Racepak IQ3 Drag Dash User manual

IQ3 Drag Dash Installation Manual
1
IQ3 Drag Dash
Installation Manual
 
IQ3 Drag Dash Release Rev B 021016
Racepak, IQ3 Drag Dash and V-Net are trademarks of Racepak LLC.
© Racepak LLC

IQ3 Data Logger Dash Installation Manual
2


IQ3 Drag Dash Installation Manual
3
Disclaimer
Racepak LLC makes no representations or warranties of any type with respect to the contents in
this manual. Racepak LLC disclaims any implied warranties or fitness for any particular purpose.
Racepak LLC is not liable for any errors contained within or for incidental or consequential
damages in connection with the supply, performance or use of the hardware and software or
this manual.
Racepak LLC reserves the right to revise this installation and user manual at any time, without
obligation to notify any person of revisions. As defined by the Magnuson-Moss warranty Act, do
not install any parts or services unless you have the technical ability to properly set-up the
entire vehicle to compensate for the installation of those parts. The necessary work and
expertise needed to install different products varies. Instructions, where provided, are given to
assist in the installation only; they are not a substitute for mechanical experience in setting up
vehicles. Racepak LLC is not responsible for any personal or property damages caused by the
installation of this product.
Warranty
Racepak LLC makes every effort to ensure our products and services are of the highest quality
and standards. It is our intention to maintain a mutually beneficial and cordial relationship with
each and every customer.
Racepak LLC warrants all merchandise manufactured by Racepak LLC against defects in
workmanship or material for a period of six (6) months after the date of purchase. This
warranty applies to the first retail purchaser and covers only those products exposed to normal
use or service. It does not apply to those products used for a purpose for which said products
were not designed, or which has been altered in any way that would be detrimental to the
performance or life of the product, or misapplication, misuse, negligence, or accident. Any part
or product found to be defective after examination by Racepak LLC will be repaired or replaced.
Racepak LLC assumes no responsibility for diagnosis, removal and/or installation labor, loss of
vehicle use, loss of time, inconvenience or any other consequential expenses.
This warranty is in lieu of any other expressed or implied warranties, including any implied
warranty or merchantability or fitness, and any other obligation on the part of Racepak LLC, or
selling dealer.
If you have any questions regarding warranty, please contact customer service at Racepak LLC.
949-709-5555
Installation of this product may void factory warranty as dealer may wish to verify
mileage/codes/service hours etc. on factory gauge. Install at your own risk. Factory
gauge may be retained and connected for use as a diagnostic tool.

IQ3 Data Logger Dash Installation Manual
4

IQ3 Drag Dash Installation Manual
5
Disclaimer ............................................................................................................... 3
Warranty................................................................................................................. 3
Manual Summary .................................................................................................... 7
Manual Quick View .................................................................................................................................................... 7
Items Included with the IQ3 Drag Dash Display Kit ................................................................................................... 7
IQ3 Drag Dash Features .......................................................................................... 8
General Feature Overview ......................................................................................................................................... 8
IQ3 Drag Dash Displayed Features ............................................................................................................................ 8
Technical Specifications ............................................................................................................................................. 9
IQ3 Drag Dash Functions ......................................................................................................................................... 10
PC Minimum Requirements .................................................................................................................................... 10
DataLink Programming Software ............................................................................................................................. 10
IQ3 Drag Dash Configuration File (software) ........................................................................................................... 10
Data Recording Activation ....................................................................................................................................... 10
Hardware Features ............................................................................................... 11
External Dimensions ................................................................................................................................................ 11
External Features – Front ........................................................................................................................................ 11
External Features – Rear.......................................................................................................................................... 12
Mounting Dimensions ............................................................................................................................................. 12
Installation ............................................................................................................................................................... 14
General Mounting Requirements ............................................................................................................................ 14
Power Supply and Grounding .................................................................................................................................. 15
Engine RPM Signal ................................................................................................................................................... 15
MicroSD Memory Card ............................................................................................................................................ 15
IQ3 Drag Dash Wiring Pinout ................................................................................ 16
External V-Net Sensor Connection (optional add ons 6 maximum) ....................................................................... 19
Factory Default Display Settings............................................................................ 21
External Programming Buttons ............................................................................. 23
Button Programming Modes ................................................................................................................................... 23
General Button Operation ....................................................................................................................................... 23
Button Functions in Setup Mode ............................................................................................................................. 24
Programming in Setup Mode .................................................................................................................................. 24
Display Clock/Time: ................................................................................................................................................. 27
Sensor Hardware Installation: ............................................................................... 28
Oil Pressure and Water Temperature Sensor .......................................................................................................... 28
Driveshaft Collar and Sensor ................................................................................................................................... 30
OBDII and EFI Interface: ........................................................................................ 31

IQ3 Data Logger Dash Installation Manual
6
DatalinkII Software Installation ............................................................................. 33
Configuration Files ................................................................................................ 34
Stand Alone or with V-Net Sensors ......................................................................................................................... 34
Programming the Display Using the DataLink Software ........................................ 35
Com Port Settings ................................................................................................................................................... 35
Reading/Syncing of the Configuration File ............................................................................................................. 36
EFI Interface Programming ..................................................................................................................................... 38
Programming the Display Pages ............................................................................................................................. 40
Programming the Warnings .................................................................................................................................... 42
DataLink II Logging and Downloading ................................................................... 44
Data Download Path ............................................................................................................................................... 44
Setting the Correct Time and Date inside Your IQ3 Drag Dash............................................................................... 45
Clearing Data Files from the Memory Card ............................................................................................................ 46
Initiating a Recording with the IQ3 Drag Dash data logger .................................................................................... 48
Recording Data ....................................................................................................................................................... 48
Configuring the Record Parameters ....................................................................................................................... 49
Naming and Storing the Uploaded Data ................................................................................................................. 53
Viewing Real Time Data on your PC ........................................................................................................................ 55
Setting up the Logger Real Time Telemetry Parameters ........................................................................................ 56
Entering the Datalink Real Time Telemetry Parameters......................................................................................... 56
Starting a Telemetry Session .................................................................................................................................. 57
DataLink II Help Files ............................................................................................................................................... 58
Troubleshooting and FAQ ..................................................................................... 60
DataLink will not communicate with the IQ3 Drag Dash ........................................................................................ 60
V-Net Sensor Channels “lock up” from time to time .............................................................................................. 60
Conclusion ............................................................................................................ 61

IQ3 Drag Dash Installation Manual
7
ManualSummary
This manual makes the assumption that you have installed the most current version of the
DataLink PC software and IQ3 firmware. IQ3 Drag Dash firmware and DataLink updates can be
found at http://www.racepak.com/downloads. As of this writing, the most current DataLink
version is 4.6.0 and the most current IQ3 Drag Dash firmware version is 1.1.
Manual Quick View
The following provides a quick view of the manual layout:
1. IQ3 Drag Dash Features
a. Dash
b. Available channels for display
c. External optional sensors
d. Technical specifications
2. Installation
a. Dash
b. Software
3. Programming The Display
4. Adding Sensors
5. Software Usage
Items Included with the IQ3 Drag Dash Display Kit
Qty. Part Number Description
1 250-DS-IQ3D IQ3 Drag Dash Display Kit (incls. all below items)
1 280-CA-IQ3D Harness/Drag Dash Interface
1 280-CA-VM-TCAPM V-Net Male Terminator Cap
1 890-CA-USBABM-6 USB Programming/Communication Cable
1 810-PT-0150GVT Sensor, analog pressure 0-150 psi
1 810-TR-300 Sensor, analog temperature 0-300°F
1 890-DR-USB-1GB DataLink Software Memory Stick
2 800-SW-PSHBTN Momentary Style Push Buttons, spade terminal
1 N/A Installation Manual


IQ3 Data Logger Dash Installation Manual
8
IQ3DragDashFeatures
The IQ3 Drag Dash is a fully programmable LCD digital display dash that is equipped with an
internal data logger. It has been designed to be used as a standalone unit data logger. All
segments will light up for 1 second at power up. Shortly after segments go to normal mode, the
product version and currently installed firmware will be displayed across the bottom of the
dash for 3 seconds.
General Feature Overview
IQ3 Drag Dash Displayed Features
Using the supplied components in the kit, data from the factory engine control unit (via the
main harness connection) can be acquired for display purposes on the IQ3 Drag Dash. Below is
a list of that information that is available to the end user.
28 Programmable Items on 4 pages
Internal Progressive Shift Light LEDs
4 User Programmable Internal Warning Light LEDs with On-Screen Text Warning
5 Character Programmable Alpha/Numeric Text per Display Channel
Rear Mounted Power/Ground/Adapter/Programming Buttons Input
Rear Mounted V-Net Sensor Connector
Polarized and Shielded, Anti-Glare Coated Display For Sunlight Viewing
Metric and English (SAE) Capable
Dimmable Blue Backlight
Gear Position Indicator
Clock / Time Keeper
2 Remote Switch Inputs (Toggle Pages, Acknowledge Warnings, Basic Setup Parameters)
External Shift Light Output (750mA Max Ground Triggered)
External Warning Light Output (750mA Max Ground Triggered)
Cooling Fan Output to Trigger Fan Relay (Relay required, 750mA Max Ground Triggered)
CAN bus for OBDII or 3
rd
Party ECU’s Interface
6 Additional Sensor Inputs via V-Net (CAN bus)
USB Port for DataLink Communication
Data Recording via microSD memory card
Engine RPM
Driveshaft RPM
Engine Coolant Temperature
Oil Pressure
Internal Progressive Shift Light LEDs
4 Internal Warning Light LEDs
Battery Voltage (Internal)

IQ3 Drag Dash Installation Manual
9
Technical Specifications
Sensor Channels - Defined Below
Available V-Net Data Channels (optional additions) 6
Internal Channels as Defined Below 7
IQ3 Internal Channels Voltage
Engine RPM
Driveshaft RPM
Gear Position
Water Temperature
Oil Pressure
Trans-Brake event marker
Processor Speed 20MHz
Power & Current
Input Voltage 9-18V
Current Draw 350mA - Without warning and shift LED’s
active
Reverse Voltage Protection Yes
Operating Temperature 32 - 140°F / 0-60°C
Mounting Orientation Rear of dash facing direction of travel
Memory
Maximum microSD Card Size
microSD Flash - Included
Supports microSD and microSDHC cards up
to 16GB.
Sample (Logging) Rates of Data Channels
IQ3 Internal Channels 100 Hz Maximum, user adjustable to 1 Hz
Vnet Channels 100 Hz Maximum, user adjustable to 1 Hz
Engine RPM Input 50% duty cycle, 5-18V square wave signal
Start Logging Channel (factory default) Either pushbutton held for +5 seconds

IQ3 Data Logger Dash Installation Manual
10
IQ3 Drag Dash Functions
The IQ3 Drag Dash is the main component of the system, as it contains the data logger and
microSD memory card.
PC Minimum Requirements
Windows® XP / Vista / 7 / 8 / 10 operating system
USB 2.0 Port/ 1024 x 768 or higher monitor resolution
DataLink Programming Software
The DataLink software is used to both set up and configure the IQ3 Drag Dash. It will be used to
modify any settings, page layouts, warning light settings, etc. The DataLink software requires a
Windows based PC with a USB 2.0 port for communication. Programming cable is supplied in
the kit.
IQ3 Drag Dash Configuration File (software)
The Configuration File contains the programming settings for both the dash and any internal
and external sensors utilized by the IQ3 Drag Dash. Any additional sensors that were not
shipped with the IQ3 Drag Dash will require updating and syncing of the configuration file.
Data Recording Activation
Any active channel may be used to start logging. From the factory, the IQ3 Drag Dash is
programmed to start logging if either pushbutton is held for at least 5 seconds and stops
logging when power is switched off on the dash. A data file is written every 3 seconds to the
memory card during recording. When power is switched off, the last 3 seconds of data may not
have been written to the card to so take note of this. Once written to the card, the file is
numbered in subsequent order (1,2,3,etc). The start logging channel may be changed to any
valid sensor channel, by the user.
Terminology
In order to assist in the installation and usage of the IQ3 Drag Dash, the following provides an
outline of the most commonly used words that will be encountered in this manual:
Analog: Data created by the reading of a voltage change sent from a sensor.
Calibrate: The process of assigning values to sensor voltage output, in order to graph and analyze the sensor data.
CAN bus: The specific name of the technology utilized to create the V-Net sensor system.
Channel: The input from one sensor.
Digital: A sensor or signal that has only two values, off or on such as the measuring of ignition pulses to calculate Engine
RPM.
HZ: Number of times per second. Used to define sample rate. Example: 4Hz represents data that is saved 4 times (every
.250) per second.
Sensor: A device that converts a physical property, such as pressure into a voltage signal.
Transducer: See Sensor.
V-Net Channel: Any sensor that is connected to the V-Net port of the IQ3 Drag Dash.
V-Net: Racepak exclusive that allows multiple sensors (analog or digital) to transmit their data over a single cable, back to
the IQ3 Drag Dash.

IQ3 Drag Dash Installation Manual
11
HardwareFeatures
External Dimensions
External Features – Front
Shift Lights Fully programmable sequential shift lights
Coolant Temp Warning Pre-set warning lights for high engine temperature >225°F
Oil Pressure Warning Pre-set warning light for low oil pressure <20psi
Warning Lights 3 & 4 User programmable warning lights for Inputs 3 & 4
Micro SD Car Slot Location for removable memory card for data recorder
Shift Lights
Oil Press
Coolant Temp
Warning 3
Warning 4
Shift Lights
Micro SD Card Slot
4.1” (10.5cm)
7.3” (18.6cm)
2.1” (5.3cm)
1” (2.54cm)

IQ3 Data Logger Dash Installation Manual
12
External Features – Rear
V-Net Connector Provides input for external sensor(s) V-Net cable
Amp 34 Pin Connector Provides input for power / ground / programming buttons
USB Cable Connector Provides input for USB programming cable supplied with package
Mounting Studs & Nuts Three #10 studs and 10-32 nuts facilitate mounting
Mounting Studs / Nuts (3 total)
V-Net Connector
USB Cable Connector
34 Pin Connector

IQ3 Drag Dash Installation Manual
13
Mounting Dimensions
Mounting template for printing and drilling. Verify printed dimensions on Racepak unit before drilling

IQ3 Data Logger Dash Installation Manual
14
Installation
The design of the IQ3 Drag Dash kit greatly simplifies the installation process, as there is no
external data logger or related components necessary. However, there are basic guidelines that
must be followed in order to ensure correct operation of the product.
General Mounting Requirements
The IQ3 Drag Dash is designed to be utilized in a race vehicle environment and is designed as
such. However, there are external conditions that can influence the operation and longevity of
the product and associated wiring.
Heat
Avoid excessive heat, such as generated from exhaust systems, transmissions, etc.
ElectricalInterference
Avoid electrical interference. Vehicles generate electrical interference from a variety of
locations such as ignitions, alternators, ECU, spark plugs, coils and radio/GPS/telemetry
antennas. This interference can affect the signals generated by any or all of the sensors that
relay information back to the dash.
Moisture
Avoid excessive moisture. The IQ3 Drag Dash is designed to be water resistant but not
waterproof. This means when installed in open cockpit type of vehicles (such as, dragsters,
roadsters, etc.) it is safe for use in light rain but not designed to be subject to immersion of
water. Excessive water buildup can enter dash and damage the unit.

Cleaning
Clean glass lens initially with a lint-free, non-abrasive (microfiber type) cloth. Do not apply too
much pressure to the screen. If using a cleaning solution, DO NOT use an all-purpose cleaner
with acetone, ammonia-based or alcohol, since they can take off the dash’s protective coating.
100% distilled water and/or 50%/50% distilled water and white vinegar is best. Heavy dust and
dirt can be blown away by using small cans of compressed air made for cleaning camera and
computer equipment. 

MountingOrientationofIQ3DragDash
It is important to insure the IQ3 Drag Dash cannot become dislodged during use. Three #10
studs are provided in order to provide secure mounting. If desired, the studs can be unscrewed
from the threaded inserts located in the dash housing.
Perpendicular to travel
Direction of travel

IQ3 Drag Dash Installation Manual
15
Power Supply and Grounding
The IQ3 Drag Dash should be connected to a battery source that can supply a constant 12-18
volts. In vehicles that utilize a master power switch, it recommended to connect to the master
power switch. This not only insures the IQ3 Drag Dash will be powered when the vehicle is in
use, it also insures power will be disconnected in the event of an emergency.
A good ground is very important to the function of the IQ3 Drag Dash. Insure there is no type of
paint, rust or any other type of material that could prevent proper grounding. Boats often
present unique grounding problems. If necessary, provide an isolated power and ground as
faulty grounds will create corrupt data.
Warning: Do not attempt to connect or disconnect any IQ3 Drag Dash item, with the
power switched on. This action could result in damage to the IQ3 Drag Dash.
Engine RPM Signal
Requirements: 5-18V, 50% duty cycle, square wave output. This signal is typically obtained from
the tach signal output of an aftermarket ignition box. Racepak also offers a GMR Inductive RPM
Pickup (Racepak PN: 680-SN-GMR) which can be attached to the +12V coil power on coilpak or
coil on plug ignition systems. For early model points/distributor ignition systems, MSD offers a
tach signal generator, PN 8913 that can be spliced into the 12V power to the coil.
Warning: Do not connect the tach input wire directly to any part of the ignition coil.
Doing so will result in damage to the logger.
MicroSD Memory Card
The IQ3 Drag Dash is equipped with a microSD memory card. This card is located in the face of
the IQ3 Drag Dash, between the shift lights. The card may be removed by simply pressing on
the card, which will slightly eject the card from the dash face. When inserting the card, insure it
firmly “clicks” into place. The edge of the card should slightly protrude from the dash face,
when seated. The IQ3 Drag Dash supports standard microSD or micoSDHC cards up to 16GB
 

IQ3 Data Logger Dash Installation Manual
16
IQ3DragDashWiringPinout
Connector Pinout
Pin
Position Description Color Function / Wiring
1 Battery Positive Red
Connect this input to a fused power source
that is hot only when the ignition switch is on.
We recommend using a 3 to 5 amp fuse when
making this power connection. The safe
operating voltage range is 9 – 18 volts DC.
2 Not Used N/A
3 Not Used N/A
4 Not Used N/A
5 Trans brake Blue
Connect to the trans brake button output
signal or trans brake solenoid terminal on
delay box. IQ3 Drag Dash is defaulted for a
voltage triggered signal. If a ground triggered
signal type is required, user can change this
inputs expected signal type using the
DataLink II software.

IQ3 Drag Dash Installation Manual
17
Pin
Position Description Color Function / Wiring
6 Tail Lights
(Dim lighting) Light Green
Connect to the “lights” signal circuit on the
vehicle. Applying power to this input will
cause the IQ3 Drag Dash to go into night
mode (dimmed settings for all lights will be
used).
7 Not Used N/A
8 External Shift
Light Orange/White
Optional, if an external remote shift light is
desired. Connect to the negative side of the
shift light. Apply a fused 12 volt power
source that is hot only when the ignition
switch is on to other terminal on shift light.
This output applies ground to the circuit
when shift point values are met. 750mA
ground sink maximum
9 Tachometer Yellow
Connect this input to the tach output signal
from your ignition box. The tachometer
input requires a standard 5 – 20 volt, 50%
duty cycled square wave signal to work
properly. DO NOT CONNECT THIS WIRE
DIRECTLY TO THE IGNITION COIL. DOING
SO CAN DAMAGE THE CIRCUIT.
10 Not Used N/A
11
Oil Pressure
Sensor Power
5v output
Red
Connect to the supplied oil pressure sensor
Short circuit protected, 50mA max
(shared between all Sensor 5v outputs)
12
Oil Pressure
Sensor Ground
Black Connect to the supplied oil pressure sensor
13 Oil Pressure Signal Clear Connect to the supplied oil pressure sensor
14 Sensor 5v output
(not used) N/A
Not used for factory supplied sensors.
Optional, available to supply regulated 5
volts out for aftermarket sensors.
Short circuit protected, 50mA max
(shared between all Sensor 5v outputs)
15 Sensor ground
(not used) N/A
Not used for factory supplied sensors.
Optional, available to supply ground for
aftermarket sensors.
16 Sensor signal
(not used) N/A
Not used for factory supplied sensors.
Optional, available to accept signal for
aftermarket sensors.

IQ3 Data Logger Dash Installation Manual
18
Pin
Position Description Color Function / Wiring
17 CAN High Yellow CAN High for ECU connections if applicable
18 Cooling Fan Violet/White
RELAY REQUIRED
(Do Not Connect to Fan Directly)
Optional, if a cooling fan control is desired.
Connect to the negative side of cooling fan
relay; typically pin 86 on a standard
automotive relay.
This output controls ground to the circuit
when cooling fan on/off value is met.
750mA ground sink maximum
See the Cooling Fan Wiring Diagram below
19 Sensor 5v output
(not used) N/A
Not used for factory supplied sensors.
Optional, available to supply regulated 5
volts out for aftermarket sensors.
Short circuit protected, 50mA max
(shared between all Sensor 5v outputs)
20 Sensor ground
(not used) N/A
Not used for factory supplied sensors.
Optional, available to supply ground for
aftermarket sensors.
21 Not Used N/A
22 Sensor 5v output
(not used) N/A
Not used for factory supplied sensors.
Optional, available to supply regulated 5
volts out for aftermarket sensors.
Short circuit protected, 50mA max
(shared between all Sensor 5v outputs)
23 Coolant Temp
Sensor ground Black Connect to the supplied water temperature sensor
24 Coolant Temp
Signal Clear Connect to the supplied water temperature sensor
25 CAN Low Green CAN Low for ECU connections if applicable
26 Battery Ground Black Connect this input to a battery ground
27 Ground
(not used) N/A
Not used for factory supplied sensors.
Optional, available to supply ground for
aftermarket sensors.

IQ3 Drag Dash Installation Manual
19
EXTERNAL FAN OUTPUT WIRING DIAGRAM
Optional – Not required for normal dash operation
Pin
Position Description Color Function / Wiring
28 Ground
(not used) N/A
Not used for factory supplied sensors.
Optional, available to supply ground for
aftermarket sensors.
29 Remote Switch 2 Gray/White
Connect to a normally open momentary
pushbutton. Momentarily grounding this
input will activate button 2 circuit.
See button functions later in this manual for
complete description of all button functions
30 Remote Switch 1 Brown/White
Connect to a normally open momentary
pushbutton. Momentarily grounding this
input will activate button 1 circuit.
See button functions later in this manual for
complete description of all button functions
31 Driveshaft RPM
Sensor 12v output
Red Connect to the supplied driveshaft sensor
Short circuit protected, 50mA max
32 Driveshaft RPM
Sensor Ground Black Connect to the supplied driveshaft sensor
33 Driveshaft RPM
Sensor Signal Clear Connect to the supplied driveshaft sensor
34 External Warning
Light Orange/Yellow
Optional, if an external remote warning light
is desired. Connect to the negative side of
the remote warning light. Apply a fused 12
volt power source that is hot only when the
ignition switch is on to other terminal on
warning light. This output applies ground to
the circuit when warning parameter values
are met. 750mA ground sink maximum
ExternalProgrammingButtonandFanoutputWiringDiagram
BUTTON WIRING DIAGRAM
chassis
ground or
IQ3 pin 4
to IQ3 connector
PUSH BUTTON SWITCH
To chassis
ground
Violet/White wire from IQ3
Sinks to ground when
activated
750mA maximum
Fan Output (12 volt relay required)
To fused ignition
switched + 12 volts
To +12 Battery
Cooling Fan

IQ3 Data Logger Dash Installation Manual
20
External V-Net Sensor Connection (optional add ons 6 maximum)
When installing any optional additional sensors to the IQ3 Drag Dash, it will utilize the Racepak
V-Net (CAN bus) for input. These added sensors are connected using “stackable” modules that
connect to the round 5 pin V-Net port on the rear of the dash. This design provides the ability
to transmit all sensor data through a single cable by use of these “stacking” modules. A cap is
then placed at the end of the “stack” to terminate the system. The modules are typically
available with sensors in kit form. Extension cables are available in a variety of lengths to
connect multiple “stacks” of modules that may be installed in different locations throughout
the vehicle.
To add sensors, the customer simply measures from the IQ3 Drag Dash to the mounting
location of the “stackable” module or modules, and orders the appropriate length pre-
terminated V-Net extension cable. V-Net cables are available in 12” increments and are
equipped with a male connector on one end and a female
connector on the opposite end. In the event sensors are
mounted in multiple locations throughout the vehicle, simply
measure between each sensor location and order the necessary
V-Net extension cables to connect all items to the main V-Net
cable routed to the rear of the dash.
Any V-Net sensor currently offered by Racepak may be utilized by the IQ3 Drag Dash. For a
complete listing of available sensors, visit our website located at www.racepak.com or contact
the Racepak customer service department at 949-709-5555 for a catalog. Customer supplied
sensors may also be utilized. DataLink software is used to both set up and configure the IQ3
Drag Dash using a Windows based PC. It will be used to modify any settings, page layouts,
warning light settings, add additional sensors, etc. See Programming the Display Using the
DataLink Software section shown later in this manual for further details.
Sensors
Terminator
cap
V-Net Extension Cables
V-Net Modules