Qeedji TAB10s User manual
User manual
TAB10s
9.10.10 002N
TAB10s
8:30
2
Legal notice
TAB10s 9.10.10 (002N_en)
© 2022 Qeedji
Rights and Responsibilities
All rights reserved. No part of this manual may be reproduced in any form or by any means whatsoever. or by any means whatsoever without the
written permission of the publisher. The products and services mentioned herein may be trademarks and/or service marks of the publisher. or
trademarks of their respective owners. The publisher and the author do not claim any rights to these Marks.
Although every precaution has been taken in the preparation of this document, the publisher and the author assume no liability for errors or
omissions, or for damages resulting from the use of the information contained in this document or the use of programs and source code that can go
with it. Under no circumstances can the publisher and the author be held responsible for any loss of profits or any other commercial prejudice caused
or alleged to have been caused directly or indirectly by this document.
Product information
Product design and specifications are subject to change at any time and `Qeedji` reserves the right to modify them without notice. This includes the
hardware, the embedded software and this manual, which should be considered as a general guide to the product. The accessories supplied with the
product may differ slightly from those described in this manual, depending on the developments of the various suppliers.
Precautions for use
Please read and heed the following warnings before turning on the power: - installation and maintenance must be carried out by professionals. - do
not use the device near water. - do not place anything on top of the device, including liquids (beverages) or flammable materials (fabrics, paper). - do
not expose the device to direct sunlight, near a heat source, or in a place susceptible to dust, vibration or shock.
Warranty clauses
The `Qeedji` device is guaranteed against material and manufacturing defects for a certain duration. Check the device warranty duration value at the
end of the document. These warranty conditions do not apply if the failure is the result of improper use of the device, inappropriate maintenance,
unauthorized modification, operation in an unspecified environment (see operating precautions at the beginning of the manual) or if the device has
been damaged by shock or fall, incorrect operation, improper connection, lightning, insufficient protection against heat, humidity or frost.
WEEE Directive
This symbol means that your appliance at the end of its service life must not be disposed of with household waste, but must be taken to a collection
point for waste electrical and electronic equipment or returned to your dealer. Your action will protect the environment. In this context, a collection
and recycling system has been set up by the European Union.
3
1.1
1.2
1.3
1.3.1
1.3.2
1.3.3
1.4
1.5
1.6
1.7
1.8
2.1
2.1.1
2.1.2
2.1.3
2.1.4
2.2
3.1
4.1
4.1.1
4.1.2
4.1.3
4.1.4
4.1.5
4.1.6
4.1.7
4.1.8
4.1.9
4.1.10
4.1.11
4.1.12
4.1.13
4.1.14
5.1
5.2
5.3
5.4
6.1
7.1
7.2
7.3
7.4
7.5
7.6
7.7
Table of contents
Part I : Description and installation
Introduction
Labelling
Product faces
Device dimensions
Device fixture
Drilling pattern
Power supply
Device start-up steps
Surround light behaviour at power-up
Connectors pin-out
Procedure to access to the back connectors
Part II : System configuration
Introduction
AQS firmware upgrade
APK deployment
Device configuration by script
Hardware reset
Factory recovery
Part III : Applicative user interface
Applicative user interface
Part IV : Administration console user interface
Administration console user interface
Configuration > Administrator
Configuration > LAN_1
Configuration > WLAN
Configuration > Output
Configuration > Servers
Configuration > Date and time
Configuration > Regionality
Configuration > Variables
Maintenance > Files
Maintenance > Middleware
Maintenance > Preferences
Information > Device
Information > Network
Information > Screens
Part V : Technical information
Technical specifications
Built-in RFID reader
Antenna return loss
Conformities
Part VI : Contacts
Contacts
Part VII : Appendix
Appendix: Qeedji PowerPoint publisher for Media Players
Appendix: Qualified third party references
Appendix: ISO image burning with BalenaEtcher
Appendix: TFTP and DHCP server configuration
Appendix: Timezone
Appendix: Device network disk mounting in MS-Windows explorer
Appendix: USB mass storage
5
Part I Description and installation
6
1.1 Introduction
This manual explains how to install and configure your TAB10s device. It explains also how to install a third party APK and make a AQS firmware
upgrade.
Content of the package
Items Description Quantity
Device TAB10s device with AQS embedded 1
Mounting bracket Bracket for wall mounting 1
Drilling pattern leaflet Drilling pattern 1
Screws M2 x 35 mm (1,37 ") slotted countersunk screw (DIN 963) - a2 stainless steel 2
Adhesive tape 3M double sided tape 4905, material: VHB
W x H x D: 65 mm (2.56 ") x 19 mm (0.75 ") x 0.5 mm (0.02 ") 2
Pads 3M single sided tape, material: silicone
∅: 8 mm (0,314 "), D: 1 mm (0,039 ") 4
Recommendations and warnings
This device is designed to be used indoor and can work 24/7.
The device is delivered without a power supply unit. Depending on your needs, Qeedji is making recommendation for suitable power supply
references in the chapter § Power supply.
◬
Before supply the TAB10s device with the USB connector of your computer, check with your computer's manufacturer that the USB
connectors is suitable to deliver a sufficient power.
◬
In case you had to remove the micro SD card, ensure first that the TAB10s device is powered off before removing or inserting the micro SD
card. In case of bad handling, the micro SD card replacement would not be covered by the warranty.
This device is a Class A device. In a residential environment, this device may cause radio interference. In this case, the user is asked to take
appropriate measures.
☛ In this documentation, the unit of measurement for dimensions is done in millimeters followed by its equivalent value in inches.
7
1.2 Labelling
Product label
These are the labels stuck on the case. They are showing information embedded also in the QR code:
the device model,
the product serial number (PSN),
the MAC addresses.
They are showing also:
the power supply characteristics,
the manufacturer Website,
the conformity logo.
☛ FCC certification in pending.
☛ The QR code on the product label is corresponding to the product identification URL, for example:
i.qeedji.tech?model=TAB10e&sn=01352-00011&mac.wlan1=00-1C-E6-02-4E-90&mac.wpan1=1B-1E-A2-09-DA-B4 .
Packingbox label
This is the label stuck also on the packingbox. It is showing:
the device model,
the QR code embedding the product serial number (PSN),
the manufacturer Website.
☛ The QR code on the packingbox label is corresponding to the product PSN, for example:
PSN01352-00011 CD3 .
☛ The serial number of the device could be requested in case of technical support.
8
1.3 Product faces
Device's front face
1 Touch screen,
2 Camera,
3 Built-in NFC/RFID sensor,
4 ¹.
¹ In the default factory preferences, the distance threshold for the proximity sensor is 1.5 meter. For further information contact support@qeedji.tech.
Device's up face
10 Surround light,
11 Mono speaker,
12 System button²,
13 Built-in microphone n°1,
18 Built-in microphone n°2,
14 Heat pipe.
² The system button is hidden inside the hole.
◬
Do not cover the top of the heat pipe which is designed to evacuate naturally the heat of the device when it is running.
Device's bottom face
10 Surround light,
15 USB-C connector,
16 Mounting bracket orifice/screw n°1,
17 Mounting bracket orifice/screw n°2,
20 USB-C locking orifice n°1,
21 USB-C locking orifice n°2.
1
2
3
4
10
11
12
13
18
14
10
15
16
17
20
21
10
1.3.1 Device dimensions
11
1.3.2 Device fixture
The TAB10s device can be hung on the wall using a mounting bracket (supporting or not the POGO type interface).
◬
To know the device fixture height, refer to the legislation in force in your country, related to the accessibility to disabled persons of
establishments open to the public during their construction and of facilities open to the public during their development.
☛ The legislation in force in France, for example implies to install the top of the display at 130 cm (51,181 ") maximum far from the floor. For the
TAB10s device, add 2.4 cm (or 0,787 ") to this height to determine the maximum height of the top edge of the TAB10s device. For example, for the
France country, the top edge of the device should be (130 + 2.4) = 132.4 cm (52,125 ") far from the floor. So, to find the center of the hole of the
mounting bracket should be at 130 cm (51,18 ") - 8,5 cm (3.35 ") = 121,5 cm (47,83 ").
◬
The TAB10s device is designed to be installed in landscape mode only.
12
Before installing the TAB10s device:
check that the position of the microphone DIP switch and the camera DIP switch is matching the customer needs,
stick, like explained below, the 4 single side tape pads at the back of the TAB10s device, respectively at the 4 corners.
13
14
◬
When installed on the NAPOE109kt or NAPOE109ft products having a mounting bracket with a POGO connector, before mounting the screws
to lock the device, check that the TAB10s device is installed on the NAPOE109kt or NAPOE109ft products stricly on the vertical position else
some unexpected power supply issue could be faced.
15
1.3.3 Drilling pattern
In case you want to hang the TAB10s device on the wall, you can do it using the provided mounting bracket.
Follow the drilling pattern to install it.
This mounting bracket can be fixed using screws (recommended for walls with pierceable material).
☛ The screws and dowels required to fix the mounting bracket on the wall are not provided with the product. They can depend on the wall
material.
Adhesive pattern
If it is not possible to fix the device with screws, for example when needing to be fixed on a glass wall, you can use the provided adhesive tapes.
⚠
Clean carefully the surface before sticking the adhesive tapes.
⚠
Press firmly the mounting bracket against the glass wall before hanging and locking the TAB10s device on it.
16
1.4 Power supply
This device is intended to work with an external power supply, not provided by default. The two ways to supply the device are:
either through the USB-C connector,
or through the POGO type connector.
Power supply references
Depending on your needs, you can order among several power supply unit references recommended by Qeedji.
Commercial reference Model Information
EXC.NAPOE109KT ¹ NAPOE109kt The POGO connector supports power delivery and Ethernet network connectivity
EXC.NAPOE109KU ² NAPOE109ku The USB-C connector supports power delivery and Ethernet network connectivity
EXC.NAPOE109FT ³ NAPOE109ft The POGO connector supports power delivery and Ethernet network connectivity
☛ For supply need only, you can purchase a single 110 V~/230 V~ to USB-C 5 V / 3 A wall plug.
☛ The device can be power supplied by USB-C or POGO type connector. Once supplied by one side, the device won’t never change its power
supply origin, even if the second side becomes available afterwards. The choice of power supply origin is renegociated each time the device is
rebooting; if the USB-C and POGO type connectors are both power supplied, the device will select POGO type connector origin each time the
device is rebooting.
¹ For further information, refer to the NAPOE109kt user manual.
² For further information, refer to the NAPOE109ku user manual.
³ For further information, refer to the NAPOE109ft user manual.
For further information before ordering, contact sales@qeedji.tech.
17
1.5 Device start-up steps
Step 1 (T0 = 0 s)
The device is booting.
Step 2 (T ~ 1 s)
Surround light red
is flashing once:
device powered.
Step 3 (T ~ 8 s)
Qeedji splashscreen
is displayed:
kernel initialization
in progress.
Step 4 (T ~ 22 s)
Android splashscreen
is displayed:
AQS initialization
in progress.
Step 5 (T ~ 30 s)
Nominal mode:
APK is launched.
18
1.6 Surround light behaviour at power-up
State Information
Sequence of 1 short green flash of 300 ms,
periodic in alternance with 4 seconds Off. Error: the used power supply has not enough power to launch the software¹.
Sequence of 2 consecutive short green flashes
of 300 ms, periodic in alternance with 4
seconds Off.
Error: the micro SD card is not present, or has been removed².
Don't forget to power off your device before installing back your micro SD card.
Sequence of 3 consecutive short green
flashes of 300 ms, periodic in alternance with
4 seconds Off.
Error: the micro SD card is unusable or the boot firmware is missing. If the problem persists,
contact support@qeedji.tech.
Sequence of 4 consecutive short green
flashes of 300 ms, periodic in alternance with
4 seconds Off.
Error: an internal issue has been detected during power sequencing. If the problem persists,
contact support@qeedji.tech.
Sequence of 5 consecutive short green
flashes of 300 ms, periodic in alternance with
4 seconds Off.
Error: the micro SD card or the AQS is corrupted and cannot be launched. Follow the factory
recovery process to restore your micro SD card. If the problem persists, contact
support@qeedji.tech.
¹ Try with another suitable power supply unit. If the problem persists despite of an appropriate power-supply unit, contact
support@qeedji.tech.
² Remove the mounting bracket from the device, or remove the device from the mounting bracket, and check that your micro SD card is
properly inserted in the device.
19
1.7 Connectors pin-out
☛ The access to some connectors or DIP switches may require to remove the mounting bracket or remove the TAB10s device from the wall. Refer
to the chater § Procedure to access to the back connectors.
USB-C connector
The device can be supplied by the USB-C connector located at the bottom face of the product.
Information type Value
Type USB type-C
Data USB 2.0
Power USB PD¹ (Power delivery)
This is the USB-C pin-out for the TAB10s:
☛ The USB-C connector is supporting Ethernet over USB.
¹ The TAB10s device is an USB sink device by default, in order to be supplied by an external power source device. It implements data-role swap, in order
to be able to become the data host, and hence, to support ethernet-to-usb external bridges while being supplied by this bridge. When operating in sink
mode, you must take care when selecting your power supply source and usb cable, select a power source able to drive 5 V - 3 A, and choose high quality
cables, especially when you have a long distance between source and the TAB10s device. Qeedji advises to use EXC.NAPOE109KU accessory, as it is fully
qualified with the TAB10s device. The TAB10s device can be an USB source device only when supplied by the POGO type connector. So it can support an
external USB dongle for example. In this case, you have to take care to not sink too much current through USB-C connector.
POGO type connector
The device can be supplied by the POGO type connector located at the back of the product.
1 VCC,
2 GND,
3 USB+,
4 USB-,
5 GND,
6 VCC.
☛ The POGO type connector allows to supply the device and offers an USB 2.0 host interface, for Ethernet over USB for example.
1
2
3
4
5
6
20
Dipswitches for microphone and camera
For confidentiality purpose, the TAB10s device has two switches at the back of the product allowing to activate or inactivate respectively the
microphone and the camera peripherals.
When the DIP switch is facing the crossed microphone, the microphone peripheral is inactivated.
When the DIP switch is facing the crossed camera, the camera peripheral is inactivated.
Example of configuration when the microphone 1 and the camera 2 peripherals are inactivated:
Example of configuration when the microphone 3 and the camera 4 peripherals are activated:
Micro-SD card
The micro SD card connector is located on the rear face of the TAB10s. A micro SD serigraphy is showing the connector location.
Step 1: Place the micro SD card in the right sense close to the connector entry.
☛ It may be required to lift the micro SD card so that it can enter into the connector. Press a little on it to tilt it.
Step 2: Glide the micro SD card in the right sense with the hand towards the micro SD card connector until you feel the spring.
1
2
3
4
Other manuals for TAB10s
4
Table of contents
Other Qeedji Tablet manuals
