PROGRESSIVE DESK DM-04-2L User manual

Screen Size
17"-32"
Cable
Management
Laptop
10"-15.6"
9kg/19.8lbs
MONITOR
RATED
4kg/8.8lbs
LAPTOP
RATED
V 1.1
DM-04-2L
User Manual
Scan for more information

..................................................................................3
Parts List .........................................................................................4
Assembly&Installation ...................................................................5
P a g e | 2
Table of Contents
Specifications
Have any queries? Our expert engineers are here to help!
[email protected] progressivedesk.com
1-800-828-9414

Specifications
Monitor Compatibility
Monitor Weight Capacity
Laptop Compatibility
Laptop Weight Capacity
Product Weight
Desk Thickness - Clamp
Desk Thickness - Grommet
Grommet Hole Diameter
Cable Management
VESA Compatibility
Base Joint Rotation
Elbow Joint Rotation
Neck Joint Rotation
VESA Mount Rotation
Tilt
17" to 32"
19.8 lbs
10" to 15.6"
8.8 lbs.
10.5 lbs.
0.4" to 3.3"
0.4" to 1.5"
0.4" to 3.2"
Cable Cover, Cable Hooks
100mm x 100mm and 75mm x 75mm
±90°
±90°
±90°
±180°
±45°
Height Adjustment
Clamp Mount
Up to 15.25"
Included
Grommet Mount
Detachable VESA
Included
Included
P a g e | 3
1.5
"
6.9
"
9.5
"-16.5"
6.4
"
2.6
"
16.0 "
3.9 "
0.4 "-3.3"
0.4 "-1.5"

Parts List
P a g e | 4
No. Part Qty.
Base Plate
A1
Clamp
A4 1
Arms
A5 2
1
Mounting Pole
A2 1
Bracket
A3 1
Cable Cover
A7 1
VESA Plate
A8 2
Cable Hooks
A6 4
Adjustable Clamp
A10 2
Clip
A11 2
Laptop Tray
A9 1
M5x16 Screw
B1 1
M10x20 Screw
B2 1
B3 4
M6x10 Screws
M4x8 Screws
B4 4
B5 1
B6 1
4mm Hex Key
B7 1
6mm Hex Key
Philips Head Screwdriver
No. Part Qty. No. Part Qty.
M-C 4
Washers
M4x12 Screws
M-A 4
M5x12 Screws
M-B 4

Assembly & Installation
P a g e | 5
Step 1: Attach the Base Plate
Step 2: Choose Installation Method (Clamp or Grommet)
Attach the Base Plate (A1) to the Mounting Pole (A2) using the M5x16 Screw (B1). Ensure the largest center holes on each
part are aligned. Tighten with Philips Head Screwdriver (B7).
Option 1: Clamp – Mount to Side of Desk (Page 6)
Requirements: Desk Thickness 0.4” to 3.3”
Option 2: Grommet – Install into Grommet Hole or Drilled Hole (Page 8)
Requirements: Desk Thickness 0.4” to 1.5”, Desk Hole Diameter 0.4” to 3.2”
Desk Hole Diameter
Desk
Thickness
Option 1: Clamp Option 2: Grommet

Assembly & Installation
Option 1: Clamp – Mount to Side of Desk
Step 2A: Align Bracket (A3) with the studs on the Base Plate (A1) and attach using the M10x20 Screw (B2). Tighten with
6mm Hex Key (B6).
Step 2B: Insert 2x M6x10 Screws (B3) into the Bracket (A3) using the 4mm Hex Key (B5). DO NOT TIGHTEN the screws.
Leave at least a 3/16" gap for Step 2D.
P a g e | 6

Assembly & Installation
Step 2C: For tabletop thickness 0.4" to 1.75" skip to Step 2D.
For tabletop thickness 1.75" to 3.3", unscrew the preinstalled screw on the Clamp (A4) using the Philips Head Screwdriver
(B7). Separate the clamp components, flip the small bracket, and put the parts back together. Tighten the screw using the
Philips Head Screwdriver (B7).
Step 2D: Hook on Clamp (A4) to the loose screws from Step 2B. Tighten the M6x10 Screws (B3) using the 4mm Hex Key
(B5).
Step 2E: Place the assembly on your desired tabletop location and secure by tightening the clamp knob.
P a g e | 7

Assembly & Installation
P a g e | 8
Option 2: Grommet – Install into Grommet Hole or Drilled Hole
Step 2A: Separate the components from Clamp (A4) by using the Philips Head Screwdriver (B7). Put the mounting plate
onto the threaded knob screw.
Step 2B (Optional): For installations on a tabletop WITHOUT a grommet hole or predrilled hole, use a drill with a 3/8” drill
bit.
Step 2C: Insert the threaded knob screw and plate into the bottom side of the tabletop. Align with the hole on the base
plate assembly. Tighten the knob to secure the monitor stand to the tabletop.

Assembly & Installation
P a g e | 9
Step 3: Position the VESA Mount
Step 3A: Slide the VESA Plate (A8) onto the VESA mount of the Arm (A5).
Step 3B: Rotate the VESA mount 90 degrees so that the connector is facing up as seen below.
Step 3C: Remove the VESA Plate (A8) from the Arm (A5).
Step 3D: Repeat Steps 3A-3C for the other Arm (A5), this time turning the connector 90 degrees the other way so that they
are both facing up.

Assembly & Installation
P a g e | 10
Step 4: Install the Arm
Install the Arms (A5) to the Mounting Pole (A2) at the desired heights. Tighten using the 6mm Hex Key (B6) to
secure each arm. Recommended to first install the arm which will support the laptop as it’s often lower down compared to
monitors.
Step 5: Attach the Cable Management Hooks and Cover
Step 5A: Attach 2x Cable Hooks (A6) to each Arm (A5).
Step 5B: Attach the Cable Cover (A7) to the Mounting Pole (A2).

Assembly & Installation
P a g e | 11
Step 6: Install VESA Plate to the Monitor
Install a VESA Plate (A8) to your desired VESA compatible monitor. Align the VESA Plate (A8) with the top of the
monitor. Ensure the flange is facing out and towards the top of the monitor as seen below. Use Washers (M-C) and
compatible screws (M-A or M-B) with the monitor.
DO NOT OVERTIGHTEN! Secure the parts using the Philips Head Screwdriver (B7).
Step 7: Slide the VESA Plate onto the Desired Arm
Slide the VESA Plate (A8) onto the desired Arm (A5) VESA mount. Secure the monitor using 1x M6x10 Screw (B3) and
tighten with 4mm Hex Key (B5).

Assembly & Installation
P a g e | 12
Step 8: Assemble Laptop Tray
Step 8A: Align the Adjustable Clamps (A10) behind the Laptop Tray (A9), and secure using the Clips (A11) as seen below.
Step 8B: Secure the VESA Plate (A8) to the back of the Laptop Tray (A9) using 4x M4x8 Screws (B4) and tightening
with the Philips Head Screwdriver (B7). Ensure the flange is facing out and towards the top of the laptop tray as seen
below.
Step 9: Slide the Laptop Tray onto the Arm
Slide the VESA Plate (A8) onto the Arm (A5) VESA mount. Secure the VESA Plate (A8) using 1x M6x10 Screw (B3) and
tighten with 4mm Hex Key (B5).

Assembly & Installation
P a g e | 13
Step 10: Adjust the Laptop Tray to Fit Laptop
Move the Adjustable Clamps (A10) to fit your laptop. Lock the sliders in place by using the levers on the back of the
Adjustable Clamps.
Step 11: Cable Management
Attach the monitor cables and route them through the installed cable management hooks and cover.
Step 12: Monitor Arm Range
Caution: DO NOT use the display beyond the arrow range to avoid tipping.

Assembly & Installation
P a g e | 14
Have any queries? Our expert engineers are here to help!
[email protected] progressivedesk.com
1-800-828-9414
Step 13: Adjustability
Using the 6mm Hex Key (B6) to adjust the up and down tilt of the Laptop Tray and monitor. Note: If the display does not
stop at your desired position, tighten the screws.
Step 14: Optional Hex Key Storage
Store the Hex Keys in the Cable Cover (A7) for future adjustments.