qp Pansar Supercharged 002 User manual

1/4
Movement Instructions Manual
CAL. VD53B (Manufacturer SII (Seiko) 24-HOUR CHRONOGRAPH
Features
-Hour, minute- and second hands.
-Date
-Stopwatch
-The stopwatch can measure up to 59' 59".
-Split time measurement.
Movement Size 12'''
Outside Diameter 29.50 mm (12H-6H) x 26.00 mm (3H-9H)
Casing Diameter 28.80 mm (12H-6H)
Height 4.57 mm (Include battery)
Battery SR920SW
Battery Life Approx. 2 years
-Battery life indicator.
When the battery nears its end, the second hand moves at two second intervals instead of normal one
second interval. In that case, have the battery replaced with a new one as soon as possible.
Note: The watch remains accurate while the second hand is moving at two second intervals.
PANSAR SWEDEN AB
mässvägen, 125 30 Älvsjö, Sweden

2/4
• Pull crown out to 1st. click position.
• Pull crown out to the 2nd click position when
the second hand is at the 12 o'clock position.
Note: When the crown is in the second click position.
Do not press any buttons. Otherwise the chronograph hands
will move
• Push crown back to normal position.
• Turn the crown clockwise until the previous day’s
date appears.
Note: Do not set the date between 9:00 PM and 1:00 AM.
Otherwise, the date may not change properly.
• Turn to set the hour and minute hands.
• Turn clockwise to advance the hour and
minute hands past 12:00 AM. Doing so will
advance the date to the current date.
• Set the hour and minute hands to the desired
time taking AM or PM into consideration.
Recommended:
• Do not set the date between 9:00 PM and 1:00 AM.
Otherwise, the day may not change properly.
If it is necessary to set the date during that time period, first
change the time to any time outside it, sett the date and then
reset the correct time.
• When setting the minute hand, first advance it 4 to 5
minutes ahead of the desired time and then turn it back to
the exact minute.
Movement Instructions Manual
How to set time and date:
Before setting the time, check if the stopwatch second and minute hands are at the “0” position (12
o’clock). If the stopwatch is in use, press the button in the following order to reset it, and then, check if the
hands return to “0” position.
PANSAR SWEDEN AB
mässvägen, 125 30 Älvsjö, Sweden

.
3/4
Movement Instructions Manual
How to use stopwatch functions:
The stopwatch can measure up to 59' 59" in 1 second increments.
When the measurement reaches 60 minutes, the stopwatch automatically stops counting.
• The measured time is indicated by the stopwatch hands that move independently of the center and
24-hour hand.
• Measurement and release of the split time can be repeated as many times as necessary by pressing
button (B)
• When the measurement is stopped or split time is measured, it stops to indicate the elapsed time.
• After the stopwatch is restarted or split time is released, stopwatch “A” second and- minute hand moves
to current time.
Note: If the stopwatch hands do not return to the "0" position when the stopwatch is reset to "0", follow the procedure in
"How to adjust the stopwatch”.
PANSAR SWEDEN AB
mässvägen, 125 30 Älvsjö, Sweden
Stop ResetStart
Stop Stop ResetStart Start
Split Split
Release Stop ResetStart
Standard measurement
Accumulated elapsed time measurement
Split time measurement

4/4
• Press button (A) or (B) to reset the stopwatch second
and minute hands to “0” position.
• By pressing button (A), the hands move clockwise.
• By pressing button (B), the hands move counter clock-
wise.
Note: Stopwatch second and- minute hands moves quickly if button
(A) or (B) is kept pressed.
.
• Pull the crown out to 2nd. click position.
• Push crown back to normal position.
Movement Instructions Manual
How to adjust the stopwatch:
If the stopwatch minute- and second hands are not in “0” position, follow the procedure below to set them.
PANSAR SWEDEN AB
mässvägen, 125 30 Älvsjö, Sweden