r2p Tracking ProBox 3100 User manual

ProBox 3100
Installation
http://www.r2ptracking.dk
Revision: 030918

The ProBox sends the tracking data by means of GMS/GPRS. A SIM card
is required. Make sure PIN code has been turned off. You may have to
insert the SIM card into a mobile phone to turn off PIN code.
The card is inserted like shown
below. Make sure the card fits
properly into the socket when
socket is closed.
Make sure that the card is
locked properly in both sites
when you push the lid up.
Use a Philips screwdriver
to remove two screws in
the back and remove the
screws before opening
the cabinet.
When SIM card is
inserted, the cabinet is
assembled and screws
are secured firmly.
PROBOX 3100
1

FRONT VIEW
MICROPHONE (NOT USED)
GPS LED
GSM/GPRS LED
PERIPHERAL LED
LED’s
GPS LED
Two (2) blinks pr second = GPS NOT OK
One (1) blink pr second = GPS OK
GSM/GPRS LED
Four (4) blinks pr second = GSM NOT OK
One (1) blink pr second = GSM OK, But NO GPRS
One (1) blink every 4 seconds = GSM AND GPRS OK
ON = Sending data by GPRS
PERIPHERAL LED
Zero (0) blinks every 5 seconds = No peripheral is connected
One (1) blink every 5 seconds = 1 pcs peripheral is connected
Two (2) blinks every 5 seconds = 2 pcs peripheral is connected
Three (3) blinks every 5 seconds = 3 pcs peripheral is connected
PROBOX 3100
2

1 Red Plus, 10-30 volt
2 Black Ground
9 Yellow Ignition
3 Pink Digital 1 In
5 Blue Digital 2 In
7 White Digital 3 In
4 Grey Analog 1 In
6 Green Analog 2 In
8 Purple Digital 1 Out
10 Orange Digital 2 Out
12 White/Red CAN2 H
11 Blue/Red CAN2 L
1
212
11
1
214
13
1 Yellow RS232, B, Rx
3 Orange RS232, B, Tx
5 Purple RS232, A, Rx
7 Pink RS232, A, Tx
9 Green L-line
11 Brown K-line
13 White/Red RS485, A
14 Yellow/Brown RS485, B
2 Black Ground
8 White CAN1 H
10 Blue CAN1 L
12 Black Ground
6 Green/Yellow 1W DATA
4 Red 1W 5 volt
FRONT VIEW
REAR VIEW
GPS antenna
Remove self-adhesive tape
Mount of flat surface Voice, microphone
USB, computer
GPS LED
GSM LED
PERIPHERAL LED
PROBOX 3100
3

A typical installation spot is under the dashboard
but behind or over the glove compartment.
From here you can often run the wires to the
back of the radio where you find the power
and ignition (switched 12 volt).
Always mount the antenna as shown,
pointing up towards the satellites.
Beware of airbags.
Start by finding a good location for the hardware.
Installation-wires can be extended if required.
PROBOX 3100
4

1 Red Plus, 10-30 volt
2 Black Ground
9 Yellow Ignition
FRONT VIEW
GPS antenna
+-
Fuse 3 amp
12/24 volt when ignition is on
Battery
Minimum wiring for tracking:
Ground, 12 volt and ignition.
PROBOX 3100
1
212
11
1
214
13
REAR VIEW
5

1-wire connection
Driver RFID login
6 Green/Yellow 1W DATA
2 Black Ground
PROBOX 3100
1
212
11
1
214
13
White
Black
Green
Red
12/24 volt when ignition is on
8 Purple Digital Out 1
6

White
Grey
Green
PROBOX 3100
1
212
11
1
214
13
7
8 Purple Digital Out 1
Yellow
BrownBrown
250ohm Resistor
}
Not used

Computer USB connection
USB
Software updates / configurator
PROBOX 3100
1
212
11
1
214
13
8

CANCLIQ connection
8 White CAN high
10 Blue CAN low
12 Black Ground
CAN BUS
H L
CANCLIQ
Blue
Yellow
Black
See our manual
CAN BUS DETECTION
if you do not know how to detect
CAN HIGH and CAN LOW.
PROBOX 3100
1
212
11
1
214
13
12/24 volt when ignition is on
Red
9

J1708 connection
13 White/Red J1708 A
14 Yellow/Brown J1708 B
2 Black Ground
J1708
H L
CANCLIQ
Orange
Brown
Black
PROBOX 3100
1
212
11
1
214
13
12/24 volt when ignition is on
Red
10

Red
Black
Purple
Orange
Green (not used)
White (not used)
4 Red, 5 volt
Driver panel connections
PROBOX 3100
1
212
11
1
214
13
11

Tacho Driver Login
PROBOX 3100
1
212
11
1
214
13
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
D C B A
TACHO, REAR VIEW
Tacho, D, 8 K-line, Brown
Pin 11
12

TACHO REMOTE DOWNLOAD
PROBOX 3100
1
212
11
1
214
13
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
D C B A
TACHO, REAR VIEW
Tacho, D, 8 K-line, Brown
Tacho, C, 5 CAN H, White/Red
Tacho, C, 7
CAN L, Blue/Red
Tacho, C, 8
Pin 11
Pin 12
Pin 11
13

TACHO REMOTE DOWNLOAD
PROBOX 3100
1
212
11
1
214
13
Tacho, D, 8 K-line, Pin 11
Tacho, C, 5CAN H, Pin 12
Tacho, C, 7
CAN L, Pin 11
Tacho, C, 8
CAN H, Pin 8
CAN L, Pin 10
CAN BUS
CAN BUS
Interconnections between pins C7 and C8 is
Usually reguired. To check whether you need
To use this interconnections follow these steps:
1. Vehicle IGNITION must be off.
2.C-connector is free
3.Set your multimeter to measure Ohms
4.Measure the resistance between pins C5 ans C7
A) If resistance value is approximatley
equal to 120 , then the interconnection
between pin C7 and C8 is not required.
In this case , connect CAN High wire to C5 pin
and CAN Low wire to C7 pin.
B) If measured resistance is shown to be
infinitely high, then the interconnection
between the pins C7 and C8 is required.
Connect Can High wire to C5 pin and Can Low
wire to C7 and C8.
14

Draeger Interlock 7000
PROBOX 3100
1
212
11
1
214
13
Pin 1 RX
Pin 10 TX
Pin 2 + 9 Ground
5 Purple RS232, A, Rx
7 Pink RS232, A, Tx
2 Black Ground
RJ48
10 Orange Digital 2 Out Pin 14
Pin 16
D8 KLINE
If pin 16 from the Interlock 7000 is connected to pin D8
on the Tachograph, the user switch will be
overruled by the Interlock 7000. If this function is not needed
then disconnect the connection.
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
D C B A
TACHO, REAR VIEW
15
Installation information about Tacho Driver login see page 12
Installation information about RFID login see page 6
Installation information about Ibutton login see page 7
IMPORTANT:
REMEMBER TO CONFIGURE THE DRAGER INTERLOCK 7000 SO THE RS232 OUTPUT IS ACTIVE

Temperature Sensor
4 Red +5v Power
6 Green/Yellow 1W Data
2 Black Ground
Red
Yellow
Black
PROBOX 3100
1
212
11
1
214
13
16

GSM
Jamming Detection
PROBOX 3100
1
212
11
1
214
13
Red Power 10 - 30 volt
Orange Digital 2 Out
1
10
Digital output 2 is enabled when Jamming is detected.
The digital output 2 is an open collector output and
have a maximum rating of 300 mA.
When the digital output is enabled there will be Ground
on the output wire.
If more than 300 mA is needed please use a relay.
If Driver Panel is connected use White wire from the panel.
Driver Panel connections can be found on page 12.
17

3 Pink Digital 1 In
5 Blue Digital 2 In
7 White Digital 3 In
2 Black Ground
Digital inputs
PROBOX 3100
1
212
11
1
214
13
18

Analog inputs
4 Grey Analog 1 In
6 Green Analog 2 In
2 Black Ground
PROBOX 3100
1
212
11
1
214
13
19