Progressive Turf Equipment TD65 User manual

Operator’s Manual and Parts List
TD65
Rotary Finish Mowers
Serial No. 13651442 and up
TD65-2
Rotary Finish Mowers
Serial No. 1365-21376 and up
PROGRESSIVE TURF EQUIPMENT INC.
137 WEST WILLIAM STREET
SEAFORTH, ONTARIO
CANADA N0K 1WO
TOLL FREE: 800 668-8873
ISSUE DATE: March 2018
P.N.120512 www.progressiveturfequip.com

TD65 Operator’s Manual
TABLE OF CONTENTS PAGE
INTRODUCTION..............................................................................................................................2
FOREWORD ....................................................................................................................................2
ITEMS INCLUDED WITH TD65 MOWER...............................................................................................................3
SERIAL NUMBER LOCATION...............................................................................................................................3
REPLACEMENT PARTS INFORMATION ..............................................................................................................3
UNAUTHORIZED MODIFICATION.........................................................................................................................3
MISUSE OF EQUIPMENT......................................................................................................................................4
NOTIFICATION OF UNAUTHORIZED MODIFICATION OR MISUSE ....................................................................4
PRODUCT DESIGN...............................................................................................................................................4
SPECIFICATIONS ...........................................................................................................................5
COMPONENT IDENTIFICATION ....................................................................................................6
SAFETY RULES..............................................................................................................................7
SAFETY ALERT SYMBOL .....................................................................................................................................7
HAZARD SERIOUSNESS LEVEL..........................................................................................................................7
GENERAL SAFETY PRECAUTIONS.....................................................................................................................8
POWER UNIT SAFETY..........................................................................................................................................8
OPERATING EQUIPMENT SAFELY......................................................................................................................9
MAINTENANCE SAFETY PRECAUTIONS ..........................................................................................................10
SAFETY DECALS .........................................................................................................................13
DECAL LOCATIONS............................................................................................................................................13
DECAL LISTING..................................................................................................................................................14
ASSEMBLY INSTRUCTIONS .......................................................................................................16
SET-UP................................................................................................................................................................16
REAR DECK ........................................................................................................................................................16
INPUT SHAFT AND HITCH..................................................................................................................................18
MOWER SETUP FOR OPERATION .............................................................................................19
HITCH ADJUSTMENT..........................................................................................................................................19
INSTALLING DECK PTO SHAFTS.......................................................................................................................19
HITCHING THE MOWER TO THE TRACTOR .....................................................................................................20
CONNECTING THE PTO DRIVELINE..................................................................................................................20
CONNECTING THE HYDRAULICS......................................................................................................................21
CONNECTING THE PULL ROPE.........................................................................................................................21
MOWER SAFETY LOCKS....................................................................................................................................21
CHECK PTO DRIVELINE DURING MANEUVERS...............................................................................................22
CHECK TIRE CONTACT DURING TURNS..........................................................................................................22
DISCONNECTING THE MOWER.........................................................................................................................23
LONG-TERM STORAGE......................................................................................................................................23
OPERATING THE MOWER...........................................................................................................24
DAILY CHECK LIST.............................................................................................................................................24
RAISING AND LOWERING THE DECKS.............................................................................................................24
SETTING THE CUTTING HEIGHT.......................................................................................................................25
ENGAGING THE MOWER...................................................................................................................................26
MOWING..............................................................................................................................................................26
TRANSPORTING THE MOWER...................................................................................................27
MAINTENANCE.............................................................................................................................28
LUBRICATION.....................................................................................................................................................28
“V” BELT DRIVE...................................................................................................................................................33
FASTENER INSTALLATION TORQUE................................................................................................................34
BLADE SERVICING.............................................................................................................................................35
SPINDLE SERVICE .............................................................................................................................................37
HYDRAULICS......................................................................................................................................................39
SUPPORTING MACHINE FOR SERVICE............................................................................................................39
TIRES...................................................................................................................................................................40
LONG-TERM STORAGE......................................................................................................................................40
TROUBLESHOOTING..........................................................................................................................................41

TD65 Operator’s Manual
2
INTRODUCTION
Thank you for purchasing a TD65 series mower. This product is designed and manufactured to allow
safe and productive mowing of contoured areas. A well-maintained machine will provide years of
reliable service.
FOREWORD
This is the Operator’s Manual for the TD65 and TD65-2 mower. Keep it with the mower at all times.
This manual is intended as a guide to the safe use and maintenance of the machine, so before you
operate this machine, study this manual carefully.
Replace this manual immediately if it becomes lost.
This manual is not considered all-inclusive, so for further information on specific components, e.g. PTO
shafts etc refer to the respective documents included with the manual set for this machine.
The TD65 series are contour turf grass finishing mowers with a 12 (TD65-2) or 15.5 (TD65) foot cutting
width, and are designed to be pulled by a 25-50 PTO horsepower utility tractor. High blade tip speed
give these versatile mowers the ability to mow both contoured and flat terrain that requires a high
quality after-cut appearance
Features:
Three independent, fully floating decks
Low power input per cutting width
Cut height can be set on each deck between 1 inch and 5 inches
Combination of swivelling and rigid castor wheels ensures true straight line tracking and
easy turning without scuffing
Automatic mechanical deck locks for transport
Applications:
Golf course roughs
Turf grass farms
Corporate and industrial campuses
Park lands and recreational areas
Sports venues
Landscaped venues

TD65 Operator’s Manual
3
OSHA Training Requirements (USA)
The following training requirements have been taken from Title 29, Code of Federal Regulations Part
1928.57 (a)(6). www.osha.gov
Operator Instructions: At the time of initial assignment and at least annually thereafter, the employer
shall instruct every employee in the safe operation and servicing of all covered equipment with which he
is or will be involved, including at least the following safe operating practices.
In other jurisdictions
It is good practice, following the initial instruction and at least annually thereafter, the employer shall
instruct every employee in the safe operation and servicing of all covered equipment with which he is or
will be involved, including at least the following safe operating practices.
ITEMS INCLUDED WITH TD65 MOWER
TD65 Operator’s Manual
Service instructions for PTO drive shafts and safety clutches
Mower parts book
Blade balancer tool
SERIAL NUMBER LOCATION
The serial number plate for the machine is located on the left-hand
front frame.
For quick reference, record the following information:
Model: _______TD65 or TD65-2 ______
Serial Number: ___________________________
Date purchased: ___________________________
NOTE: The last digit in each TD65 serial number is a letter. This letter
denotes the geographic destination of the mower.
D EU Regulatory Region
B Non- EU Regulatory Region
There are differences in the parts required to service your mower based on this geographic code as are
referred to throughout the parts lists. Always state this information when contacting your selling dealer
and when ordering spare parts.
REPLACEMENT PARTS INFORMATION
Use only Genuine Original Equipment Manufacturers (O.E.M.)
replacement parts. The use of “will fit” parts may reduce machine
performance, void machine warranties and present a safety hazard.
Use Genuine OEM parts.
UNAUTHORIZED MODIFICATION
Modifications to the original design of the TD65 mower, including the use of unauthorized accessories
or non-genuine OEM parts, may affect the reliability of the machine or make it unstable or unsafe to
operate and perform as originally designed and intended. Persons or organizations that make
unapproved modifications (including operation without provided guards and shields) assume all liability
arising from or related to the modification including any adverse effect on the machine.
No modification can be made to the original design or assembly of the TD65 mower (including any and
all attachments, safety or control devices) without the prior written consent of the Progressive Turf
Equipment Inc.’s Engineering Manager (see contact information below). Progressive Turf Equipment
Inc. retains the right to reject all claims which arise from or are related to unauthorized modifications.

TD65 Operator’s Manual
4
Modifications are officially approved if at least one of the following conditions is met:
i. The attachment, accessory or part is distributed by Progressive Turf Equipment Inc. and is
intended for a TD65 mower application and installed in an approved manner as described
in Progressive Turf Equipment Inc.’s provided instructions; or
ii. The modification has been approved in writing by the Progressive Turf Equipment Inc.’s
Engineering Manager.
No other entity is authorized by Progressive Turf Equipment Inc. to provide such approval.
MISUSE OF EQUIPMENT
It is incumbent upon the owner and selling dealer along with their respective employees to warn and
discourage users about the misuse of the equipment whenever knowledge of misuse becomes known,
whether the act has, is or could occur. Such acts include, but not limited to: riding upon, use of non-
OEM parts, operation on unstable or steeper slopes than specified, operating in explosive or fire-hazard
areas, modifications that alter the original machine specifications or use other than originally intended,
etc.
NOTIFICATION OF UNAUTHORIZED MODIFICATION OR MISUSE
If any person, employee, agent, dealer or distributor becomes aware of any Unauthorized Modification
or Misuse of a TD65 mower, either past or intended, it is the responsibility of that person to ensure that
Progressive Turf Equipment Inc.’s Engineering Manager is notified of the occurrence promptly. That
person shall provide; the facts of the occurrence, location, machine serial number, name and contact
information of the persons involved.
Send correspondence regarding Unauthorized Modification or Misuse to:
Progressive Turf Equipment Inc.
Box 940, 137 West William St.
Seaforth, Ontario, N0K 1W0
Canada
Attn: Engineering Manager
PRODUCT DESIGN
The TD65 mower has been designed and produced using generally acceptable manufacturing
processes as is standard in the industry for the type of equipment that is similar to the machine. As
such, the useful life of the machine is ten (10) years from the date of manufacture.
The official language of the manufacturer is English.
No responsibility is assumed for translations in other languages, which do not correspond to the original
meaning.
Under our policy of continuous improvement, we reserve the right to change specifications and designs
without prior notice. The illustrations shown do not necessarily represent the standard version of
product offered by Progressive Turf Equipment Inc.
*For clarity, some illustrations used in this manual show depictions with certain components removed.
Never operate the machine with any component or guard removed.

TD65 Operator’s Manual
5
SPECIFICATIONS
TD65-2 TD65
Tractor Requirement
Size (hp) 25-40....................................30-50
PTO Input Speed (rpm) ...................540 ..................
Max. Hydraulic Pressure (psi) ..................2500 .................
Machine Specifications
Cutting Width (ft) 12 .....................................15 1/2.
No. of Blades 7 .......................................... 9
Turning Radius (uncut circle, in) 24 ......................................... 0
Ground Pressure (psi) 7 .......................................... 8
Cutting Height (in) Minimum .....................1.....................
Maximum .....................5.....................
Increment ...................3/8...................
Transport Features Max. Speed ............... 20 mph ...............
Safety .SMV Sign & Safety Chain.
Mower Decks
Configuration 3 deck staggered independent
Suspension 4-way floatation
Construction 3/16 in. (7 ga) thk with reinforced welded tube frame
Spindles 30mm shaft, double ball bearing /w integral blade stiffener
Blades 23”diameter, 5/16” thk. (high-lift std., low-lift & mulching optional)
Blade Mounting Two bolts/nuts per blade (No internal threads)
Blade Speed 3040 rpm / 18287 sfpm
Tires (10) 15x6-6, 4 ply, 5 Bolt /w tapered roller bearing support
Anti Scalp Impact Resistant Rollers (front & rear of each deck)
Power Transmission
Input Shaft 1 3/8 dia –6 Spline, 80° Constant Velocity /w auto locking collar
Deck Drive Shafts Cat. 2 1 3/8 dia –6 spline /w quick connect yokes
Gearboxes (4) Cast Iron Housing /w Bevel gears
Deck Drive Fiber reinforced V-Belts
Belt Tensioning Positive draw bolt tensioner (1 per deck)
Transport Tires (2) Heavy Duty 18.5 x 9.5 –8, 4 ply, 5 bolt.
Productivity (acres/hr*) 2 mph 2.9.......................................3.75
4 mph 5.8........................................7.5
6 mph 8.7.......................................11.3
Transport Dimensions (ft) Width 7.5........................................8.5
Height 5.5........................................7.5
Length ....................14 ...................
Weight (lb) Machine 2380 .................................... 2720
Tongue (transport) 445 ...................................... 580
Tongue (mowing) 235 ...................................... 330
Optional Low-Lift Blades
Mulching kit (incl. blades & mulching shrouds)
Discharge deflector kits (Steel deflector or chain)
*assumes no stopping or overlap

TD65 Operator’s Manual
6
COMPONENT IDENTIFICATION
NOTES
1) Throughout this manual, references are made to right and left
directions. These are determined by standing at the rear of the
equipment and facing the direction of forward travel.
FRONT
OPERATOR’S
MANUAL
PARKING
JACK
INPUT PTO
SHAFT
DRAW
CLEVIS
HOSE
SUPPORT
PULL
ROPE
DECK LIFT
CYLINDERS
DECK SAFETY LOCKS
ANTI-SCALP
ROLLER
REAR
HYDRAULIC
COUPLERS
DECK GEAR
BOX
TRANSPORT
SAFETY CHAIN
4-WAY GEAR
BOX
INTERMEDIATE
BEARING AND
SHIELD

TD65 Operator’s Manual
7
SAFETY RULES
All rotary mowers are potentially dangerous machines; this mower has
been designed to minimize the safety risks to the operator, bystanders
and property. This section of the Operator’s Manual details a number
of safety rules pertaining to the operation and maintenance of
Progressive Turf Equipment mowers. In order to minimize risks and
promote safety at all times, these rules must always be followed and
obeyed.
Further safety rules and warning texts are given within the respective
sections of this manual.
IMPORTANT! - When it comes to safety, nothing will ever replace
a careful operator.
It is imperative that the operator and safety personnel read and
understand all of the safety information in this manual before
proceeding. Failure to follow the instructions or heed the warnings
could result in injury or death.
Proper care is your responsibility.
The manufacturer cannot anticipate every possible circumstance that
might involve a hazard. The hazard alerts in this publication and on the
product, are therefore not all inclusive. If a tool, procedure, work
method, or operating technique not specifically recommended by the
manufacturer is used, it is your responsibility to ensure that it is safe for
you and others. You should also ensure the machine will not be
damaged or made unsafe by the operation, maintenance, or repair
procedures you choose. Modifications or adaptations to the machine
are not allowed.
Various jurisdictions have specific requirements for work zone safety.
Know and adhere to your local requirements. Treat the instructions in
this manual as minimum requirements for safe operation.
SAFETY ALERT SYMBOL
This symbol appears at various points in the manual together with a
signal word and warning text. It means –Be alert! Your safety is
involved. This symbol is used throughout the manual to call attention to
areas in which carelessness or failure to follow specific procedures
may result in personal injury or component damage / malfunction or
both.
HAZARD SERIOUSNESS LEVEL
The following signal words are found throughout the manual together
with the safety alert symbol to indicate the seriousness level of
identified hazards. Their selection is based on the consequence of
human interaction with a hazard.
DANGER! –Hazards or unsafe practices which WILL result in
severe personal injury or death.
WARNING! –Hazards or unsafe practices that COULD result
in severe personal or death.
CAUTION! –Hazards or unsafe practices that COULD result
in minor personal injury or product or property damage

TD65 Operator’s Manual
8
GENERAL SAFETY PRECAUTIONS
The operator of this machine must have sufficient knowledge
and instructions in the care and operation of this mower and the
power unit being used before he / she uses the machine. Do not
allow unauthorized persons or children to operate the machine.
Do not allow riders on the machine.
It is the obligation of the operator to make sure that all guards
and shields are in place on the machine. Safety decals must be
in place and be readable –accidents may otherwise occur.
Contact your dealer or the manufacturer for replacement
manuals or decals.
Never use a machine that does not have an operator’s manual
available. Learn and understand the safety signs and symbols on
the machine and the operator instructions before you begin to
use the machine.
Wear personal protective equipment. Know and use the
protective equipment that is to be worn when operating or
servicing the machine. Hard hats, protective glasses and face
shields, protective shoes, gloves, reflector type vests, and ear
protection are types of equipment that may be required.
Prolonged exposure to loud noise can cause hearing damage.
Never operate a mower while under the influence of drugs or
alcohol. These make reflexes slow and put you and others in
grave danger. Always make sure you have full concentration
while mowing.
Adhere strictly to all regulations at the worksite pertaining to the
operation of this equipment.
Always disengage power takeoff (PTO) when transporting or
traveling between work sites.
Be prepared for emergencies. Have a first aid kit, fire
extinguisher and emergency contact information available at the
work site.
POWER UNIT SAFETY
The operator must have sufficient knowledge in the care and
operation of the power unit (tractor) before connecting power unit
to mower. Read and understand power unit operator’s manual
before connecting mower.
Power unit must be equipped with ROPS and seat belt. Foldable
ROPS must be secured in the upright position. Follow
recommendations of power unit manufacturer. Seat belt must be
worn at all times.
Power unit must be equipped with a 1-3/8” 6 spline 540 RPM
PTO connection. Never use PTO adapters to connect
implements. Never connect mower driveline to 1000 RPM PTO.
Hydraulic circuits to control mower functions must be set to 2500
psi maximum working pressure.

TD65 Operator’s Manual
9
OPERATING EQUIPMENT SAFELY
Never allow persons to stand between power unit and mower
while backing power unit up to hitch the mower.
Before hitching mower to power unit, place transmission in
neutral, set park brake, and turn engine off. Remove the ignition
key.
Make sure locking collar on PTO shaft is properly locked. If the
PTO shaft comes off during operation, personal injury or
equipment damage could result.
Tall grass can hide obstacles. Carefully walk the entire area to
be mowed beforehand. Look for debris, rocks, tree limbs etc. that
will damage or be thrown by the mower blades. Identify objects
that cannot be removed. Set mower cutting height to avoid
contact.
Disengage the PTO when crossing gravel areas or roadways.
Disengage the PTO and turn power unit off upon striking any
object. Inspect mower and repair any damage before continuing.
Mower blades can cause small objects and debris to be thrown
from under the mower deck at high speeds, up to 300 ft away.
Objects ejected by the mower blades can cause severe injury.
If the equipment should start to vibrate abnormally during
operation, stop the mower, shut down power unit, and
immediately check for the cause. Excess vibration is generally
an indication of a problem. Replace bent or damaged parts, do
not attempt to straighten a bent blade.
Ensure that no bystanders are within 10 ft of mower when wing
transport locks are released.
Keep all bystanders well away from the machine when it is
operating. Always maintain a safe operating distance from
personnel, other equipment, or vehicles.
Never operate the mower with shields or guards removed.
Never tamper with safety devices or operate the mower with
them removed. Check proper operation regularly.
Always disengage PTO, place all controls in neutral, turn power
unit off, set parking brake, and remove key before dismounting,
for any reason.
Never place hands or feet under mower deck when the mower is
operating or power unit engine is running.
Use extreme care when operating on uneven terrain.
Reduce speed when operating on slopes during wet conditions,
especially when making sharp turns.
Do not use the mower in limited visibility (e.g. at dusk, in fog,
heavy rain etc.). Mow only in daylight or good artificial light.
Disengage PTO and ensure blades are completely stopped
before raising wings.
Ensure deck safety locks are securely engaged before
transporting mower with wings in raised position.

TD65 Operator’s Manual
10
Be aware of over-head obstacles such as trees, building
overhangs when transporting mower.
Keep away from overhead electrical lines. Electrocution can
occur without direct contact
Clean reflectors, Slow Moving Vehicle sign and lights before
transporting. Use power unit hazard lights.
Before disconnecting from power unit, always place controls in
neutral, set park brake, turn engine off, and wait for all moving
parts to stop. Relieve hydraulic pressure per power unit
manufacturer’s instructions.
Ensure mower parking jack is securely fastened to mower frame
with supplied pin before removing hitch draw pin.
MAINTENANCE SAFETY PRECAUTIONS
Never make adjustments or repairs with the engine running.
Always disengage PTO, engage parking brake, turn engine off,
lower wings to cutting position and relieve hydraulic pressure
before performing any maintenance.
Observe and perform proper lock-out procedures for power unit if
attached to mower during service.
Keep nuts and bolts tight and properly torqued, especially blade
attachment bolts. Check that all cotter pins are properly installed.
Keep equipment in good condition.
Keep mower free of grass, leaves, or other debris build-up.
Never work on raised mower decks without safety locks in place.
Periodically check condition of safety devices, guards, and
deflectors. Replace only with manufacturer’s recommended
parts.
Inspect and replace damaged blades. Use only original OEM
parts. Blades can fail from poor maintenance practices.
Handle mower blades carefully. They are sharp and can cut
unprotected skin. Use caution and wear gloves when handling
them.
Check to make sure hydraulic hoses are not worn or damaged,
and are routed to avoid chafing.
Immediately replace any hydraulic hose that shows signs of
swelling, wear, leaks or damage so it does not burst.
Do not use your hand to check for hydraulic oil leaks. Use a
piece of cardboard instead.
Hydraulic fluid escaping under pressure can penetrate the skin
causing serious injury. If skin penetration occurs, seek medical
attention immediately. Relieve all pressure before disconnecting
hoses.
Do not bend or strike hydraulic lines, tubes or hoses, or reinstall
them in a bent or damaged condition.
Inspect tires daily for wear or damage. Check tire pressures
weekly with an accurate pressure gauge. Do not inflate tires
beyond 35 psi.

TD65 Operator’s Manual
11
Mounting and dismounting tires from rims can be dangerous and
should be performed by trained personnel using correct tools,
equipment and procedures.
Never perform service on a machine that is supported solely by a
jack. Always ensure proper blocking is placed to support load
during service. Do not support the machine on cinder blocks,
hollow tiles or other members that may fail under
continuous load.
WELDING AND GRINDING WORK PRECAUTIONS
IMPORTANT! A fire extinguisher should be easily accessible
during all welding work.
Welding repairs are to be performed by a trained welder with proper
service instructions. Know the material to be welded and select the
correct welding procedure and materials (electrodes, rods, wire) that
will provide a weld metal strength equivalent to the parent material.
Move the machine to a clean, safe area before welding, grinding or
using a cutting torch on it. This type of work should only be done in a
clean area and not in places that contain combustible liquids, such as
fuel tanks, hydraulic pipes or similar.
Connect arc welder ground as close as possible to work area.
Work with extra care when welding, grinding or torch cutting near
flammable objects.
WORKING ON PAINTED SURFACES
Heated paint gives off poisonous gases. Therefore, paint must be
removed from an area with a radius of at least 4 in (10 cm) before
carrying out welding, grinding, or gas cutting. In addition to the health
hazard, the weld will be of inferior quality and strength if the paint is not
removed.
WORKING ON GALVANIZED / PLATED SURFACES
Only qualified welders should attempt a weld repair on galvanized or
plated components. Proper pre-welding surface preparation is
required.
Always ensure proper ventilation, wear proper respiratory protective
equipment and avoid direct contact with smoke emitted from welding
process.

TD65 Operator’s Manual
12
HYDRAULIC SYSTEM SERVICE PRECAUTIONS
Risk of personal injury! Wear safety
glasses and use protective gloves.
Relieve all trapped pressure before performing any service to the
hydraulic system. Pressure can be maintained in the hydraulic circuits
long after the power source and pump have been shut down.
Relieve all pressure before disconnecting hoses or tubes.
Tighten all connections before applying pressure.
It is important that each person who comes in contact with the machine
be alert to any faults.
Follow these basic precautions:
Never adjust a pressure relief valve or other pressure-limiting
device to a higher pressure than specified.
Check to make sure hydraulic hoses are not worn or damaged,
and are routed to avoid chafing.
When connecting mower to tractor ensure hydraulic hoses
have sufficient slack for negotiating turns and uneven terrain.
Immediately replace any hydraulic hose that shows signs of
swelling, wear, leaks or damage so it does not burst.
Do not use your hand to check for hydraulic oil leaks. Use a
piece of cardboard instead. Hydraulic fluid escaping under
pressure can penetrate the skin causing serious injury. If skin
penetration occurs, seek medical attention immediately.
Relieve all pressure before disconnecting hoses.
Do not bend or strike high-pressure
lines, tubes or hoses, or reinstall them
in a bent or damaged condition.
HYDRAULIC OIL HANDLING PRECAUTIONS
Oils can irritate and damage the eyes, throat, and sensitive skin. Avoid
contact.
Petroleum based oils are hazardous to the environment. Take special
care not to spill or discharge these fluids. Use approved containers and
methods to handle and dispose of them.
Use an authorized disposal and recycling company.

TD65 Operator’s Manual
13
SAFETY DECALS
DECAL LOCATIONS
If decals become faded, damaged, or lost, replace immediately.
TD65-2 Order Decal Kit 522302
TD65 Order Decal Kit 522303
ITEM
DESCRIPTION
QTY
ITEM
DESCRIPTION
QTY
1
DANGER –READ MANUAL
1
11
BLADE HARDWARE
1
2
CAUTION - TURNING
1
12
SERIAL PLATE
1
3
CAUTION –REPLACE SHIELDS
8
13
MOWER MODEL
1
4
COMPANY NAME
1
14
DANGER –OUTER TUBE
3
5
DANGER - BLADE HAZARD
7
15
CE WARNING DECAL
1
6
WARNING –OEM PARTS
1
16
SAFETY SIGN –INNER GUARD
2
7
CAUTION –DISENGAGE PTO
1
17
SAFETY SIGN –OUTER GUARD
2
8
GREASING SCHEDULE
1
18
DANGER –INNER SHIELD
3
9
PTO GREASING
1
19
GREASE POINT
20
10
NOTICE –HITCH SETUP
2
5
13(BOTH SIDES)
5
10
2
1
6
9
12
(2) SHAFTS 16
17
18
(3) SHAFTS 14
15
5
5
5
3(BOTH
SHIELDS)
3(BOTH SHIELDS)
5
5
3(BOTH
SHIELDS)
3
3
8
7
11

TD65 Operator’s Manual
14
DECAL LISTING
ITEM 1 ITEM 2
(209175) (209171)
ITEM 3 ITEM 4 ITEM 5
(209113) (521817) (209173)
ITEM 6 ITEM7 ITEM 8
(209115) (521820) (526003)
ITEM9 ITEM 10 ITEM 11
(521119) (521784) (209182)

TD65 Operator’s Manual
15
PROGRESSIVE
65-2 TRI-DECK
ITEM 13 - TD65-2
(521837)
PROGRESSIVE
65”TRI-DECK
ITEM 13 - TD65
(521838)
ITEM 14
(521455)
ITEM 15
(521451)
ITEM 17
(210237)
ITEM 16 ITEM 18
(210239) (210238)
ITEM 19
(521014)

TD65 Operator’s Manual
16
ASSEMBLY INSTRUCTIONS
SET-UP
The mower is shipped partially assembled to facilitate shipment in enclosed vans. The rear mower
deck and various smaller components must be assembled at the dealer prior to pre-delivery inspection
and delivery to the customer. Approximately 1 1/2 hours are required to complete the mower to field
ready condition.
Assembly will be easier if components are aligned and loosely assembled before tightening hardware.
Recommended torque values are found on page Error! Bookmark not defined.. Select a suitable
working area. A tractor or portable hydraulic supply is necessary to complete assembly. Refer to the
mower parts list for component location reference.
Assembly should be completed by a competent individual who has an
understanding of safe machinery operation practices and tool operation.
Always use personal protection devices such as eye and ear protection
during assembly. Ensure the area is free of hazards and can
accommodate the assembly of the mower
Remove all components that are tied to the mower for shipping before beginning the assembly process.
These include: (2) square casters, hitch assembly, rear deck lock / cylinder assembly, rear cylinder
hoses, PTO support, hose support and input shaft.
REAR DECK
1) The TD65 rear deck must be lifted from the frame for final assembly.
Ensure proper devices are used to lift deck (approximate deck weight 600lb).
Securely fasten lifting device to deck assembly and lift sufficiently to take the weight
of the deck assembly.
Remove the (2) shipping brackets securing the deck to the upright frame and cut the
banding securing the deck to the main frame.
2) Lift the rear deck away from the machine and install the square castor wheels. Lower the deck to
the ground so that it rests on its wheels.
3) Unwrap the tractor connection hoses and pull rope. Connect the hydraulic hoses to a hydraulic
power source. Disengage transport lock and lower wings to the ground.
4) Remove the line pressure in the hydraulic hoses.

TD65 Operator’s Manual
17
5) Manually lower the rear deck lift and pull arms.
6) Install the rear deck safety / cylinder assembly with the supplied pins. The assembly is installed
on the cylinder mount in the same orientation as packaged. The rod-end of the cylinder is
fastened to the rear-lift mechanism with the lock bar & cylinder ports facing up. Connect the pull
chain from the deck safety to the rear deck safety.
7) Install the 90 degree hydraulic adapter in the rod end of the cylinder. The adapter port should
face toward the front of the machine when the cylinder is in the lowered position.
8) Install the 45 degree hydraulic adapter in the base end of the cylinder. The adapter port should
face UP when the cylinder is in the raised position.
*NOTE - all connections are pipe thread and require thread sealant on all joints at assembly
9) Connect the hydraulic hoses to the rear deck cylinder. The long hose (31”) connects the bottom
tee on the wing lock frame to the 90 degree adapter at the rod end of the cylinder. The short
hose (24”) is connects the top tee on the wing lock frame to the 45 degree adapter at the base
end of the cylinder.
10) Using the hydraulic power source, cycle the lift cylinders up and down fully 3 or 4 times to remove
all entrapped air from the system.
PULL ARMS
REAR DECK LIFT
SAFETY / CYLINDER ASSEMBLY

TD65 Operator’s Manual
18
11) Roll the rear deck into place. Install lift arms with pins & fasteners supplied (shipped fastened to
the deck).
12) Install rear deck PTO shaft. (The end with the small bell marked with a tractor goes on the four-
way gear-box). Ensure shafts are phased properly (see Page 19)
INPUT SHAFT AND HITCH
13) Remove intermediate bearing shield and remove spacer bushing warning tag attached to
intermediate shaft stub. Be sure that the small spacer bushing is in place.
14) To install the input shaft:
Remove ½” UNC retaining bolt/nut from input shaft.
Remove notification tag from intermediate shaft hanger bearing, ensure gold
coloured spacer ring is present against bearing inner race.
Disconnect input shaft shield at clamp yoke end and slide shield exposing the clamp
yoke (see input shaft service instructions in mower manual storage tube).
Install input shaft clamp yoke on intermediate shaft, ensuring gold coloured spacer
ring is in place between the input shaft yoke and hanger bearing race.
Reinstall ½” UNF retaining bolt in input shaft yoke, torque to 85 ft-lb.
Reinstall input shaft shield per input shaft service instructions.
Fasten input shaft guard retaining chain to mower main frame.
15) Re-install intermediate bearing shield.
16) Install hose support assembly. Run the safety pull rope and hydraulic lines through the eye of the
hose support rod.
17) Install the front hitch & PTO support with the bolt provided.
18) Grease the intermediate support bearing and the rear deck lift arm pivots, and check over mower
to find any other spots that missed greasing (All other pivots and wheels are greased before
shipping)
TRANSPORT TIRES
1) Check air pressure in the tires and adjust according to specifications on Page 40.
The mower is now ready for pre-delivery inspection and lubrication prior to first use.