Pule 810621419 User manual

series. Therefore, if a bulb is pulled out, that series of bulbs will fail to light.
8. Replace failed bulbs immediately by the same
7. Do not place this set where it may become cover
6. Always unplug from the main power supply w
1. This product comes semi-assembled. Remove the
These instructions are for your safety. Please read through them thoroughly
before use and retain for future reference.
Safety Reminder:
•
This is not a toy. It’s a decoration only.
•
To protect against electric shock, never immerse any appliances, the main lead plug in water or any other
liquid. Also ensure hands are dry before operating and connecting/disconnecting the power source.
•
Always position cables and extension leads so that they will not be a hazard to the elderly, children and
pets.
•
Do not overload power sockets or extension leads.
•
If you are in any doubt about installing this product, consult a qualified electrician.
Warning: light set from the packaging. Take care not to
socket. If part of product or cable is damaged, the set must be destroyed.
hen not in use, overnight or if unattended.
ed by other items such as
damage or twist the cable.
2. Ensure that the cables are fully unwound before use. Avoid any damage to the wire insulation.
3. Do not connect product to the power supply while it’s in the packaging.
4. Do not connect this product electrically to another chain.
5. Do not carry the product by the cord or pull the cord to remove the plug or transformer from the
curtains, nets or
bedding. rated voltage and wattage provided with this light
set to prevent overheating.
Use Instructions:
1. This product is suitable for indoor use only.
2. Remove the light set from the packaging, take care not to damage or twist the wires.
3. Ensure that the cables are fully unwound before use.
4. Check the set before use for loose or damaged wiring and that all the bulbs are secure. If you are in
doubt, do not use the set.
5. This product operates with an indoor DC transformer supplied with the set.
6. Use only with the DC transformer supplied which confirms to safety requirement of UL standard.
7. Plug the product into the DC transformer supplied with the set.
8. Plug the DC transformer into the main socket outlet.
9. This product is parallel wired in 5 sections of 10 bulbs with each individual section being wired in
ASSEMBLY AND USER INSTRUCTION
ITM./ ART. :810621419
missing, loose or twisted incorrectly bulb and replace / insert it well.
the lights in that circuit may not light. In this event, you must test all bulbs in that circuit to find out the
This set is constructed in series. Therefore if a bulb is missing, loose or twisted incorrectly in the base,
Bulb replacement instructions:
This light set has push-in / pull-out type replaceable bulbs. Please read and follow these instructions
when changing a bulb.
To remove a bulb please open the button of lampholder first, grip plastic collar at the base of the bulb
between your thumb and forefinger, and pull out the failed bulb with the collar, taking care not to crush
the bulb. See figure 1.
To replace a bulb, ensure the bulb contacts are in the correct place and the bulb makes a good
connection.
•To avoid the risk of overheating a failed bulb must be replaced immediately with a bulb of the same
rated voltage and wattage.
•Always disconnect the light set from the power supply before removing any bulb.
•
Figure 1

50 lights set 1pcs spare bulbs included
2. Place the section 1 onto the MG O pot,
ASSEMBLY IN STRUCTIO N S:
120V~60Hz, 0.08A
50pcs x 3.0V, 20mA
Trouble shooting:
If the set fails to light, please check the following:
•Disconnect the set from the main power supply.
•Check the transformer for loose wires.
•Check that the remaining bulbs are correctly positioned in the lamp holders.
•Check the remaining bulbs to ensure that they are not faulty or broken.
Specification:
Low voltage light set
Item No.:
Tye ref.:
Bulb rating:
This instruction sheet should be retained
Product to transformer: 1.8m
For indoor use only.
as it contains important information.
Made in China ○
E
28V 0.107A
DC Transformer model: TS-3W28V
Rated input voltage:
Rated output voltage:
1. Unpack the package to find all the 5 parts:
MG O pot
Section 1
Section 2
Lamp holder
3. Screw the section 2 onto the section 1,
plug in end-to-end connection.
4. Screw the lamp holder onto the section 2,
plug in the end-to-end connection.
5. Plug in the adapter to a standard AC
LPG-70F5LW05
Screws
CUSTOMER SERVICE:
If none of the above steps corrects your problem, please contact the Customer Service
FOR CUSTOMER SERVICE CALL: 1-800-311-3324
Business Hours: Monday - Friday - 9:30 am - 4:00 pm EST
Department at Puleo International, Inc. following the steps as below:
and fix it tightly with 3 screws.
outlet for decoration.
1
2
3