QMTV MV-70/400 User manual

INSTALLATION GUIDE
Video Wall Mount
MV-70/400
Support 32" to 70" Screens
Max Load Capacity: 100 lbs (45 kg)
VESA 400x600 compatible

WARNING
•Be sure to read this entire manual thoroughly and you fully understand all the instructions and warning before
attempting to begin your installation.
This product should only be installed by someone who has a basic knowledge of building construction,installation and
fully understands these instructions.
•
•Make sure that the supporting surface will safely support the combined load of the mount, the display and all
attached hardware and components.
•This wall bracket will only supporting flat panel displays(LCD,Plasma).The maximum load capacity is 100 pounds.
•Always have someone assist you to lift and position your equipment.
•T
•Screws must be tightly secured,but do not overtighten any screws (especially the four hex bolt screws M8x63.5mm)
or damage can occur and product may fail.
ighten screws and bolts firmly, but do not over tighten. Over tightening can damage the items and greatly reduce
their ability to hold. Please refer to suggested torque values where applicable in these instructions.
Tools Needed for Assembly
Required Tools Optional Tools
40mm
6mm 10mm
Before you begin, please verify that all components are included and undamaged. If any
parts are missing or damaged, contact Product supplier, Never proceed with missing or
damaged parts!
Lay out all components and make sure you identify that each one has a match in the
diagram. Some of the parts included will not be used during installation. Do not proceed
if you do not understand and identify all of the components.
2 of 8
•If mounting to a wall of wood stud construction, be sure that mounting bolt are anchored to the center of the studs，
When installing the TV mount on a concrete wall, the wall must be at least 8"(203mm) thick with a minimum comp-
ressive strength from 2500 to 3000 psi (17.2 to 20.7 MPa),the concrete wall must meet ASTM C39. When installing
the TV mount on a cinder block wall, the cinder blocks must meet ASTM C216 specifications and have a minimum
nominal width of 8”(203mm). Be sure to mount in a solid part of the block, generally 1"(25 mm) minimum from the
side of the block.Do not drill into mortar joints! If plaster/drywall is thicker than 16mm,custom fasteners must be su-
pplied by the installer.
6
Table of Contents
Parts List ........................................................................................................................................................................
........
3
Assembly Outline . ... ................... ... .............................. ............................................................................... 4
Install to Solid Concrete or Cinder Block ................................ ........................................................................................
Install to Single Wood Stud Wall ....................................................................................................................................
5
7
Installation of the screen .................................................................................................................................................
8
Product dimensions ........................................................................................................................................................

CD
B
E
A
Magentic Spirit
Level(x1)
hook
F
washer (x4)
1
H
Expansion pipe
M10x61 (x4)
D
E
B
C
H
F
G
with your product.
Parts may appear slightly different than illustrated.
Before you b egin, make sure all parts shown are
included
Parts List
Description
M6x25
philips pan head screw 4
4M8x12
philips pan head screw
4M8x25
philips pan head screw
4
6.2x 16x 1.5
washer(1)
4
spacer(1)
A
M6x12
philips pan head screw 4
4
M10x61
Expansion pipe
Magentic Spirit Level 115x15x40
4
M8x63.5
8.2x 2.0x 16
washer(2) 4
Hex bolt screw
G
Hex bolt screw
M8x63.5 (x4)
2
washer (x4)
3 of 8
bracket
AA BB

4 of 8
STEP1
STEP2
Take out the packaged bracket, push two sides of it by hands, it will open based
on the force of the spring.
Before installation, check the length and the width of the TV, take the TV center as reference
of the install center. ( The tvs have narrow sides, measure the length "x" and width "y")
XX
Y
Y
Confirm the installation environment, then fix wall plate to the wall using the
following methods.
(At least two people are needed)
Assembly Outline

Take out the AA，installation
requires two people
AA
5 of 8
Install to Solid Concrete or Cinder Block
Use wall plate of (AA) as template to mark mounting holes.
Drill four 3/8" (10 mm) dia. holes 2.5" (65 mm) deep.
Insert concrete anchor (H
secure with
M8x 63.5 screws ( G) and Washer 2 (G). Level, then tighten
all fasteners.
•When installing the wall mount to cinder block, verify that you have a minimum of 1-3/8" of actual solid concrete
thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid
part of the block, generally 1" minimum from the side of the block. Cinder block must meet ASTM C-90 specifications.
It is recommended that a standard electric drill set on a slow setting is used to drill the hole instead of a hammer
drill to avoid breaking out the back of the hole when entering a void or cavity.
•Concrete must have a 2000 psi density minimum. Lighter density concrete may not hold the concrete anchor.
•Make sure that the supporting surface will safely support the combined load of the equipment and all attached hard-
ware and components.
WARNING
A
CUTAWAY VIEW
INCORRECT CORRECT
wall plate
plaster/
drywall
concrete wall plate concrete
plaster/
drywall
•Always attach concrete anchors directl to load-
bearing concrete.
•Never attach concrete anchors to concrete covered
with plaster, drywall, or other finishing material. If
mounting to concrete surfaces covered with a finishing
surface is unavoidable, the finishing surface must be
counterbored as shown below. Be sure concrete
anchors do not pull away from concrete when tighten-
ing screws. If plaster/drywall is thicker than 5/8",
custom fasteners must be supplied by the installer.
WARNING
y
•Tighten screws so that wall plate is firmly attached,
but do not overti hten. Overtightening can damage
screws, greatly reducing their holding power.
WARNING
g
concrete
surface
1
3
2
H
Drill holes and insert anchors (H).
Place wall plate of (AA) over anchors (H ) and secure with (G).
Tighten all fasteners.
H
G
solid concrete
cinder block G
AA
H
A
10mm(3/8”)
masony bit

Install to Single Wood Stud Wall
•Installer must verify that the supporting surface will safely support the combined load of the equipment and all attached
hardware and components.
•Tighten wood screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage the
screws, greatly reducing their holding power.
•Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder is
highly recommended.
•Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs. Installers
are responsible for providing hardware for other types of mounting situations.
WARNING
Take out the AA，installation
requires two people
AA
6 of 8
You must secure the mount to two wall studs
with two lag bolts for each stud.
1)
wall studs in the vicinity of the mount.
2) Use a pencil to mark the exact center of each of the
wall studs.
Two people are recommended for this step; one
person to level the mount and another person to
mark the wall stud location.
1) Place the mount against the wall in the desired
viewing location.
2) Adjust the mount to align the mount slots in the
mount with the center of the wall studs.
3) Level the mount.
4) Use a pencil to mark the upper right mounting
location along the center of the wall stud.
A
G
AA
6mm(1/4”)
wood bit
STUD FINDER
(Optional)

7 of 8
(Flat screen is not provided)
WASHER(1)
hook
DAfter the TV is installed, if the TV was not in a flat situation, peaple can turn the
screws, so the pole can be pushed ahead slowly, by this way, the inclination of
the tv can be adjusted. Max adjustable distance is 10mm and all four corners
can be adjusted freely.
B
After the TV is installed, if the TV was not in a horizontal line, peaple
can adjust the tv by the screws, the max adjustable distance is 15mm
and can be adjusted at two sides separately.
B C
DE
F
BB
BB
(Flat screen is not provided)
C
BB
BB
B)A)
AA
BB
F
Installation of the screen
hooks
hooks
(D&E don’t need
F(washer 1))
Spacer(1)
hooks secure the hooks to the mount using the locking tabs on both hooks.
AA
AA
BB

8 of 8
MV-70/400
PRODUCT DIMENSIONS
max to
24.69
627.0
mm
25.98
660.0
mm
1.14
29.0
mm
16.14
410.0
mm
3.15
80.0
mm
2.76 70.0
mm
16.14 410.0
mm
0.16
R4.1
14.03 356.4
mm
[2.59~10.51]
from MIN65.7mm to MAX 267.7mm
Four corners can be adjusted
independently: △10mm
adjustment: △13mm