Pyle PTC19LC User manual

eModel=PTC19LC
16:10 DIGITAL LCD-TV-Monitor
19" Hi-Definition LCD Flat Panel TV
OPERATING MANUAL
www.py|eaudJo.com

Contents
3
4.1 CONNECTION ANTENNAS 6
4.2 AV VIDEO INPUT DRAWING 6
4.3 S-VIDEO INPUT DRAWING 6
4.4 PC (VGA) CONNEXION DRAWING 7
Turning on and off TV
Select on screen language
Volume adjustment
How to adjust the OSD
Choosing a TV channel
Selecting input source
8
8
8
9
9
9
Picture menu options 10
Audio menu options 10
Setup menu options 11
Feature menu options 13
VGA menu options 15
YPbPr menu options 16
HDMI menu options 16
A Remote control instructions 18
B Battery Usage Caution 20
21
iliiiiiii!iiiiiliii!iiiiii!iiii!!!!i!!i!!i!!i!!i!!i!!i!!i!

Contents
21
22
iliiiiiii!ii_iiiliii!iiiiii!iiii!!!!i!!i!!i!!i!!i!!i!!i!!i!_

Pfeface
PREFACE
Thank you for buying this TV ! Please read this manual thoroughly before operating the monitor.
Make sure the monitor was not damaged in transit. Should the monitor is damaged, do no install
it and contact your dealer. Check that you have all the accessories according to the model.
SAFETY PRECAUTIONS
Preparation
Put the monitor on a stable surface.
Do not use the monitor with others fixations than those provided or
suggested by the manufacturer.
_0nin_umdi_t_l_e_10_m s_
2o° i_ ...........
!i.............
Do not place any material on the monitor.
Do not block or cover the ventilation openings on the monitor
If you have a wall mount, check that it is steady
Power source
The monitor must be plugged with a tension source of llO volts and GO Hz,
Connexion cables
Power cord and cables must be properly routed and protected to prevent
people from stepping on them and causing the monitor to fall.

Safe typreca udons
Heating sources and humidity
Keep the monitor dry and away from humidity.
Keep the monitor away from heat sources
Cleaning and maintenance
Unplug the monitor before cleaning it. Do not use solvents or liquids
to clean the monitor.
Only clean the monitor with a soft and dry cloth.
In case of troubleshooting, do not use spare parts other than those
suggested by
the manufacturer. Using inadequate spare parts can lead to electric
shocks, short-circuits fire or other incidents.
Departure in holidays
Unplug the LCD during lighting storms or when unused for long periods
of time.

Front, back, co/Tnections of LOD
Front, Back, Connections of LCD
Front View
Back View and Control Connections
i
IR ON'OFF LEI
1 RF IN
2 v iN
S-VIDEO
4 HDMI
5 VGA
6 PC AUDIO
7 Pr
8 Pb
9 Y
10 R IN
11 L IN
12 PHONE
1 3 DC iN
VGA S-VID EO RF iN
I I I I I I
13 12 11 10 9 8 7 6 5 4 3 2 1

Tvin@alldondrawings
TV INSTALLTION DRAWINGS
VHF ANTENNA VHF ANTENNA
I I
OUTDOOR _
ANTENNA
AMPLIFIER
INDOOR
ANTENNA
AMPLIFIER
POWER PLUG OF
ANTENNA
AMPLIFIER
75 OHM
ANTENNA
PLUG
To ensure good picture and sound, TV antenna system needs to be installed. The antenna system as
shown can be sourced from TV equipment shops, which will provide service for correct installation
and connection. After installation, insert the 75-ohm antenna plug into the antenna jack as showmln
case of signal of closed circuit TV,
@ @ @
VGA S-VIDE0 VIN RF IN
@ @ @
tII|
VGA S-VIDE0 V iN RF iN

Tv in stalltiondrawings
PC AUDIO VGA
VGA

Men u Opera tion
Basic operatie_
TURN ON LCD TV
1. Connecting to the AC input cable then press the main power switch to switch O N LC D TV. At this time the TV wilt enter
standby mode and indicator show red.
2. Use POWER button can turn ON LCD TV from standby mode.
TURN OFF LCD TV
1. Press POWER button or _ button on the remote control to enter standby mode. The indicator is red.
2. Usb_g main power switch turns off LCD TV completely.
NOTE: If you use your LCD TV for the first time, you should select the language which will be used for displaying menus
and indications.
• Press MENU to display the main menu.
• Press • /• repeatedly to select the SET MENU.
• Use4/ I_- and • /• toselect LANGUAGE.
• Press ,,I and P- buttontoselectyourdesired language.
• When you are satisfied with your choice, press the MENU
to exit.
1. Press VOL+/- to adjust the volume.
2. If you want to switch the sound OFF, press the MUTE _.
3. You can cancel this function by pressing MUTE or VOL+.

Menu Operation
- Press the MENU button to display the main menu.
- U se • /•/4/_-buttons to select and adjust the available menus.
1
The OSD (On Screen Display) function enables you to adjust the screen status conveniently since it provides
graphical presentation.
1. Using the CH+/CH- on the front panel or on the remote control.
•Press CN+ to increase channel number.
• Press CN - to decrease channel number.
2. Using 0-9 digital buttons and -/--button
You can select the channel number by pressing 0 to 9 or 4--.
3. Example:
• To select 1-digit channel (e.g. Channel 5): Press the 5 button.
• To select 2-digit channel (e.g. Channel 20): Press the -/-- button repeatedly to disptay -- then press 2, follow by 0.
• To select 3-digit channel (e.g. Channel 103): Press the 4-- button repeatedly to display -- then press 1,follow by 0,
follow by 3.
Note: After select the digit button, the digit will be memorized.
You can select the input source by pressing the INPUT on the remote control or on the front panel.
9