Qeedji TAB10s User manual

User manual 001C
TAB10s
9.10.10
TAB10s
8:30

2
Legal noce
TAB10s 9.10.10 (001C_en)
© 2020 Qeedji
Rights and Responsibilies
All rights reserved. No part of this manual may be reproduced in any form or by any means whatsoever. or by any means whatsoever without the wrien permission of the
publisher. The products and services menoned herein may be trademarks and/or service marks of the publisher. or trademarks of their respecve owners. The publisher and the
author do not claim any rights to these Marks.
Although every precauon has been taken in the preparaon of this document, the publisher and the author assume no liability for errors or omissions, or for damages resulng
from the use of the informaon contained in this document or the use of programs and source code that can go with it. Under no circumstances can the publisher and the author be
held responsible for any loss of profits or any other commercial prejudice caused or alleged to have been caused directly or indirectly by this document.
Product informaon
Product design and specificaons are subject to change at any me and `Qeedji` reserves the right to modify them without noce. This includes the hardware, the embedded
soware and this manual, which should be considered as a general guide to the product. The accessories supplied with the product may differ slightly from those described in this
manual, depending on the developments of the various suppliers.
Precauons for use
Please read and heed the following warnings before turning on the power: - installaon and maintenance must be carried out by professionals. - do not use the device near water. -
do not place anything on top of the device, including liquids (beverages) or flammable materials (fabrics, paper). - do not expose the device to direct sunlight, near a heat source, or
in a place suscepble to dust, vibraon or shock.
Warranty clauses
The `Qeedji` device is guaranteed against material and manufacturing defects for a certain duraon. Check the device warranty duraon value at the end of the document. These
warranty condions do not apply if the failure is the result of improper use of the device, inappropriate maintenance, unauthorized modificaon, operaon in an unspecified
environment (see operang precauons at the beginning of the manual) or if the device has been damaged by shock or fall, incorrect operaon, improper connecon, lightning,
insufficient protecon against heat, humidity or frost.
WEEE Direcve
This symbol means that your appliance at the end of its service life must not be disposed of with household waste, but must be taken to a collecon point for waste electrical and
electronic equipment or returned to your dealer. Your acon will protect the environment. In this context, a collecon and recycling system has been set up by the European Union

3
1.1
1.2
1.3
1.3.1
1.3.2
1.3.3
1.4
1.5
1.6
1.7
1.8
2.1
2.2
2.3
2.3.1
2.3.2
2.3.3
2.4
3.1
3.2
3.3
3.4
4.1
5.1
5.2
5.3
Table of contents
1 - Descripon and installaon
Introducon
Labelling
Product faces
Device dimensions
Device fixture
Drilling paern
Power supply
Device start-up step
Surround light behaviour at power-up
Connectors pin-out
Procedure to access to the back connectors
2 - Configuraon
Configuraon with the sengs applicaon
APK
Qeedji System service
APK installaon or upgrade
Configuraon by script
AOSP firmware upgrade
Factory recovery
3 - Technical informaon
Technical specificaons
Built-in RFID reader
Antenna return loss
Conformies
4 - Contacts
Contacts
5 - Appendix
Appendix 1: Qualified references for third party hub
Appendix 2: ISO image burning with BalenaEtcher
Appendix 3: TFTP and DHCP server configuraon

4
1.1 Introducon
This manual explains how to install and configure your device TAB10s. It explains also how to install a third party APK or and realize a OS upgrade.
Content of the package
Items Descripon Quanty
Device TAB10s with AOSP embedded 1
Mounng bracket Bracket for wall mounng 1
Drilling paern leaflet Drilling paern 1
Screws M2 x 35mm sloed countersunk screw (DIN 963) - a2 stainless steel 2
Adhesive 3M double sided tape 4905, material: VHB, W x H x D: 65 mm x 19 mm x 0.5 mm 2
Recommendaons and warnings
This device is designed to be used indoor.
The device is delivered without a power supply unit. Depending on your needs, Qeedji is making recommendaon for suitable power supply references in the chapter § Power
supply.
◬ Before supply the TAB10s with the USB connector of your computer, check with your computer's manufacturer that the USB connectors is suitable to deliver a
sufficient power supply.
◬ In case you had to remove the micro SD card, ensure first that the TAB10s is powered off before removing or inserng the micro SD card. In case of bad handling, the
micro SD card replacement would not be covered by the warranty.
This device is a Class A device. In a residenal environment, this device may cause radio interference. In this case, the user is asked to take appropriate measures.

5
1.2 Labelling
☛ The serial number of the device can be requested in case of technical support.
These are the labels stuck on the case and the cardbox. They are showing informaon embedded also in the QR code:
the device model,
the product serial number (PSN),
the MAC addresses.
They are showing also:
the power supply characteriscs,
the manufacturer Web site,
the conformity logo.
☛ FCC cerficaon in pending.
This is the label stuck also on the cardbox. It is showing:
the device model,
the QR code embedding the product serial number (PSN),
the manufacturer Web site.
Some addional labels may be present in case of built-in opons.
MAC WLAN: 00-1C-E6-02-4E-90
5VInput:
Model: TAB10s
5A rue Pierre Joseph Colin
35000 Rennes, FR
PSN013520-00011 CD3
www.qeedji.tech
2A
MAC WPAN: 1B-1E-A2-09-DA-B4
Contains IC: TBD
Contains FCC ID: TBD
3 7 0 0 5 6 8 1 0 7 4 6 9
TAB10s
www.qeedji.tech

6
1.3 Product faces
Device's front face
1 Touch screen,
2 Camera,
3 Built-in NFC/RFID sensor,
4 Presence sensor.
Device's up face
10 Surround light,
11 Mono speaker,
12 Hardware reset,
13 Built-in microphone n°1,
18 Built-in microphone n°2,
14 Heat pipe.
Do not cover the top of the heat pipe which is designed to evacuate naturally the heat of the device when it is running.
Device's boom face
10 Surround light,
15 USB-C connector,
16 Mounng bracket orifice/screw n°1,
17 Mounng bracket orifice/screw n°2,
20 USB-C locking orifice n°1,
21 USB-C locking orifice n°2.
1
2
3
4
10
11
12
13
18
14
10
15
16
17
20
21

7
Device's rear face
5 Bevelled profile to welcome the mounng bracket,
6 POGO connector,
7 Micro SD card connector with its micro SD card,
8 Microphone DIP switch,
9 Camera DIP switch,
19 20 Holes to host screws heads to fix the mounng bracket.
5
6
7
8
9
19
20

8
1.3.1 Device dimensions

9
1.3.2 Device fixture
The TAB10s can be hung on the wall using a mounng bracket (supporng or not the POGO interface).
◬ The TAB10s is designed to be installed horizontally (landscape mode only).
Before installing, check that the posion of the microphone DIP switch and the camera DIP switch is matching the customer needs.
4 mm4 mm
84.6 mm84.6 mm
78.3 mm78.3 mm
74.3 mm74.3 mm
Wall with pierceable
4 mm4 mm
Glass wall
material
Dowel Double sided tape
M2x35 screws

10
1.3.3 Drilling paern
In case you want to hang the TAB10s device on the wall, you can do it using the provided mounng bracket.
Follow the drilling paern to install it.
This mounng bracket can be fixed using screws (recommended for walls with pierceable material).
☛ The screws and dowels required to fix the mounng bracket on the wall are not provided with the product. They can depend on the wall material.
Adhesive paern
If it is not possible to fix the device with screws, for example when needing to be fixed on a glass wall, you can use the provided double-sided tapes.
⚠ Clean carefully the surface before stucking the tapes.
Casing center
Screws (2x)
6 mm ≤ head Ø ≤ 9.5 mm
Ø ≤ 4 mm
30 mm
255 mm
178.5 mm
30 mm
69.5 mm
h ≤ 4 mm
19.75 mm 89.25 mm
9.5 mm
32.5 mm
36.5 mm
41.7 mm
37.7 mm
Casing
center
255 mm
178.5 mm
76.3 mm
double-sided
adhesives (2x)
27.7 mm
85 mm
85 mm
65 mm
19 mm
74.3 mm
84.6 mm

11
1.4 Power supply
This device is intended to work with an external power supply, not provided by default. The two ways to supply the device are:
either through the USB-C connector,
or through the POGO connector.
Power supply references
Depending on your your needs, you can order among several power supply unit references recommended by Qeedji.
Commercial reference Feature Informaon
EXC.ETH.POGO ¹ POGO wall socket The POGO wall socket is PoE compable and is able to support power delivery and Ethernet over USB
EXC.ETH.USBC ² ETH/PoE to USB-C adaptor The USB-C interface allows to transmit the power delivery and Ethernet over USB
☛ For supply need only, you can purchase a single 110V/230V~ to USB-C 5V/3A wall plug.
☛ The device can be power supplied by USB-C or POGO connector. Once supplied by one side, the device won’t never change its power supply origin, even if the second
side becomes available aerwards. The choice of power supply origin is renegociated each me the device is reboong; if the USB-C and POGO connectors are both power
supplied, the device will select POGO connector origin each me the device is reboong.
¹ For further informaon about the EXC.ETH.POGO wall socket, refer to the EXC.ETH.POGO wall socket's user manual.
² For further informaon about the EXC.ETH.USBC adaptor, refer to the EXC.ETH.USBC adaptor's user manual.
For further informaon before ordering, contact [email protected].

12
1.5 Device start-up step
Step 1 (T0=0s)
The device is boong.
Step 2 (T~1s)
Surround light red is flashing once:
device powered.
Step 3 (T~8s)
Qeedji splashscreen is displayed:
kernel inializaon is in progress.
Step 4 (T~22s)
Android splashscreen:
AOSP inializaon is in progress.
Step 5 (T~30s)
Nominal mode:
end user APK is launched.

13
1.6 Surround light behaviour at power-up
State Informaon
Sequence of 1 short green flash of 300ms, periodic
in alternance with 4 seconds Off. Error: the used power supply has not enough power to launch the soware¹.
Sequence of 2 consecuve short green flashes of
300ms, periodic in alternance with 4 seconds Off.
Error: the micro SD card is not present, or has been removed².
Don't forget to power off your device before installing back your micro SD card.
Sequence of 3 consecuve short green flashes of
300ms, periodic in alternance with 4 seconds Off.
Error: the micro SD card is unusable or the boot firmware is missing. If the problem persists, contact
[email protected].
Sequence of 4 consecuve short green flashes of
300ms, periodic in alternance with 4 seconds Off.
Error: an internal issue has been detected during power sequencing. If the problem persists, contact
[email protected].
Sequence of 5 consecuve short green flashes of
300ms, periodic in alternance with 4 seconds Off.
Error: the micro SD card or the AOSP operang system is corrupted and cannot be launched. Follow the factory
recovery process to restore your micro SD card. If the problem persists, contact [email protected].
¹ Try with another suitable power supply unit. If the problem persists despite of an appropriate power-supply unit, contact [email protected]ech.
² Remove the mounng bracket from the device, or remove the device from the mounng bracket, and check that your micro SD card is properly inserted in the device.

14
1.7 Connectors pin-out
☛ The access to some connectors or DIP switches may require to remove the mounng bracket or remove the TAB10s from the wall. Refer to the chater § Procedure to
access to the back connectors.
USB-C connector
The device can be supplied by the USB-C connector located at the boom face of the product.
Informaon type Value
Type USB type-C
Data USB 2.0
Power USB PD¹ (Power delivery)
This is the USB-C pin-out for the TAB10s:
☛ The USB-C connector is supporng Ethernet over USB.
¹ The TAB10s device is a USB sink device by default, in order to be supplied by an external power source device. It implements data-role swap, in order to be able to become the data
host, and hence, to support ethernet-to-usb external bridges while being supplied by this bridge. When operang in sink mode, you must take care when selecng your power
supply source and usb cable, select a power source able to drive 5V-3A, and choose high quality cables, especially when you have a long distance between source and the TAB10s
device. Qeedji advises to use EXC.ETH.USBC accessory, as it is fully qualified with the TAB10s device. The TAB10s device can be a USB source device only when supplied by the
POGO connector. So it can support an external USB dongle for example. In this case, you have to take care to not sink too much current through USB-C connector.
POGO connector
The device can be supplied by the POGO connector located at the back of the product.
1 VCC,
2 GND,
3 USB+,
4 USB-,
5 GND,
6 VCC.
☛ The POGO connector allows to supply the device and offers an USB 2.0 host interface, for Ethernet over USB for example.
A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12
B12 B1B2B3B4B5B6B7
B8
B9B10B11
VBUS D− D+ CC2 VBUSGND GND
VBUS CC1 D+ D− VBUSGND GNDGND
1
2
3
4
5
6

15
Dipswitches for microphone and camera
For confidenality purpose, the TAB10s has two switches at the back of the product allowing to acvate or inacvate respecvely the microphone and the camera peripherals.
When the DIP switch is facing the crossed microphone, the microphone peripheral is inacvated.
When the DIP switch is facing the crossed camera, the camera peripheral is inacvated.
Example of configuraon when the microphone 1 and the camera 2 peripherals are inacvated:
Example of configuraon when the microphone 3 and the camera 4 peripherals are acvated:
Micro-SD card
The micro SD card connector is located at the back of the TAB10s. A micro SD serigraphy is showing the connector locaon.
Step 1: Place the micro SD card in the right sense close to the connector entry.
☛ It may be required to li the micro SD card so that it can enter into the connector. Press a lile on it to lt it.
Step 2: Glide the micro SD card with the hand towards the micro SD card connector unl you feel the spring.
Microphone DIP switch: Off
Camera DIP switch: Off
1
2
Microphone DIP switch: On
Camera DIP switch: On
3
4

16
Step 3: If the spring of the SD card connector is responding properly, helped with a pen, push the micro SD card towards the connector unl hearing a clic.
The 16 GB micro SD card, containing the AOSP 9 for TAB10s device, is provided by default and is already installed in the product.
The micro SD card is paroned to be compliant with AOSP. This is the micro SD card paron mapping:
Number Name Size File system Funcon
1 dtbo_a 4 MB dtbo.img (device tree)
2 dtbo_b 4 MB dtbo.img (device tree)
3 boot_a 48 MB boot.img
4 boot_b 48 MB boot.img
5 system a 2,5 GB Ext4 Android system files under /system
6 system b 2,5 GB Ext4 Android system files under /system
7 misc 4 MB recovery store bootloader message, reserve
8 metadata 2 MB system slide show
9 persist data 1 MB opon to operate lock\unlock
10 vendor_a 256 MB Ext4 vendor.img
11 vendor_b 256 MB Ext4 vendor.img
12 misc 1 MB state of lock\unlock
13 vbmeta_a 1 MB verify boot's metadata
14 vbmeta_b 1 MB verify boot's metadata
15 userdata 8,4 GB Ext4 applicaon data storage for system applicaon, and for internal media paron, in /mnt/sdcard/ dir.
If you have to remove the micro SD card,
power off the device,
use a lile pen and press on the micro SD card. The spring will eject automacally the card.
If you have to insert again the micro SD card,
power off the device,
use a lile pen and press on the micro SD card unl hearing a clic,
power on back the device.
◬ The warranty does not cover the micro SD card RMA in case it is burnt by a wrong respect of this procedure.

17
1.8 Procedure to access to the back connectors
Do follow this procedure to get access to:
the camera hardware DIP switch,
the microphone hardware DIP switch,
the micro SD card connector,
the POGO connector.
Procedure when the device is supplied by the USB-C connector:
unplug the USB-C cable from the device,
unghten the two screws at the boom of the product,
remove the mounng bracket from the device.
Procedure when the device is hung on the wall with a mounng bracket:
unghten the two screws at the boom of the product,
remove the device from the wall.
The connectors are now visible at the back of the product.

18
2.1 Configuraon with the sengs applicaon
Like any Android tablet, the TAB10s can be configured manually thnaks to the Settings applicaon.
WLAN configuraon
To configure your WLAN interface, in the Sengs menu, choose the Network and internet (Wifi, data usage, hotspot) menu.
The maximum length for WLAN crypto key is:
for WPA-PSK key:
64 hexadecimal characters max.
APK uninstall
To uninstall applicaon, in the Sengs menu, choose the Apps & noficaons (permissions, default apps) menu:
select the appropriate applicaon,
press Uninstall.

19
2.2 APK
The TAB10s is intended to work with one or several custom Android APK. The third party APK are not provided.
The TAB10s is embedding AOSP 9 based on the AOSP SDK 28. To develop your third party APK, Qeedji provides a TAB10s developer manual which is giving links to github to start
to work on AOSP 9 for TAB10s (APK examples) and explains also the procedure to sign the APK requiring the system rights.
To develop your third party APK, Android soware development skills and Android Studio skills are required. For further informaon, refer to the TAB10s developer manual.
Some APK for TAB10s do already exist. For further informaon, contact [e-mail].

20
2.3 Qeedji System service
To support APK deployment, AOSP firmware upgrade and TAB10s device configuraon, the TAB10s embeds the Qeedji System service which is launched automacally as soon as
the AOSP is running. It supports:
APK installaon thanks to a .apk file:
hosted on a USB storage device,
device configuraon thanks to a Javascript configuraon script:
hosted on a USB storage device,
hosted on a TFTP server + DHCP server (code 66),
AOSP firmware upgrade thanks to a .zip archive:
hosted on a USB storage device.