PS Safemezz MGH Series Operation and maintenance manual

1
MGH Series - Manual
Rev030921
© 2021 PS Industries®Incorporated. All Rights Reserved.
Installation Instructions/Operation and Maintenance Manual
Models:
Manual Models
Table of Contents:
Safety Precautions ............................................................. 2
Product Information ........................................................... 2
Installation Instructions..................................................... 4
Installation of Optional Face Mount Track......................11
Replacement Parts List ...................................................13
Replacement Parts Diagram ...........................................14
Inspection and Maintenance...........................................15
Training and Operation Instructions ............................... 17
Warranty Certicate .........................................................19
IMPORTANT! Read entire Instruction and Operations Manual to become familiar with the product.
NOTICE This product is designed to work with the EdgeSafe® Single Gates. The effectiveness of the product is
directly related to the proper installation and operation of this product. Failure to properly maintain this product will
affect performance.
Publication Notice
This manual has been compiled and published covering the latest product descriptions and specications.
The contents of this manual and the specications of this product are subject to change without notice.
PS Safety AccessTM reserves the right to make changes without notice in the specications and materials contained
herein and shall not be responsible for any damages (including consequential) caused by reliance on the materials
presented, including but not limited to typographical and other errors relating to the publication.
PS Safety Access and/or its respective suppliers may make improvements and/or changes in the product(s)/
service(s) offered and/or the program(s) at any time without notice.
Retain this manual for future reference.
If you would like a copy of this manual, please send an email to 4psinf[email protected]
Product registration is an essential step to protecting your product, register Online at
psindustries.com/contact/register-your-product/
Mail
PS Safety Access
1150 South 48th Street
Grand Forks, ND 58201
Website
pssafetyaccess.com
Email
[email protected]
Local Phone
701.746.4519
Toll Free Phone
877.446.1519
Hours of Operation
8 A.M. to 5 P.M. CT
Monday – Friday
Contact Information

2MGH Series - Manual
Rev030921
© 2021 PS Industries®Incorporated. All Rights Reserved.
Product Information
The following icons are used throughout this Manual.
DANGER Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
WARNING Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
CAUTIONCAUTION Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderated injury.
NOTICE Indicates manufacturer’s statement of additional information.
IMPORTANT! Indicates a required action.
CRITICAL Indicates a vital component to product performance.
Safety Precautions
NOTICE Unauthorized modication of or to the Product voids this Limited Warranty. Authorized modications,
received in writing from PS Industries® Incorporated, as long as the modication is accomplished in strict
accordance with PS Industries’ instructions, does not void warranty. If this product is modied or altered
without manufactures permission, manufacturer is no longer responsible for the product design, engineering,
or performance and owner assumes all responsibility. To request product modications contact PS Industries
Incorporated, 1150 S. 48th Street, Grand Forks, ND 58201, phone [phone], email: 4psinf[email protected]
I. General Information
A. This manual contains information regarding installation, operation, and maintenance of the PS Safety Access’
SafeMezz®Horizontal Gate.
B. PS Safety Access recommends that the owner implement a regular preventative maintenance program to
inspect and maintain the Horizontal Gate at a minimum, in accordance with the recommendations in this
manual.
II. Operation Guidelines
A. The Horizontal Gate is designed to meet:
1. OSHA Railing Standard 1910.28 and OSHA 1910.29.
B. Operation in a manner other than intended could result in damage or less than acceptable performance at time
of need, for which the manufacturer will not be held responsible.
III. Safety Precautions
A. Ensure opening is clear of all obstructions through the entire proposed travel of the Horizontal Gate during
operation.
B. Comply with all OSHA and ANSI Safety Regulations and/or company safety policies when installing.
DANGER If installed on edge, ensure area below installation edge is blocked off from personnel during
installation.
CAUTIONCAUTION For products that are approved for use as a means of fall protection, the product only serves as a
means of fall protection when the product is in the closed and latched position. In applications where the product
is positioned to protect a fall-edge, the person operating the product is required to implement another primary
means of fall protection, whenever the product is not closed and latched.
IMPORTANT! Due to variances in eld conditions, it is the responsibility of the installer to ensure that the product
is installed to mounting structure that is capable of supporting all imposed loading from the product. The installer
is responsible for ensuring that the provided fastening hardware or eld congured mounting arrangement is
capable of supporting all eld loads and meets applicable codes and regulations.
IV. Storage Prior to Installation of Product
A. Store materials in a dry, ventilated location. If outdoor storage is required, block materials and tarp in a tent-like
arrangement, elevated above the product with open sides to allow airow.
V. Installation Site Preparation
NOTICE Before starting site preparation and installation of the Horizontal Gate, read the entire Operation and
Maintenance Manual and review Approved for Construction Drawings and all additional installation instructions
thoroughly.

3
MGH Series - Manual
Rev030921
© 2021 PS Industries®Incorporated. All Rights Reserved.
Product Information
A. Clear work area of any debris.
B. Ensure you have the necessary tools available.
C. Obtain all required permits.
D. Personnel: Determine the appropriate number of personnel required to perform installation and have them
readily available at the project site (2-3 personnel recommended).
E. Ensure all installation personnel utilize appropriate fall protection equipment and procedures during
installation.
VI. Recommended Equipment and Tools for Installation:
A. Equipment for Face Mount Systems:
1. Scaffolding or Personnel Lift
B. Tools:
1. One (1) Drill for Anchoring
2. One (1) Phillips Screwdriver
3. One (1) Pliers
4. One (1) 9/
16” Wrench
5. One (1) 1/
2” Wrench
6. One (1) 7/
16” Wrench
7. One (1) Tape Measure
8. One (1) Level
9. Depending on type of anchors/fasteners, additional tools may be required.
VII. Horizontal Gate Parts List
A. Review inventory to ensure all parts are present for assembly/installation. Refer to parts list below.
SafeMezz Horizontal Gate Part List
ITEM # DESCRIPTION QTY
1 MGH;TRACK ASSEMBLY-PCY 1
2 MGH;SHROUD ASSEMBLY-PCY 1
3 MGH;GATE ASSEMBLY-PCY 1
4 TRACK SHROUD HARDWARE KIT 1
5 GATE HARDWARE KIT 1
6 MANUAL LATCH HARDWARE KIT 1
7 FACE MOUNT TRACK KIT* 1
*Required for Face Mount locations only!
1
2
3
7
TRACK SHROUD KIT
4
MANUAL LATCH KIT
6
GATE KIT
5

4MGH Series - Manual
Rev030921
© 2021 PS Industries®Incorporated. All Rights Reserved.
Installation
SLIDE DIRECTION:
RIGHT
Step 1
Illustration I
Slide
SLIDE DIRECTION:
LEFT
Step 1
Illustration II
Slide
View from
Ground Level
View from
Ground Level
VIII. Horizontal Gate Installation
A. Refer to replacement parts list on Page 13 and 14 for part item numbers and descriptions.
B. Colored circle decals are provided for easier installation, remove once installation is complete.
STEP 1. Determine your Slide Direction.
a. Look up at the mezzanine deck from the ground level to determine what slide direction will be needed.
1). Slide Direction RIGHT: install your gate assembly using the holes marked with green decals.
2). Slide Direction LEFT: install your gate assembly using the holes marked with blue decals.
CRITICAL Your gate should open in the direction that allows the most side room for operation.
IMPORTANT! Installation steps are shown in SLIDE DIRECTION: LEFT from Deck Side. Install your gate assembly
using the hole locations marked with blue decals.
NOTICE Installation Step 2 located on Page 5 is for Deck Mount Locations ONLY. For Face Mount Installations refer
to Page 13 before continuing to Step 3.

5
MGH Series - Manual
Rev030921
© 2021 PS Industries®Incorporated. All Rights Reserved.
Installation
Step 2
Illustration I
Field Anchor
Step 3
Illustration I
(Shown as Slide Direction: LEFT)
DETAIL A
A
Fasteners
provided by
Installer
DETAIL B
Stop
Bracket
9
7
10
B
Line up
Edges
Operator Knockouts for use
on Electrical Gate only
View from
Mezzanine Deck
STEP 2. Installation of Track Assembly.
a. Line up leading edge of Track Assembly with leading edge of opening.
b. Field fasten Track Assembly to your existing structure using factory located holes. (Fasteners supplied by
the Installer.)
CRITICAL Ensure mounting surface is capable of supporting all loading. Structural analysis of mounting surface
is the responsibility of the Installer. Fasteners must be of sufcient size, grade, appropriate for anchoring
material, etc. to accept the potential loading. Consult qualied Structural Engineer.
STEP 3. Using supplied hardware from the Track Shroud Hardware Kit, begin assembling the Shroud Assembly
a. Install the Stop Bracket to farthest end of the Shroud Assembly using 1/
4” screws and ange nuts.

6MGH Series - Manual
Rev030921
© 2021 PS Industries®Incorporated. All Rights Reserved.
Gate Assembly
D
Installation
Step 5
Illustration I Blue
Decal
DETAIL D
11
12
13
Step 4
Illustration I
DETAIL C
Right Hand
Manual Latch
Assembly
19
4
5
C
Shroud Assembly
18
17
Blue
Decal
Lower
Hole
Location
Step 5
Illustration II
SLIDE DIRECTION: LEFT to open
Lower Hole Location
Upper Hole Location
Leading
End
Blue Decal
Blue Decal
STEP 4. Install Manual Latch Assemblies using supplied hardware from the Manual Latch Hardware Kit.
a. Attach both Manual Latch Assemblies (as shown) to the Shroud with supplied 5/
16” washers and nylock
nuts.
b. Adhere decals to top of Shroud above each latch assembly.
Left Hand
Manual Latch
Assembly
STEP 5. Install front wheel in the leading end of Gate Assembly using supplied clevis pin and cotter pin.
CRITICAL Front wheel MUST be in the lower hole location of leading end of Gate Assembly.
Leading
End

7
MGH Series - Manual
Rev030921
© 2021 PS Industries®Incorporated. All Rights Reserved.
Installation
Gate Assembly
E
Step 6
Illustration I
Guide Block
DETAIL E
15
5
4
STEP 6. Attach UHMW Gate Guide Block to top of Gate Assembly using 5/
16” carriage bolts, washers, and nylock
nuts.
a. The notch located in Guide Block MUST be orientated towards existing structure (refer to Detail F for
correct placement).
Gate Assembly
F
Step 6
Illustration II
Notch towards
Existing Structure
DETAIL F
Existing Structure
14
NOTICE Existing structure only shown for reference of notch direction.

8MGH Series - Manual
Rev030921
© 2021 PS Industries®Incorporated. All Rights Reserved.
Installation
Step 7
Illustration I
DETAIL G
G
16
15
5
4
Pull
Handle
STEP 7. Attach the Red Pull Handle Assembly to the Gate with 5/
16” carriage bolts, washers, and nylock nuts.
a. Handle MUST be installed on the trailing end of the Gate.
Trailing
End
STEP 8. Install Shroud Assembly to top of Track Assembly as shown.
a. Attach using supplied 3/
8” washers and nylock nuts from the Track Shroud Hardware Kit
Shroud
Assembly
Step 8
Illustration I
Track Assembly
DETAIL H
Step 8
Illustration II
H
Shroud
Assembly
1.4
1.3

9
MGH Series - Manual
Rev030921
© 2021 PS Industries®Incorporated. All Rights Reserved.
Installation
STEP 9. Slide Gate Assembly into Track and Shroud Assemblies.
a. Slide Gate to fully open position, Gate inside Track and Shroud Assemblies.
Shroud Assembly
Step 9
Illustration I
Track
Assembly
Shroud Assembly
I
SIDE VIEW
Step 9
Illustration II
DECK VIEW
(Shown as Slide Direction: LEFT)
Step 9
Illustration III
DETAIL I
Track Assembly
Gate Assembly
Slide
Slide

10 MGH Series - Manual
Rev030921
© 2021 PS Industries®Incorporated. All Rights Reserved.
Installation
Step 10
Illustration I
DETAIL J
8
6
10
J
Widest
Side of
Block
Vertical
Track
Support
Step 11
Illustration II
L
TOP VIEW
(Shown as Slide Direction: LEFT)
STEP 10. Attach Shroud Block to Track Shroud Assembly with 1/
4” screws and ange nuts.
a. Shroud Block MUST be installed on open edge of Shroud Assembly with the widest side orientated away
from the vertical track support (refer to Detail J for correct orientation).
DECK VIEW
(Shown as Slide Direction: LEFT)
STEP 11. Install Stop Jamb onto Existing Structure.
a. Keep Gate Assembly in the fully open position (Gate inside Track and Shroud Assemblies).
b. Field fasten Stop Jamb vertically (refer to Detail K and Detail L on Page 11 for correct dimensions).
(Fasteners supplied by the Installer.)
CRITICAL Ensure mounting surface is capable of supporting all loading. Structural analysis of mounting surface
is the responsibility of the Installer. Fasteners must be of sufcient size, grade, appropriate for anchoring
material, etc. to accept the potential loading. Consult qualied Structural Engineer.
Step 11
Illustration I
K
DECK FRONT VIEW
(Shown as Slide Direction: LEFT)

11
MGH Series - Manual
Rev030921
© 2021 PS Industries®Incorporated. All Rights Reserved.
Installation
DETAIL L
43 /
16”
Stop
Jamb
Field Fasten
DETAIL K
20”
11”
3
STEP 12. Verify Gate Assembly latches in both open and closed positions.
NOTICE If preferred, remove colored circle decals once Gate is fully assembled.
Step 12
Illustration I
FRONT VIEW
(Shown with Section Cuts)
Verify Gate Latch Assemblies
Operate in both Open and
Closed Positions
IX. Installation of Optional Face Mount Track
A. Recommended Equipment: Scaffolding or Personnel Lift.
B. Once steps have been completed, continue with Shroud Assembly Installation on Page 5.
DANGER OPENING MUST BE GUARDED OR INSTALLATION PERSONNEL MUST WEAR FALL PROTECTION
EQUIPMENT AND BE TIED OFF. DO NOT ALLOW PERSONNEL NEAR UNPROTECTED LEADING EDGE DURING
INSTALLATION!
IMPORTANT! Installation steps are shown in SLIDE DIRECTION: LEFT from Ground Side.
NOTICE Installation Steps located on Page 12 are for Face Mount Locations ONLY. For Deck Mount Installations
refer to Page 5.

12 MGH Series - Manual
Rev030921
© 2021 PS Industries®Incorporated. All Rights Reserved.
Installation
Step 1
Illustration I
DETAIL M
4”
1
/
4
”
M
Face Mount Track
Existing
Structure
20
GROUND VIEW
(Shown as Slide Direction: LEFT)
View from
Ground Level
N
Field
Anchor
Face Mount Track
GROUND VIEW
(Shown as Slide Direction: LEFT)
STEP 1. Installation of Face Mount Track.
a. Measure 4” beyond leading edge of opening and 1/4” below top of mezzanine deck (refer to Detail M for
proper dimensions).
b. Field fasten Face Mount Track to your existing structure. (Fasteners supplied by the Installer.)
CRITICAL Ensure mounting surface is capable of supporting all loading. Structural analysis of mounting surface
is the responsibility of the Installer. Fasteners must be of sufcient size, grade, appropriate for anchoring
material, etc. to accept the potential loading. Consult qualied Structural Engineer.
STEP 2. Installation of Track Assembly.
a. Place Gate Housing Track on top of the Face Mount Track and line it up with the provided holes.
b. Attach Gate Housing Track with 5/
16” carriage bolts and nylock nuts.
c. Field fasten Gate Housing Track to your existing structure using factory located holes. (Fasteners
supplied by the Installer.)
CRITICAL Ensure mounting surface is capable of supporting all loading. Structural analysis of mounting surface
is the responsibility of the Installer. Fasteners must be of sufcient size, grade, appropriate for anchoring
material, etc. to accept the potential loading. Consult qualied Structural Engineer.
1.1
22
DETAIL N
4”
1
/
4
”
21
View from
Ground Level
Step 2
Illustration I

13
MGH Series - Manual
Rev030921
© 2021 PS Industries®Incorporated. All Rights Reserved.
Replacement Parts List
XII. Replacement Parts List
A. This Replacement Parts List is for all SafeMezz® Horizontal Gate Manual Models.
B. The Replacement Parts Diagrams are located on Page 14.
FINISH OPTIONS
PCY Powder Coat Safety Yellow
TO ORDER PARTS CONTACT PS SAFETY ACCESS AT
877.446.1519 or [email protected]
Replacement Parts List
ITEM # DESCRIPTION QTY PART #
1 REFER TO HARDWARE VARIANT
1.1 REFER TO HARDWARE VARIANT
1.2 REFER TO HARDWARE VARIANT
1.3 WASHER;FLAT 3/8” ZN 6 501947
1.4 NUT;NYLOCK 3/8”16 ZN 6 501120
2 REFER TO HARDWARE VARIANT
3 MGH;STOP JAMB PCY 1 511503
4 NUT;NYLOCK 5/16”18ZN 10 501126
5 WASHER;FLAT 5/16” ZN 8 501949
6 MGH;SHROUD BLOCK 1 511489
7 MGH;STOP BRACKET PCY 1 511504
8 SCREW;PANPHMACH1/4”20X1 3/4ZN 2 501507
9 SCREW;PANPHMACH1/4”20X1/2ZN 2 501509
10 NUT;FLANGE 1/4”20ZN-CASE HARD 4 501084
11 PIN;CLEVIS 1/2”X2-1/4”, ZN 2 509178
12 SHEAVE;UHMW,BLACK,1-3/4” DIA 2 501555
13 PIN;COTTER 1/8x 3/4 ZN 2 503403
14 MGH;UHMW GATE GUIDE BLOCK 1 511500
15 BOLT;CARRIAGE5/16”18X2-1/4”GR5 4 506502
16 MGH;ROUND PULL HANDLE PCR 1 511496
17 MGH;MANUAL LATCH ASSEMBLY LH 1 511517
18 MGH;MANUAL LATCH ASSEMBLY RH 1 511970
19 DECAL;MHM LATCH WARNING 2 512839
*20 REFER TO HARDWARE VARIANT
*21 REFER TO HARDWARE VARIANT
*21 REFER TO HARDWARE VARIANT
Hardware Variant for MGH-72-PCY
ITEM # DESCRIPTION QTY PART #
1 MGH;TRACK SHROUD ASSEMBLY-PCY-72” 1 513903
1.1 MGH;TRACK ASSEMBLY-PCY-72” 1 512368
1.2 MGH;SHROUD ASSEMBLY-PCY-72” 1 512371
2 MGH;72” GATE ASSEMBLY-PCY 1 511699
Hardware Variant for MGH-96-PCY
ITEM # DESCRIPTION QTY PART #
1 MGH;TRACK SHROUD ASSEMBLY-PCY-96” 1 513904
1.1 MGH;TRACK ASSEMBLY-PCY-96” 1 512374
1.2 MGH;SHROUD ASSEMBLY-PCY-96” 1 512377
2 MGH;96” GATE ASSEMBLY-PCY 1 511702
Hardware Variant for Face Mount MGH-96-PCY
ITEM # DESCRIPTION QTY PART #
*20 MGH;FACE MOUNT TRACK-PCY-96” 1 512385
*21 BOLT;CARRIAGE 5/16”X3/4”GR5 2 514333
*22 NUT;NYLOCK 5/16”18 ZN 2 501126
Hardware Variant for Face Mount MGH-72-PCY
ITEM # DESCRIPTION QTY PART #
*20 MGH;FACE MOUNT TRACK-PCY-96” 1 512381
*21 BOLT;CARRIAGE 5/16”X3/4”GR5 2 514333
*22 NUT;NYLOCK 5/16”18 ZN 2 501126
*Required for Face Mount location only!

14 MGH Series - Manual
Rev030921
© 2021 PS Industries®Incorporated. All Rights Reserved.
Replacement Parts Diagram
XIII. Replacement Parts Diagram
A. These Replacement Parts Diagrams for all SafeMezz® Horizontal Gate Manual Models.
B. The Replacement Parts List is located on Page 13.
DETAIL Q
13
OP
Q
DETAIL PDETAIL O
12
11
3
2
1.2
1.1
17 18
19 19
20
21
22
15
16
15
14
9
7
10
5
4
5
4
10
6
8
1.3
1.4

15
MGH Series - Manual
Rev030921
© 2021 PS Industries®Incorporated. All Rights Reserved.
Inspection and Maintenance
Recommended Preventative Maintenance
ITEM FREQUENCY ITEM DESCRIPTION WHAT TO INSPECT STANDARD REPAIR ACTION
1 Each Use General Housekeeping Track and loading area.
Track and loading area must
be kept free of debris and
obstructions.
Always keep area clean.
2 Weekly Track Assembly Track Assembly is not bend,
broken, kinked, or dented.
Track must be straight, true, level,
and undamaged.
Replace or repair track to original
dimensions and congurations.
Track Assembly is not rusting or
corroded.
Minor surface rust/corrosion. No
Scaling or pitting of material.
Clean and touch up minor surface
rust. If rust scale or pitting is
present, replace track.
3 Weekly
Track Assembly Splice
Connection (Face
Mount Track)
Track Assembly splice fasteners
are snug tight.
Fasteners must be present and be
snug tight; connections pulled into
rm contact by the bolt, no gaps
between material.
Tighten fasteners to snug tight.
Replace any missing fasteners.
Track Assembly splice alignment. Track sections are aligned.
Align track components and
tighten fasteners at splice
location.
4 Weekly Shroud Assembly Ensure Shroud Assembly is not
bent, broken, kinked, or dented.
Shroud Assembly must be straight,
true, level, and undamaged.
Replace or repair shroud
to original dimensions and
congurations.
All fasteners connections are
snug tight.
Fasteners must be present and be
snug tight; connections pulled into
rm contact by the bolt, no gaps
between material.
Tighten fasteners to snug tight.
Replace any missing fasteners.
5 Weekly Shroud Block Ensure Shroud Block is in place
and undamaged. Present, unbroken and unworn. Replace shroud block.
Shroud Block fasteners
Fasteners must be present and be
snug tight; connections pulled into
rm contact by the bolt, no gaps
between material.
Tighten fasteners to snug tight.
Replace any missing fasteners.
6 Weekly Guide Block Ensure Guide Block is in place
and undamaged. In place, undamaged and unworn. Replace guide block.
Guide Block fasteners
Fasteners must be present and be
snug tight; connections pulled into
rm contact by the bolt, no gaps
between material.
Tighten fasteners to snug tight.
Replace any missing fasteners.
7 Weekly Manual Latch
Assemblies
Latch engages smoothly and
securely
Latching must operate with
minimal effort and positively hold
gate in position.
Repair or Replace component
immediately.
Pull Knob(s) in place Ensure components are present Repair or Replace component
immediately
Connector rod; not bent Ensure Pull Knob Connector Rod is
not bent or damaged.
Repair or Replace component
immediately
Latch spring engages Latch
Ensure Pull Knob/Connector Rod
spring is back into the locked
position.
Repair or Replace component
immediately
XIV. Inspection and Maintenance
A. Environmental conditional may affect the maintenance and repair requirements of the product, and
recommended preventative maintenance frequency.
B. If any of the inspection items are found to not meet the standard IMMEDIATELY “TAG OUT” the SafeMezz
Horizontal Gate removing it from active use and guard the opening until repairs are completed.
NOTICE PS Safety Access recommends that the owner implement a regular and preventative maintenance program
to inspect and maintain SafeMezz Horizontal Gate at a minimum, in accordance with the recommendations
in the table below.
WARNING While performing maintenance and inspection ensure personnel utilize appropriate fall protection
equipment and procedures. Manufacturer recommends utilizing a man-lift to perform maintenance and
inspection tasks.

16 MGH Series - Manual
Rev030921
© 2021 PS Industries®Incorporated. All Rights Reserved.
Recommended Preventative Maintenance Continued
ITEM FREQUENCY ITEM DESCRIPTION WHAT TO INSPECT STANDARD REPAIR ACTION
8 Weekly Pull Handle All fasteners
Fasteners must be present and be
snug tight; connections pulled into
rm contact by the bolt, no gaps
between material.
Tighten fasteners to snug tight.
Replace any missing fasteners.
Bent or damaged Pull Handle must be straight, true
and undamaged.
Repair or Replace component
immediately.
9 Weekly Gate Assembly Welds Welds intact without visible cracks
or crazing.
Repair or Replace component
immediately.
Ensure Gate Assembly is not
bent, broken, kinked, or dented.
Gate must be straight, true, and
undamaged.
Replace or repair gate to original
dimensions and congurations.
Gate is not rusting/corroded. Minor surface rust/corrosion. No
scaling or pitting of material.
Clean and touch up minor surface
rust. If rust scale or pitting is
present, replace gate.
10 Monthly Structural Attachment All fasteners (Structural
Attachment)
Fasteners must be present and be
snug tight; connections pulled into
rm contact by the bolt, no gaps
between material.
Tighten fasteners to snug tight.
Replace any missing fasteners.
11 Monthly Rollers Rollers
Minimal wear. No at spots. Roller
Flange undamaged and unbroken.
Fits Roller Pin snugly and rolls
smoothly.
Replace Rollers
12 Monthly Roller Clevis Pin Pin No wear. Smooth roller operation. Replace Roller Pin
Cotter Pin Cotter Pin in place. Prongs spread
in opposite directions 90 degrees. Replace or Re-spread Cotter Pin.
13 Monthly Decals/Labels All decals/labels Manufacturer's decals/labels in
place and legible.
Replace. Contact manufacturer for
FREE replacement decals/labels.
Inspection and Maintenance

17
MGH Series - Manual
Rev030921
© 2021 PS Industries®Incorporated. All Rights Reserved.
Training and Operating Instructions
XV. Training Instructions
A. PS Industries, Inc. recommends conducting formal operation training, and documenting the training, with
all personnel who will operate the product and who will be working in the area that the product is located.
Awareness of how the SafeMezz Horizontal Gate operates and the critical function it performs will improve
the likelihood that the product is respected and safely utilized.
B. The PS Industries, Inc. SafeMezz Horizontal Gate is simple yet critical piece of safety equipment in many
facilities. The SafeMezz Horizontal Gate, when in the closed and latched position, provides an effective
fall protection barrier for personnel. There are several critical components that work together to ensure
the SafeMezz Horizontal Gate will operate and perform the fall protection function. Key to performance
and longevity of the product are the Inspection and Maintenance recommendations contained in the O&M
Manual. The performance of the product is directly related to the proper operation and maintenance of the
product.
NOTICE Employers are responsible for providing supplemental training and guidelines specic to the Employer’s
facility, additional safety requirements and OSHA Regulations specic to the Employer’s industry and
specic facility safety policies. The manufacturer of the SafeMezz Horizontal Gate makes no claim to
know the specic Employer’s Safety Policies or other Regulatory Safety guidelines. Employer may need to
supplement or modify the training, inspection, maintenance, or operation instructions to meet additional
requirements.
XVI. Operating Instructions
CAUTIONCAUTION For products that are approved for use as a means of fall protection, the product only serves as a
means of fall protection when the product is in the closed and latched position. In applications where the product
is positioned to protect a fall-edge, the person operating the product is required to implement another primary
means of fall protection, whenever the product is not closed and latched.
NOTICE If you are placing material in the drop area to be retrieved by the forklift, place material prior to opening the
SafeMezz Horizontal Gate.
WARNING Always operate the manually operated SafeMezz Horizontal Gate from the Pull Handle.
A. Before Operation Checks:
1 The gate is NOT tagged-out for maintenance faults. TRUE FALSE
2 Track is clean and free of debris. TRUE FALSE
3 Upon visual inspection of the gate system, all components are in place. TRUE FALSE
4 Drop area is clean and free of debris or obstructions. TRUE FALSE
5 All personnel working in the area are WARNED of Gate Opening. TRUE FALSE
6 No personnel within 6 feet of opening. TRUE FALSE
WARNING If ANY Before Operation Checks are “FALSE” - DO NOT OPERATE!! Correct/Repair prior to operation.
B. Operation:
STEP 1. Pull upward on the Latch Release Knob to release the gate latch.
STEP 2. Utilizing the Red Pull Handle, walk the gate to the fully open position and ensure gate is latched. State at the
pull handle end of the gate.
WARNING DO NOT APPROACH THE OPEN LEADING EDGE.
WARNING DO NOT LEAVE OPEN GATE UNATTENDED.
STEP 3. When the material has been placed or removed from the drop area. Pull upward on the Latch Release Knob
to release the gate latch.
STEP 4. Utilizing the Red Pull Handle, walk the gate to the fully closed position and ensure the gate is latched.

18 MGH Series - Manual
Rev030921
© 2021 PS Industries®Incorporated. All Rights Reserved.
Training and Operating Instructions
C. During Operation Checks:
1 Latching operates smoothly and disengages/engages. TRUE FALSE
2 Gate rolls smoothly with minimal effort and, no binding. TRUE FALSE
3Gate is NOT impacted by the forklift, pallet jack, pallet, etc. TRUE FALSE
WARNING If ANY Before Operation Checks are “FALSE” - DO NOT OPERATE!! Correct/Repair prior to operation.
D. After Operation Checks:
1Any fault identied have been documented and reported to maintenance. TRUE FALSE
2If faults were identied, gate has been TAGGED OUT OF SERVICE and opening
has been protected until maintenance has corrected the fault. TRUE FALSE
WARNING DO NOT PROCEED TO THE LEADING EDGE OF THE GATE UNTIL GATE IS CLOSED AND LATCHED
STEP 5. Pull on the Red Pull Handle to verify the gate is latched in the closed position.
STEP 6. Visually verify that the gate is captured by the Stop Jamb.
STEP 7. Verbally announce to all personnel in the area that the gate is now closed and latched.

19
MGH Series - Manual
Rev030921
© 2021 PS Industries®Incorporated. All Rights Reserved.
Rev. 011221
PS INDUSTRIES® INCORPORATED – LIMITED WARRANTY
Limited Warranty: Subject to the terms of this Limited Warranty, PS Industries® Incorporated warrants to the original user or consumer (the
“Owner”) of a PS Industries product (the “Product”) that, for a period of one (1) year from date of shipment, the Product will be free from defects
in material and workmanship under normal use and service, and provided the Product is installed, operated and maintained in accordance with
instructions supplied by PS Industries. The terms and limitations of this Limited Warranty apply to all repaired or replacement Products for a term
equal to the balance of the warranty remaining on the Product that was repaired or replaced as of the date of such repair or replacement. Register
online at: www.psindustries.com/contact/register-your-product
PS Flood BarriersTM Product Warranty Registration: For PS Flood BarriersTM Products, this Limited Warranty will only be valid if the Owner
completes the Warranty Registration Form provided within thirty (30) days of Product installation. To request a copy of the Warranty Registration
Form, contact PS Industries Incorporated, 1150 S. 48th Street, Grand Forks, ND 58201, phone [phone], email: [e-mail].
Register online at: www.psindustries.com/contact/register-your-product/ Additional Warranty Registration Forms can be downloaded at
www.psfloodbarriers.com/download-center/
Warranty Exclusions: Notwithstanding anything to the contrary, this Limited Warranty does not cover any of the following:
1. Normal wear and tear (including, but not limited to, normal wear and tear to gaskets and weather seals); damage or accidents resulting
from freight damage, from failure to follow precautionary safety measures, or applied paint failure; abuse, misuse or unauthorized
modification of the Product; misapplication; improper installation; or any defects, damage or other harm that is not the result of the
acts or omissions of PS Industries.
2. Cost of field labor or other charges incurred by Owner in removing and/or re-affixing the Product or any part or component thereof.
3. Transportation costs.
Unauthorized modification of or to the Product voids this Limited Warranty. Authorized modifications, received in writing from PS Industries, as
long as the modification is accomplished in strict accordance with PS Industries’ instructions, does not void warranty. To request product
modifications contact PS Industries, 1150 S. 48th Street, Grand Forks, ND 58201, phone [phone], email: [e-mail].
Claim Procedure: To make a claim under this Limited Warranty, the claim must be received by PS Industries before the expiration of the above
stated Limited Warranty period together with proof of purchase. Contact PS Industries at the address shown below.
PS Industries Incorporated Toll Free: 877-446-1519
Attention: Warranty Phone: [phone]
1150 S. 48th Street Fax: [phone]
Grand Forks, ND 58201 E-mail: [e-mail]
An authorized PS Industries representative must be given a reasonable opportunity to inspect and investigate the alleged Product defect prior to
any work being done that affects the Product or its installation. PS Industries reserves the right to charge reasonable amounts for travel and labor
associated with investigation of claims. PS Industries may also require photographs of the alleged Product defect or return of the Product or part
to a designated PS Industries location, freight prepaid. A return goods authorization must be received prior to the return of the Product or part.
Please contact PS Industries to determine the designated location for return and to obtain the return material authorization.
Exclusive Remedy: In the event of a warranty claim that PS Industries determines to be covered by this Limited Warranty, PS Industries will
replace or repair, at PS Industries’ discretion, the Product or any part of the Product found to be defective.
Disclaimers: The above warranty and remedy is the sole express warranty and remedy given by PS Industries on its Product. No warranties or
representations at any time made by any representative from PS Industries shall vary or expand the provisions hereof. TO THE EXTENT PERMITTED
BY LAW, ALL EXPRESS AND IMPLIED WARRANTIES (INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE AND NON-INFRINGEMENT) OTHER THAN THE EXPRESS LIMITED WARRANTY SET FORTH ABOVE ARE EXPRESSLY DISCLAIMED. UPON THE
EXPIRATION OF THE ABOVE STATED LIMITED WARRANTY PERIOD, ANY AND ALL APPLICABLE IMPLIED WARRANTIES, INCLUDING, WITHOUT
LIMITATION, WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT, ARE DISCLAIMED. SOME
STATES DO NOT ALLOW LIMITATION ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO OWNER.
LIABILITY LIMITATION: In no event will PS Industries’ liability to Owner or any other person or entity exceed the price paid to PS Industries for
the defective Product. IN NO EVENT SHALL PS INDUSTRIES BE LIABLE TO OWNER OR ANY OTHER PERSON OR ENTITY FOR INCIDENTAL,
CONSEQUENTIAL, INDIRECT OR SPECIAL DAMAGES OF ANY DESCRIPTION, WHETHER ARISING OUT OF WARRANTY (INCLUDING ANY IMPLIED
WARRANTIES) OR ANY OTHER CONTRACT, STRICT LIABILITY, NEGLIGENCE OR OTHER TORT, OR OTHERWISE, INCLUDING ARISING FROM
INSPECTION OR REMEDY DELAYS. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES,
SO THE ABOVE LIMITATION AND EXCLUSION MAY NOT APPLY TO OWNER.
THIS WARRANTY GIVES OWNER SPECIFIC LEGAL RIGHTS AND OWNER MAY ALSO HAVE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE.

877.446.1519
[email protected] | pssafetyaccess.com
1150 South 48th Street | Grand Forks, ND 58201
Product Registration:
psindustries.com/contact/register-your-product