Quicke Q 910 US User manual

2109145 B
01 02 22
AB ÅLÖ - MASKINER
SE -90137 UMEÅ Tel. + (0)90 170500 - Telefax + (0) 90 170599
-series
OPERATOR'S MANUAL
UK
SE
FR
DE
FI
DK
ES
IT
NL

1
(101-501)
ENGLISH
CONTENTS
Page
102 Subframes, Hydraulic Kits
103 Tool Carriers
104 Identification
105 Safety Regulations
106 Warning Decals, Check List
107 Loaders, Level Indicator
109 Attaching / detaching of loaders
110 Attaching of implements
111 Hydr.locking of implements
112 Selecto
114 Selecto Fix
116 Soft Drive
118 Driving Instructions and Maintenance
120 Trouble-Shooting Chart
121 Specifications
122 Warranty Conditions
FRANÇAIS
TABLE des MATIÈRES
Page
302 Bâtis, jeux hydrauliques
303 Porte-outils
304 Identification
305 Instructions de sûreté
306 Autocollants d'avertissement, Liste de contrôle
307 Chargeurs, Indicateur de niveau
309 Attelage / dételage du chargeur
310 Attelage des accessoires
311 Verrouillage hydraulique des outils
312 Selecto
314 Selecto Fix
316 Soft Drive
318 Conseils d'utilisation et d'entretien
320 Dépannage
321 Caracteristiques
322 Conditions de Garantie
DEUTSCH
INHALTSVERZEICHNIS
Seite
402 Fundamente, Hydrauliksätze
403 Schnellwechselrahmen
404 Identifizierung
405 Sicherheitsvorschriften
406 Warnschilder, Kontrollliste
407 Lader, Horizontalanzeiger
409 An- und Abkoppeln von Ladern
410 Anbau der Arbeitsgeräte
411 Hydraulische Geräteverriegelung
412 Selecto
414 Selecto Fix
416 Soft Drive
418 Fahrbetrieb, Wartung und Pflege
420 Störungstabelle
421 Technische Daten
422 Garantiebedingungen
SVENSKA
INNEHÅLLSFÖRTECKNING
Sida
202 Fundament, hydraulsatser
203 Redskapsfästen
204 Identifiering
205 Säkerhetsföreskrifter
206 Varningsdekaler, checklista
207 Lastare, lägesindikator
209 Till- och frånkoppling av lastare
210 Tillkoppling av redskap
211 Hydr. låsning av redskap
212 Selecto
214 Selecto Fix
216 Soft Drive
218 Kör- och skötselinstruktion
220 Felsökningsschema
221 Data
222 Garantibestämmelser
SUOMI
SISÄLLYSLUETTELO
Sivu
502 Soviteosat, hydraulisarjat
503 Varustelevyt
504 Tunnistaminen
505 Turvallisuusohjeet
506 Varoitustarrat, tarkistuslista
507 Kuormain, asennonosoitin
509 Kuormaimen irrotus ja kiinnitys
510 Varusteen kytkentä
511 Hydraulinen varustelukitus
512 Selecto
514 Selecto Fix
516 Soft Drive
518 Ajo- ja huolto-ohjeet
520 Vianetsintäkaavio
521 Tekniset tiedot
522 Takuu
DANSK
INHOLDSFORTEGNELSE
Side
602 Beslag, ventilsæt
603 Redskabsrammen
604 Identificering
605 Sikkerhedsforskrifter
606 Advarselstransfer, checkliste
607 Frontlæssere, redskabsindikator
609 Til- og frakobling af frontlæsser
610 Tilkobling af redskab
611 Hydr. låsning af redskab
612 Selecto (3. funktion)
614 Selecto Fix
616 Soft Drive (dæmper)
618 Kørsels - og vedligeholdelsesinstruktion
620 Fejlsøgningsskema
621 Data
622 Garantibestemmelser
ITALIANO
INDICE
Pagina
802 Sottotelai, kit idraulici
803 Portautensili
804 Identificazione
805 Norme di sicurezza
806 Decalcomanie di avviso, lista di spunta
807 Pale caricatrici, indicatore di livello
809 Connessione / disconnessione di pale caricatrici
810 Connessione di attrezzi (operatori)
811 Bloccaggio idraulico di attrezzi (operatori)
812 Selecto
814 Selecto Fix
816 Soft Drive
818 Istruzioni per la guida e la manutenzione
820 Scheda ricerca guasti
821 Specifiche
822 Condizioni di garanzia
ESPAÑOL
ÍNDICE
Pág.
702 Bastidor auxiliar, juegos de piezas hidráulicas
703 Soportes de herramienta
704 Identificación
705 Reglamentaciones de seguridad
706 Calcomanías de advertencia, lista de comprobaciones
707 Cargadoras, indicador de nivel
709 Enganche / desenganche de cargadoras
710 Enganche de accesorios
711 Bloqueo hidráulico de accesorios
712 Selecto
714 Selecto Fix
716 Soft Drive
718 Instrucciones de manejo y mantenimiento
720 Diagrama de investigación de averías
721 Especificaciones
722 Condiciones de garantía

ENGLISH (102-501)
102
1
23
SUBFRAMES, HYDRAULIC KITS
Description
Before operating your loader, please read this manual
carefully. Failure to do so may jeopardize its efficient
running and could result in a breakdown.
Separate mounting instructions are supplied with subfra-
mes, valves and hydraulic connections, which are
dependent on the tractor model to be used.
This loader is quick-coupled to subframes, which are
available for a large number of tractor models (and
sizes), from various manufacturers.
A subframe kit (Illus. 1) contains all the parts needed to
attach the loader to the tractor, as well as a grill guard*
(A). The subframe kits are of different types, e.g. with
or without* extensions (B) to the tractor rear axle.
The loader can be connected to the tractor hydraulics by
the aid of an Ergodrive Kit, Illus. 2, which contains a
control valve with MONO Handle Device and the neces-
sary connections, or by the aid of a hose kit, Illus.3, to
be connected to the original valves of the tractor. In
cases where a hose set is fitted, the tractor shall be
equipped with two double acting valves.
The loader can, when required, be equipped with Elec-
trical valves (SELECTO) for further hydraulic connec-
tions.
* Depending on tractor- and loader model.

ENGLISH (103-501)
103
10
5
46
TOOL CARRIERS
Description
The loader can be equipped with different types of tool
carriers, depending on the implement attachments - see
fig. 10.
All ALÖ implements of type EURO (8) ( standard) will fit
the loader (fig.6).
There are also COMBI tool carriers as option (depending
on the loader model), which, besides EURO (8), also will
fit implements with attachments of other types, like ÅLÖ
(3), SMS(5), FAUCHEUX(14) and others.
However the implement size must be compatible with the
loader and the type of work to be carried out.
With a few exceptions, the implement will be automati-
cally locked (CLICK-ON) when the implement is lifted
and tilted backwards.
A supplementary equipment for hydraulic
implement change is available to most tool carriers.

ENGLISH (104-502)
104
14
IDENTIFICATION
The machine plate of the loader, which is placed on the
right bearing box ( illus.14), shows:
Loader model, Design, Type of tool carrier, Production
Date (year / month), serial number, Weight and Refer-
ence Number.
For service questions and spare parts requirements
always state serial number and loader model.
Cylinders, valves, control cables* and hoses are also
generally provided with machine plates or punched /
printed reference numbers.
* When ordering control cables, please indicate length
(L) and valve make.
DEFINITIONS
System US / UM / UL
Loder and subframe design, respectively.
US subframe - c/c upright = 900 mm
UM subframe - c/c upright = 1040 mm
UL subframe - c/c upright = 1200 mm
CLICK - ON
Automatic locking of implements.
HYDRAULIC IMPLEMENT CHANGE
Hydraulic attaching / detaching of implements.
HYDRO QUICK
Equipment for the connection / disconnection of the
loaderhydraulics.
LEVEL INDICATOR
Gives the angle of the implement relative to the ground
during lifting and lowering movements.
HOSE KIT
Hoses and hydraulic components for the connection of
the loader to the original valve of the tractor.
ERGODRIVE
Mounting kit containing control valve with MONO lever
remote control and hydraulic connection for the tractor
model in question.
ELECTRODRIVE
Mounting kit as above but with an electr. proportional
valve.
CONTROL VALVE
Valve controlling the lifting- and implement movements
of the loader.
SELECTO
Electric valve to be installed on the front part of the
loader, aimed for implements with hydraulic functions
and loaders equipped with hydraulic implement change.
Operation- of all functions - by the aid of the MONO
lever remote control.
SELECTO-FIX
Quick coupling of hydraulic implements for Quicke front
loaders.
SOFTDRIVE
Shock absorber - improves the driver's comfort and
reduces the strain on tractor / loader when driving on
bumpy ground.
IMPLEMENT ATTACHMENTS
3 = ÅLÖ
5 = SMS
8 = EURO
6 = VALTRA,Vila, Lännen, James (VolvoBM lilla)
9 = Volvo BM (stora)
14 = FAUCHEUX
15 = VETO

105
ENGLISH (105-501)
15
16
This symbol indicates an important safety
regulation.
Faulty use of the equipment could cause serious dama-
ges on man and property - therefore please observe the
following:
- Carefully learn the function of the control device,
attachment of implements etc. before using the loader.
It is also your duty to instruct other persons who are
allowed to use your loader.
Safety Locking Device: The control device is
equipped with a catch, see illus.16, which, in locking
position (left), prevents involuntary operations.
- The tractor shall be equipped with sufficient counter-
weight to ensure the stability of the tractor. See pr EN
12525-1998 !
Please get in touch with your dealer !
- Always check, when changing implements, that the
implement is properly locked in position by pushing the
front part of the implement against the ground.
- Loaded implements shall be transported as low as
possible and at a max. speed of 10 km/h.
- Do not transport round bales or other material with
implements, not aimed for this purpose. In lifted
position the load could tip backwards over the driver.
The tractor shall be equipped with a rollover protective
structure (ROPS) and a falling-object protective
structure (FOPS).
- It is forbidden to stay under lifted loader unless the
shut-off-tap (fig. 15) is in locked position. Unintentional
touch of the control device or leakage in the hydraulic
system might cause sudden movements.
- Lifting and transportation of people is forbidden.
- Be careful when driving with the loader in lifted
position under electric cables - DANGER ! !
- Always check that no people stay in the working area.
- See to it that the necessary electric- and warning signs,
function according to law when driving on public high-
ways.
- The loader is equipped with a shut-off-tap placed as
illustratedonfig.15,ontherightsideoftheloader.Always
see to it that this shut-off-tap is in locked position when
maintainingthemachinery,or when theloaderforsome
other reason has been left in lifted position for a consid-
erable time.
WARNING ! this shut-off-tap may NOT be used when
maintaining the hydraulic system of the loader. In these
cases the loader has to be lowered to ground level.
Turnofftheengineandreleasetheoilpressurebytheaid
of the control valve before disconnecting the quick cou-
plingsormaintainingthehydraulicsysteminsomeother
way - under high pressure oil could cause serious dam-
ages.
- Oil leakages in the couplings, or leakages caused by
damaged hoses, for ex, have to be immediately dealt
with. Check regularly.
- Check and tighten all screws regularly, if necessary,
especially the bolts fixing the subframes to the tractor
body.
- When parking the loader, always attach an implement
(a bucket, a fork etc.). Also see to it that the ground is
reasonably firm and plane.
SAFETY REGULATIONS

ENGLISH (106-501)
106
WARNING
1123492 C
To prevent rollback onto operator
- use special loader attachments
for handling large objects such as
stumps and large round bales.
Transport load as low as possible
to avoid overturning.
Part No. 1123492 C
Part No. 1123493 C
1123493 C
DANGER
Keep machine clear of
overhead power lines to
avoid death or serious
injury.
Part No. 1123491 C
CAUTION
1123522 C
ALWAYS make sure the imple-
ment is LOCKED on the Tool
Carrier before beginning loader
operation.
This can be checked by obser-
ving the locking lever position
and forcing the implement
against the ground using the
loader hydraulic cylinders.
Failure to properly install imple-
ment can cause the implement
to come off the Tool Carrier
resulting in serious injury to the
operator or bystanders.
Part No. 1123522 C
WARNING
1. Add recommended rear wheel
ballast and/or rear counter -
weight for stability .
2. Move wheels to widest recom -
mended setting to increase
stability.
3. Move and turn tractor at low
speeds.
4. In transport carry the load
low.
5. Lower loader to the ground
when parked.
6. Before servicing or adjusting
equipment;
* lower loader to the ground.
* shut of f engine.
7. Relieve hydraulic pressure
before disconnecting oil lines.
8. Observe safety recommend -
ations in Loader Operations
Manual.
1123491 C
(USA / CANADA)
(EUROPE)
(All countries)
11 23 6731123673
!
11 23 674
Part No. 1123674
Part No. 1123673
WARNING !! Check that the implement is locked.
VARNING !!
Kontrollera att redskapet är fastlåst.
ACHTUNG !!
Arretierung des Arbeitsgerätes prüfen.
VAROITUS !!
Takista että varuste on lukittunut.
ATTENTION !!
Veillez au verrouillage de láccessoire.
1123390
Part No. 1123390
CHECK LIST
When the loader has been fitted - check that everything
works properly before use. Always check the following
points. Tick off one by one and adjust , if necessary.
1. Check that the mounting has been carried out
according to the mounting instructions.
2. Check the counter-weight with regard to
implements and field of application.
3. Check that all screws have been tightened.
4. Check that the front wheels don't interfere with
loader and subframe at max. turning angle and
oscillation - if NOT, install front axle stop pieces or
limit the turning angle.
5. Test run of loader.
6. Check that there is no oil leakage.
7. Check oil level in tractor - if necessary, re-fill.
8. When attaching an implement, check that the
locking pins cam in.
9. Check that there are no visible damages on the
loader.
Depending on the regulations /
laws in each country there are
various types of warning decals, of
which these only represent a
selection.
Keep the warning decals clean
and see to it that these are
replaced if damaged or missing.
WARNING DECALS
Please respect the information on the warning
decals !!

107
ENGLISH (107-501)
2
1
3
4
5
LOADERS
Fitting
Check that the marking on the accessory boxes
correspond to the marking on the loader / the subframe.
Except specifying details about the tractor model, the
decal on the accessory box for the subframe also
specifies the number of packages included in the kit as
well as the part numbers - Check this information.
Read the instructions supplied with each kit before
attaching the loader.
Install the subframe and connect the valve or hose kit of
the loader to the hydraulic system of the tractor in
accordance with the mounting instruction.
Lift the loader on to the subframe. There are holes for
the lifting hooks inside the knee plates (see fig.1)
Install the retaining forks acc. fig.2(A) and tighten the
screws (B).
Pass the hydraulic hoses through the U-bolt under the
beam according fig.3.
Connect the hoses to the valve (if there is one mounted)
according to the colour marking (fig.4).
WARNING : always install the loader valve with a return
hose to tank. If this hose is exposed to pressure, the
valve will get damaged.The beam will lift when the
control lever is moved backwards.
Install the level indicator (fig.5) on the implement ram.
Adjustments are made with an implement attached. The
level indicator can be installed on either side, left or right.

ENGLISH (108-501)
108
10
11
12
13
LOADERS
Fitting
The implement rams of the loader are equipped with
safety valves, mounted on the loader cross tube. Fig.10
illustrates the safety valve on loaders without SELECTO.
The SELECTO is equipped with corresponding (built-in)
safety valves (see fig.11).
Note !!
An electric connector for the connection of SELECTO is
included in the ERGODRIVE-kit.
Install the connector on the right subframe (fig.12) and
connect to the current source (12V). Connect earth wire
to tractor body.
Connect the cable from the electric control device to the
connector according to the wiring diagram (fig.13). The
leaders are marked 1,2,3.
WARNING !
Incorrect installation of the cables may destroy the built-
in diodes in the connectors of the valve (SELECTO).
Please study the mounting instruction supplied with the
SELECTO-kit.
Lift the front of the tractor and check that its wheels and
mudguards don't interfere with loader and subframe at
max. turning angle and oscillation.
Since the loader has been tested on tractors of a certain
type (see the List of Subframes) as concerns the hydrau-
lics, cabs, wheel size, mudguards etc, this means that
use with tractors other than these may need special
measures to be taken when attachment is made.

109
ENGLISH (109-501)
32
ATTACHING / DETACHING OF LOADER
Place tractor and loader on plane and solid
ground.
Attach an implement to the loader.
Illustr. 32 A.
- Dump the implement and lower the beam so that the
rear part of the implement is about 10 cms above the
ground.
- Lower the parking legs, which are placed under the
front part of the loader beam.
- Secure the stay to the parking leg (in one of the holes)
by the aid of a pin and a locking pin.
- Release the retaining forks and remove the pins (one
at each side).
Illustr. 32 B
- Lower the loader beam so that the lift rams get
completely compressed.
Illus. 32 C
- Crowd implement carefully. The back of the loader will
then raise and get released from the subframe.
Illustr. 32 D
- Turn off the engine and release the oil pressure to the
loader rams by the aid of the control valve. Use the
float function, if required.
- Disconnect hoses and put dust caps on quick-coup-
lings.
- Reverse the tractor carefully until it is completely
detached from the loader.
NOTE !! make sure that the hoses don't get hooked up
on the tractor.
- These instructions shall be carried out in reverse
order when the loader is attached. Difficulties to
connect the quick couplings are caused by a not
released oil pressure.
WARNING: Never use force on valve cone. The quick-
coupling may be damaged in such a way that it won't
open up properly when compressed (there will be oil flow
in one direction only). Make sure that there is no mix-up
of hoses - note the colour marking.

ENGLISH (110-501)
110
ATTACHING OF IMPLEMENTS
- Move the locking lever in open position (left). This will
be easier if the loader beam is lifted, approx.1 m
(illustr.A).
- Lean tool carrier slightly forwards.
- Drive the loader towards the implement until the
implement hooks hitch the tool carrier (illustr.B).
Loaders with tool carrier EURO (8) and EURO-
COMBI
(CLICK-ON)
- Lift (approx.1 m) and crowd the implement. The
locking lever will be disengaged and the implement
automatically locked (illustr.C).
Loaders with tool carriers equipped with
manual locking
- Lift and crowd the implement. Lock the
implement by moving the lever to the right (illustr.D).
Loaders with tool carriers equipped with loose
latch bolts
- Lift and crowd the implement. Install the bolts and
secure with locking pins (illustr.E).
REMARK ! See the Mounting Instruction for the
hydraulic locking of implements
DETACHING OF IMPLEMENTS
Fig.F
- Lift the implement approx. 1 m.
- Lean the implement approx. 30° forwards.
- Move the locking lever to the left and remove the latch
bolts.
- Lower the implement to the ground. Reverse tractor.
Always check, when changing implements, that the
implement is properly locked in position by pushing the
front part of the implement against the ground.
WARNING
An implement of another origin than ÅLÖ may cause
damage to the loader. Therefore never fit an implement
of another make without making sure that the implement
is approved by ALÖ.

111
ENGLISH (111-501)
1
2
1
HYDR. LOCKING OF IMPLEMENTS
With this device the implement can be ATTACHED /
DETACHED using the control valve of the loader.
The cylinder hoses for the implement locking shall be
connected to the 4th function of SELECTO (fig.1). If the
hoses are switched, the locking device won't work !!
For safety reasons, there is a switch installed on the
MONO-lever remote control, or on the instrument board
of the tractor (see fig.3).
The switch shall be connected to the fixed Selecto-
connector attached on the subframe in front of the cabin
(see fig.2).
Attachment / Detachment (fig. 4)
Instructions:
- Push button D so that red is shown.
- Push button C.
- Move lever to operating position (implement function)
(fig. 4B).
After the locking / unlocking, DON'T FORGET to push
button D again.
Remark !
Regarding loaders equipped with ELECTRO DRIVE,
please note the special selector switch (for the 4th
function) on the Electro Drive control unit. Fig.5, 6
Always check, when changing implements, that the
implement is properly locked in position by pushing the
front part of the implement to the ground.
WARNING
An implement of another origin than ÅLÖ may cause
damage to the loader. Therefore never fit an implement
of another brand without making sure that the implement
is approved by ALÖ.
4
4 B
5
3
6

ENGLISH (112-501)
112
ABC
DE
SELECTO
Description
SELECTO is an equipment preventing overcharge of the
bucket cylinders of the loader and permitting additional
hydraulic functions (one or two double-acting) for the
implements. These are electrically operated by the aid of
a switch, which is fitted on the loader joystick.
SELECTO (3)
This kit consists of:
- A valve (double-acting function)
- Parts required for the connection
- Electr.connectors / cables
The valve is equipped with 1/2" quick couplings. Setting
pressure of built-in security valves: 185 resp. 210 bar.
SELECTO (3+4)
This kit consists of:
- A valve with two double-acting functions. In other
respects, see SELECTO 3.
MOUNTING of SELECTO (3), (3,4)
Fig.A
Remove existing security valve. Secure the valve on the
cross tube of the loader by the aid of three screws (M6S
8 x 20).
Fig.B
Connect the oil pipes and hoses of the loader to the
bucket cylinders.
Fig.C
The connector (30) with bracket is standard in all hydrau-
lic kits (Ergodrive resp. Electrodrive).
Fig. D
Connect cable between connector and valve according
to fig. D.
Fig.E
Connect the cable from the electric control device acc. to
the wiring diagram (the leaders are marked 1,2,3).
The connector (30) shall be connected to the current
source(12V+) and the earth wire to the tractor body.
WARNING !
Incorrect installation of the cables will destroy the built-in
diodes in the connectors on the valve.
REMARK !! Connect after the tractor safety switch. The
electr. cables are supplied with a fuse (8A) to be fitted on
the leader (+) between connector and current source.
Make sure that the connection point is dimensioned for
the power consumption of the valves (5A).
To achieve the "right" function, the connectors (26) shall
be connected acc. fig. D.
Note ! connect the black cable with connector to the right
side (3rd function) of the valve. The red cable with
connector is aimed for the 4th function.
IN GENERAL
After the fitting, fasten the electr. cables by the aid of
supplied strap in order to prevent these from being
exposed to wear / squeezing.

113
ENGLISH (113-501)
1
23
SELECTO
Control
Test run of loader and valve.
Attaching of implements
By releasing the oil pressure - push button "A/C" and
move lever in operating position - the connection of the
quick couplings will be easier.
NOTE ! turn off the engine, but keep the ignition on.
Function
Fig 1, 2
Control lever in operating position for implement function
Push button (A) = Valve (3rd) in function
Push button (C) = Valve (4th) in function
Remark !
The equipment for the hydraulic locking of the imple-
ments shall be connected to the 4th valve function.
Trouble-shooting
If the valve doesn't work, check:
1. The current supply.
That the connector (fig.3) attached to the valve is
equipped with a light emitting diode (LED), which
gives light when the valve is operating.
2. That the voltage really is 12 V. Try with the tractor
engine turned on (the voltage of the battery may be
too low).
3. The connector, fig.3, is equipped with a diode (26 B)
to prevent sparking. Incrrect connection (see fig.E,
previous page) will destroy the diode. In such a case
the connectors (26) have to be exchanged. It won't
help just to correct the faulty connection.
The connector is available as spare part (5024376).
The damaged connectors shall be cut clean from the
cable. Connect the new ones (fig.3).

ENGLISH (114-501)
114
AA1
BB1
CC1
SELECTO-FIX
Description
SELECTO-FIX is an equipment allowing easy connec-
tion / disconnection of the implement hydraulics.
SELECTO-FIX MK3 is adapted to fit loaders equipped
with SELECTO MK3.
SELECTO-FIX is available in two designs:
1) SELECTO-FIX (3) is aimed for the connection of
implements with one doubleacting hydr. function.
Ref.No 301607 (loader part - to be fitted on the valve)
Ref.No 301605 (implement part - to be fitted on the
hydraulic hoses from the implement).
These kits are also used in combination with
SELECTO (3+4) when the loader is equipped with
hydraulic implement locking. This means that the
hoses to the hydr. locking are permanent.
2) SELECTO-FIX (3+4) is aimed for the connection of
implements with two double acting hydr.functions.
Ref.No 301608 (loader part)
Ref.No 301606 (implement part)
Each hydraulic implement shall be equipped with kit
301605 or 301606.
Remark ! concerns loaders equipped with hydraulic
implement locking - the hoses from the hydraulic imple-
ment locking shall NOT be connected via the SELECTO-
FIX implement part. Use kit 301605. This means that
only implements with one double-acting function can be
connected if the loader is equipped with hydraulic
implement locking.
Kit 301607 (for the loader) consists of:
1 Coupling part with two quick couplings (F)
6 Screws MC6S 8 x 60
4 "O"-rings
Kit 301605 (for the implement) consists of:
1 Coupling part with two quick couplings (M)
Kit 301608 (for the loader) consists of:
1 Coupling part with four quick couplings (F)
6 Screws MC6S 8 x 60
4 "O"-rings
Kit 301606 (for the implement) consists of:
1 Coupling part with four quick couplings (M)
MOUNTING OF LOADER PART
Fig. A
(concerns loaders equipped with SELECTO (3)
Remove existing quick couplings / plugs from the front of
the valve.
Secure the SELECTO-FIX loader part to the valve.
Please note the position of the seals (o-rings).
Fig. B
(concerns loaders equipped with SELECTO 3 + 4)
Remove existing quick couplings from the front of the
valve.
Secure the SELECTO-FIX loader part to the valve.
Please note the position of the seals (o-rings).
MOUNTING OF IMPLEMENT PART
Fig. C1
On loaders equipped with hydraulic implement locking,
the quick couplings shall be screwed on to the
SELECTO-FIX loader part (remove existing plugs).
NOTE ! use kit 301605.
Fig. A1, B1, C1
- Remove existing quick couplings from the hydraulic
hoses of the implement.
- Connect the hoses. Check that the movement of the
implement corresponds to the lever movement desired
(control valve). The connection of the hoses to the
coupling part can be inversed (if required).
- REMARK !! check that the length of the hoses is
sufficient at max. dumping movement -at a height of
about 1,5 m.

115
ENGLISH (115-501)
F
CONNECTION / DISCONNECTION
Make sure, when disconnecting imple-
ments, that the bucket rams NOT are in end
position (disconnection under pressure may
cause problems when connecting).
Fig. F
Connection
- Clean the surfaces carefully of loader-and implement
parts.
- Fit the dowels of the implement part into correspond-
ing holes on the loader part (A).
- Make sure that the lever grips the implement part (B)
and move lever backwards until the lever is secured.
- Always when connecting check that the lever is
locked.
Disconnection
- Push button C and move lever forwards.
- Remove the implement part and hitch on to the
implement.
Move the lever to locked position for protection
( IMPORTANT).
SPECIFICATIONS
Dimension of quick couplings: 3/8"
Oil pressure: max. 200 bar (the total pressure on all
couplings (2 or 4).
MAINTENANCE
Always when connecting, clean the surfaces of the
loader - and implement parts carefully.
Oil leakage
The quick couplings may get damaged, either due to
impurities ( not cleaned surfaces before connection) or
due to an exceeding of the max. allowed oil pressure
(200 bar). If this is the case, locate the leaking line and
exchange the damaged coupling - see the spare parts
sheet.
ATTENTION
Faulty use or maintenance of products aimed for high oil
pressures may cause serious damages. It is therefore of
the utmost importance that the instructions are followed
and that damaged or worn out parts are immediately
exchanged.

ENGLISH (116-501)
116
A
BC
SOFTDRIVE
(Shock Absorber)
DESCRIPTION
This equipment consists of two or three accumulators,
depending onthe loader model. It reduces the vertical
movement of the loader when driving on bumpy ground.
By the aid of a shut-off valve the function of the accumu-
lators can be disengaged.
MOUNTING
Fig. A
The oil pipes to the lift rams of the loader are prepared
for the connection of the accumulators and the loader
beam is equipped with a bracket for the accumulators
(see the separate instruction).
DRIVER's INSTRUCTIONS
Fig. B
Accumulators engaged - shut-off valve OPEN, handle to
the right (front view).
Accumulators disengaged - handle to the left (CLOSED).
This position is used when carrying out precision work,
such as handling of pallets and excavation work. It is
also used when an implement has to keep an exact
level.
SPECIFICATIONS
The accumulators (two or three), at a volume of 0,5 l
each, are filled with nitrogen gas (N) with a pressure of
20 bar.
(we reserve the right to make modifications in the
design).
WARNING !
Do NOT open the accumulators. The gas pressure may
cause damages.
Before service / maintenance in the hydraulic system of
the loader:
- Open the shut-off valve to the accumulator.
- Turn off the engine and release the oil pressure by the
aid of the control valve (engage the float function).
IDENTIFICATION
Fig. C
The machine plate (see fig.) indicates:
model, type, production date and reference number.

117
ENGLISH (117-501)
1
SOFT DRIVE
Description / Control
Fig.1
When the SOFT DRIVE is engaged and the shut-off
valve open, the gas in accumulator A will be com-
pressed. The accumulators can now be checked by
measuring the movement of the rams under different
strains (static) at two different pressures.
Since the temperature of the oil and the diameter of the
rams affect this movement, below table will serve as
guidance.
Accumulator B will slow down the movement of the
beam in the opposite direction (UPWARDS).
CHECK OF ACCUMULATOR (A)
1) Connect a manometer to the hose from the loader lift
rams (the +side) (BLUE hose) with the shut-off valve
in OPEN position.
2) Oil temperature - about 20° C.
3) The bucket shall be loaded in such a way that a
pressure of 100 bar is achieved.
4) Measure the distance between the cylinder bearing
and the piston rod bearing (X).
5) Reduce (empty) the load to achieve a pressure level
of 50 bar.
6) Measure the distance between the cylinder bearing
and the piston rod bearing (X). NOTE ! do NOT lift /
lower beam between measurements.
7) The movement (min.) of the piston rod shall comply
with the values specified in below table (A).
CONTROL OF ACCUMULATOR B
1) Connect a manometer to the hose from the loader lift
rams (the -side) (GREEN hose).
2) Push the front part of the implement towards the
ground with the bucket ram until a pressure of 100
and 50 bar respectively has been achieved.
3) Measure the movement of the piston rod and com-
pare with the values below (B).
NOTE !
The warranty period for the accumulators is limited to
twelve (12) months. Depending on the extent of use, the
gas will diffuse in course of time. In such cases the
accumulator must be exchanged.
CYL. Diam. Movement of piston rod ( 100 - 50 bar)
Ackumulator(A) Ackumulator (B)
65/40 mm 10 - 11 mm 18 - 19 mm
70/40 mm 9 - 10 mm 14 - 15 mm
75/40 mm 8 - 9 mm 11 - 12 mm
80/40 mm 15 - 16 mm 10 - 11 mm
90/40 mm 12 - 13 mm 7 - 8 mm
90/50 mm 12 - 13 mm 8 - 9 mm
The following values apply at an oil temperature of 20°C

ENGLISH (118-501)
118
12
DRIVING INSTRUCTIONS AND MAINTE-
NANCE
For maximum stability and to avoid skidding, always
carry implement with load as low as possible.
When driving the implement into the material to be
handled, always make sure that the valve is in a neutral
position, otherwise the front of the tractor tends to rear
at the moment of drive-in, which would entail strains on
both loader and tractor. Keep to the following rules:
NEVER drive at full speed into the material. Select a low
gear for the best traction.
COUNTER WEIGHT: For overloading and safety
reasons, always use counter-balance with weights when
carrying heavy materials or implements with large out-
reach.
See safety instructions, page 105.
Do not leave the tractor with the loader in ”lift” position
and do not stand beneath the load.
When changing implements, always check that the
implement is properly locked in position by pressing the
front end of the implement to the ground.
OPERATING
Applies to loaders with separate control valve
(ERGO DRIVE).
For loaders with ELECTRO-hydraulic mono lever remote
control (ELECTRO DRIVE), see the separate instruction
for this equipment !
The control device (MONO-lever) has the following
functions:
Lever Movement:
Backwards - Loader beam is lifted
Forwards - Lowering of loader beam + floating
position*
Left **- The implement is crowded
Right ** - The implement is dumped
*The floating function is engaged when the control
device is brought maximally forwards. The lever should
then stay in this position. By moving the lever in the
reverse direction, the function will be disengaged.
** Concerns right-hand mounted control device. As
regards the left-hand mounted control device, the
reversed lever movement is obtained by shifting the
hydraulic hoses marked yellow-red. See the instruction
supplied with the hydraulic kit.
Safety Locking Device: The control device is equipped
with a safety lock, see fig.1, which, in locking position
(left), prevents involuntary operation.
Selecto (applies to loaders equipped with electric switch
valves)
The lever knob is equipped with two switches acc. to
fig.2.
Function
Control lever in operating position for implement func-
tion.
Push button (A) = Valve (3rd) in function
Push button (C) = Valve (4th) in function
Remark
If hydraulic implement locking is fitted, see the instruc-
tions for this equipment.

119
ENGLISH (119-501)
1
2
DRIVING INSTRUCTIONS AND MAINTE-
NANCE
LEVEL INDICATOR
The loader is equipped with a level indicator, which gives
the angle of the implement relative to the ground, when,
for example, handling pallets. See "Loader, Mounting".
PARALLELDEVICE
If the loader is lowered or the implement is dumped at
low engine speed, the loader rams may not be totally
recharged, which could lead to the following:
- that the loader beam is lifted if the implement is fully
crowded at ground level.
- that the implement rams get slightly compressed,
which means that you won't have total control of the
implement.
Therefore, make a practice of either increasing the
engine speed when lowering or dumping the implement,
or keeping the control device in operating position until
the implement rams have been recharged (especially
concerning tractors with a low oil flow).
VARIABLE LIFTING HEIGHT
Fig. 2
When an increased lifting capacity is required, move the
lift rams to the lower mounting holes in the bearing box
of the loader (concerns certain loader models).
SCREW UNIONS
Check, after some days’ initial use, that all nuts and bolts
are tightened, especially where the subframes are
secured to the tractor body.After that we recommend
controls at regular intervals in connection with the
maintenance / service of the tractor.
GREASING:
All lubricating points (fig.1) are equipped with greasing
nipples and should be greased at least once a week on
regular use (use lubricating grease, type B.P.
Energrease L.S.-EP2, or equivalent.)
CLEANING
Always keep tractor and loader clean, in particular the
loader rams and valves. When using a high-pressure
water gun, please avoid spraying water directly on valves
and control device.
When disconnecting the loader / the implement, don’t
forget to put dust-caps on the quick-couplings. If you
don't, dirt may get inside the hydraulic system, which will
cause damage and expensive repairs.
OTHER NOTES
Do not forget to check the level of the hydraulic oil and to
change oil and filters regularly as prescribed by the
tractor manufacturer.
Cold and dirty oil will increase the time for the lift- and
implement movements of the loader.