PS EDGESAFE SG-60-PCY User manual

1
Smart Gate Series
Rev022520
© 2020 PS Industries®Incorporated. All Rights Reserved. PN 514187 B
Installation Instructions/Operation and Maintenance Manual
Patent Pending
Table of Contents:
Safety Precautions ............................................................. 2
Product Information ........................................................... 2
Installation Instructions..................................................... 4
Disassembling of Gate.....................................................12
Operation..........................................................................13
Replacement Parts List ...................................................14
Size Reference Drawing...................................................15
Inspection and Maintenance........................................... 16
Warranty Certicate .........................................................19
Models:
SG-60-PCY
*Refer to page 15 for required size dimensions.
Contact Information
Mail
PS Safety Access
1150 South 48th Street
Grand Forks, ND 58201
Website
pssafetyaccess.com
Email
[email protected]
Local Phone
701.746.4519
Toll Free Phone
877.446.1519
Hours of Operation
8 A.M. to 5 P.M. CT
Monday – Friday
IMPORTANT! Read entire Instruction and Operations Manual to become familiar with the product.
NOTICE This product is a fall protection product. The effectiveness of the product is directly related to the proper
installation and operation of this product. Failure to properly maintain this product will affect performance.
Publication Notice
This manual has been compiled and published covering the latest product descriptions and specications.
The contents of this manual and the specications of this product are subject to change without notice.
PS Safety Access™ reserves the right to make changes without notice in the specications and materials contained
herein and shall not be responsible for any damages (including consequential) caused by reliance on the materials
presented, including but not limited to typographical and other errors relating to the publication.
PS Safety Access and/or its respective suppliers may make improvements and/or changes in the product(s)/
service(s) offered and/or the program(s) at any time without notice.
Retain this manual for future reference.
If you would like to download a copy of this manual, please go to pssafetyaccess.com
Product registration is an essential step to protecting your product, register Online at
psindustries.com/contact/register-your-product/

2Smart Gate Series
Rev022520
© 2020 PS Industries®Incorporated. All Rights Reserved.
Safety Precautions
Product Information
The following icons are used throughout this Manual.
DANGER Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
WARNING Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
CAUTIONCAUTION Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderated injury.
NOTICE Indicates manufacturer’s statement of additional information.
IMPORTANT! Indicates a required action.
CRITICAL Indicates a vital component to product performance.
NOTICE Unauthorized modication of or to the Product voids this Limited Warranty. Authorized modications,
received in writing from PS Industries® Incorporated, as long as the modication is accomplished in strict
accordance with PS Industries’ instructions, does not void warranty. If this product is modied or altered
without manufactures permission, manufacturer is no longer responsible for the product design, engineering,
or performance and owner assumes all responsibility. To request product modications contact PS Industries
Incorporated, 1150 S. 48th Street, Grand Forks, ND 58201, phone [phone], email: [email protected]
I. General Information
A. This manual contains information regarding installation, operation, and maintenance of the PS Safety Access’
Smart Gate.
B. PS Safety Access recommends that the owner implement a regular preventative maintenance program to
inspect and maintain the Smart Gate at a minimum, in accordance with the recommendations in this manual.
II. Operation Guidelines
A. The Smart Gate is designed to meet OSHA Railing Standard 1910.29(b).
B. Operation in a manner other than intended could result in damage or less than acceptable performance at time
of need, for which the manufacturer will not be held responsible.
C. The SG-60-PCY is adjustable from a minimum of 48” to a maximum 78” clear opening. The Gate will t 48”,
54”, 60”, 66”, 72” and 78” doors.
III. Safety Precautions
A. Ensure opening is clear of all obstructions through the entire proposed travel of the Smart Gate during
operation.
B. Comply with all OSHA and ANSI Safety Regulations and/or company safety policies when installing.
DANGER Ensure area below installation is blocked off from personnel during installation, and mounting surface
is capable of supporting all loading. Structural analysis of mounting surface is the responsibility of the owner.
IMPORTANT! Verication of the structural sufciency of supplied anchors based on site specic conditions and the
existing structure is the responsibility of the installer/customer. Refer to the anchor manufacturer's installation
instructions for installation requirements.
IV. Storage Prior to Installation of Product
A. Store materials in a dry, ventilated location. If outdoor storage is required, block materials and tarp in a tent-like
arrangement, elevated above the product with open sides to allow airow.
V. Installation Site Preparation
NOTICE Before starting site preparation and installation of the Smart Gate, read the entire Operation and
Maintenance Manual and review all installation instructions thoroughly.
A. Clear work area of any debris.
B. Ensure you have the necessary tools available.
C. Obtain all required permits.

3
Smart Gate Series
Rev022520
© 2020 PS Industries®Incorporated. All Rights Reserved.
Product Information
8
5
6
4
3
2
1
D. Personnel: Determine the appropriate number of personnel required to perform installation and have them
readily available at the project site. (1-2 people recommended)
E. Ensure all installation personnel utilize appropriate fall protection equipment and procedures during
installation.
NOTE: Review inventory to ensure all parts are present for assembly/installation. Refer to part list below.
Smart Gate Part List
(As shipped)
ITEM # DESCRIPTION QTY
1 LDSG;GATE POST 1
2 LDSG;GATE CATCH 1
3 LDSG;ADJ CLEVIS PCY 1
4 LDSG;2" LIFT ARM 5FT 2
5 LDSG;1.75" LIFT ARM 5FT 2
6 LDSG;GATE END 1
7 PLUG;SQ TUBE 2" O.D. 2
8 LDSG;DAMPENER 5 W/ ENDS 1
9 SG;HARDWARE BAG 60 1
Recommended Tools:
1. Two (2) 9 /
16” Socket and Ratchets
2. Two (2) 1 /
2” Socket and Ratchets
3. Two (2) 7 /
16” Socket and Ratchets
4. One (1) Rubber Mallet
5. One (1) Tape Measure
6. One (1) 3 /
16” Allen Wrench
7
HARDWARE BAG
9
x1
x8
x4
x8 x2
x11
x1
x6
x2
x1
x2
x2
x2 x1
x1
x2
x2
x1
5

4Smart Gate Series
Rev022520
© 2020 PS Industries®Incorporated. All Rights Reserved.
Installation
Clearance opening measured
from inside edge of baseplate
to baseplate
CONCRETE FLOOR ANCHOR INFO:
MIN. 3000 PSI CONCRETE
4" MIN. CONCRETE THICKNESS
3" MIN. EDGE DISTANCE (ALL SIDES)
Step 1
Illustration
VI. Smart Gate Installation
NOTICE Refer to parts list on Page 3 for part item numbers and descriptions.
NOTICE Base plates are slotted to allow adjustment for alignment.
STEP 1. Mark holes for the Gate Post and anchor with concrete oor anchors. Measure and mark the center of the
wall opening, using the Gate Size Reference Table to assist in centering the gate on the wall opening. (Gate
Size Reference Drawing on Page 15).
Door Opening
this side of
Gate Post
SG SIZE REFERENCE TABLE
CLEAR OPENING WIDTHS CLEARANCE HEIGHT
SG-60-PCY* 48”, 54” 60”, 66”, 72”, OR 78” 94 1/4” - 124 1/4”
Red
Decal
1
9.5
*SG-60-PCY:
a. Adjustable from a minimum of 48” to a maximum 78” clear opening.
b. Gate will t 48”, 54”, 60”, 66”, 72” and 78” doors.
IMPORTANT! Follow Anchor Manufacturer's technical data manual/installation instructions for installation
requirements and proper installation procedures.
Field concrete foundation design and complete consolidation of concrete surrounding embedded
item(s) anchorage points NOT by PS Safety Access.

5
Smart Gate Series
Rev022520
© 2020 PS Industries®Incorporated. All Rights Reserved.
Installation
STEP 3. Use rubber mallet to gently hammer ange bearings into both sides of 2” Lift Arm.
a. Slide 2” Lift Arm (red decal) into Adjustable Clevis (red decal).
b. Insert 3/8” x 3” hex bolt and tighten 3/8” nylock nut.
Step 3
Illustration A
Step 3
Illustration B
STEP 2. Attach Adjustable Clevis (red decal) with (2) 3/8” x 4” hex bolts, (2) 3/8” nylock nuts, and (4) 3/8” at
washers.
a. Tighten bolts, bracket height will be adjusted later in installation steps.
Step 2
Illustration
1
39.10
9.3 9.2 9.2
9.1
4
9.11
9.3
Red
Decal
Red
Decal
Red
Decals
Red
Decal

6Smart Gate Series
Rev022520
© 2020 PS Industries®Incorporated. All Rights Reserved.
Installation
Desired Gate Width:
48”
54” 66”
60”
78”
72”
Step 5
Illustration A
Step 5
Illustration B
Both fasteners are required
to secure tubes together.
Step 4
Illustration A
Step 4
Illustration B
NOTICE The 1 3/4” Lift Arms have a series of pre-drilled holes to allow for adjustable gate width. See Size Reference
Table (page 4) to determine available width adjustment.
NOTICE To protect the Powder Coat nish, do not slide beyond desired length.
STEP 4. Slide 1 3/4” Lower Lift Arm (green decal) into 2” Lift Arm (red decal) to the desired gate width.
a. Insert 3/8” x 2 1/4” hex bolts aligning with pre-drilled holes and tighten 3/8” nylock nuts.
54
9.4
Green
Decal
9.6
STEP 5. Use rubber mallet to gently hammer ange bearings into both sides of 1 3/4” Lower Lift Arm.
a. Slide the Gate End (green decal) over the 1 3/4” Lower Lift Arm (green decal).
b. Insert 3/8” x 2 3/4” hex bolt and tighten 3/8” nylock nut.
5
9.1
9.3
9.8
6
Green
Decal
Green
Decals

7
Smart Gate Series
Rev022520
© 2020 PS Industries®Incorporated. All Rights Reserved.
Installation
Step 7
Illustration A
Step 7
Illustration B
Step 6
Illustration A
Step 6
Illustration B
STEP 6. Use rubber mallet to gently hammer ange bearings into both sides of 2” Upper Lift Arm.
a. Slide 2” Upper Lift Arm (red decal) into Adjustable Clevis (red decal) on Gate Post.
b. Insert 3/8” x 3” hex bolt and tighten 3/8” nylock nut.
4
9.1
9.11
9.3
Red
Decal
Red
Decals
STEP 7. Slide 1 3/4” Upper Lift Arm (blue decal) into 2” Lift Arm (red decal).
a. Insert 3/8” x 2 1/4” hex bolts and 3/8” nylock nuts at pre-drilled holes.
NOTICE To protect the Powder Coat nish, do not slide beyond desired length.
9.3
9.6
45

8Smart Gate Series
Rev022520
© 2020 PS Industries®Incorporated. All Rights Reserved.
Installation
Step 9
Illustration Leave 1/4”of space between Gate End and inside of Gate Catch.
TOP VIEW
Step 8
Illustration A
Step 8
Illustration B
NOTICE Base plates are slotted to allow adjustment for alignment.
STEP 9. Mark out holes for the Gate Catch and anchor with concrete oor anchors.
STEP 8. Use rubber mallet to gently hammer ange bearings into both sides of 1 3/4” Upper Lift Arm.
a. Slide the Gate End (blue decal) over the 1 3/4” Upper Lift Arm (blue decal).
b. Insert 3/8” x 2 3/4” hex bolt and tighten 3/8” nylock nut.
9.1
9.8
9.3
Blue
Decals
2
9.5

9
Smart Gate Series
Rev022520
© 2020 PS Industries®Incorporated. All Rights Reserved.
Installation
Location for sizes
48”, 54”, or 60”
Move here for sizes
66”, 72”, or 78”
Step 10
Illustration A
Step 10
Illustration B
Step 11
Illustration A
STEP 11. Slide Dampener Mount Link into slot in 1 3/4” Lift Arm.
a. Insert 3/8” x 2 1/4” hex bolt and tighten 3/8” nylock nut.
Step 11
Illustration B
STEP 10. Add bumpers to Lower Lift Arms at both locations and snug with 1/4” bolts and 1/4” nylock capped nuts.
NOTICE Do not over-tighten, bumper should be snug but not compressed.
9.9 9.9
9.12
9.17
9.17
9.12
9.18
9.13
59.13
9.3
9.6

10 Smart Gate Series
Rev022520
© 2020 PS Industries®Incorporated. All Rights Reserved.
Installation
Step 13
Illustration A
Step 13
Illustration B
Smart Gate Weights
SG-60-PCY 65 LBS
Step 12
Illustration
WARNING The Smart Gates are heavy, verify weights, and use appropriate lifting procedures and equipment.
STEP 12. Rotate gate to the open position (gate arms vertical). Remove Gate Post from concrete oor anchors
to free up the assembly, and lay on the ground in the extended position for improved access during
dampener installation.
NOTICE To protect the Powder Coat nish, lay on cardboard.
Shoulder Bolt
9.7
STEP 13. Install dampener rst into the Gate End with 3/8” shoulder bolt (Illustration A).
a. Insert 5/16” x 1” hex bolt and tighten 5/16” nylock nut into the Dampener Mount Link (Illustration B).
9.4
8
9.16
9.7
9.14
9.15

11
Smart Gate Series
Rev022520
© 2020 PS Industries®Incorporated. All Rights Reserved.
Installation
Step 16
Illustration
STEP 16. To ensure the gate opens to precisely 90°, the Adjustable Clevis needs to be set.
a. Loosen 3/8” hex bolts and nylock nuts in Adjustable Clevis.
b. Tip gate vertically to 90° and re-tighten 3/8” hex bolts and nuts.
Step 15
Illustration
INSTALLATION IS COMPLETE!
A
DETAIL A
Final operational location
STEP 14. Fully extend assembly upward, anchor Gate Post back onto the oor surface, and tip gate down into Gate
Catch. As the gate approaches fully closed, you should hear a loud noise of the dampener self-setting.
STEP 15. Visually verify that the dampener self-set into the appropriate location.
a. Insert 3/8” x 2 1/4” hex bolt and tighten 3/8” nylock nut.
DANGER Keep ngers clear of dampener pivot points, dampener is under high pressure.
8
9.3
9.6
9.13
NOTICE If preferred, remove colored circle decals once
gate is assembled.

12 Smart Gate Series
Rev022520
© 2020 PS Industries®Incorporated. All Rights Reserved.
Disassembling Gate Instructions
Step 1
Illustration
Step 4
Illustration
VII. Disassembling Gate Instructions
NOTICE Only complete depressurization process if disassembling Smart Gate.
DANGER System under high pressure. Refer to depressurization instructions in Operations and Maintenance
Manual before doing any maintenance on the gate.
STEP 1. With gate in the closed position (gate arms horizontal).
a. Remove 3/8” x 2 1/4” hex bolt and 3/8” nylock nut from Dampener Mount Link (as shown in Illustration).
STEP 5. Remove the 3/8” shoulder bolt from Dampener at Gate end.
IMPORTANT! RETURN TO INSTALLATION STEPS 13-15 TO INSTALL NEW DAMPENER, AS SHOWN IN THIS
OPERATIONS AND MAINTENANCE MANUAL.
STEP 2. Rotate gate to the open position (gate arms vertical) before proceeding with Step 3.
CAUTIONCAUTION High internal gate forces! Before removing Gate Post baseplate fasteners, the gate must be in the open
position (gate arms vertical) so the dampener is in a non-compressed state.
STEP 3. Remove Gate Post from concrete oor anchors to free up the assembly and lay on the ground to enable
access to the dampener.
STEP 4. Remove 5/16” x 1” hex bolt and 5/16”nylock nut from Dampener end.
DANGER Keep ngers clear of Dampener ends and dampener mount link.
NOTICE To protect the Powder Coat nish, lay on cardboard.
8
9.3
9.6
9.13
9.149.15

13
Smart Gate Series
Rev022520
© 2020 PS Industries®Incorporated. All Rights Reserved.
Operation
ADJUSTABLE TO FIT:
48”, 54”, 60”, 66”, 72” OR 78” DOORS (SG-60-PCY)
VIII. Operation
NOTICE For locking your Smart Gate in the closed position, call PS Safety Access at 877.446.1519 to order an Edge-
SafeTM Lockout Kit (part #514582).
Gate lifts vertically
a full 90° without
Pinch Points
Uniquely placed
Dampener is mounted
high up to prevent
potential Pallet and
Forklift damage Counter-balanced design to
enable easy, One-Handed
operation
Slam-proof Dampening
System allows for
smooth Gate operation

14 Smart Gate Series
Rev022520
© 2020 PS Industries®Incorporated. All Rights Reserved.
Replacement Parts List
IX. Replacement Parts List
Replacement Parts List
ITEM # DESCRIPTION QTY PART #
1 LDSG;GATE POST PCY 1 513414
2 LDSG;GATE CATCH PCY 1 513424
3 LDSG;ADJ CLEVIS PCY 1 513420
4LDSG;2” LIFT ARM 5FT PCY 2514158
5LDSG;1.75” LIFT ARM 5FT PCY 2514160
6 LDSG;GATE END PCY 1 513437
7 PLUG; SQ TUBE 2" OD 2 513134
8 LDSG;DAMPENER 5 W/ ENDS 1 514163
9 SG;HARDWARE BAG 60 1 514648
9.1 BEARING;FLANGE .3765IDX.5030OD 8 514702
9.2 WASHER;FLAT 3/8” 16 ZN 4501947
9.3 NUT; NYLOCK 3/8” 16 ZN 11 501120
9.4 NUT;NYLOCK 5/16”18 HEAVY ZN 1 513780
9.5 ANCHOR;PWRSTUD+SD1-3/8”X3”CS 8 513454
9.6 BOLT; HEX 3/8” 16X2 1/4GR5ZN 6 500405
9.7 BOLT;SHOULDER3/8”X2-1/4” 1513779
9.8 BOLT; HEX 3/8” 16X2 3/4 GR5ZN 2 500406
9.9 BOLT; HEX 1/4” 20X3 1/2 GR5ZN 2 502651
9.10 BOLT;HEX3/8”16X4 GR5ZN 2 502859
FINISH OPTIONS
PCY Powder Coat Safety Yellow
For EdgeSafeTM Lockout Kit order (part #514582.) Kit includes (1)Storage
Bracket, (1)Lock Pin, (2)Bolts, (2) Nylock Nuts, and Installation Instructions.
TO ORDER PARTS CONTACT PS SAFETY ACCESS AT
877.446.1519 or [email protected]
13
NOTE 1. This replacement parts list and diagram is for the EdgeSafe™ SG-60-PCY Model.
Replacement Parts List
ITEM # DESCRIPTION QTY PART #
9.11 BOLT; HEX 3/8” 16X 3GR5ZN 2 500411
9.12 BUMPER;ROUND 1-1/2”DIAX1-1/2 2513133
9.13 LDSG;DAMPENER MOUNT LINK SS 1 514162
9.14 BOLT;HEX5/16”18X1GR5ZN 1 500422
9.15 NUT;NYLOCK 5/16”18 ZN 1 501126
9.16 SPACER;NYLON .406 X .625 X .60 2 514165
9.17 NUT;NYLOCK 1/4”20 ZN NYL CAP 2514472
9.18 WASHER;NYLON .274X.1.75X.25 1 514164
10 DECAL;LDSG, SG, & MG DANGER 2 513488
11 DECAL;LDSG MARKETING 2 513489
12 DECAL;LDSG THIS SIDE UP 2 513490
13 LDSG; WARNING LABEL 1 51 3745
1
11
12
10
9.18
9.17
9.12
9.9
9.16
9.15
9.14
9.13
9.6
9.3
7
8
9.7
9.8
9.11
9.10
9.2
9.3
9.5
9.4
9.1
9.2
9.3
3
26
9.1
9.3
9.1
4
5

15
Smart Gate Series
Rev022520
© 2020 PS Industries®Incorporated. All Rights Reserved.
SG Size Reference Drawing
21”
42”
Clearance
Height
CLEAR OPENING
8”
8”
8”8”
X. SG Size Reference Drawing
SG Size Reference Table
CLEAR OPENING WIDTHS CLEARANCE HEIGHT
SG-60-PCY 48”, 54”, 60”, 66”, 72”, OR 78” 94 1/4” - 124 1/4”

16 Smart Gate Series
Rev022520
© 2020 PS Industries®Incorporated. All Rights Reserved.
Inspection and Maintenance
XI. Inspection and Maintenance (Minimum Annually)
IMPORTANT! Consult parts list before replacing fasteners, as all have specic design load requirements. Only use
like items for replacement.
A. Gate:
1. Inspect components for damage and misalignment. Adjust, repair, or replace as needed, to meet original
design tolerance.
2. Check for proper alignment with catch. Adjust as necessary to achieve proper alignment.
3. Dampeners are maintenance free, replace dampener if assisting force has diminished.
4. Inspect bumpers for damage or wear, replace as needed.
B. Fasteners and mechanical connections:
1. All fasteners must be in place and adjusted to their original design standard. Replace any damaged
components.
2. Check all mounting connections, making sure they meet original design standards (refer to instructions).
3. If gate closes too quickly, fasteners at four corners of the gate can be tightened to reduce closing speed.
4. If gate closes too slowly, fasteners at four corners of the gate can be loosened to increase closing speed.
C. Finishes:
1. Inspect and clean nishes periodically.
2. Touch up repair nishes, or renish as necessary to protect the structural integrity of the Smart Gate.
3. The PCY Smart Gate comes with a polyester powder coat nish. Use nish materials compatible with powder
coat. Follow paint manufacturers’ instructions for prep and touch-up.
D. Housekeeping:
1. To ensure your product continues to operate and last, upon completion of proper installation, complete the
following:
a. Clean all surfaces.
b. If project is ongoing, protect installed products until nal completion of project.
c. Touch-up, repair, or replace damaged components.
2. Ensure the horizontal bars are clear of debris and interferences.
E. Labels and Placards:
1. Inspect all labels and placards.
2. Replace any labels and placards which are unreadable/missing.

17
Smart Gate Series
Rev022520
© 2020 PS Industries®Incorporated. All Rights Reserved.
Inspection and Maintenance Log CRITICAL Periodic Inspection and Maintenance Required. Inspect at minimum annually. Date Installed: Product: Model Number: Serial Number:
Opening Identier/ Number: Location:
DATE
INSPECTED
INSPECTED BY
(Print & Sign)
INSPECTION ITEMS
NOTED CORRECTIVE ACTION CORRECTED BY
(Print & Sign)

18 Smart Gate Series
Rev022520
© 2020 PS Industries®Incorporated. All Rights Reserved.
Inspection and Maintenance Log CRITICAL Periodic Inspection and Maintenance Required. Inspect at minimum annually. Date Installed: Product: Model Number: Serial Number:
Opening Identier/ Number: Location:
DATE
INSPECTED
INSPECTED BY
(Print & Sign)
INSPECTION ITEMS
NOTED CORRECTIVE ACTION CORRECTED BY
(Print & Sign)

19
Smart Gate Series
Rev022520
© 2020 PS Industries®Incorporated. All Rights Reserved.
Rev. 102119
PS INDUSTRIES® INCORPORATED – LIMITED WARRANTY
Limited Warranty: Subject to the terms of this Limited Warranty, PS Industries® Incorporated warrants to the original user or consumer (the
“Owner”) of a PS Industries product (the “Product”) that, for a period of one (1) year from date of shipment, the Product will be free from defects
in material and workmanship under normal use and service, and provided the Product is installed, operated and maintained in accordance with
instructions supplied by PS Industries. The terms and limitations of this Limited Warranty apply to all repaired or replacement Products for a term
equal to the balance of the warranty remaining on the Product that was repaired or replaced as of the date of such repair or replacement. Register
online at: www.psindustries.com/contact/register-your-product
PS Flood BarriersTM Product Warranty Registration: For PS Flood BarriersTM Products, this Limited Warranty will only be valid if the Owner
completes the Warranty Registration Form provided within thirty (30) days of Product installation. To request a copy of the Warranty Registration
Form, contact PS Industries Incorporated, 1150 S. 48th Street, Grand Forks, ND 58201, phone [phone], email: [e-mail].
Register online at: www.psindustries.com/contact/register-your-product/ Additional Warranty Registration Forms can be downloaded at
www.psfloodbarriers.com/download-center/
Warranty Exclusions: Notwithstanding anything to the contrary, this Limited Warranty does not cover any of the following:
1. Normal wear and tear (including, but not limited to, normal wear and tear to gaskets and weather seals); damage or accidents resulting
from freight damage, from failure to follow precautionary safety measures, or applied paint failure; abuse, misuse or unauthorized
modification of the Product; misapplication; improper installation; or any defects, damage or other harm that is not the result of the
acts or omissions of PS Industries.
2. Cost of field labor or other charges incurred by Owner in removing and/or re-affixing the Product or any part or component thereof.
3. Transportation costs.
Unauthorized modification of or to the Product voids this Limited Warranty. Authorized modifications, received in writing from PS Industries, as
long as the modification is accomplished in strict accordance with PS Industries’ instructions, does not void warranty. To request product
modifications contact PS Industries, 1150 S. 48th Street, Grand Forks, ND 58201, phone [phone], email: [e-mail].
Claim Procedure: To make a claim under this Limited Warranty, the claim must be received by PS Industries before the expiration of the above
stated Limited Warranty period together with proof of purchase. Contact PS Industries at the address shown below.
PS Industries Incorporated Toll Free: 877-446-1519
Attention: Warranty Phone: [phone]
1150 S. 48th Street Fax: [phone]
Grand Forks, ND 58201 E-mail: [e-mail]
An authorized PS Industries representative must be given a reasonable opportunity to inspect and investigate the alleged Product defect prior to
any work being done that affects the Product or its installation. PS Industries reserves the right to charge reasonable amounts for travel and labor
associated with investigation of claims. PS Industries may also require photographs of the alleged Product defect or return of the Product or part
to a designated PS Industries location, freight prepaid. A return goods authorization must be received prior to the return of the Product or part.
Please contact PS Industries to determine the designated location for return and to obtain the return material authorization.
Exclusive Remedy: In the event of a warranty claim that PS Industries determines to be covered by this Limited Warranty, PS Industries will
replace or repair, at PS Industries’ discretion, the Product or any part of the Product found to be defective.
Disclaimers: The above warranty and remedy is the sole express warranty and remedy given by PS Industries on its Product. No warranties or
representations at any time made by any representative from PS Industries shall vary or expand the provisions hereof. TO THE EXTENT PERMITTED
BY LAW, ALL EXPRESS AND IMPLIED WARRANTIES (INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE AND NON-INFRINGEMENT) OTHER THAN THE EXPRESS LIMITED WARRANTY SET FORTH ABOVE ARE EXPRESSLY DISCLAIMED. UPON THE
EXPIRATION OF THE ABOVE STATED LIMITED WARRANTY PERIOD, ANY AND ALL APPLICABLE IMPLIED WARRANTIES, INCLUDING, WITHOUT
LIMITATION, WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT, ARE DISCLAIMED. SOME
STATES DO NOT ALLOW LIMITATION ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO OWNER.
LIABILITY LIMITATION: In no event will PS Industries’ liability to Owner or any other person or entity exceed the price paid to PS Industries for
the defective Product. IN NO EVENT SHALL PS INDUSTRIES BE LIABLE TO OWNER OR ANY OTHER PERSON OR ENTITY FOR INCIDENTAL,
CONSEQUENTIAL, INDIRECT OR SPECIAL DAMAGES OF ANY DESCRIPTION, WHETHER ARISING OUT OF WARRANTY (INCLUDING ANY IMPLIED
WARRANTIES) OR ANY OTHER CONTRACT, STRICT LIABILITY, NEGLIGENCE OR OTHER TORT, OR OTHERWISE, INCLUDING ARISING FROM
INSPECTION OR REMEDY DELAYS. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES,
SO THE ABOVE LIMITATION AND EXCLUSION MAY NOT APPLY TO OWNER.
THIS WARRANTY GIVES OWNER SPECIFIC LEGAL RIGHTS AND OWNER MAY ALSO HAVE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE.

877.446.1519
[email protected] | pssafetyaccess.com
1150 South 48th Street | Grand Forks, ND 58201
Product Registration:
psindustries.com/contact/register-your-product