GABOR Mainmast DMS-200 User manual

User Manual
DMS-200 / MAINMAST SINGLE DISPLAY
DESKTOP MONITOR STAND
for 17 to 32 in. Screens
Mainstay DMS-200

2
Gabor’s sturdy Mainmast Single Display Desktop Monitor Stand
is a space and clutter saver for desks and workstations at
home and in the office. This freestanding desk accessory can
hold a 17- to 32-inch monitor weighing up to 15.4 pounds, and it
allows you to adjust the height, swivel, and tilt for the perfect
viewing angle. Standard VESA 100 × 100 and 75 × 75 patterns
are compatible with most monitors, and the VESA plates
rotate for both landscape or portrait orientation.
Thank you for choosing Gabor.
Mainstay DMS-200

3
• Please read and follow the instructions, and keep this manual in a
safe place.
• To avoid damage to this product, be careful not to overtighten or
improperly thread any of the threaded fittings.
• Clean this product with only a soft, dry cloth.
• Mounting surfaces should be sturdy and flat. Do not install this
product on a weak, uneven surface.
• Do not install this product on an unsteady structure or one that is
prone to vibration, has a chance of being impacted, or is susceptible
to other movements. Reinforce the structure as necessary before
installing this product.
• Make sure everything is secure before proceeding to the next step.
• Do not exceed the maximum load capacity.
• Make sure that this product is intact and that there are no missing
parts.
• If this product is missing hardware or there are defective parts, visit
www.madebygabor.com or call Customer Service at 212-594-2353.
• If you have safety concerns about installing this product, contact a
qualified professional or installation contractor.
• All images are for illustrative purposes only.
Safety Warnings

4
Monitor display size
17 to 32 in. (43.2 to 81.3 cm)
Maximum monitor weight
15.4 lb. (7 kg)
VESA standards
75 × 75 mm
100 × 100 mm
Monitor rotation
±180°
Monitor tilt
±15°
Column rotation
±40°
Monitor height adjustment range
5.9 in. (15 cm)
Column height adjustment
10.4 to 16.3 in. (26.5 to 41.5 cm)
Weight (without monitor)
6.7 lb. (3 kg)
Package Weight
8.2 lb. (3.7 kg)
Package Dimensions (W × L × H)
17.1 × 10.8 × 4.4 in. (43.5 × 27.5 × 11.2 cm)
Product Specifications
570 mm
460 mm
75 mm
100 mm
117 mm
115 mm
100 mm
75 mm
240 mm
200 mm
265 mm - 415 mm
Mainstay DMS-200
±40°
±180°

5
Overview
Monitor arm hook
Cable channel
Column
Height lock
Tilt tension
screws
Lever
back
Bracket
support
Base
Lever front
Mounting
bracket
Mainstay DMS-200
VESA
plate

6
Parts Included
M-A 4X
M4 × 12 mm screws
M-B 4X
M5 × 12 mm screws
M-C 4X
D5 washer
B C 1X1X D E 1X1X
1X4X
F G 2X H I
1X
A1X
MainmastDMS-202
M4 × 8 mm screwM4 × 6 mm screw
1X1X
J K 1X L
5 mm hex keyM6 × 20 mm screw
Hex boltBracket supportColumn
Lever frontLever backMounting bracketBase
6 mm hex key

Assembling the Base
7
Fit the column (A)
into the base (B).
Screw the hex bolts
(G) into the holes in
the bottom of the
base using the 6
mm hex key (L).
Attaching the Lever
1. Attach the lever back
(D) to the height lock
with the four M4×6
screws (H). Use the
screwdriver end of the
5 mm hex key (K) to
tighten the screws
until secure.
2. Slide the lever front
(E) up onto the lever
back (D) so it locks in
place.
G
L
B
A
H
K
D
E
3. Secure the lever front to the
lever back with the M4×8 screw
(I). Tighten it with the Phillips
end of the 5 mm hex key (K).
I
K
A
1X
B
1X
MainmastDMS-202
K LD
1X
E
1X
G
2X
H
4X
I
1X

C
Inserting the VESA Mount
onto the Column
8
1. Hang the mounting bracket on the hooks that
extend from the front of the column.
F
J
K
2. Attach the bracket support (F)
under the mounting bracket,
and secure it with the M6×20
screw (J). Use the Phillips end
of the 5 mm hex key (K) to
tighten until secure.
J
1X
C
1X
F
1X
K

K
9
Mounting the Monitor M-C
4X
M-A
4X
M-B
4X
K
VESA
PATTERNS
75
100
75 100
3 mm
100 × 100 VESA Pattern
1. Slide M-C washers onto two
screws, and thread the screws
into your monitor’s top two
VESA holes. Leave about 3
mm between the washers and
the monitor.
2. Hang the monitor on the VESA
plate’s two top notches with
the two installed mounting
screws.
Important! The washer should be
between the screwhead and the
VESA plate.
75 × 75 VESA Pattern
1. Thread two screws into your
monitor’s top two VESA
holes. Leave about 3 mm
between the screws and the
monitor.
2. Hang the monitor on the
VESA plate’s two keyholes
with the two installed
mounting screws.
Important!
Do not use washers for
the top screws on the 75×75 VESA
pattern.
3. Slide M-C washers onto two screws, and thread the screws into the bottom two VESA holes.
4. Use the 5 mm hex key (K) to tighten all four screws until snug. Do not overtighten.
Before you attach the VESA plate, hand thread one of the M-A or M-B screws to determine
which one fits your monitor. Make sure the screw is also not too long or too short. If the
screw is too long, it may damage the display. If it’s too short, it may not hold it.

10
After the monitor is installed, keep your cables neat
and organized by running them through the cable
channel in the column.
Cable Organization Adjusting the Monitor Height
Important! When adjusting
monitor height, support the
bottom of the monitor with
one hand. The other hand will
support the monitor from
above and operate the lever.
This will prevent the monitor
from accidentally rising too
quickly or tipping over.
1. With the monitor
attached, press the
lever towards the
monitor.
2. Adjust the monitor to
the desired height, and
release the lever.
Tilt
To adjust the viewing angle,
tilt the monitor up and
down by 15°.
You may need to increase
the tilt tension for larger
and heavier monitors.
Tighten the tilt tension
screws by turning them
clockwise with hex key (K).
For smaller and lighter
monitors, decrease the
tilt tension by turning the
tilt tension screws
counterclockwise.
Rotation
To change the orientation of a
monitor from landscape to
portrait, turn the monitor while
it’s attached to the VESA plate.
MainmastDMS-202
Mainmast DMS-202
Swivel
For optimum monitor position, the
column swivels 40° to the left and right.
Hold the monitor on both sides to
position it at the preferred angle.

MainstayDMS-200
After the monitor is installed, keep your cables neat
and organized by running them through the cable
channel in the column.
Monitor Tilt, Rotation, and Swivel
11
Important! When adjusting
monitor height, support the
bottom of the monitor with
one hand. The other hand will
support the monitor from
above and operate the lever.
This will prevent the monitor
from accidentally rising too
quickly or tipping over.
1. With the monitor
attached, press the
lever towards the
monitor.
2. Adjust the monitor to
the desired height, and
release the lever.
Tilt
To adjust the viewing angle,
tilt the monitor up and
down by 15°.
You may need to increase
the tilt tension for larger
and heavier monitors.
Tighten the tilt tension
screws by turning them
clockwise with hex key (K).
For smaller and lighter
monitors, decrease the
tilt tension by turning the
tilt tension screws
counterclockwise.
Rotation
To change the orientation of a
monitor from landscape to
portrait, turn the monitor while
it’s attached to the VESA plate.
K
Swivel
For optimum monitor position, the
column swivels 40° to the left and right.
Hold the monitor on both sides to
position it at the preferred angle.

Three-Year Limited Warranty
This Gabor product is warranted to the original purchaser to be free from defects in materials and workmanship under normal consumer use for a period
of three (3) years from the original purchase date or thirty (30) days after replacement, whichever occurs later. The warranty provider’s responsibility with
respect to this limited warranty shall be limited solely to repair or replacement, at the provider’s discretion, of any product that fails during normal use of
this product in its intended manner and in its intended environment. Inoperability of the product or part(s) shall be determined by the warranty provider.
If the product has been discontinued, the warranty provider reserves the right to replace it with a model of equivalent quality and function.
This warranty does not cover damage or defect caused by misuse, neglect, accident, alteration, abuse, improper installation or maintenance. EXCEPT AS
PROVIDED HEREIN, THE WARRANTY PROVIDER MAKES NEITHER ANY EXPRESS WARRANTIES NOR ANY IMPLIED WARRANTIES, INCLUDING BUT NOT
LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. This warranty provides you with specific legal
rights, and you may also have additional rights that vary from state to state.
To obtain warranty coverage, contact the Gabor Customer Service Department to obtain a return merchandise authorization (“RMA”) number, and return
the defective product to Gabor along with the RMA number and proof of purchase. Shipment of the defective product is at the purchaser’s own risk and
expense.
For more information or to arrange service, visit www.madebygabor.com or call Customer Service at 212-594-2353.
Product warranty provided by the Gradus Group.
www.gradusgroup.com
Gabor is a registered trademark of the Gradus Group. © 2021 Gradus Group LLC. All Rights Reserved.
GG2