Progressive Turf Equipment TDR-X Installation and operation manual

Operator’s Manual & Parts List
TDR-X
Serial No. 20111003 and up
PROGRESSIVE TURF EQUIPMENT INC.
137 WEST WILLIAM STREET
SEAFORTH, ONTARIO
CANADA N0K 1WO
TOLL FREE: 800 668-8873
www.progressiveturfequip.com
ISSUE DATE: May 2020
P.N. 120596

TDR-X Operator’s Manual
TABLE OF CONTENTS PAGE
INTRODUCTION..............................................................................................................................3
FOREWORD ....................................................................................................................................3
ITEMS INCLUDED WITH TDR-X MOWER............................................................................4
SERIAL NUMBER LOCATION...............................................................................................4
REPLACEMENT PARTS INFORMATION .............................................................................4
UNAUTHORIZED MODIFICATION........................................................................................5
MISUSE OF EQUIPMENT .....................................................................................................5
NOTIFICATION OF UNAUTHORIZED MODIFICATION OR MISUSE..................................5
PRODUCT DESIGN...............................................................................................................5
SPECIFICATIONS ...........................................................................................................................6
COMPONENT IDENTIFICATION ....................................................................................................7
SAFETY RULES..............................................................................................................................8
SAFETY ALERT SYMBOL.....................................................................................................8
HAZARD SERIOUSNESS LEVEL .........................................................................................8
GENERAL SAFETY PRECAUTIONS ....................................................................................9
POWER UNIT SAFETY..........................................................................................................9
OPERATING EQUIPMENT SAFELY...................................................................................10
MAINTENANCE SAFETY PRECAUTIONS.........................................................................11
WELDING / GRINDING WORK PRECAUTIONS ................................................................12
HYDRAULIC SYSTEM SERVICE PRECAUTIONS.............................................................13
SAFETY DECALS................................................................................................................14
DECAL LISTING...................................................................................................................15
ASSEMBLY INSTRUCTIONS .......................................................................................................16
INSTALLING DECK PTO SHAFTS:.....................................................................................17
MOWER SETUP FOR OPERATION .............................................................................................19
DRAWBAR ADJUSTMENT..................................................................................................19
HITCHING THE MOWER TO THE TRACTOR....................................................................20
STOWING THE JACK..........................................................................................................20
CONNECTING THE PTO TO THE TRACTOR....................................................................20
CONNECTING THE HYDRAULICS.....................................................................................21
CONNECTING THE PULL ROPE........................................................................................21
MOWER SAFETY LOCKS...................................................................................................21
DECK LOCK SYSTEM.........................................................................................................21
TRANSPORT LOCK.............................................................................................................22
CHECK PTO LENGTH - TURNING AND ON HILLS...........................................................23
CV JOINT INPUT SHAFT.....................................................................................................24
DISCONNECTING THE MOWER........................................................................................24
ADJUSTING THE MOWER FOR CUTTING .................................................................................26
SETTING HEIGHT OF CUT.................................................................................................26
OPERATING THE MOWER...........................................................................................................27
DAILY CHECK LIST.............................................................................................................27
RAISING / LOWERING THE WINGS & DECKS..................................................................27
ENGAGING THE PTO..........................................................................................................28
MOWING..............................................................................................................................28
Pro Lift-N-TurnTM SYSTEM...................................................................................................29
TRANSPORTING THE MOWER ...................................................................................................30
TIE DOWN LOCATIONS......................................................................................................30
MAINTENANCE.............................................................................................................................31
LUBRICATION .....................................................................................................................32

TDR-X Operator’s Manual
2
CHECK OPERATION OF LOCK SYSTEM..........................................................................34
“V” BELT DRIVE...................................................................................................................36
FASTENER INSTALLATION TORQUE...............................................................................37
BLADE SERVICING.............................................................................................................38
SPINDLE SERVICE .............................................................................................................41
HYDRAULICS ......................................................................................................................43
SUPPORTING MACHINE FOR SERVICE...........................................................................44
TRANSPORT TIRES............................................................................................................44
LONG-TERM STORAGE .....................................................................................................44
TROUBLE SHOOTING ........................................................................................................45
Si usted No Lee Ingles, Pida Ayuda a Alguien Que Se Lo Lea
Para Que le Traduzca Las Medidas de Seguridad

TDR-X Operator’s Manual
3
INTRODUCTION
Thank you for purchasing a TDR-X mower. This product is designed and manufactured to allow safe and
productive mowing of contoured areas. A well-maintained machine will provide years of reliable service.
FOREWORD
Keep this manual with the mower at all times. This manual is intended as a guide to the safe use and
maintenance of the machine, so before you operate this machine, study this manual carefully.
Replace this manual immediately if it becomes lost.
This manual is not considered all-inclusive, so for further information on specific components, e.g. PTO
shafts etc refer to the respective documents included with the manual set for this machine.
The TDR-X mower is a contour roller turf grass finishing mower with a 10.5 foot cutting width, and is
designed to be pulled by a 35-40 PTO horsepower utility tractor. These versatile mowers have the ability
to mow both contoured and flat terrain that requires a high quality, finished after cut appearance. High
blade tip speed leaves a second-to-none after cut appearance. 6-way floating decks, and an Adaptive
Swivel Hitch isolates the tractor from the mower allowing truer contour tracking.
Features:
•Three independent floating decks
•Cut height can be set on each deck between 3/8 inch and 3 3/8 inches
•10.5 foot cutting width
•Adaptive Swivel Hitch
•Pro Lift-N-TurnTM allows three decks to be temporarily raised slightly off the ground with the
PTO still engaged
•Automatic mechanical deck locks for transport
Applications:
•Golf course roughs, fairways and bunker surrounds
•Corporate and industrial campuses
•Park lands and recreational areas & sports venues
•Landscaped venues
TDR Series Mower Application Guide
Model
TDR-X
Soil Type
All (firm sandy)
Turf Condition
All conditions
Comments
For use in areas where ride-on reel-type mowers cannot be used.
OSHA Training Requirements (USA)
The following training requirements have been taken from Title 29, Code of Federal Regulations Part
1928.57 (a)(6). www.osha.gov
Operator Instructions: At the time of initial assignment and at least annually thereafter, the employer shall
instruct every employee in the safe operation and servicing of all covered equipment with which he is or
will be involved, including at least the following safe operating practices.
In other jurisdictions:
It is good practice, following the initial instruction and at least annually thereafter, that the employer
instruct every employee in the safe operation and servicing of all covered equipment with which he is or
will be involved, including at least the following safe operating practices.

TDR-X Operator’s Manual
4
ITEMS INCLUDED WITH TDR-X MOWER
TDR-X Operator’s Manual & Parts List
Service instructions for PTO drive shafts
Blade balancer tool –*One piece blades only, not used for swing blades
SERIAL NUMBER LOCATION
The serial number plate for the machine is located on the
left-hand front frame.
For quick reference, record the following information:
Model: __________ TDR-X __________
Serial Number: ___________________________
Date purchased: ___________________________
NOTE: The last digit in each TDR-X serial number is a letter. This
letter denotes the geographic destination of the mower.
D EU Regulatory Region
B Non- EU Regulatory Region
There are differences in the parts required to service your mower based on this geographic code as are
referred to throughout the parts lists. Always state this information when contacting your selling dealer
and when ordering spare parts.
REPLACEMENT PARTS INFORMATION
Use only Genuine Original Equipment Manufacturers (O.E.M.) replacement parts. The use of “will fit”
parts may reduce machine performance, void machine warranty and present a safety hazard. Use only
Genuine OEM replacement parts.
Under our policy of continuous improvement, we reserve the right to change specifications and
designs without prior notice. The illustrations shown do not necessarily represent the standard version
of product offered by Progressive Turf Equipment Inc.

TDR-X Operator’s Manual
5
UNAUTHORIZED MODIFICATION
Modifications to the original design of the TDR-X mower, including the use of unauthorized accessories
or non-genuine OEM parts, may affect the reliability of the machine or make it unstable or unsafe to
operate and perform as originally designed and intended. Persons or organizations that make
unapproved modifications (including operation without provided guards and shields) assume all liability
arising from or related to the modification including any adverse affect on the machine.
No modification can be made to the original design or assembly of the TDR-X mower (including any and
all attachments, safety or control devices) without the prior written consent of the Progressive Turf
Equipment Inc.’s Engineering Manager (see contact information below). Progressive Turf Equipment Inc.
retains the right to reject all claims which arise from or are related to unauthorized modifications.
Modifications are officially approved if at least one of the following conditions is met:
i. The attachment, accessory or part is distributed by Progressive Turf Equipment Inc. and is
intended for a TDR-X mower application and installed in an approved manner as described
in Progressive Turf Equipment Inc.’s provided instructions; or
ii. The modification has been approved in writing by the Progressive Turf Equipment Inc.’s
Engineering Manager.
No other entity is authorized by Progressive Turf Equipment Inc. to provide such approval.
MISUSE OF EQUIPMENT
It is incumbent upon the user, owner and selling dealer of this equipment along with their respective
employees to warn and discourage users about the misuse of the equipment whenever knowledge of
misuse becomes known, whether the act has, is or could occur. Such acts include, but not limited to:
riding upon, use of non-OEM parts, operation on unstable or dangerous terrain, operating in explosive or
fire-hazard areas, modifications that alter the original machine specifications or use other than originally
intended, etc.
NOTIFICATION OF UNAUTHORIZED MODIFICATION OR MISUSE
If any person, employee, agent, dealer or distributor becomes aware of any Unauthorized Modification or
Misuse of a TDR-X mower, either past or intended, it is the responsibility of that person to ensure that
Progressive Turf Equipment Inc.’s Engineering Manager is notified of the occurrence promptly. That
person shall provide; the facts of the occurrence, location, machine serial number, name and contact
information of the persons involved.
Send correspondence regarding Unauthorized Modification or Misuse to:
Progressive Turf Equipment Inc.
Box 940, 137 West William St.
Seaforth, Ontario, N0K 1W0
Canada
Attn: Engineering Manager
PRODUCT DESIGN
The TDR-X mower has been designed and produced using generally acceptable manufacturing
processes as is standard in the industry for the type of equipment that is similar to the machine. As such,
the useful life of the machine is ten (10) years from the date of manufacture.
The official language of the manufacturer is English.
No responsibility is assumed for translations in other languages, which do not correspond to the original
meaning.

TDR-X Operator’s Manual
6
SPECIFICATIONS
Tractor Requirement
PTO Horsepower............................................................................35-40 hp
PTO Input Speed............................................................................540 rpm
Maximum Hydraulic Pressure ........................................................3000 psi
Maximum Implement Hydraulic Flow .............................................17 US gpm
Machine Specifications
Cutting Width ........................................................10.5 ft.
Turning Radius Zero-Turn Capability.
Cutting Height Minimum..........................................3/8 in.
Maximum.........................................3 3/8 in
Flexibility
Mower Decks Fore & Aft Rotation..........................+/- 10°
Left & Right Rotation.......................+/- 10°
Vertical Movement ..........................+/-8 in
Hitch Rotation...........................................6-way movement
Mower Decks
Configuration 3 deck independent staggered
Floatation 6-way
Construction Welded Steel –3/16 in. (7 ga) thickness
Spindles 30mm spindles are each carried in 2 maintenance free ball
bearings, which are housed, in a precision machined hub
Blades High lift, heat treated, alloy steel blades 5/16” x 2 ½” x 16 3/4” (3)
per deck or Pro EZII replaceable blade tips
Blade Mounting Two bolts/nuts per blade (No internal threads)
Rollers Full width, heavy wall reinforced ends, with HEX drive, supported
by (2) 1.25 hex bearings in ductile iron housing.
Power Transmission
Input Shaft 1 3/8 dia –6 Spline
80° Constant Velocity /w auto locking collar
Gearbox Cast Iron Housing /w Helical gears
Deck Drive Fiber reinforced V-Belts, 2 per deck
Belt Tensioning Positive Draw bolt tensioner (1 per deck)
Transport Tires (2) Heavy Duty 23 X 9.5-12, 5 bolt.
Productivity* 4 mph ..............................................5.0 acres / hr.
6 mph ..............................................7.6 acres / hr.
*Assumes no overlap or turning
Transport Dimensions Width...............................................6ft. 6in. (Max)
Height..............................................6 ft
Length .............................................11ft 6in.
Weight Machine...........................................3250 lbs
Under our policy of continuous improvement, we reserve the right to change specifications and
designs without prior notice. The illustrations shown do not necessarily represent the standard
version of product offered by Progressive Turf Equipment Inc.

TDR-X Operator’s Manual
7
COMPONENT IDENTIFICATION
NOTES
1) Throughout this manual, references are made to right and left
directions. These are determined by standing at the rear of the
equipment and facing the direction of forward travel.
2) Blade rotation is identical on all three decks, all locations. The
blades are expressed as “Left Hand” (LH)” and rotate counter-
clockwise as viewed from the top of the mower.
WING LIFT
CYLINDER
(BOTH SIDES)
GEAR BOX
(ONE EACH DECK)
HYDRAULIC
COUPLERS
INPUT PTO
SHAFT
SWIVEL
HITCH
PARKING
JACK
PULL
ROPE
OPERATOR’S
MANUAL
DECK ROLLER
(FRONT& REAR EACH DECK)
4-WAY GEAR
BOX WITH
COVER
HEX ROLLER-END
BEARING (4 PER DECK)
INPUT SHAFT
SUPPORT
HEIGHT of CUT
ADJUSTMENT
(4 PER DECK)
DECK LOCK
(ALL DECKS)
DECK FLOAT SLOT
(ALL DECKS)

TDR-X Operator’s Manual
8
SAFETY RULES
All rotary mowers are potentially dangerous machines; this mower has
been designed to minimize the safety risks to the operator, bystanders
and property. This section of the Operator’s Manual details a number
of safety rules pertaining to the operation and maintenance of
Progressive Turf Equipment mowers. In order to minimize risks and
promote safety at all times, these rules must always be followed and
obeyed.
Further safety rules and warning texts are given within the respective
sections of this manual.
IMPORTANT! - When it comes to safety, nothing will ever replace
a careful operator.
It is imperative that the operator and safety personnel read and
understand the safety information in this manual before proceeding.
Failure to follow the instructions or heed the warnings could result in
injury or death.
Proper care is your responsibility.
The manufacturer cannot anticipate every possible circumstance that
might involve a hazard. The hazard alerts in this publication and on the
product, are therefore not all inclusive. If a tool, procedure, work
method, or operating technique not specifically recommended by the
manufacturer is used, it is your responsibility to ensure that it is safe for
you and others. You should also ensure the machine will not be
damaged or made unsafe by the operation, maintenance, or repair
procedures you choose. Modifications or adaptations to the machine
are not allowed.
Various jurisdictions have specific requirements for work zone safety.
Know and adhere to your local requirements. Treat the instructions in
this manual as minimum requirements for safe operation.
SAFETY ALERT SYMBOL
This symbol appears at various points in the manual together with a
signal word and warning text. It means –Be alert! Your safety is
involved. This symbol is used throughout the manual to call attention to
areas in which carelessness or failure to follow specific procedures may
result in personal injury or component damage / malfunction or both.
HAZARD SERIOUSNESS LEVEL
The following signal words are found throughout the manual together
with the safety alert symbol to indicate the seriousness level of
identified hazards. Their selection is based on the consequence of
human interaction with a hazard.
DANGER! –Hazards or unsafe practices which WILL result in
severe personal injury or death.
WARNING! –Hazards or unsafe practices that COULD result
in severe personal injury or death.
CAUTION! –Hazards or unsafe practices that COULD result
in minor personal injury or product or property damage

TDR-X Operator’s Manual
9
GENERAL SAFETY PRECAUTIONS
•The operator of this machine must have sufficient knowledge and
instructions in the care and operation of this mower and the
power unit being used before he / she uses the machine. Do not
allow unauthorized persons or children to operate the machine.
Do not allow riders on the machine.
•It is the obligation of the operator to make sure that all guards
and shields are in place on the machine. Safety decals must be
in place and be readable –accidents may otherwise occur.
Contact your dealer or the manufacturer for replacement
manuals or decals.
•Never use a machine that does not have an operator’s manual
available. Learn and understand the safety signs and symbols on
the machine and the operator instructions before you begin to
use the machine.
•Wear personal protective equipment. Know and use the
protective equipment that is to be worn when operating or
servicing the machine. Hard hats, protective glasses and face
shields, protective shoes, gloves, reflector type vests, and ear
protection are types of equipment that may be required.
Prolonged exposure to loud noise can cause hearing damage.
•Never operate a mower while under the influence of drugs or
alcohol. These make reflexes slow and put you and others in
grave danger. Always make sure you have full concentration
while mowing.
•Adhere strictly to all regulations at the worksite pertaining to the
operation of this equipment.
•Always disengage power takeoff (PTO) when transporting or
traveling between work sites.
•Be prepared for emergencies. Have a first aid kit, fire
extinguisher and emergency contact information available at the
work site.
POWER UNIT SAFETY
•The operator must have sufficient knowledge in the care and
operation of the power unit (tractor) before connecting power unit
to mower. Read and understand power unit operator’s manual
before connecting mower.
•Power unit must be equipped with ROPS and seat belt. Foldable
ROPS must be secured in the upright position. Follow
recommendations of power unit manufacturer. Seat belt must be
worn at all times.
•Power unit must be equipped with a 1-3/8” 6 spline 540 RPM
PTO connection. Never use PTO adapters to connect
implements. Never connect mower driveline to 1000 RPM PTO.

TDR-X Operator’s Manual
10
OPERATING EQUIPMENT SAFELY
•Never allow persons to stand between power unit and mower
while backing power unit up to hitch the mower.
•Before hitching mower to power unit, place transmission in
neutral, set park brake, and turn engine off. Remove the ignition
key.
•Make sure locking collar on PTO shaft is properly locked. If the
PTO shaft comes off during operation, personal injury or
equipment damage could result.
•Tall grass can hide obstacles. Carefully walk the entire area to
be mowed beforehand. Look for debris, rocks, tree limbs etc. that
will damage or be thrown by the mower blades. Identify objects
that cannot be removed. Set mower cutting height to avoid
contact.
•Ensure that no bystanders are within 10 ft of mower when wing
transport locks are released.
•Keep all bystanders well away from the machine when it is
operating. Always maintain a safe operating distance from
personnel, other equipment, or vehicles.
•Never operate the mower with deflectors or guards removed.
Mower blades can cause small objects and debris to be thrown
from under the mower deck at high speeds, up to 300 ft away.
Objects ejected by the mower blades can cause severe injury.
•Never tamper with safety devices or operate the mower with
them removed. Check proper operation regularly.
•Always disengage PTO, place all controls in neutral, turn power
unit off, set parking brake, and remove key before dismounting,
for any reason.
•Never place hands or feet under mower deck when the mower is
operating, or power unit engine is running.
•Disengage the PTO when crossing gravel areas or roadways.
•Disengage the PTO and turn power unit off upon striking any
object. Inspect mower and repair any damage before continuing.
•If the equipment should start to vibrate abnormally during
operation, stop the mower, shut down power unit, and
immediately check for the cause. Excess vibration is generally an
indication of a problem. Replace bent or damaged parts, do not
attempt to straighten a bent blade.
•Use extreme care when operating on uneven terrain.
•Reduce speed when operating on slopes during wet conditions,
especially when making sharp turns.
•Do not use the mower in limited visibility (e.g. at dusk, in fog,
heavy rain etc.). Mow only in daylight or good artificial light.
•Disengage PTO and ensure blades are completely stopped
before raising wings.
•Ensure wing and deck safety locks are securely engaged before
transporting mower with wings in raised position.
•Mower is not intended for transport on public roadways.

TDR-X Operator’s Manual
11
•Before disconnecting from power unit, always lower equipment
to the ground, place controls in neutral, set park brake, turn
engine off, and wait for all moving parts to stop. Relieve hydraulic
pressure per power unit manufacturer’s instructions.
•Ensure mower tongue jack is securely fastened to mower frame
with supplied pin before removing hitch draw pin.
MAINTENANCE SAFETY PRECAUTIONS
•Never make adjustments or repairs with the engine running.
Always disengage PTO, engage parking brake, turn engine off,
lower wings to cutting position and relieve hydraulic pressure
before performing any maintenance.
•Observe and perform proper lock-out procedures for power unit
if attached to mower during service.
•Keep nuts and bolts tight and properly at the proper torque,
especially blade attachment bolts. Check that all cotter pins are
properly installed. Keep equipment in good condition.
•Keep mower free of grass, leaves, or other debris build-up.
•Never work on raised mower decks without safety locks in place.
•Periodically check condition of safety devices, guards, and
deflectors. Replace only with manufacturer’s recommended
parts.
•Inspect and replace damaged blades. Use only original OEM
parts. Blades can fail from poor maintenance practices.
•Handle mower blades carefully. They are sharp and can cut
unprotected skin. Use caution and wear gloves when handling
them.
•Check to make sure hydraulic hoses are not worn or damaged
and are routed to avoid chafing.
•Immediately replace any hydraulic hose that shows signs of
swelling, wear, leaks, or damage so it does not burst.
•Do not use your hand to check for hydraulic oil leaks. Use a piece
of cardboard instead. Hydraulic fluid escaping under pressure
can penetrate the skin causing serious injury. If skin penetration
occurs, seek medical attention immediately. Relieve all pressure
before disconnecting hoses.
•Do not bend or strike hydraulic lines, tubes, or hoses, or reinstall
them in a bent or damaged condition.
•Inspect tires daily for wear or damage. Check tire pressures
weekly with an accurate pressure gauge. Do not inflate tires
beyond 20 psi.
•Mounting and dismounting tires from rims can be dangerous and
should be performed by trained personnel using correct tools,
equipment, and procedures.

TDR-X Operator’s Manual
12
•Do not support the machine on cinder blocks, hollow tiles or other
members that may fail under continuous load.
•Never perform service on a machine that is supported solely by
a jack. Always ensure proper blocking is placed to support load
during service.
WELDING / GRINDING WORK PRECAUTIONS
IMPORTANT! A fire extinguisher should be easily accessible during all welding work.
Welding repairs are to be performed by a trained welder with proper
service instructions. Know the material to be welded and select the
correct welding procedure and materials (electrodes, rods, wire) that
will provide a weld metal strength equivalent to the parent material.
Move the machine to a clean, safe area before welding, grinding or
using a cutting torch on it. This type of work should only be done in a
clean area and not in places that contain combustible liquids, such as
fuel tanks, hydraulic pipes or similar.
Connect arc welder ground as close as possible to work area.
Work with extra care when welding, grinding or torch cutting near
flammable objects.
WORKING ON PAINTED SURFACES
Heated paint gives off poisonous gases. Therefore, paint must be
removed from an area with a radius of at least 4 in (10 cm) before
carrying out welding, grinding, or gas cutting. In addition to the health
hazard, the weld will be of inferior quality and strength if the paint is not
removed.
Methods and precautionary measures when removing paint:
Blasting –use respiratory protective equipment and protective
goggles.
Paint remover or other chemicals –use a portable air extractor,
respiratory protective equipment, and protective gloves.
Grinding –use a portable air extractor, respiratory protective
equipment, and protective gloves and goggles.
WORKING ON GALVANIZED / PLATED SURFACES
Only qualified welders should attempt a weld repair on galvanized or
plated components. Proper pre-welding surface preparation is
required.
Always ensure proper ventilation, wear proper respiratory protective
equipment and avoid direct contact with smoke emitted from the
welding process.

TDR-X Operator’s Manual
13
HYDRAULIC SYSTEM SERVICE PRECAUTIONS
Risk of personal injury! Wear safety glasses and use protective gloves.
Relieve all trapped pressure before performing any service to the
hydraulic system. Pressure can be maintained in the hydraulic circuits
long after the power source and pump have been shut down.
When servicing any hydraulic component of the mower ensure that all
decks and wings are in their lowered position and all hydraulic pressure
is relieved.
Tighten all connections before applying pressure.
It is important that each person who comes in contact with the machine
be alert to any faults.
Follow these basic precautions:
•Never adjust a pressure relief valve or other pressure-limiting
device to a higher pressure than specified.
•Check to make sure hydraulic hoses are not worn or damaged
and are routed to avoid chafing.
•When connecting mower to tractor ensure hydraulic hoses have
sufficient slack for negotiating turns and uneven terrain.
•Immediately replace any hydraulic hose that shows signs of
swelling, wear, leaks or damage so it does not burst.
•Do not use your hand to check for hydraulic oil leaks. Use a piece
of cardboard instead. Hydraulic fluid escaping under pressure
can penetrate the skin causing serious injury. If skin penetration
occurs, seek medical attention immediately. Relieve all pressure
before disconnecting hoses.
•Do not bend or strike high-pressure lines, tubes, or hoses, or
reinstall them in a bent or damaged condition.
HYDRAULIC OIL HANDLING PRECAUTIONS
Oils can irritate and damage the eyes, throat, and sensitive skin. Avoid
contact.
Petroleum based oils are hazardous to the environment. Take special
care not to spill or discharge these fluids. Use approved containers and
methods to handle and dispose of them.
Use an authorized disposal and recycling company.

TDR-X Operator’s Manual
14
SAFETY DECALS
If decals become faded, damaged, or lost, replace immediately. Order Decal Kit, Part
# 541503.
ITEM
NO.
DESCRIPTION
QTY
11
PROGRESSIVE
2
12
PTO –READ MANUAL
1
13
SAFETY SIGN - OUTER
GUARD
4
14
PTO ALIGNMENT
1
ITEM
NO.
DESCRIPTION
QTY
1
DANGER –READ MANUAL
1
2
WARNING-BLADE
HARDWARE
1
3
CAUTION –REPLACE
SHIELDS
8
4
COMPANY NAME
1
5
DANGER - BLADE HAZARD
7
6
WARNING –OEM PARTS
1
7
CAUTION –DISENGAGE PTO
1
8
PTO GREASING
9
NOTICE –HITCH SETUP
1
10
MOWER MODEL
2
1
8
3
4
5
9
11
10
6
2
7
12
13
14

TDR-X Operator’s Manual
15
DECAL LISTING
No. 1 - 209172
No. 5 - 209173
No. 3 - 209113
No. 8 - 526001
No. 6 - 209115
No. 7 - 209174
No. 9 - 521784
No. 12 - 210238
No. 13 - 210237
No. 15 - 521014
PROGRESSIVE
No. 11 - 209103
No. 4 - 521817
No. 2 - 209196
No. 10 - 209203
No. 14 - 209189

TDR-X Operator’s Manual
16
ASSEMBLY INSTRUCTIONS
Mower assembly must be completed by a qualified technician
using safe work practices and proper tools.
INPUT SHAFT –shipped strapped to wing deck swivel
1. Remove ½” UNC retaining bolt/nut from input shaft.
2. Remove notification tag from intermediate shaft hanger bearing.
IMPORTANT - Ensure gold colour spacer ring is present against bearing inner race.
3. Disconnect input shaft shield at clamp yoke end and
slide shield exposing the clamp yoke (see input shaft
service instructions in mower manual storage tube).
4. Place the Input shaft on the provided support.
5. Install input shaft clamp yoke on intermediate shaft,
ensuring gold coloured spacer ring is in place between
the input shaft yoke and hanger bearing race.
6. Reinstall ½” UNF retaining bolt in input shaft yoke,
torque to 85 ft-lb.
7. Reinstall input shaft shield per input shaft service
instructions.
8. Fasten input shaft guard retaining chain to mower main
frame.
If the PTO shaft comes off during operation, it may cause
personal injury and damage to the PTO shaft and tractor
PTO. When checking, make sure the locking collar is
locked, and that the shaft is not just jammed against the end
of the tractor PTO shaft.
SLIDE SHAFT
SHIELD BACK
INPUT PTO SHAFT
SUPPORT

TDR-X Operator’s Manual
17
Wing Deck PTO
Align Yokes
Wing Deck PTO
Align Yokes
INSTALLING DECK PTO SHAFTS:
The three deck PTO shafts are used to drive the mower decks. Each
PTO shaft will have one end designated a tractor end. This end should
be hooked up to the main gearbox.
The PTO shafts from the two wing decks must be timed / aligned when
mounted to the gearbox. See illustration below. Mount the one side first
with the yoke laying flat. The opposite side must be mounted with the
yoke laying as flat as possible. ie. Timed. Note it may not be possible
to engage the second PTO perfectly aligned to the first, due to
positioning of the internal gearing. Position as close as possible.
Front of TDR-X
All PTO shafts have a short chain attached on both ends. Find a location to wrap or hook on
short chain. Be sure that when decks are brought into transport position, the safety chain will
not bind or pull PTO shield.
The Intermediate shaft is installed with the large bell end onto the main
gear box. The PTO mount bracket is then installed by sliding the PTO
end through the flange bearing, leaving the mounting bolts loose. See
section on “Hitching to the Tractor

TDR-X Operator’s Manual
18
TRANSPORT TIRES
Check air pressure in the tires and adjust according to specifications
Transport Tires –20 PSI
The mower is now ready for pre-delivery inspection and lubrication prior
to first use.