not receive an Owner’s
Manual, please contact ProformanceHoops.com and one will be sent to you.
WARRANTY CLAIMS: All returns must be arranged through the local dealer if available. Warranties do not cover dealer service
charges, labor charges, freight or travel expense associated with replacement, repair, or removal of warranty item. A warranty claim
form must be completed, and photos submitted for any item you wish to claim under warranty. If the purchase was not made through a
dealer, this form is available on proformance.com. In response to your claim, you will receive a confirmation as well as a notice stating
whether PROformance Hoops needs your warranty item returned. PROformance Hoops will notify you if we determine that the item
cannot be claimed under warranty. PROformance Hoops is not responsible for any charges for labor to install or repair
defective product prior authorization. PROformance Hoops will determine the most economical method to either repair or
replace product before any work is to commence.
TO THE MAXIMUM EXTENT PERMITTED BY LAW, THIS WARRANTY AND THE REMEDIES SET FORTH HEREIN ARE
EXCLUSIVE AND EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WARRANTIES
OR MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IF PROFORMANCE HOOPS CANNOT DISCLAIM OR
EXCLUDE IMPLIED WARRANTIES UNDER APPLICABLE LAW, THEN TO THE EXTENT POSSIBLE ANY CLAIMS UNDER SUCH
IMPLIED WARRANTIES SHALL EXPIRE OR EXPIRATION OR THE APPLICABLE WARRANTY PERIOD. SOME STATES DO NOT
ALLOW LIMITATIONS ON HOW LONG IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
PROFORMANCE HOOPS DOES NOT ASSUME OR AUTHORIZE ANY PERSON TO ASSUME FOR US, ANY OTHER LIABILITY IN
CONNECTION WITH THE SALE OF OUR PRODUCTS.
TO THE MAXIMUM EXTENT PERMITTED BY LAW, PROFORMANCE HOOPS ASSUMES NO RESPONSIBILITY FOR
INCIDENTAL OR CONSEQUENTIAL DAMAGES, WHICH MAY ARISE FROM THE PURCHASERS OR USE OF OUR EQUIPMENT.
SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATIONS OF INCIDENTAL OR CONSEQUENTIAL DAMAGE, SO THE
ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.
IF ANY PROVISION OF THIS WARRANTY IS INVALID, VOID OR UNENFORCEABLE IN ANY INSTANCE OR RESPECT, THE
UNENFORCEABLE PROVISION WILL BE SEVERED AND REFORMED TO EFFECT THE INTENT OF THIS LIMITED WARRANTY
TO THE MAXIMUM EXTENT POSSIBLE, AND THE REMAINING PROVISIONS SHALL CONTINUE IN FULL FORCE AND EFFECT
AND SHALL BE ENFORCED TO THE FULL EXTENT PERMITTED BY LAW.
This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state
2.28.20
Proformancehoops.com -----1-888-353-HOOP (4667)
PROformance Hoops Warranty
(PROview® Series, PROforce Series, Pro Series, Extreme Series and Wall Mounts)